Search Documents

The extent of regional stratigraphic and structural geological mapping so far carried out in Australia is likely to be greatly overestimated by uncritical inspection of the latest authoritative geological map of the continent-that so ably compiled by the late Sir'T. W. Edgeworth David. Vast areas geologically coloured on this map are in fact known only from the most meagre field data, some of Which even include observations of distant views from which the so-called "geology" has been indicated in' reconnaissance reports.This applies to large areas in Cape York Peninsula; the plateau of Arnhem Land, and its margins except on the west where the Pine Creek mineral belt is better known; to the Desert Basin of Western Australia, practically the whole of the western half of the Northern Territory, much of east-central Western Australia, and northwestern New South Wales. Other vast areas are, more happily perhaps, left blank. It is true that prospecting parties have, at various times and with varying degrees of thoroughness, traversedparts of these little-known regions, often, however, in the search for gold or the.more obvious types of metalliferous mineral deposits and, furthermore, too often without leaving any written account of their examination, or with very sketchy details supplied. Unpublished geological surveys also cover some parts of these regions, but, on the whole, the picture we can draw of the regional deployment of rock masses in Australia is far less full than even David's map, with its obvious blanks, presents to us.Lest the practical mineral seeker among us should be inclined to place too much reliance on the prospecting to which I have referred.as giving him a straight hint of what country to keep out of, we may point to the recent discovery of a major sedimentary basin in the east KimberllilYs on which Dr. Teichert will have more to say. And that there are new metalliferous mineral deposits to be foundin parts of these little-known areas no one can doubt, for, after all, new discoveries are made from time to time in areas so well-known as the Victorian gold-fields. I take it then that regional geological mapping is a necessary concomitant of the further development of Australia's mineral resources-but I am not of the school that places it first on the list of priorities, and furthermore I believe that there can be a royal road to regional mapping-an inspired approach based on knowledge already gained and led to fruition by field surveys in key areas, by which there may be obtained a result giving a significantly close approach to actuality with only a fraction of the work that would be required for detailed field surveys on a systematic basis. I believe that a policy of rapid reconnaissance of such a type should be adhered to, especially in view of present deficiencies in numbers of geologists available for all purposes in Australia. The details that must eventually be sought can, I believe, be filled in later as the whole country becomes more developed and amenable to detailed surveys.

Jan 1, 1950

At the present time this plant is treating by direct cyanidation 1,000 tons of ore from Open Cut mining and dumps, and 1,200 tons of current flotation tailing obtained from the Sulphide Mill, per day.The following table shows the average analysis of the two feed products (see Table 1):Precipitation Process.-The pregnant solution obtained by the cyanidation of the above has the following general analysis:-Gold 0·600 dwt. per tonTotal Cyanide 0·050 %Free Cyanide 0·045 %Calcium Oxide 0·015 %KCNS 0·060 %Na2S20S 0·140 %CaS04 0·200 %Cu 0·050 %Zn 0·004 0/0K4Fe (CN) 6 NilThis solution, after standard clarification, is precipitated by means of zinc dust and a soluble lead salt.

Jan 1, 1939

By R P. Langford, T A. Moore

Indonesia over the last 15 years has experienced a surge in coal exploration, which has led to the development of a major export industry. This coal exploration has improved the understanding of the geology of the Indonesian coal deposits. The main economic coal deposits are of Eocene and Miocene to Pliocene age, which mainly occur in Kalimantan and Sumatra and were formed from peat deposits in an equatorial paleoclimate similar to that prevailing today. Some of these peats were domed peats, which grew above the normal water tables, under a climate of year-round rainfall; these peats grew above the level at which waterborne mineral matter can enter the system, resulting in low ash and sulphur, and locally very thick coal. It is believed that such peats have formed the unusually thick, low ash, and low sulphur Miocene coals of Indonesia. Coal deposits of Eocene age are typically characterised by thinner seams, with relatively higher contents of ash and sulphur. The Miocene coals and Eocene coals both appear to have formed in lacustrine, coastal plain or deltaic depositional environments, similar to the modern peat-forming environments of eastern Sumatra and parts of Kalimantan. The Eocene coals formed mainly in extensional tectonic settings. Miocene - Pliocene coal deposits formed in a range of tectonic settings; the most significant, for large economic coal deposits, are the foreland basin setting of the large Neogene coal deposits of South Sumatra.

