Search Documents

By J Finlay, P Betts, D Milton, H Williams

The aim of this paper is to present an innovative method to help delineate potential target volumes for haematite-goethite mineralisation as opposed to more magnetic ores. This is achieved through interpretation and modelling (2.5D and 3D inversions) of ground magnetics and gravity surveys over the Koolanooka South prospect in Western Australia. The targets are assumed to be dense and weakly magnetic and hosted within banded iron formation (BIF) horizons. Geophysical interpretation (2D map) was performed using a variety of processed magnetic and gravity images (Betts et al, 2007) to determine the distribution of lithologies, to understand the structural architecture and to map out any anomalous areas of excess density (possibly indicating goethite alteration). The created geological map is used to build geological cross-sections (geometrically consistent) that were modelled (in 2.5 D) against both potential field datasets. The crosssections are consequently used as the framework to build a 3D geological model. The model defines 3D volumes of rocks including several BIF horizons. The distribution of densities and magnetic susceptibilities of the BIFs is inverted within the GOCAD«-VPmg environment to reduce the misfit between the response of the model and the observed gravity and magnetics. By combining the results of both petrophysical property distribution it is possible to map out (using classical GIS type queries in 3D) volumes of higher density and lower magnetic susceptibility.

Jan 1, 2009

The paper describes the preparation of new rail guides, removing existing rails, and replacing with new rails in a vertical winding shaft.INTRODUCTIONThe general practice in coal winding shafts is the use of two cages, with one or more decks in which men and materials are raised or lowered. Winding speeds vary according to depth, the type of winding gear, and whether winding is done in downcast or upcast shafts. Each cage occupies a position between the centre and side of the shaft, with a clearance depending on the type of guides used. The function of the guides is to keep the cage in position throughout the entire depth of the shaft. There are three types of guides, two of which are in general use.1. Selected wood of about 6 in. square section, fixed to the side of buntons.2. Solid strand steel made up similarly to that of an ordinary wire rope, suspended from the head frame with weights attached to the lower end.3. Standard T-rail sections fixed to end or side buntons. Of the three types, 2 and 3 are in general use. The type used in the particular case, the subject of this paper, is T-rails of the standard section used in railway work.GENERAL DESCRIPTION OF SHAFTDetails of the shaft are as follow: Diameter of shaft: 22 ft. inside lining.Depth of shaft: 900 ft., including sump.Concrete lined throughout.VENTILATIONThe ventilation shaft is used for the upcast, through which all vitiated air passes to the main ventilation fan. Quantity of air passing up the shaft is 400,000 cu. ft. per minute. The air is highly saturated during the summer weather and slightly less...

Jan 1, 1947

By S J. Schafrik, C Keles, C Schlosser, E S. Gilliland, A K. Louk, N S. Ripepi, S Keim, J Amante, E Diminick

Three legacy coalbed methane production wells have been converted to injection wells for a one-year carbon dioxide (CO2) injection test to evaluate the potential for CO2 storage in the coal reservoir and the potential for enhanced gas production at offset wells. The injection reservoir is composed of 15–20 individual coal seams with an average thickness of 30 cm (1.0 ft), spanning a depth range of approximately 240 (800 ft) to 670 m (2200 ft).The monitoring program for this test includes gas and water sampling of the three injection wells, three dedicated monitoring wells and approximately 20 offset production wells. Key technologies used for monitoring the study area include time-lapse GPS and interferometric synthetic aperture radar (InSAR) acquisitions for surface deformation measurement, a 28-station buried passive microseismic monitoring array, real-time downhole pressure and temperature sensing and perfluorocarbon tracer fluids, which will be injected with the CO2 stream. The schedule for the monitoring program includes pre- (baseline), during- and post-injection data collection. This schedule will allow data to be analysed for time-lapse changes and trends, which are important for understanding the migration of gas and fluid phases in the reservoir – including CO2, methane, other hydrocarbons and water – and for observing the changing distributions of reservoir pressures and stresses.The results of the monitoring efforts for this study have implications for monitoring mining operations. The combined use of GPS and InSAR geospatial data to evaluate elevation changes across and beyond the study area may prove to be an accurate option for measuring surface deformation, including mining-induced subsidence, in unstable terrain. Long-term microseismic monitoring using high-sensitivity instruments has several applications in mining operations, including rock stability monitoring, production monitoring and miner location detection during emergencies. Tracer studies and short-term microseismic monitoring used to assess methane extraction can also be used to develop and optimise degasification systems for underground coalmines.CITATION:Gilliland, E S, Ripepi, N S, Schafrik, S J, Schlosser, C, Amante, J, Louk, A K, Diminick, E, Keim, S, Keles, C and Karmis, M, 2015. Monitoring design and data management for a multiwell CO2 storage/enhanced coalbed methane test in a stacked coal reservoir, Buchanan County, Virginia, USA, in Proceedings Third International Future Mining Conference, pp 47–56 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By G Hancock, A Kemp, I Taylor

