Search Documents

By N TassT, J Cyr

At the East Sullivan site, wood wastes covering the abandoned mine tailings impoundment prevent sulfide oxidation by creating an anoxic environment. The addition of coarse ligneous wastes and their high permeability favour infiltration, resulting in a water table rise that maintains most tailings under water saturation and thus provides an additional protection against sulfide oxidation. Moreover, high infiltration allows a more rapid flushing of acid prone groundwater generated prior to the cover placement, which could cause acid mine drainage over a long period of time. Finally, the pore-waters under the cover are characterised by a strong reducing potential, high alkalinity, and near neutral pHs. These conditions favour sulfate reduction and base metal precipitation as sulfides and as carbonates. Pore-water composition monitored from 1992 to 1998 showed a significant Fe2+ decrease, following cover placement. Thereafter, the restoration strategy capitalised on the alkaline and reductive properties of the waters underlying the wood-waste cover. An original treatment of acid effluents, based on the recirculation of water discharging around the impoundment through the organic cover, was implemented. In 2002, the recirculated water from May to October had a mean pumping rate of 240 m3/h, for a total volume of 800 000 m3. Data gathered near the dispersal zone from 2000 to 2002 show that despite the recirculation of acid water (pH ÿ3), the pH decreases by only one unit from 7 to 6, during the recirculation period, ie from May to November. However, alkalinity decreases from 800 to 100 mg/L-CaCO3. Despite this decrease, the alkalinity is back up to 800 mg/L-CaCO3 the following May, thanks to sulfate reduction. From 2000 to 2002, Fe2+ concentration in the pore waters near the dispersal zone is maintained below 2 mg/L. Evolution of surface water quality suggests that the contaminated groundwater flush is completed in the north and north-west area of the impoundment; the east sector is under recovery, while the south sector remains the most problematic. A wood-waste cover, besides limiting sulfide oxidation, can fill the role of alkaline reducing barrier for the treatment of these acidogenic waters, until a balance between acidity and alkalinity in the effluent is reached.

Jan 1, 2003

By M Dunglison, P M. Cameron

Simultaneous mass-balancing of a mineral processing flow sheet results in adjustments to each data point that reflects the accuracy and precision across the full set of data. In this way, all the good work that goes into designing the sampling and analysis protocol for each sample point is leveraged in order to produce a æbetterÆ set of balanced numbers for every sample point in the circuit. Few operating plants employ whole of circuit balancing techniques to produce reported operating results. This situation is changing with the application of mass balancing technology which utilises redundant data for production accounting and metal reconciliation from product to ore source across multiple phases and multiple time periods. Mine and plant data can now generate credible information to improve productivity. Mine and plant personnel can now use consistent data sets for review and planning. Decisions based on balanced data can be made quicker and with increased confidence.

Jan 1, 2005

By Wyborn L. A I, Idnurm M, Hinman M. C

Comparison of the Proterozoic Apparent Polar Wander Path (APWP) for Australia with the corresponding geology of northern Australia suggests that a number of discrete interplate tectonic events, manifested on the APWP as bends or inflections, may have controlled sedimentary basin evolution, ore fluid production and the timing of mineralisation. Similar features in the Phanerozoic APWP for the North American plate appear to correlate with major orogenic events, basin deformation, movement and 'entrapment' of hydrocarbons and minerals. Interplate tectonic events cause intraplate deformation which in turn controls the subsidence/uplift and sedimentation histories of the basins. Interplate events are thus responsible for creating, deforming and destroying sedimentary basins and the associated petroleum and mineral systems. The basins of northern Australia show remarkable similarities in the successions of volcanic and sedimentary deposits. Unconforrnities of regional or sometimes only local extent have been mapped between the major sedimentary sequences and it is predicted that interplate tectonic events corresponding to bends or inflections on the APWP directly reflect the processes that have produced these widespread unconformities. These processes are also likely to have controlled the geometry and character of the fluid migration pathways and hence the mineralising events. Palaeomagnetic studies of Proterozoic rocks in sedimentary basins provide a tool for predicting the timing of regional mineralisation events, particularly for low-temperature mineral systems. The techniques, when coupled with systematic regional basin analysis, using petroleum exploration techniques, may identify a number of new mineral 'plays' in northern Australia. Prominent inflections in the APWP occur at approximately 1700, 1670, 1650, 1600, 1540, and 1480 Ma. Each of these may be related to a regional compressional deformation, important mineralising event, or significant change in style and type of sedimentation. Most appear to be associated with magnetic overprints. Some of the inflections between 1400 and 540 Ma may also mark significant events in the evolution of Meso- and Neoproterozoic basins. Further work is required to correlate inflections in the APWP with alteration events in order to understand their regional significance.

