Search Documents

By Torres F, Cerda I, Gimenez P, Gonzalez G, Castelli L

Slurry density measurement, specially in cyclone feed streams, is fundamental to grinding circuit control. With the purpose of increasing the availability of such a measurement, the design of a soft-sensor in an actual grinding plant is addressed in this paper. The system is designed to substitute the momentary unavailability of the real density sensor, either because it has failed or because it has been removed for any other reason. The ARMAX model structure is determined using the stepwise regression method. Starting with a list of the candidate variables, the method selects, one by one, and in a systematic manner the variables which best model the measurement to be replaced, choosing them from the set of presumably correlated candidate variables. In this paper not only the single measurements are included in the list of candidates, but also combinations of such measurements having physical significance. A phenomenological model has been built with the purpose of determining these combinations. It turned out that in most of the cases the components of combined measurements having physical significance were selected by the stepwise regression method, instead of the single measurements. Actual grinding plant data is used to determine the model structure, to estimate the model parameters and to test the predictive capability of the developed soft-sensors. Good results are shown to be obtained during periods of up to 30 hours of the density soft-sensor operation.

Jan 1, 1995

By Frith RT, M D. Goodz

Drilling has been accepted as a major exploration tool. However its use in mine planning and development has been overlooked.This need for drillhole data was highlighted during the redevelopment boom of the central Victorian gold mines. During the 1980's numerous old mines were evaluated and successfully drilled to yield mineable parcels of quartz reefs close to existing workings.Invariably the initial decision was always to attempt reopening and rehabilitating existing access. The four case studies described have proceededsufficiently to show that major cost savings would have been made if underground drilling had been used as the main tool in mine planning.Savings not only in expenditure, but in the time required to make key decisions. In two cases the mines would have experienced far earlier expansions in production. In one case the mine would be currently producing rather than awaiting further finance. In the fourth example, the decision to case development would have been much earlier providing capital to other projects.

Jan 1, 1990

By K Biegaj

During the author’s 25+ year career in mine management in various parts of the world (mostly in Australia), the author has been privileged to live and work in mining towns (not FIFO) for more than 20 years. And has personally observed other people from the mining industry carrying out work at home in an unsafe manner, eg pushing lawn mowers whilst wearing thongs or performing electrical jobs whilst standing on aluminium ladders, as well as many others. It is common that injuries sustained at home whilst on break are not reported upon arrival back on a mine site. A large number of compensation claims for injuries at work, which in fact had been sustained at home, come at substantial extra costs to mining companies.

May 5, 2022

When Matthew Flinders entered in his log `This land forms the South side of the large bight; and besides projecting beyond the coast line, and being a little higher than usual is remarkable for having some reddish cliffs in it, and deep water near the shore', he was commenting on the deposit of bauxite at a place now known as Weipa. This sighting took place on 9 November 1802, and probably represents the first direct entry in Australia acknowledging a potential mineral deposit. Flinders, of course, had no idea as to what he was looking at, nor did he land to determine its content. If he had, he probably would have had no idea of the substance, and even less knowledge of its use. Nothing further was done to this for about 150 years.

Jan 1, 1993

By Gonzalez JM

The Pao gold prospect in N. Luzon, is an example of a high sulphidation epithermal gold system hosted in Mid-Tertiary alkaline volcanics, in the Philippine Arc. Styles of mineralization include: quartz-enargite veins, vuggy silica alteration bodies, and pervasive low grade (0.5ppm) gold mineralization, associated with kaolinite-pyrite-quartz alteration, and geochemically characterized by high As and Hg. Early magnetite-epidote-chlorite alteration linked to an unexposed granitoid is overprinted by an extensive zone of advanced argillic alteration (kaolinite-pyrite-quartz). No alunite is recorded. Important controls of mineralization include; a broad anticline intersected by axial faults, permeable pyroclastic units, and upward confinement of the alteration system by a highly impermeable, clay-rich volcanic unit. At this stratigraphic position the most important mineralization waz developed. The Pao high sulphidation system is not closely related to a stratovolcanic centre, and has formed subsequent to deformation of the volcanic field. It may, however, be related to an unexposed comagmatic intrusion.