The mine site is situated south east of Port Hedland in the Pilbara region of Western Australia. A detailed engineering design was undertaken for six irregularly shaped waste rock dumps at the site. The design was undertaken to ensure long-term stability of the dumps and optimise material movements for closure construction. The Watershed Erosion Prediction Program (WEPP) and SIBERIA landscape evolution modelling was undertaken for the landforms using regional and site-specific material characteristics to provide an indication of the maximum allowable slopes and corresponding slope lengths for long-term stability.The majority of the waste materials present in the waste rock dumps are considered likely to be subgrade banded iron formation (BIF) and chert, which is generally competent material. The presence of a large number of dolerite dyke swarms indicates appreciable volumes of dolerite were produced as waste from the pits. Geological records also indicate that the dolerite is logged as being heavily kaolinised in the geological logging, hence kaolinite is very likely to be present within the waste dumps on-site. This material has an elevated risk of being highly erodible/dispersive. Clays and shales are also likely to be present in the dumps and are considered to be less competent material (relative to the BIF/chert).The final design configuration of the largest existing ‘unplanned’ waste rock stockpile is compared to a hypothetical continuous ten degree outer embankment alternative. This paper will present a brief description of the alternatives for closure of three waste dumps in close proximity to each other and how the detailed design based on site-specific materials and conditions compare to an alternative approach blankly assuming that most materials will be erosionally stable at less than ten degrees.CITATION:Kemp, A, Taylor, I?and Hancock,?G,?2014. Landform design for Pilbara mine site – why plan and design waste rock dumps for closure based on site-specific conditions?, in Proceedings Life-of-Mine 2014 , pp 47–54 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

IT will be noticed, from the following contributed papers on the various plant, what an infinite number of parts are required to be kept in active operation in order to derive a resultant product of commercial value from the ores and materials received at the works. Crude ores and concentrates, in every degree of complex structure and resistance to treatment, are arriving daily from near and distant places, moreover their metallic contents are so varied that an outsider, unacquainted with the operations, would naturally wonder how it is possible that the rare elements are to be sorted out and classified into their true order, to meet industrial requirements.The proposition is necessarily not a simple one and owners of mining properties have naturally refrained from smelting their complex ores on account of the technical difficulties of attaining high efficiency and recovery of the metals, where limitations are imposed in procuring a variation of ores that lead to the best smelting and refinmg result. This difficulty obviously imposes many disabilities on the smelter, who is prepared to accept all such complex ores, and it may be said that were therenot available a large weekly supply of lead concentrates from the company's own mine at Broken Hill, of standard quality, much of the material being treated in the world today would certainly not be marketable.In order to sustain full efficiency, each section of the works must maintain its.true balance and synchronize with the requirements of such other departments as are dependent on its partially treated materials. This harmony of operations is not only imperative as regards tonnage output, but also relies on the condition of the resultant treatment by each plant, no large variations being permissible.The various officers are, therefore, dependent on one another to keep the order of the operations flowing regularly. This is accomplished by constant intercommunication and observation, as...