Jan 1, 1994

By Das A. K

Investigations were carried out to understand the effect of liquid viscosity (u = 1 x 10-3 - 5 x 10-' Ns/m2) on the size of primary bubbles formed at high gas injection rates (Q = 100 - 1000 cc/s, U = 0.04 - 0.42 mach) under room temperature conditions using flush tuyere (3 mm diameter) operating vertically upward. Tuyere pressure fluctuations were correlated to the mode of bubble formation by simultaneously filming the bubble and the corresponding tuyere pressure fluctuations displayed on an oscilloscope screen. A simple mathematical treatment is presented to estimate bubble size in viscous liquids. The theoretical results are compared with the experimental measurements.

Jan 1, 1987

In June 1996, Nord Resources Pacific (Nord) decided to work towards obtaining all necessary approvals from the government of PNG for a mine on Simberi Island in the Tabar Island Group, New Ireland Province. On the 9th of September 1996, Nord submitted a Proposal for Development and an application for a Mining Lease to mine the oxide gold deposits on Simberi Island. The Mining Lease was granted on the 3rd of December 1996 in a signing ceremony on Simberi Island. This was achieved in the extremely short time frame of less than 3 months and this paper attempts to explain the processes which made it possible.

Jan 1, 1997

Sophisticated pit optimisation software has allowed mine planning engineers to generate mining outlines that consider the numerous factors that have a major effect on the success or otherwise of a mine plan. The outlines are generally generated using a range of values for which one can assume a fixed mining cost and a variable revenue. During analysis, the expected costs and revenues are used to investigate the cashflow and sensitivities. Ultimately, the final pit and incremental outlines, or shells, are selected for a given expected price. This paper proposes an alternative method for incremental pit shell selection that considers the risk the mine be prepared to accept. The life of mine is divided into a number of Business Risk Periods (BRPs). The BRP represents the period of time over which the owner is prepared to invest capital. During each BRP, the mine will then operate at a selected investment cost which is generally equal to or greater than the minimum required to meet production targets. In this way, a robust mine plan can be produced which allows the mine to react to change without having to alter the incremental shell limits while maintaining a strategic risk profile. This paper will summarise factors to be considered in selection of the BRP and the incremental pit shells within the BRP.

Jan 1, 1998

By A C. Robertson

Over the past decade there has been continual change in the way that mines have been managed and the component roles of those people who make up the total mine management system. Major issues have included the change in the business structure of mining companies, the change in on-site infrastructure, increased personal liability of managers for the safety and health of employees and increasing social and environmental pressures on managers and their staff. This paper looks at the changing roles of two of the many groups of professionals associated with the mining industry - the equipment supplier and the mining consultant. The profiles of the ACME Group Pty Ltd, suppliers of ventilation equipment and ancillary canvas and plastic products to the mining and construction industry, and Tennent, Isokangas Pty Ltd, Consulting Mining Engineers, are presented.

Jan 1, 1998

During the 1998/99 Asian crisis Solid Energy's export revenues collapsed from over US$70M to under US$40M. Simultaneously, domestic market uncertainty led to decreases in volumes and prices. A major new underground mine was not technically viable, and was closed, and several other mines were marginal. Less than two years later, Solid Energy and its JV partner closed a second new underground mine. The company was in financial crisis, and reported an $86M loss for 1998/99. After refinancing with stringent workout conditions it still had minimal returns due to low prices, unaffordable transportation costs and huge unrealised FX losses as the NZ dollar fell 40 per cent in value. The obvious scenario was to æcash upÆ û complete extraction at remaining mines, sell off any viable parts of the business, pay off debt and wind the company down.In 2002 Solid Energy has completed its recovery. Although margins remain slim and volatile in both export and domestic markets, it is achieving record volumes and revenues. It has paid off its shareholder loan, has minimal remaining FX losses, and cashflow is allowing further mine and infrastructure development. The key to the turnaround has been implementation of rigorous planning, analysis and decision-making in all aspects of the business. The company has a comprehensive, rolling 20-year plan used annually to update rolling five year and annual business plans. Solid Energy augments strong line management operations with rigorous standards and processes for mine planning and development, operational decision-making, and functional support. Detailed, quantitative risk analysis is used in all aspects of the business and allows comprehensive integration of opportunity and risk management across all activities in the company.Coal mining is widely perceived as an æold-economyÆ industry. But, like other successful æold economyÆ companies, the information systems and management processes used by Solid Energy are as leading edge as any in the high-tech sector. They are the key to managing to add and sustain maximum value for a company that has access to coal resources sufficient for hundreds of years.