Jan 1, 1999

Digital Simulation of Particulate Processes The inherent complexity of mineral particulates (shape, size and mineralogical texture) has challenged conventional simulation model approaches for decades. Much effort was expedited in using mathematical assumptions to accommodate stereological effect. With the advance of instrumental methods such as x-ray microtomography 3D structure can, in many cases, be measured directly. The information derived from such measurements provides direct input to building the structural digital model. In addition digital simulation methods that enable creation of process realistic particulate properties in an efficient digital computer space have demonstrated their effectiveness to model a variety of realistic packing, sorting and multi-phase processes. The paper reviews recent advances in the use of information derived from 3D micro-tomographic imaging and laser scanning technology can be coupled with digital methods to enable simulation of tablet compaction and dissolution, filtration and permeability, column packing and leaching kinetics, packing and cementation of nuclear waste. By assigning 'properties' to a digital zone (voxel) in the computational space it is possible to mimic the realistic characteristics of quite complex particulate mineral processing systems. The system self-adapts to correct the coherent particle characteristics (shape, size, compound, porosity) with time. Such simulations are useful to elucidate the sensitivity of system performance to variations in process parameters. Dimensional scaling of the approach is also possible, as the case studies will illustrate, in deploying the method to both small (micron) and large (m) features. The use of process realistic simulations presents experimental challenges in code validation. It is in this context that other tomographic methods play a role in direct 3D measurement of system behaviour such as electrical and optical sensors.

Sep 13, 2010

By H Firdausi, I Pasek, T Chenier

The Grasberg Block Cave (GBC) Mine is one of the future underground mines of PT Freeport Indonesia (PTFI). Located in the remote highlands of Papua, Indonesia, the GBC mine is scheduled to start production in 2017 reaching its peak production capacity of 160 000 t/d in 2023.In order to reach planned production capacity, the GBC mine will utilise an ore handling system consisting of rail haulage, crushing and conveying. The rail haulage system will utilise over 20 km of track while crushing is accomplished by way of three gyratory crushers each with a capacity of 3300 t/h. Nine conveyors operating in two parallel systems, each system over 3 km in length, will move the ore from the crushers to the stockpiles. These systems require a network of larger tunnels and mass excavations to accommodate the planned production facilities.This paper will describe the ore handling system, tunnel and mass excavation methodology as well as some of the challenges encountered with ground conditions and excavation quality during the execution of the project. A combination of lateral and vertical development methodologies and equipment, including drill jumbos, mechanised raise climbers and specialised ground support equipment, have proven successful in the development of a quality ore handling system.CITATION:Pasek, I, Firdausi, H and Chenier, T, 2016. Development of the ore handling system at the Grasberg block cave mine, Indonesia, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 599–608 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

The construction of the pipeline was completed in June 1956 and the line placed into operation in December 1956, ie. it has now been in continuous operation for approximately three years under an operating pressure of up to 350 lb. p.s.i.In reviewing the operating experiences of the line we must consider three major factors, which are:(a) The effectiveness to date of the protective methods for prevention of corrosion of the pipeline, ie. the preservation of the asset.(b) The maintenance of the line in regard to interference as to its stability which could be occasioned by erosion of the line, land-slides, accidental interference by the public, or construction authorities, etc.(c) The operating techniques employed.PROTECTIVE METHODS OF THE PIPELINESo to permit a clearer appreciation of the effectiveness of the protection of the! steel pipe against corrosion, I will briefly describe the methods used in the construction of the line.The line, which is 18 in. O.D. by %6 in. thickness steel pipe, is located approximately It miles south of the main Melbourne/Gippsland electrified railway.The steel from which the pipe was manufactured conforms to ASA.A33-1937 with the following modifications.Minimum elongation on a 2 in. test specimen...