Jan 1, 1918

By Saghafi A, Kelly M, Williams R. J

A two year program of research into the feasibility of long-hole drilling for improved gas emission control has been undertaken at Appin Colliery. State of the art equipment was employed involving cableless electronic surveying and down-hole motor drilling. The project involved the drilling of 1000 m long, in-seam boreholes in the Bulli seam and boreholes of similar length drilled cross measure and then in-seam along the underlying Balgownie seam. A new concept for gas drainage was defined, employing long-holes for both predrainage and post drainage.

Jan 1, 1988

By P J. Hawke

Within the Mesa J pisolitic iron ore mine, clay is distributed unevenly throughout the deposit and often forms as pods and channels less than 10 m in width. The mine resource model, based on 50 m + 50 m spaced drilling, has been unable to accurately delineate the clay for scheduling and mining purposes. Therefore, alternative methods for mapping the clay-contaminated ore were sought. Predictive clay mapping will significantly reduce production costs at Mesa J through improved selective mining practices, more accurate scheduling, reduced wear on mining equipment and minimising the need for maintenance of haul roads and ramps. High lateral resolution electromagnetic (EM) surveying using a Geonics EM31 instrument can quickly and inexpensively delineate the extent and orientation of the clays. Preliminary results indicate that a block model based on the interpretation of the EM data can accurately predict the distribution, volume and tonnage of ore and waste material. While rip-line mapping, infill drilling, ground penetrating radar and gravity can delineate clay with various degrees of success, none were as efficient as EM31.

Jan 1, 2002

By I C. Carrasco, V G. Mirada, J F. D Domingo, F S. Leite

This paper investigates ore loss and dilution produced by rock movement in bench blasting. A total of four blasts, in which electronic detonators have been used, were monitored in Cobre Las Cruces Open Pit Mine (FQM Ltd) in Gerena (Sevilla, Spain). Rock motion has been obtained in 137 points of the free face and 6 points inside the block. Multiple liner regression has been applied to predict rock motion and estimate ore dilution as a function of hole coordinates, rock contacts, powder factor/hole, amount of explosive per blasthole, burden, spacing, hole length, stemming length, explosive energy, hole row, subdrilling, blast sequence, stiffness ratio, blasthole distance to free face, rock density and Young’s modulus. The model is statistically significant with a determination coefficient over 0.8. Rock motion measurements in 31 more points have been used to validate the model and to show a reduction in ore dilution.CITATION:Domingo, J F D, Leite, F S, Mirada, V G and Carrasco, I C, 2015. Dilution, ore grade and blast movement calculation model, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 71–78 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By K P. Crameri

The Beta Hunt orebody is situated on the south western limb of the Kambalda dome. It is one of the nickel occurrences in the area which fall into the category of æKambalda Style OrebodiesÆ. These orebodies are renowned as being continuous uniformly mineralised ribbons of nickel sulfide mineralisation. Interestingly, Beta Hunt does not conform to this notion of continuity and uniformity and is in fact highly irregular in its ore distribution due largely to the influence of post depositional structure. In an attempt to understand the ore distribution at delineation stage rather than development stage a detailed footwall topography model is created using all available drilling data. To augment this drilling data, the routine use of downhole EM and borehole radar has been introduced to provide data beyond the confines of the drill core to enhance the geological interpretation of the footwall topography and the distribution of the mineralisation. The implementation of a detailed footwall model and the use of downhole geophysics has proved to be very effective in resolving the orebody complexity issues. Ongoing development of the methods used will continue to refine the interpretation of the geology to enable more efficient extraction of the orebody.