Jan 1, 2002

The Broken Hill Proprietary Company Limited (BHP) started as a silver-lead-zinc mining company in Broken Hill, New South Wales, Australia in the 1880s. Since then it has diversified into the resource industries of steel, iron ore, coal, petroleum and copper. BHP World Minerals is a Business Group of BHP which is one of the worldÆs largest and most diverse mineral resource enterprises. BHP supplies raw materials for steelmaking, copper concentrate and other mineral commodities to customers in more than 45 countries. BHP World Minerals has operations spread throughout the world û in Australia, the United States, Brazil, Zimbabwe and Canada. Commodities produced by BHP World Minerals currently include silver, lead, zinc, titanium minerals, platinum group metals and coal. The BHP World Minerals Cannington silver-lead-zinc mine in Queensland, Australia is a return to the cradle of BHPÆs early silver-lead-zinc years. This paper compares the success factors and challenges at Broken Hill and Cannington.

Jan 1, 1998

By M Hedley

Tracking plant and personnel in mining operations provides multiple potential benefits for a mine including improved safety, better monitoring of production, traffic control and, in the future, monitoring and control of autonomous vehicles. The main techniques currently proposed and used for wireless tracking are radio frequency identification (RFID), signal strength based techniques and time of arrival (TOA) based techniques. RFID provide poor accuracy in the complex radio propagation environment present in mines and does not provide continuous tracking and signal strength techniques. TOA based techniques are potentially the most accurate, however, most current equipment has not realised the potential of the technique. CSIRO has been developing the Wireless Ad hoc System for Positioning (WASP) system for wireless tracking in a range of challenging environments including underground mines and surface operations, where GPS reception is compromised by depth. The system utilises a number of ‘anchor nodes’ that are placed at fixed and known locations within the mine and tags attached to the plant or personnel to be tracked. The system provides an ad hoc data communication network, thus, wired data connections are not required to the anchor nodes. WASP uses transmissions in the 5.8 GHz ISM (instrumentation, scientific and medical) frequency spectrum to perform highly accurate ranging between nodes, hence tracking of tags. The localisation performance of the system depends upon the radio propagation environment, ranging down to 0.1 m in low multipath conditions. In this paper we describe the WASP system and provide results of testing in underground and surface operations showing the system achieving high ranging, hence localisation, accuracy.

Nov 22, 2011

Government established and financed the NZ Steel Investigating Co in 1960. Its investigations showed that a steel industry was feasible and desirable based uponNorth Island titanomagnetite ironsands, and charted a route for its establishment. The initial processing used post-1945 preheating and prereduction developments, but later innovative improvements created what was essentially a new New Zealand technology. Of the North Island titanomagnetite deposits: the small ones at Waipipi were best made available for export; those at Kawhia and Taharoa were too remote for the economic siting of a mill; that at Raglan proved too small; while at Waikato North Head three times the requirement of 50 million tons of concentrate were located in two sand areas averaging 18 per cent titanomagnetite. Economic studies showed that a South Auckland site would be ideal, close to New Zealand's biggest market. The mill site, on a basalt flow at Glenbrook, was located by a half-day's fieldwork - near both the Waikato North Head deposit, and a railhead for bringing in Waikato coal, etc, and taking out steel products.   This development was one of several since World War II which altered significantly the lives and homes of New Zealanders (others were natural gas, oil, geothermal power, epithermal gold, aluminium, opencastable lignite, etc). All had the essential ingredients of the highest government backing, direct or indirect government finance, and first-class New Zealand scientific and engineering skills (eg to create new technologies). Not one such project failed.

Jan 1, 1993

Remote sensing techniques can be used to map joint sets in a rock mass for the estimation of in situ block size distribution and improved optimisation of blasting. This paper reviews remote sensing using photogrammetry and laser mapping for mapping rock masses and presents elements of the analyses applied to data acquired with these mapping technologies. These techniques enable a user to map areas of hundreds of square metres rapidly with high precision. Using this data computer programs such as Sirojoint can provide estimates of joint position and orientation with orientation measurement accuracies better than one degree. The paper describes the use of remote mapping and provides potential users with a description of some of the advantages and limitations of the mapping techniques and the data they produce. Mapping of lithology and structure of rock masses is an important task required in many areas of mining and construction. It is a complex task routinely performed using established techniques developed to provide consistent results under a wide range of conditions. The techniques for data acquisition and analysis described in this paper enable more accurate mapping to be performed rapidly and enable mapping of inaccessible sections of a rock mass. These techniques will provide geologists and geotechnical engineers with more detailed, accurate data than previously available.