Jan 1, 1960

As this is the first occasion I have had, and probably will be the only opportunity I shall have, of addressing such a large gathering of members and of student members of the Institute, I desire to- express my very deep appreciation of the honour 'you have paid me in electing me to the office of President for the current year. I realise also that such selection is a tribute to the Company which controls operations here, the centre selected for the annual meeting, but nevertheless there is afforded to the recipient a great deal of pride and of pleasure to hold the highest office in what is, in my opinion, undoubtedly the most important engineering society in Australasia.The past year has witnessed an unprecedented and unparalleled event in the history of the British Empire, and I think that we must all feel a wonderful sense of proud patriotism; the whole world was forced to admire the public calm and the dignity which accompanied the change in our Sovereign Ruler, and great tribute is due to the statesmanship of the Prime Minister, Mr. Baldwin. At this time, we should, I think, place on record our prayer, in common with all his people, that His Majesty, King George the Sixth, may enjoy a long and prosperous reign.The meeting at Port Pirie recalls one who did so much for the advancement of mining and metallurgy, especially in Australia. I refer to the late Mr. Delprat, who, as General Manager of The Broken Hill Proprietary Company Limited, had under his control for many years the smeltery in this centre. As you are aware, he had been elected an honorary member of this Institute, as well as of our sister Institutes in England and in America...

Jan 1, 1937

The geologist is often called upon to give judgment on the possibilities of reviving a former mining field presumably worked out as far as the evidence then available indicated. From time to time, scarcity and consequent high prices of metals has led to there-examination of many old fields. The possibility of resuming investigation on them where the practical miner ceased work, even where he had the aid of the trained geologist, has long since disappeared.Means of access to mines have been removed and water fills the workings. Hence an indirect mode of attack becomes essential.This method depends mainly on past history, and may be described as a reaching out by faith supported by shrewd guessing from the known to the unknown. Apart from whatever general intelligent observations may be made in situ of the evidence of former mining activity, the method depends largely on the examination of the past history of the field as revealed in the official records, company reports, plans of underground workings, local newspaper accounts, and the testimony of practical miners formerly employedon the field, the' reliability of which has to be carefully sifted. The matter derived from the examination of these sources must next be rigorously collated and correlated where possible. When the review of all individu!1l features and aspects has been completed, tentative and speculative conclusions may be drawn which, though not verifiable before the event, will usually prove to be more serviceable guides in exploratory operations than mere "blind stabbing."As an actual illustration of what is involved in the mode of procedure outlined above, the following is the description of an investigation in which the writer took part.In 1937, during the course of the Commonwealth Aerial, Geological and Geophysical Survey of Northern Australia, a detailed geological investigation was undertaken of the Croydon gold field, situated near the south-eastern. extremity of the Gulf of Carpentaria in North Queensland.The history of the field briefly is as follows: It was discovered in 1885, reached its peak of production 1896, declining thereafter till 1906, when operations ceased. The total production was about 1,000,000 ounces of gold bullion, containing approximately 40 per cent. of silver. The gold bullion was won from flat-dipping quartz reefs, which yielded an average of 2.oz. to the ton, and the maximum depth to which production occurred was 500 feet. Subsequent prospecting below this depth failed to locate further ore.In consequence of the inaccessibility of the mines and the almost total masking of the' surface by alluvium, the investigation of future possibilities became largely an. office ,study, which was conducted under the following headings:-1. Recording of factual data of each mine separately.

Jan 1, 1950

The variation of carbon monoxide and hydrogen utilization with the amount of the reductant in the blast furnace bosh gas was investigated for the No. 4 blast furnace at The Broken Hill Proprietary Co. Ltd.iron and steel works. Newcastle. The degree of CO utilization decreased with increasing CO in the bosh gas; the H., utilization increased with the H., content of the gas. Empirical relationships for CO and H., utilization are proposed.H2, is 3-6 times as effective a reductant as CO at present levels of CO (34-39 per cent) and H2 (6-10 per cent) in blast furnace bosh gas. H2, gas injection into the blast furnace is proposed as a means of lowering the coke consumption, and the economics of H2 injection are evaluated.