Jan 1, 2006

By A Crosky, S Saydam, H Chen, H L. Ramandi

Cable bolts and rock bolts are used as primary and secondary anchoring systems in many underground mines. Reports on the premature failure of cable bolts and rock bolts due to stress corrosion cracking (SCC) in underground coalmines have been increasing in the past two decades. The previous studies found that the SCC in both rock bolts and cable bolts occur as a consequence of atomic hydrogen diffusion into the material, which is known as hydrogen-induced stress corrosion cracking, HISCC (Craig et al, 2016; Wu et al, 2018b). While research to understand the process of SCC occurrence in underground mines is still required, finding a prevention solution to protect the bolts from HISCC is crucial. In this study, we analyse a variety of commercially available coatings for steel corrosion prevention, including barrier coating (ie epoxy, polyester TGIC) and sacrificial coating (hot-dip galvanising). We test the coating on coupons manufactured from rock bolts and cable bolts used in the coal mining industry.

Nov 29, 2022

By B Washington, A Campbell, R Taylor

A sampling and measurement program was undertaken on the reaction shaft of the Olympic Dam copper flash smelting furnace. The object of the work was to provide information to validate a mathematical model of the burner and reaction shaft. Samples and measurements were undertaken through the burner inspection ports and the South East (SE) shaft sampling port about half way down the reaction shaft. Samples were collected to enable the calculation of particle loading of shaft gases, or sizing and chemical analysis of the partly-combusted feed, and the preparation of polished sections. Measurements were made of the temperature and sulfur dioxide content of the atmosphere, as well as plume velocity.To implement the program it was necessary to design and construct the following specialised items of equipment. For use at the burner inspection ports: a cup sampler for obtaining samples below the burners (temperature, solids loading and samples for characterisation).For use at the SE shaft sampling port and also at the settler level: trough sampler (plume definition and samples), isokinetic sampler (used as a velocity probe in this work), temperature probe (temperature traverses across the shaft), and sulfur dioxide probe (SO2 measurements across the shaft).The design of the sampling and measuring equipment is described, and examples are cited of the types of information obtained. The problems arising from working in a hot environment with molten or sticky particles are discussed.

Jan 1, 2005

By B Jones, M Chappell

Installing ground support correctly is not an easy task, whether lack of operator training, poor ground conditions or underperforming equipment. Confirming the quality of installation can help with planning and remedial works and help to maintain a safe working environment. A 2?m bolt with 700?mm of encapsulation will pass a 10?t pull test (assuming ground conditions permit); however, it will not provide any data of the unencapsulated length and thus the ability to withstand corrosion. Complimentary testing in the form of non-destructive testing (NDT) can provide factual data that leads to the assessment of the quality of the encapsulation. By improving the quality of the encapsulation, the risk of corrosion is reduced, the ground support durability is improved and hence the asset life is enhanced.This paper presents a case study of a trial using the NDT system RokTel™. Installations of varying quality were installed and tested. The characteristics tested were corrosion, load and free length. These characteristics can be tested and assessed for cable bolts, thread bar bolts and split sets. The aim of this paper is to present NDT testing as a viable method for assessing installation quality and ongoing performance of the ground support.CITATION:Jones, B and Chappell, M, 2014. A non-destructive testing method for measuring bolt condition, in Proceedings AusRock 2014: Third Australasian Ground Control in Mining Conference , pp 307–314 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 5, 2014

By D Wimpenny

The Bogong Power Development Project in Victoria, Australia involved the construction of a 15 m long mass concrete plug up to 9 m in diameter within the head race tunnel. The plug is critical to theperformance of the scheme as it permanently seals the head race tunnel under approximately 300 m head of water.The location of the plug in the headrace tunnel was determined by a programme of in situ rock stress testing using both hydrofracturing and over coring stress testing methods.In recognition of the importance of the plug, the Head Contract specification requires that its temperature during hydration be controlled using an embedded cooling system. In addition, contact grouting and curtain grouting around the plug cannot commence until thermal contraction was substantially complete.This paper describes the use of bespoke fi nite element software to model the temperature rise in the plug and design mitigation measures to control temperature rise in the plug. These measures include restricting the concrete placing temperature to 10°C, incorporating 39 per cent fly ash in the concrete and installing embedded cooling circuits.Site trials were undertaken to calibrate the model for the proposed concrete mix. The cooling system comprised 25 mm ID pipes forming twelve separate circuits that fed 7°C water from a single chiller unit. The cooling system reduced the peak temperature in the plug to approximately 30°C and the associated risk of early-cracking. The time before contact grouting could commence was shortened to less than two weeks from casting.