Jan 1, 1990

By Ault A. R

The recent modernisation program at the Risdon electrolytic zinc smelter of Pasminco Metals - EZ (PMEZ) inyolved significant changes to the composition of cell electrolytes. The most significant were increased acidity and sulphate level, a reduction in Co level, and the replacement of 2-naphthol in the additive mixture with licorice. In determining acceptable operating ranges, a relatively large number of industrial deposition tests under controlled conditions was required. The cathode zinc deposits so produced were examined in terms of overall appearance, crystal structure according to X-ray diffraction, and a micro-roughness parameter. Beginning with typical deposits produced in the presence of an excess of one of the addition agents glue or antimony or a mist suppressant (licorice or 2-naphthol), a simple classification system was developed. In this system, the deposits are divided into the following types: Doughy, Pinholed, Compact and Stressed. There was a weak correlation between deposit type and crystal orientation. In terms of ease of stripping, observations in plant operations showed that only Compact and Pinholed were consistently acceptable. Current efficiency was normally maximised by producing a Compact deposit. Process variables such as zinc concentration, temperature and the use of strontium carbonate were found to cause changes in deposit type if the reagent mixture used was unchanged. From the knowledge gained, guidelines were developed to allow glue and antimony additions to be altered to fit new circumstances. The simple classification system was first used to expedite recovery from undesirable morphologies and then to optimise individual cell units operated under substantially different conditions. It is believed that finer control could be exercised by determining the micro-roughness of Compact deposits. However, difficulties can arise if sudden, large deviations occur and go undetected. Suggestions are given for an improved additive control system. The classification system developed has been compared with published information in the literature, and good correspondence was noted suggesting a predictable relationship between short-term, laboratory deposition tests and observable phenomena in industrial electrowinning cells run under steady conditions.

Jan 1, 1993

By Albano C, Antila A, Flykt B

A method for relating operating variables and dewatering parameters of Thunes disc filters in the LKAB pelletizing plant at Malmberget in Sweden, via empirical mathematical models is described. Near orthogonal experimental design was used, where all independentvariables were allowed to span over their domain of variation and pseudo-randomly distributed among the experiments. The dewatering parameters are dependent on many variables and instead of using a traditional mechanistic model, an empirical model based on multivariate data analysis was chosen. The way of expressing the relation is by regression coefficients obtained from partial least square regression (PLS). Two empirical models were generated. The models were validated using an extra set of 56 experiments. The dewatering parameters were related to the design variables with few experiments, and user-friendly response surface methodology was used to determine the optimal conditions.