Jan 1, 1975

ONE of the phases of mining wide ore-bodies, such as are found in Broken Hill, is the laying-out and design of the sill floor gangway timber, When, in the above operation, a detail has to be repeated frequently, it is desirable in the interests of efficiency that that detail should be standardized as far as possible. Before arriving at a standard design e.g., a crosscut layout-it would seem necessary to compare its strength with some other unit of timber and see that the general design is at least as strong as the unit that has been taken for comparative purposes, In these notes no attempt is made to calculate the stresses to which timber underground is subjected, but merely to draw a comparison between the relative strengths of the various cross sections of timber in common use underground.It has been assumed for the purposes of comparison that the milling exerts pressure in a vertical plane only, and is uniformly distributed over any area. A beam supported at both ends, and with a uniformly distributed load, has the maximum bending moment at a point midway between the points of support, and equals- WL2 8 where W = load per unit length. L = distance between points of support.The bending moment also equals M-, where y M = modulus of rupture of the material in question. I = moment of inertia of the section of the beam about a given axis.Y = distance of extreme fibre from that axis. WL2. I The formula -8- = MY- only holds good until the elastic limit...

Jan 1, 1923

G. R. Compton (Gold Mines of Kalgoorlie (Australia) Ltd., Fimiston, W. A.) : In congratulating Mr. Hooker upon his resume of Mr Parry's paper I have in mind the fact that he carried out the research into pipe pressures. Hydraulic filling as practised in Kalgoorlie has created world wide interest, with these pressures and percolation being vital points.Early in the 1950s, representatives of the Kolar field were conduGted over the local mines where stopes at depths below 2,000 ft were being filled. The problems of pipe pressures were their main consideration since depths of up to 10,000 ft were envisaged.Mr Krishnaiah and Mr Murthy from the same field are with us today and perhaps we may hear of their experiences with depths of 6,000 ft and long lateral lines.J. Holly (Lake View and Star Ltd., Fimiston, W.A.): There is one phase, which I would like to mention myself, that has been very evident in Kalgoorlie operations. That is, we do not get the percolation properties that are obtained on many other fields in the world, and our tendency here has been to assess the quality of our fill more by its settling rate, i.e. the rate at which we can draw off clear water at the surface of the filling levels, rather than the rate that this water percolates down through the fill before it consolidates.We are tending now to measure the quality of our fill as a settling rate rather than as a percolation rate.Americans talk about percolation rates being the important property: If anyone has any experience on operating with fills with different percolation rates, I think their views would be very interesting to the meeting art this stage. Mr ...

Jan 1, 1965

The works of Metal Manufactures Ltd are situated at Port Kemblam NSW, within a few hundred yards of a deep-water harbour. At present they occupy about 26 acres, and ample provision has been made for future extensions. Rail connection exists between various parts of the Works and the main South Coast Railway, the harbour jetties and the adjacent copper refinery of The Electrolytic Refining and Smelting Co Ltd. A plan of the works is shown in Fig 1.The company was incorporated in March 1916, and commenced production of copper wire in June 1918. Early in 1920, tube manufacture was undertaken, followed by telephone cable mnufacture in 1923. Today the Works consist of five principal sections: Founrdy, Tube Factory, Wire Factory, Cable Factory and Case and Drum Factory. Whilst the last four are engaged in producing the finished materials for despatch from the Works, the first-mentioned is engaged in producing copper, brass, and other non-ferrous billets for use in the Tube and Wire factories. In addition, there are Engineering and Metallurgical Departments supporting the manufacturing sections, and in these, as well as in all other sections of the Works, extensions have been carried out from time to time to provide for increased output and new types of products.

Jan 1, 1938

Following the experimental work of Denny, Robson, and Irwin, and the clinical investigation by Crombie and Blaisdell, an investigation of aluminium therapy was begun at Washington, Pa., which is situated In a very large industrial section of the State. Some of the men to be studied were from plants manufacturing silica brick, refractories used in steel and glass manufacturing, and semi-porcelain table-ware; others were workers in foundries, sand blasters, and men engaged in the quarrying of ganister rock.This group of workmen gave an opportunity to study the effects of aluminium on various types of silicosis which differed somewhat from that found in hard-rock miners.EXPOSUREIn their occupations, the men studied were exposed to silica dust concentrations ranging from 17 to 97 per cent free silica. In the silica brick industries, the unfired product averages 96 per cent silica in the form of quartz, whereas the fired brick contains 50 to 62 per cent. cristobalite plus 11 to 80 per cent. tridymite, forms of silica that, on account of their higher solubility, are more toxic than quartz. The operational dust counts in the plants varied from 15 to 9,500 particles per c.c., and the median particle size from the aerial samples was 1.0 micron for the green product and 2.0 microns for the fired product. The length of exposure varied with the occupation as well as with the individual plant, but disabling silicosis could be produced in less than four years in certain exposures. The average time needed to produce radiological silicosis in those susceptible to this disease was eight years. Some of the men in our series of cases have been treated as long as fifteen years after exposure had ceased, and have improved under treatment.The dust counts mentioned above had been reduced prior to the aluminium therapy studies and the presen.t exposures do not exceed '900 particles per c.c., the average being 370 particles. per c.c. This improvement in dust conditions was due to improved dust control apparatus, which was installed before aluminium therapy was instituted. Aluminium powder is not a substitute for dust control.PATHOLOGYThe pathological picture of silicosis in men engaged in the ceramic industry is somewhat different from that in hard rock miners." Due to exposure to high concentrations of dust containing high percentages of silica of varying degrees of solubility andvery small particle size, these men are subject to a relatively rapid type of silicosis, which sets up an acute...