Mar 8, 2011

By A Sainoki, D Fukuda, K Shioya, C Zhang, M Sharifzadeh, T Yamaguchi, S Saydam, J Kodama, C A. Amagu, Y Fuji

In an open pit mining, ensuring stability of rock slope has been one of the major challenges. As the instability of rock slopes can results in slope failures; consequently, endanger the lives of workers, affect mining operations, and often lead to economic losses. Therefore, it is practical important to study the stability of rock slopes to ensure safe, smooth, and effective mining. The stability of rock slope of about 130 m height at Higashi-shikagoe limestone quarry, which has experienced slope failures four times since 1996, was assessed. The rock mass at the quarry is consists of mainly limestone, schalstein and slate rocks intersected by clay seams of about 70 m thick at footwall of the rock slope. Previously, the effects of limestone excavation at the foot of the rock slope and shear failure due to rainfall infiltration have been investigated. Although clay is widely known to plays a vital role in the stability of slopes in engineering projects including mines, but its impacts on slope deformation at the study quarry are not adequately examined. Therefore, the present study addressed the impact of presence of clay on slope deformation at Higashi-shikagoe limestone quarry by employing both field displacement measurements and numerical simulation. Firstly, surface displacements measured by automated polar system (APS) for over eight years were analysed to understand the overall characteristics of the slope deformation. The measured results show that the displacement gradually decreases with time. The maximum displacement of about 100 mm was observed at middle of the rock slope. Secondly, the effect of deterioration and plastic behaviour of the thick clay layer were simulated using two-dimensional finite element method (2D FEM). The simulated results reveal that the clay exhibited deterioration by water contact and plastic behaviour arising from mining activities at the footwall of the clay zone. Based on the characteristics of the measured and simulated results, it was found that the displacement induced by the effect of deterioration of clay is more noticeable at the north side of the quarry whereas displacement induced by excavation is quite significant at the south side of the quarry if clay behaves as an elasto-plastic material.

Nov 29, 2022

By B L. Coulter, E Wightman, A S. Burrows

With their commitment to sustainable development in an increasingly carbon-constrained world, many resources companies are focused on reducing the energy required to create their final products. In particular, the comminution and smelting of metal-bearing ores are both highly energy-intensive processes. If resource companies can optimise the energy efficiency across these two processing stages, they can directly reduce their overall energy consumption per unit mass of metal produced and thus reduce their greenhouse gas footprint. Traditional grinding and flotation models seek to improve the efficiency of mineral processing, but they do not consider the energy used by downstream metal production, eg smelting and refining. Concentrators and smelters individually may be running efficiently, but are they optimising energy consumption of the overall system? A key step towards answering this question is to understand whether it takes less energy to remove an impurity in the concentrator or the smelter. Analysis of the complete concentrator û smelter process chain may show that there are times when the concentrator should use more energy to reduce the overall energy requirements across the mill and smelter. The new methodology discussed here will integrate downstream processing energy with mineral processing energy, to find the overall most energy efficient circuit design and operating strategy. The proposed methodology includes: determining what grade and recovery positions can be achieved in the concentrator by using different combinations and amounts of grinding and regrinding, thermodynamic calculations of the energy used to process the different concentrate grades to metal, and integrating the concentrating and smelting models to find the lowest total energy for the system. A case study which investigates the effect of increasing regrinding energy on the overall mineral processing û smelting energy consumption is presented. For the copper-nickel sulfide ore investigated the addition of regrinding results in 11 per cent less energy being used in the overall concentrator û smelter process chain per tonne of metal produced. Although regrinding is often seen as an energy-intensive process, in this case study the use of 1 kWh of energy for regrinding reduces the overall energy consumption by 12 kWh. The new mill to melt methodology will allow companies to model energy consumption from mill to smelter with a view to reducing the energy-intensity and greenhouse gas footprint of their processing and smelting operations.