Jan 1, 1989

The United StatesÆ reporting standard for the mining industry for securities purposes is contained in the Security and Exchange CommissionÆs Industry Guide 7. It defines proven and probable Reserves using its own definitions, and prohibits the disclosure of quantitative estimates, for all mineralisation other than those two Reserve categories (though disclosure of Measured and Indicated Resources as quantitative mineralised material estimates is now informally allowed). Similarly, it restricts disclosure of value estimates to Reserves only, which SEC policy generally requires to be on an historic cost accounting basis. The SEC does not maintain a formal Competent or Qualified Person policy. In March 1999, the US-based Society of Mining, Metallurgy and Exploration (SME) released an update of its 1991 guidelines for definitions to be used in reporting of Mineral Resources, Reserves and Exploration Information, closely abiding by the 1997 CMMI recommendations. However, without SEC recognition, reporting under the SME and CMMI definitions is effectively barred for US companies. The SEC intends to adopt the International Financial Reporting Standards (IFRS) of the International Accounting Standards Board (IASB). This will occur within just a few years, when the convergence project for development of the IFRS has reached a satisfactory point. The US is the largest financial supporter and participator in IASB. The Extractive Industries Standard of the IFRS will likely terminate Industry Guide 7. However, the effect of this international replacement will likely be equally restrictive. This could possibly neutralise the benefit of a CMMI-based global reporting standard. SME, the US society encompassing the widest range of mining industry professionals, does not have a Code of Ethics. It has no mechanism for requiring members to abide by a professional standard. SME is presently looking into possible solutions for this deficiency. US-based professional societies that do have a binding Code of Ethics, generally cater to a single profession, and are not just mining industry related. The American Institute of Professional Geologists (AIPG) and the American Institute of Minerals Appraisers (AIMA) are examples. The SME is considering creating a subsidiary body with an enforceable Code of Ethics. To support a CMMI-based global reporting standard, competent persons will need to work across international borders. A standardised mechanism for qualifying and registering competent persons will be needed. National rules and laws must allow competent persons to easily enter countries to perform their work. State issued licenses are increasingly required for much of the work performed in the US mining industry by engineers, geologists and minerals appraisers (valuers). Such licenses are not required by the SEC for Reserve reporting in the US, may not be required for valuation of mineral properties under certain circumstances, and except for real property valuer licenses, they generally do not have a binding code of conduct. However, state licensing of professionals forms a substantial and increasing barrier to interstate trade in professional services, and can be a prohibitive barrier to professionals from outside the US. Any rationalisation of this confusing patchwork of regulations confronting US minerals industry practitioners will only occur as part of larger, national change, hopefully aimed at compliance with international standards and protocols. The US does not have a valuation standard aimed specifically at the mining industry. The Uniform Standards of Professional Appraisal Practice, the national valuation standards, often must be applied to mineral property valuation, but contains no specific instructions for minerals. The author has campaigned against development of minerals valuation standards proposed by US minerals institutes. Instead he encourages the mining industry worldwide to place its support behind the initiative of the International Valuation Standards Committee (IVSC) to include an extractive industries section in its International Valuation Standards (IVS). This should provide a global set of valuation standards for the mining and petroleum industry within two years. This addition to IVS will provide essential valuation standards reference support for the extractive industries financial reporting standard of the International Accounting Standards Board. The IVS has achieved a high level of acceptance in the developed and lesser developed countries of the world. It provides a comprehensive framework of Generally Accepted Valuation Principles for the valuation profession internationally, for valuation of all property or asset types. IVSC is effectively a sister organisation to IASB. The IASBÆs International Financial Reporting Standards (IFRS), previously known as the International Accounting Standards (IAS), reference and quote IVS in some instructions for determination of fair value. IVSC is a non-governmental organisation (NGO) member of the United Nations and maintains liaison with many important international economic, accounting and financial agencies, such as the OECD, IMF and WTO.

Jan 1, 2002

By Ritter K-C, Sturgul J. R, Filess T

The proposed Lihir open pit gold mine is located on Lihir Island in New Ireland Province, Papua New Guinea. The mine will be located within a volcanic caldera, part of which forms the adjacent Luise Harbour. Kennecott Corporation started engineering design work in 1988 and ended in 1993 when a Feasibility Report was submitted to the Papua New Guinea government by RTZ/Kennecott. The project will be managed by the Lihir Management Company. The mining operation will produce approximately 350 Mt of waste and 62 Mt of low-grade ore over the life of open pit mining. Landforms and traditional land use by Lihirians preclude storing mine waste and some of the low-grade ore on land close to the mine site. The mine waste will be composed of hard rock and soft soild like material which cannot be safely used to construct large land waste repositories by truck dumping. Submarine disposal by bottom discharging barges is the only safe disposal method. The barges will also be required to construct a waste platform along the shore for stockpiling low-grade ore. A simulation model of the waste handling system was written in GPSS/H¦ to assist engineers in selecting the optimum size and quantity of barges and loading docks by analysing the interaction between excavators, trucks and barges. The simulation model was written in enough details to model the various functions that will be encountered during mining. Input parameters allowed for variations in the size and number of trucks, shovels, barges and loading docks. Variations in loading, hauling, and dumping times were from user specified distributions. In order to visualise the interaction between the components of the waste mining operation, the simulation was animated using Proof AnimationT""'. It is believed that this is the first application of an animated simulation study for a mine still in the planning stages.