Jan 1, 1945

By T Atchison

The Vale Ferro Carajßs S11D project in northern Brazil is based on the movement of unprecedented volumes of waste and ore for mobile in-pit crushing and conveying or ætrucklessÆ systems. In peak years, the system is intended to handle a combined 160 Mt of material.The planning and implementation of the first such system for Vale, in a remote greenfield site, utilising the services of a range of international study, design and supply partners has provided a unique set of technical and project delivery challenges. The lessons from these are of value to the industry as the trend to remote and high-volume operations continues.This paper describes the key features of the mining system and documents the challenges and mitigations for important technical, cultural and project delivery issues that have arisen. It is a combined description of the journey taken by both Vale (as owner) and SKM (as delivery partner) over the course of many years.CITATION:Atchison, T, 2013. Lessons from the S11D truckless mining project, in Proceedings Iron Ore 2013 , pp 177-184 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

Significance of Ion Interactions in Flotation in Saline and Brine Solutions

Sep 13, 2010

By R Handfield, G Kary, Frieda Project

Recent exploration by the Cyprus Amax-Highlands Pacific-OMRD Joint Venture at the Frieda River project, PNG has demonstrated the extent of igneous phases, alteration and mineralisation, and the relationships between the various mineralisation styles in this major Cu-Au porphyry-epithermal system. The project area is in the obducted volcano-sedimentary section of the New Guinea mobile belt 78 km NE of Ok Tedi. It is between two major NNE dipping faults interpreted to have undergone thrusting then sinistral shear in the Late Miocene to Recent. The Frieda River Igneous Complex is a 15 km +7 km ovoid area with a central pod of basaltic andesite volcanics with cogenetic diorite to quartz diorite subvolcanic intrusions, and flanking clastic sediments. A series of late-stage, hornblende quartz diorite plugs ring the main igneous mass. The igneous rocks have a normal K calc-alkaline character with a very limited compositional variation. The intrusives are exposed on the eastern flank of the complex and have five mappable units and numerous defined phases. The southeastern quarter of the complex is host to a cluster of at least seven stockwork porphyry copper and skarn-hosted deposits within an area of 4.5 +3.5 km. The Horse-Ivaal and Koki deposits have identified resources totalling 804 mt @ 0.46 per cent Cu and 0.3 ppm Au, and the other deposits are in various stages of exploration. All these deposits are related to the Horse Microdiorite phase of the Complex and are outlined by a zone of potassic-propylitic-SCC alteration. Local overprinting argillic and advanced argillic alteration is related to a separate, post-porphyry mineralisation intrusive phase. The recent emphasis has been on the identification of higher-grade zones using ideas of structural control and specific intrusive-alteration-mineralisation relationships within the known resource areas. An elongate area 13 km x 4 km in the centre of the Complex has advanced argillic alteration in the volcanic rocks. This alteration zone hosts the Nena deposit (52.8 mt @ two per cent Cu and 0.7 ppm Au) and approximately 20 prospects of high sulphidation type. These deposits are distributed along two prominent NW-trending siliceous ridges interpreted as regional scale structures. Nena is a pod of vein and replacement sulphides hosted in a tectonically controlled multiphase breccia that overprints the advanced argillic alteration. The Nena deposit is 4 km from the nearest of the major porphyry occurrences. It is underlain by basemetal veins and minor porphyry mineralisation that are related to the Flimtem Trachyandesite intrusive phase. The recent search for additional Nena-type ore has focussed on the siliceous ridges using detailed structural and geochemical ore control criteria. Widespread, but poorly mineralised, basemetal-bearing carbonate and sulphate veins form a ring around the mineralised area. These veins have sericitic selvages, cut the porphyry mineralisation, but are cut by and locally underlie the silica-alunite phase of the advanced argillic alteration. The current model is that there are discrete intrusive phases responsible for each of major hydrothermal events at Frieda. These include from oldest to youngest:the Koki phase has no related alteration or mineralisation; the dominant Frieda phase has the hornfels, early skarn and minor magnetite-chalcopyrite mineralisation; the Horse phase has the bulk of porphyry copper and skarn-hosted mineralisation and minor basemetal veins; the peripheral Knob phase is barren; and the Flimtem phase has the high sulphidation epithermal deposits and minor porphyry and vein mineralisation. The intrusive phases span the interval 17 to 11.5 Ma and are co-magmatic. They represent discrete batches off the parent magma, rather than simple fractionation products.