Jan 1, 2009

By S Sullivan

The key skills for a competent geologist are observation, documentation, analytical thought and the ability to communicate. These attributes have served the geological world for the past two centuries since the field of geology was separated out from natural philosophy. The understanding of the structural setting, lithologies, alteration and 3D distribution of the target mineral species are essential precursors to resource evaluation and potential economic extraction. The advent of artificial intelligence and machine learning has matured to the point where observation by dedicated sensors and analysis by customised AI algorithms can replace manual processes and deliver credible results. In combination with analytical data such as assays, various sensors now collect physical properties of rocks which are used as proxies for mineral identification and rock mass classification. These sensors include X-ray and infra-red spectra, magnetic susceptibility, gravity/density, EH/pH measurements, conductivity, colourimetric readings, porosity, fracturing and fracture intensity. Analysis using machine learning techniques trained using known data sets can determine rock type classification, rock density, quantification of grade/quality attributes, mineral alteration, weathering and geotechnical attributes such as rock quality. This type of data relies on calibration and quality control of a variety of different types of electronic hardware. The resulting data is non-additive, has error ranges and will be suitable for consumption by fast AI methods providing probabilistic analysis. A second stage could include geometallurgical constraints to provide an ‘extractability index’, which is of more interest to miners than pure geotyping. Using resultant interpreted geological criteria, 3D domain models with spatial attributes will be built.

Sep 1, 2024

By L L. Kuhar

The AMIRA International P843A Geometallurgical Mapping and Mine Modelling (GeMIII) project is an interdisciplinary research collaboration between 17 global mineral companies and four research organisations aimed at providing support for the emerging industry trend of geometallurgy. The main aim of the project is to develop predictive geometallurgical indices which can be incorporated into a resource block model to maximise the commercial value of an orebody and to minimise the social and environmental impact of mining operations.Researchers at the Parker Centre/CSIRO have been focusing on the development of predictive hydrometallurgical indices for the GeMIII project via rapid, small-scale, cost-effective tests and protocols for comparative ranking of attributes relevant to leach performance. The focus of the small-scale leach tests has been to determine the leach index (relative indication of leach performance), recovery, impurity deportment, reagent consumption, effect of size/degree of liberation and mineralogy of samples for their relative ranking. Predictive tests for heap leach hydrology (related to agglomerate characteristics) and slurry rheological behaviour are also being developed.

Sep 5, 2011

By H Kundapen, B R. Bolton, H Davies

The Ok Tedi porphyry copper-gold mine is located in the Star Mountains of Western Province, Papua New Guinea. Open-cut mine commenced in 1984 and is due to cease around 2010. The mine produces a total of 88 Mt of waste annually including 58 Mt overburden and 30 Mt tailings, which are discharged directly in to the Ok Tedi River. Mine derived wastes are transported downstream and deposited within the river channel in a variety of bar forms. The prevailing hydrogeological conditions including, velocity, competency, capacity, gradient, grain size and specific gravity, control the deposition and segregation of these sediments. Periodic exposure of the reactive sulfides to oxygen during fluctuations in the river discharge may result in oxidation, localised acid generation and liberation of metals into solution. To evaluate the significance of this issue, Ok Tedi Mining Limited initiated an investigation of the sediments deposited in the upper Ok Tedi River as part of its overall ARD Management Program. The specific objectives were to: evaluate the acid-forming characteristics of identified high sulfide river deposited sediments; characterise geochemically the waters in contact with sulfide-bearing river deposited sediments; map and monitor exposure areas and oxidation depth of deposited potentially acid forming (PAF) sediments; determine the depositional processes controlling sulfide distribution; and assess lag period, oxidation and metal release rates for the sediments. This work included the analysis of sediment and water samples collected on a 50 + 50 metre grid at six gravel/sand bars. The sediment samples were analysed for total sulfur, ANC, NAG, total sulfur and total copper. Water samples were tested for general water quality parameters, sulfate and a suite of dissolved metals including; Al, Ca, Cd, Cu, Fe-sol, K, Mg, Mn, Na, S and Zn. This paper presents the results of these investigations with particular emphasis on the geochemistry of the river sediments and associated contact waters.