Jan 1, 1995

Mathematical modelling of continuous rotary vacuum filtration has been limited by the wide range of variables and the absence of connecting equations linking the variables. The filter type and size, mechanical design and predicted performance are generally determined by laboratory leaf tests on representative samples of slurry, or plant samples from an operating filter. A model has been developed which includes the major process variables such as slurry feed rate and concentration, cake thickness, wash water and air flow rates, to predict the filter production throughput, cake moisture and residual solubles. Where possible the model incorporates well established equations relating form filtration, washing and drying rates of the filter cake. Where an equation has not been formulated, standard curve fitting programs have been used to establish an algorithm. The theoretical equations and the derived algorithms are defined in the text. A major feature of the model is that operators, metallurgists, process, mechanical and instrumentation engineers become more aware of the interaction of process variables, the principles of the equipment design and its limitations when operating at peak performance. The model has specific application in the alumina industry where a high moisture content of the filter cake can increase chemical losses and energy costs, and in the coal industry where overseas companies are insisting on lower export coal moistures.

Jan 1, 1989

The nickel ores mined in New Caledonia for one century are mainly silicate ores. These ores are nickel enriched saprolites, formed by partial weathering of peridotites (predominantly harzburgites and some dunites), serpentinised to varying degrees. Saprolites constitute the lower horizon of lateritic soils, sometimes up to 100 metres thick, developed on peneplains now greatly modified by erosion. Saprolites are generally overlain by laterites, a more weathered horizon, where the main components are iron oxy-hydroxides with a low nickel grade. The structure of saprolites depends essentially on the serpentine content of peridotites and, on the other hand, serpentine minerals may have a high nickel content and, so, represent important nickel bearing minerals in silicate ores. Two types of serpentines can be found in nickel ores from New Caledonia: ò primary serpentines, formed by hydration of olivine at temperatures below 400¦C, during overthrusting of peridotites in late-Eocene (Paris, Andreieff and Coudray, 1979), are generally very abundant; ò secondary nickeliferous serpentines, associated with other sheet silicates in garnierites, are now relatively scarce but garnierites were selectively mined one century ago, because of their high nickel grade.

Jan 1, 1996

Published information on technical and market developments in the uses of zinc tends to dwell very largely on two groups of uses of zinc - zinc coatings (mainly galvanising) and zinc casting alloys. These two groups account for two-thirds of primary zinc consumption. However, if total zinc consumption is taken into consideration, coatings and casting account for a little over half the total. Either way, the health - or otherwise - of these 'other' uses of zinc can have a substantial effect on the industry as a whole. The aim of this paper is to put the whole market picture for zinc into better focus, concentrating on the factors which can affect consumption in the 'other half' of zinc's markets: ò brass - the third most important market for zinc at around one million tonnes - responds to changes in the economic cycle. It has seen substantial changes in the balance between different forms of semi products, and, in Europe at least, some real market gains; ò zinc sheet - one of the original uses of zinc in Europe - has grown substantially in some countries, but remains almost unknown elsewhere; and ò zinc pigments and compounds are so numerous that - barring the substitution of zinc oxide in rubber - major overall changes in the market are unlikely. The paper examines these markets and assesses their potential and implications for zinc markets as a whole.