Jan 1, 2001

By M R. Davidson, M P. Schwarz

A model for column bioleaching is investigated to identify and understand aspects of bacteria in bioleaching applications, which have implications in heap bioleaching operations. The model is used to simulate scenarios that would otherwise be time consuming to perform experimentally. This study uses a model of bacterial transport and attachment/detachment to ore particles, with a bioleaching model for the depletion of a copper-sulfide, also accounting for liquid and gas flow and gas/liquid oxygen mass transfer. The model includes aspects such as oxygen and ferrous ion consumption, coupled with leaching of a copper-sulfide via the shrinking core model. The model is used to investigate how the rate of leaching is affected by the bacterial concentration in the columns, by the bacterial regeneration of the leaching oxidant ferric ions. The model is also used to assess the impact of oxygen limitation and inoculation method on the copper leaching. Some comparison of the model with experimental data will be shown.

Jan 1, 2004

By D Kubik, K The

The New Zealand (NZ) Transport Agency’s Waterview Connection will complete Auckland’s Western Ring Route, a 47 km north–south motorway alternative to Stage Highway 1. The project is being delivered by the Well-Connected Alliance comprising the New Zealand Transport Agency (NZTA), Fletcher Construction, McConnell Dowell Constructors, Obayashi Corporation, Parsons Brinckerhoff NZ, Beca Infrastructure and Tonkin & Taylor.The project involves construction of 5 km of new motorway, nearly half of it underground connecting State Highway 20 (SH20) to State Highway 16 (SH16). The underground portion of the project incorporates twin 13.2 m inside diameter (ID) tunnels 2.4 km long, each carrying three traffic lanes, one for north-bound traffic and one for south-bound traffic. The tunnels are being driven by a 14.46 m outside diameter (OD) 2400 t, tunnel boring machine (TBM) shield that was assembled and launched at the southern portal. It will be turned and re-launched at the northern portal for the return drive to the southern portal where it will be disassembled. This paper presents two major temporary works elements contributing to the successful launch of the TBM: the TBM assembly crane platform and the TBM shove frame and associated components.Tunnel boring machine shield assembly – crane platformThe TBM shield was delivered to site in subassemblies ranging in weight from 100 to 380 t. It was initially proposed to use a 750 t crawler crane sitting above the tunnel portal headwall to assemble and disassemble the TBM. However, this did not have sufficient capacity to allow the TBM shield to advance clear of the tunnel before disassembly commences. To reduce the crane’s working radius a temporary steel crane platform was developed that is supported on the side walls of the tunnel approach trench. This has enabled a smaller, less expensive, 600 t crawler crane to be used and will allow the TBM shield to clear the tunnel before disassembly.Tunnel boring machine launch – temporary worksTo launch the TBM a purpose built steel frame was required for the TBM thrust rams to react against. The shove frame had to be able to transfer the thrust loads from the TBM shield to the ground below and thrust wall behind. A range of potential thrust loads and jacking patterns were examined to develop the design load cases for the shove frame. The shove frame was used to launch the TBM at the southern portal and to re-launch it at the northern portal. Elements of the shove frame will also be used to support the portal faces during the TBM arrivals.CITATION:Kubik, D and The, K, 2014. Waterview Connection – temporary works for tunnel boring machine?launching, in Proceedings 15th Australasian Tunnelling Conference 2014, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

Kalgoorlie Consolidated Gold Mines Pty Ltd is currently developing the 'Super Pit' gold mine in the mining area known as the Golden Mile adjacent to the city of KalgoorlieBoulder, Western Australia. The presence of numerous abandoned mine workings and complex structural geology has required considerable geotechnical input into the determination of the optimum pit slope geometries for both interim and ultimate pit slopes. Slope design is based on detailed site investigation and stability analysis which is balanced with historical operational experience. This paper discusses the process of determining the optimum pit slope angles for each of the stages of the west wall of the 'Super Pit'. The risks associated with slope instability are discussed for each stage.

Jan 1, 1994

By S S. Kanchibotla, S Morrell

In recent years there has been a growing recognition of the impact that mining practices have on the efficiency of mineral processing operations. Head grade, dilution, particle size distribution and their variability are known to have a significant effect on the throughput and recovery achieved in mineral processing plants. Improved process monitoring and modelling have provided the opportunity to identify and quantify some of these impacts and to define very significant incentives to optimise the overall operation from the mining face through subsequent comminution and processing. The Julius Kruttschnitt Mineral Research Centre has been undertaking research to optimise æMine to MillÆ performance through a major AMIRA research project and through individual research contracts with mining companies. This work has resulted in a broad range of field and laboratory experience in terms of both the challenges and the opportunities encountered when tailoring blasting operations to suit the overall æMine to MillÆ production chain. This paper describes the objectives of æMine to MillÆ blasting to optimise the system of rock breakage involved in the blasting, crushing and SAG milling of hard, brittle ores. The design of such blasts falls outside the conventional envelope of experience for most engineers and requires the consideration of some critical factors if the objectives of such blast are to be met and some of the potential problems are to be avoided. Experience to-date has also found that the quality of implementation is critical to the success of æMine to MillÆ blasts.