Jan 1, 2003

By J G. McLellan, B Miller

Copper and Gold mineralisation at the Ernest Henry deposit is bound by two controlling shears along the hanging wall and footwall margins. The shear zone geometries have been influenced by a large diorite intrusion, dated at ca. 1660 Ma, which lies to the north-east and south-west of the main orebody. The shear zones, which partitioned strain prior to the main mineralising event ca. 1514–1504 Ma, and in conjunction with adjacent regional structures, have been a critical factor in the deposit location and geometry. Conventional exploration techniques have been utilised proximal to the current deposit since the initial discovery in order to expand upon known resources, with limited success. However, new geomechanical modelling techniques have now been employed to target structurally controlled mineralised zones in three dimensions. The main aim of the geomechanical modelling was to simulate the effects of regional deformation events to highlight areas of anomalous strain, which indicate areas with a higher likelihood of fluid focusing and mineralisation potential. This project was focused on testing the latter stages of a D3 event (NE-SW compression) to examine preconditioning of the system, and a D4 event (SE-NW compression) which have ultimately been responsible for the current location of the mineralisation.CITATION:McLellan, J G and Miller, B, 2017. Geomechanical modelling of the Ernest Henry iron oxide copper gold deposit – identifying fluid pathways to predict potential mineralised zones, in Proceedings Tenth International Mining Geology Conference 2017, pp 75–82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 20, 2017

By S Farrokhpay, C Akop

Copper-gold-pyrite ore types with an elevated pyrite head grade utilise a sequential flotation circuit to recover initially a copper-gold concentrate with a pyrite-gold concentrate being produced from the tailing of the initial circuit.A simpler flotation circuit with lower operating and capital costs for treatment of such copper-gold-pyrite ores with an elevated pyrite head assay was sought in the described work. After characterising the ore, the objective was to apply bulk rougher flotation of both the copper minerals and pyrite for the copper-gold-pyrite ore at natural pH. Hence, no lime or other pyrite depressants were required in bulk roughing. The bulk rougher concentrate was upgraded in a cleaner circuit to reject non-sulfide gangue and then the resulting sulfide concentrate was separated by depressing the pyrite to produce two products (copper and pyrite concentrates, both having significant gold assays). A standard test with a sequential circuit was applied to the same ore for comparison.The chalcopyrite and pyrite losses in the tailing from the rougher circuit were the same for both bulk and sequential roughing (less than six per cent). In cleaning (bulk circuit), the effective pH for pyrite depression was 11.8–11.9; copper recovery was 70–75 per cent (grade of 15–20 per cent copper) and the sulfur recovery (pyrite product) was 80–85 per cent (grade of 34–36 per cent sulfur).These results approached those for the sequential circuit where copper recovery was 80–85 per cent (grade of 15–20 per cent copper) and the sulfur recovery (pyrite product) was 83 per cent (grade of 38 per cent sulfur).The observed effects of feed sizing on the liberation of minerals in the rougher feed are discussed. Options for improving the bulk circuit results are also considered. Importantly, the implications of various aspects of these findings for the bulk circuit are discussed with an industrial focus.CITATION:Akop, C, Farrokhpay, S and Johnson, N W, 2014. An alternative circuit for chalcopyrite-pyrite ores with elevated pyrite content in Cu-Au ore treatment, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 407–416 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014