Jan 1, 1993

Nickel ores from three different mines, Digger Rocks, Cosmic Boy and Flying Fox, are treated at the Forrestania concentration plant. The ore types vary from oxidised supergene ores to primary pyrrhotite+pentlandite ores. Mineralogical investigations on the ore and process samples have been carried out in different stages of process development. One of the studies was done with the samples collected from the flotation circuit in 19 June 1994 when the Cosmic Boy ore was processed. The process products were screened, and the size fractions were analysed for the main elements by appropriate analytical methods. Mineralogy of the products was studied microscopically and composition of the sulphides was analysed with an electron microprobe. Liberation of the main sulphides in the flotation feed was determined with the point-counting method, and weight percentages of the minerals were calculated using chemical and mineralogical data. The typical sulphide assemblage of the Cosmic Boy ore is violarite, pentlandite, pyrite, pyrrhotite and chalcopyrite. Violarite dominates over pentlandite (ratio being 70 per cent to 30 per cent), and pyrrhotite is strongly replaced with pyrite and magnetite. One of the most common mineralogical features of this ore type is secondary magnetite, which occurs as narrow rims in porous violarite or in association with secondary pyrite. Serpentine, talc and chlorite are the main gangue minerals. In the milled feed (76 per cent -74 ¦m) locked particles between nickel and iron sulphides are common. About 41 per cent of total pentlandite occurs as pure liberated particles, and 33 per cent as locked grains with violarite. Liberation degree of violarite is 55 per cent, and the most common type of locked particles is violarite+magnetite, carrying about 20 per cent of total violarite. To achieve a recovery of 80 per cent for pentlandite, all the particles containing at least 50 vol-% pentlandite should be floated into the nickel concentrate. Correspondingly recovery of 80 per cent can be reached for violarite if all the particles containing at least 65 vol-% violarite are floated.

Jan 1, 1996

By Schofield N. A

The cross-sectional method of stope grade estimation at Cobar Mines has consistently had several shoneomings, me most imponant of which being mat stope grade is significantly overestimated in the high grade lenses.The use of mree-dimensional ore lens modelling improved the grade estimation and ore waste definition but significant overestimation still occurred in me high grade stopes, particularly those wim extremely variable grade distribution. The implementation of an indicalor kriging based method for mapping of me high grade copper mineralization has significantly improved the quality of copper grade estimates and provides a mineralisation geometry similar to that generated manually by me mine geologists. This paper presents the results of a test case study in the application of indicator kriging to the mapping of the copper grade in two stopes in the QTS North mineralisation. The results are encouraging in that they prov ide coofi rmation of the geometrical model developed by the geologists and much improved estimates of the grades of me stopes whencompared to me grade reponed from mining these stopes.

Jan 1, 1993

By Lyman G. J, Ka

The use of images to determine blast fragmentation is the only feasible technique when one does not want to disturb the production cycle. However, three major problems exist with the use of images. The first is determining real size from a two-dimensional particle, the second is estimating the fines which are missing due to image resolution and particle size range, and the third is proper sampling such that a statistical probability can be calculated for the distribution. Once these problems are resolved, the tedious process of digitizing images by hand may be automated. This paper describes the present techniques used at the JKMRC to "size" blast fragmentation, estimate the missing fines using the Rosin-Rammler equation, determine the sampling error using Gy's sampling equations, and extract the particles from an image using an IBM-AT computer.

Jan 1, 1990

The discovery of economic uranium miner alisation in unique geological conditions at Yeelirrie, 700 km NNE of Perth, presented Western Mining Corporation Limited with a num- ber of sampling and evaluation problems. Carn- otite mineralisation occurred in a porous cal- crete-clay lithology in close proximity to the water table; background information on such a deposit was non-existent and sampling in these conditions could be difficult. The deposit was sampled initially by aug- er drilling with X-ray fluorescence analysis of drill cuttings, followed by reverse circulation and diamond drilling with analyses by X-ray fluorescence and gamma logging of the holes. Two costeans provided lithological and grade distribution data and mining experience in the deposit. Spoil from the costeans was stockpiled according to location in the first costean and according to location and grade in the second costean. Samples from the various stockpiles were analysed by X-ray fluorescence. No. 1 costean was extensively sampled by channel sampling of the walls and by pit sampling of the floor of the benches of the costean by back hoe. No. 2 costean was sampled by Geiger counters mounted in T-probes and by the gamma logging of auger holes to establish the valid- ity of the T-probe results. Samples were taken