Jan 1, 1999

THE furnace described in this paper was installed and has been used by the writer for the melting of rich gold-bearing material, and has given complete satisfaction. It may, therefore, prove of interest to other metallurgists who are faced with a similarproblem. A furnace of this type should be most suitable for the reduction of "cyanide preeipitate," "charcoal ash," "anode sludge," &c. formerly the melting was done in fire-clay crucibles, using coke or crude oil as fuel, but this method is costly, slow, and unsatisfactory. A small water-jacketed blastfurnace was also tried on this material after briquetting it, but was discarded in favour of the electric furnace. The furnace may be described as a simple form of the Heroult resistance furnace, with an adjustable upper electrode and a fixed bottom electrode. This is in accordanee with Stansfield's classification of electric furnaces. The heating is mostly due to the resistance offered the current by the molten slag. The melting chamber consists of a steel drum 14 in. in diameter and 21 in. high, and is lined with silica bricks specially made to fit the shell. The internal diameter is G in. The bricks contain 92 % silica, are made from calcined quartzite bonded with fireclay, and are similar in composition to those used for lining steel converters. They are set in a mixture of finely-ground quartzite and clay, and well dried out. The shell is bolted to a steel plate, which forms the decking of a truck running on rails, so that the furnace can be moved under ahood for carrying off the fumes. A cast-iron slag spout is bolted to the shell below the tapping hole, which is 4 in. from the bottom of the shell. Opposite this another hole 1 in. in diameter is drilled through the shell and lining for the passage of the lower...

Jan 1, 1918

Based on the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters a relationship is predicted between oxidic nickel in slag, oxygen in matte and the Ni/Fe ratio in the matte. Oxidic nickel in the slag is found to increase with an increase in oxygen content of a matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1980

Samples of a refractory copper ore were examined to test their response to segregation roasting, flotation, and acetonitrile leaching. Recoveries in the segregation roasting stage were between 60 and 100 per cent, while flotation recoveries varied between 60 and 85 per cent in cleaner concentrates assaying 25-40 per cent copper.The fraction of the copper which could be leached from the concentrate by an acetonitrile/sulphuric acid/cupric ion leach solution varied from 16 to 97 per cent, the lower recoveries being correlated with the presence of sulphide in the concentrate.

Jan 1, 1973

Were it simply a matter of extracting tin from the simple tin sulphide, the proposition would undoubtedly be simple enough. When, however, other valuable metallic sulphides are combined with the tin, and it is required to separate these intomarketable products, then the proposition becomes somewhat complex, and such is the case with the class of material of which I am about to write. The locality where it occurs is Howell, New South Wales, and chiefly at the Conrad Silver-Lead Mine. The tin sulphide occurs chemically alloyed with copper, iron and other metals associated with galena, pyrites, mispickel, blende and silver sulphide in varying proportions, and generally in a gangue of highly crystallised quartz.Several varieties of tin sulphides occur, and from the following analyses of three minerals, these being specimens specially selected free from foreign matters, it will be seen that the chemical composition is somewhat complex.

Jan 1, 1902