Jan 1, 1999

By Holcombe R. J, Dobos S. K, Little T. R

Blue amphibole-bearing rocks in the North D'aguilar Block of southeast Queensland occur either as relict pods and lenses within regionally extensive greenschist facies phyllites and schists or as blocks entrained in serpentinite-matrix melange. Epidote + crossite-bearing varieties predominate and formed under conditions consistent with underplating and high P:T metamorphism in a subduction-related tectonic environment. Neither lawsonite nor jadeite has been observed and metamorphic conditions are estimated at 380-4500C for pressures of 0.5-0.8 GPa. High P:T metamorphism occurred during the earliest stages of deformation and was superimposed upon protoliths of inferred Late Devonian - Early Carboniferous age, including mafic volcanics, tuffs and coarse volcaniclastic breccias as well as pelagic and henipelagic sediments, all of which have undergone varying degrees of over-printing to the greenschist facies. Greenschist facies metamorphism occurred during the second phase of deformation and was associated with the formation of mainly flat-lying or subhorizontal structures; it followed the cessation of subduction and occurred in response to either thermal relaxation during uplift or the imposition of regional heating induced by crustal thickening and/or synkinanatic granite emplacement. Uplift and cooling of the high P:T rocks was completed by 260-265 Ma and may have occurred in response to the same extensional processes which gave rise to the onset of rifting in the adjacent Esk Trough.

Jan 1, 1990

By E Yurakov, D J. Ashelford, M I. Slate

The push for increasing coal production rates continues to place increasing demands on mine management to safely and effectively control seam gas. Gas drainage strategies applied vary in both effectiveness and form. Methods employed are a function of assessed risk, gas reservoir characteristics, surface and underground access, budgetary constraints and gas utilisation potential. With the aim of establishing and optimising the effectiveness and efficiency of gas drainage systems, Australian coal miners in cooperation with gas management specialists are embracing the use of gas reservoir simulators and gas emission models. This paper discusses the evolution of gas drainage practices in Australian underground coal mines and the role of gas reservoir assessment methods in optimising gas drainage systems and gas production forecasts.

Jan 1, 2005

By T Gready

Stawell Gold Mines operates the Magdala underground mine in western Victoria, Australia. Several orebodies are extracted by longhole open stoping at a depth of 900 m below the town of Stawell. Some stopes are backfilled with cemented slurry rock fill (CSRF) to ensure stability, increase recovery of ore reserves, minimise dilution of ore grades, and add value to the project. StawellÆs simple CSRF system is described, including the novel equipment used to minimise capital costs. Design criteria, operating procedures, monitoring systems and results are discussed in detail. Practical aspects are considered, including lessons learnt about barricades, overbreak and segregation. The economics of CSRF are discussed, including capital costs, operating costs and the total cost per ounce of gold poured. Options for mining with and without CSRF are compared in terms of return on investment and net cash flows. Examples demonstrate the method used to calculate æbreak-evenÆ stope ore grades which determine whether or not CSRF will add value in different circumstances.

Jan 1, 2002

By R Steinhaus, D M. Frantois-Bongarton, P W. Cleary, G K. Robinson, M D. Sinnott

Multotec Process Equipment and Dominique Frantois-Bongarton have a patent for a mineral sampling device, which they call a æTrue-Belt SamplerÆ. This uses a plough, which is rotated about an axis parallel to a conveyor belt to throw material off the belt. A fixed sample cutter takes a sample from the material thrown off the belt.Discrete element modelling has been used to consider a range of plough designs, plough speeds, positions for the cutter relative to the plough, cutter apertures, cutter designs and frictional properties, prior to the building of a physical prototype. This modelling work will be discussed, both as an illustration of the role of modelling in the development of new materials-handling devices and in order to explain the likely strengths and weaknesses of this new type of sampling device.CITATION:Robinson, G K, Sinnott, M D, Cleary, P W, Steinhaus, R and Frantois-Bongarton, D M, 2012. Modelling of a ætrue-belt samplerÆ - A new device for sampling from a conveyor belt, in Proceedings Sampling 2012 , pp 33-40 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012