Jan 1, 1976

Mining companies often view water quality as an environmental issue. The importance of water quality as a production related issue in mineral beneficiation is greatly underestimated at many mineral processing operations. While most mine sites have comprehensive water balance data for water quantity, the information regarding the quality of water supplies available on site is limited, inadequate or non-existent. The seasonal variations in process water quality and changes in the composition of various water streams are not known. Despite the fact that water represents about 80 to 90 per cent of the volume of mineral pulp processed in a flotation plant, the influence of process water composition on flotation performance is often poorly understood. The process water used at mineral processing operations is made up from a number of available water sources, which can be classified as recycled water streams or make-up waters. The recycled water streams are commonly the tailings and concentrate thickener overflows, filtrate from the concentrate filtration plant and tailings dam return water. Make-up waters can originate from a variety of sources: surface waters (rivers, lakes, reservoirs, dams), groundwater (wells and springs), mains water (potable water), treated and untreated sewage waters and industrial effluents. Mineral processing plants are increasingly recycling water to reduce demand for fresh water and minimise the discharge of wastewater to the environment. However, increasing water recycling can have adverse effects on process water quality and ultimately on the performance of mineral separation processes. The main reasons for reduced plant performance due to water recycling are the accumulation of organic and inorganic compounds in the process water and increased microbiological activities. Other detrimental effects of water recycling can be increased reagent consumption and inefficient dewatering of tailings and concentrates. Recycling of water also tends to accumulate very fine suspended particles. Excessive amounts of slimes in the process water can also have an adverse effect on mineral beneficiation processes. The main constituents of process water are dissolved gases (oxygen, nitrogen, carbon dioxide), colloidal and suspended solids of inorganic and organic nature (including micro-organisms: dead or alive), dissolved organics (natural organic matter, residual reagents, reaction and decomposition by-products of chemical reagents, impurities in the reagents and metabolites originating from microbiological activities) and inorganic compounds (acids, alkalis, inorganic salts, metal ions, anions and heavy metals). Inputs to the chemical composition of process waters are: dissolution of soluble mineral phases present in the ore, surface oxidation followed by dissolution of mineral particles during grinding and mineral processing, the chemical composition of various make-up waters and recycled water streams, and reagent additions during mineral processing. The beneficial or detrimental impact of process water quality on flotation performance can be attributed to a number of subprocesses: adsorption and/or precipitation of inorganic and organic species present in the process water onto the surface of mineral particles, chemical reactions between process water constituents and the chemical species present on the surface of mineral particles and interactions between the chemical and microbiological species present in the process water and the various reagent species added in solution during mineral processing. Dissolved chemical species such as calcium, magnesium, iron, copper, lead, zinc, nickel, sulfates, phosphates and carbonates can have a strong effect on the electrokinetic properties of oxide and sulfide minerals, at certain pH ranges. Several reactions can occur at the solid-liquid interface that can play an important role in determining surface adsorption of reagents. Solid-liquid interfacial properties of mineral particles can be significantly affected by the conformation of adsorbed and precipitated reagent layers, which in turn are determined by solution chemistry. The chemical and microbiological constituents of process water can have a significant effect on liquid-gas interfacial properties and have a strong influence on froth height, strength and stability during flotation. Water chemistry can play an important role in determining the interactions between minerals present in the ore and the chemical reagents added in the mineral processing plant by altering the reagent-solution and mineral-solution equilibria. These interactions can include dissolution, micellisation and precipitation of reagents, dissolution of minerals contained in the ore followed by hydrolysis, complexation, adsorption and precipitation of dissolved chemical species and reactions between dissolved ions and various reagent species present in solution. All of the above mentioned subprocesses can ultimately have a significant effect on the efficiency of mineral processing operations. In this presentation, a systematic approach for assessing the composition of water supplies available at the mine sites and for investigating the influence of process water quality on the efficiency of mineral processing operations will be discussed. The consequences of mixing different quality water streams to produce the required volumes of process water for some flotation plants will be highlighted. To substantiate the water quality issues described in this paper some examples are given from a metalliferous processing perspective. However, the topics described in the paper are not only relevant to metalliferous processing but to all other type of mineral processing operations as well. In fact the principles described in this paper have also been successfully applied to the coal flotation industry.

Jan 1, 2006

Batterham and Algie began their paper on: `The role of technology in the minerals industry' (1995) by noting that while: it is often stated that innovation is central to the economic survival of mining and minerals processing in the face of global competition, .. . technology is often far from a core strategy in our industry. This point is correct. Throughout the world, as a broad generalisation, mining companies do not value technology development as a principal means of gaining competitive advantage. It is important to understand why this is the case. Batterham and Algie address this question by making distinctions between innovation, technology and research. They note that while: all successful (mining) companies are good at innovation . . . that innovation can proceed without any research and development and that it is innovation that generates the competitive advantage, not research and development per se. In this paper we accept these arguments. However, our focus is somewhat different. Whereas Batterham and Algie took a mining company's perspective on the technologies of mining and processing, we take a broader view of the opportunities for technology development for company Australia but, in order to focus the argument, we restrict our discussion to the area of mining (rather than processing); we focus particularly on mining systems and mining equipment. We begin by looking at the motivation of companies operating in any industrial sector to invest in research and development. Figure 1 recognises four levels of industrial maturity. For companies in the embryonic and growth stages R&D often is essential to initiating and developing the business. Mining, on the other hand, is a mature industry. In mature industries the conventional roles for R&D are to reduce costs, to extend product differentiation, or to develop new technology with the aim of rejuvenating the business. Next we ask whether these general-industry arguments apply to the mining industry. If they do then the mining industry should value R&D more highly; after all cost reductions and business rejuvenation are goals that are worth achieving. On the other hand if, for whatever reason, these general arguments do not apply to mining then this may lead the mining industry to invest only modestly, or not at all, in R&D. In this event, while this may be a rational decision for the mining industry, it may not be in the best interest of a nation like Australia where revenues from the sale of mineral products represent an important part of the country's economy.

Jan 1, 1997

The New Guinea Mobile Belt is the northern zone of the Melanesian Orogeny (Dow and Sukamto, 1984), which consists of a complex zone ofupthrusted and accreted, regionally metamorphosed geosynclinal sediments and volcanics of Mesozoic to Eocene age and the overlying sediments. On the northern margin of this accreted terrane, formed an Eocene to Middle Miocene island arc. The North New Guinea Basin formed during the Upper Oligocene on the accreted margin. The depositional history of this basin is complicated by major crustal movements during the Upper Miocene to Holocene. During the Middle to Upper Miocene two magmatic arcs were emplaced. The northern magmatic arc is in part, spatically and genetically related to the Eocene to Middle Miocene island arc. The Maramuni-Utawa Magmatic Arc (southern) is a result of the Oligocene accretion and regional metamorphism. Coincident witt these magmatic arcs are belts of mineralization containing porphyry Cu-Au, epithermal/hydrothermal Au, Ag + Cu-Pb-Zn, exhalative Cu-Pb-Zn + Ag-Au, lateritic Ni-Cr-Co + PGE and alluvial Au, PGE, Cr occurrences and deposits. An intergrated tectonic model is presented for these and other data for the northern zone of the Melanesian Orogeny.

Jan 1, 1990

The Mesozoic intrusive rocks in southeastern coastal China can be divided into three intrusive suites, and they can be brought into corresponding with four cycles of volcanic activity. This paper describes their time-space relation with volcanic rocks, and their geochemical characteristics. Data from the Mesozoic volcanic-intrusive. complex rocks in Eastern Zheijiang, Eastern Fujiang and Eastern Guangdong show distinct regional differences, both within and tectonomagmatic activity regions. The southeastern coast of China involves four tectonomagmatic activity regions. They have many differences on the nature of magma source regions, activity patterns of magma, time-space distribution, petrography and petrographic facies association of volcanic and intrusive rock and mineralization.

Jan 1, 1990