Search Documents

By R Munoz, R González, J Vallejos, A Delonca

In panel caving in underground mines, it is essential to characterise and monitor the stress and stability state of production level pillars to ensure the extraction of the mineralised ore column and the safety of workers. Pilar Norte is a sector in the El Teniente mine that forms a pillar between the undercut fronts of the adjacent Esmeralda and Reservas Norte sectors. It exists in a high-stress environment, which may induce damage to the rock mass production pillars. Generally, numerical models are calibrated using observed damage in galleries. This procedure does not discriminate between the structural condition and/or the blasting damage effects. This paper proposes a technique that uses borehole cameras to measure stress-induced damage. This has the advantage of being at the intact rock scale, meaning that the effect of geological structures is negligible and the blasting damage factor is eliminated. Comprehensive geotechnical characterisation and tomography monitoring has been undertaken at Pilar Norte to describe and determine the rock mass behaviour of the production pillars. By combining analytical, empirical and numerical models, a correlation between the measured overbreak recorded by the borehole cameras and the stress level of the pillar was developed. The methodology can be routinely applied to estimate the stress state in the production pillars.CITATION:González, R, Munoz, R, Vallejos, J and Delonca, A, 2016. Characterisation and monitoring of the stress state of production pillars at El Teniente Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 197–202 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By Sparrow G. J

The effect of polyelectrolyte flocculants on the de-watering of a tailing suspension of very fine clay was investigated.Sedimentation and filtration experiments were carried out in the labqratory to characterise the de-watering properties of the tailing. The results were used to calculate the effect of flocculant additions on the drainage and vaporation components of the de-watering of a clay suspension ponded on to a sand drainage bed.A flocculant increased the drainage rate, but decreased the volume of water that could be removed by drainage leaving more water to be lost by evaporation.The sorptivity values measured in the laboratory were used in the de-watering equation previously established for the tailing to estimate the effect of flocculant additions on the time required to de-water the suspension from 18.2 to 60 per cent solids w/w. The calculated de-watering times were found to increase or decrease depending on the volume of water removed by drainage and the prevailing evaporation rate.

Jan 1, 1980

By G Baiden

The removal of rock blockages in mining operations has long been a risky undertaking, especially in high overhead conditions. Moreover, the assessment of where to put charges and the placement of them has been difficult due to the lack of visibility and safe access to the area. Traditionally, wedging long poles with explosives on them to keep the operator at a relatively safe distance has been the tried and true method of attempting to remove the blockages. Unfortunately, this is not a perfect system as it usually takes several attempts to remove the blockage. Each successive attempt results in even more dangerous conditions for workers and/or damage to the mine due to the successively larger amounts of explosives used until the hang-up finally comes down.Over the years, different ideas have been proposed to improve this process and reduce the inherent safety risks. Some of the technologies that have been trialled include projectiles fired at the hang-up; large, cumbersome arms; and massive amounts of explosives, each of which come with their own inherent safety risks that result in dangerous situations for miners and the mine.After gaining a thorough understanding of the process, Penguin Automated Systems Inc has developed a robotic system that is capable of working in a rock blockage safely. The idea combines the latest in telerobotics technology with 3D scanning and underground geospatial positioning. The hang-up removal is performed by scanning the inside of the hang-up to rapidly develop a geospatially placed 3D model for the operator to use. The 3D model is detailed enough that the operator can attempt to pick the ‘keystone’. A blasting engineer or the operator can then determine the exact position where the explosive charge should be placed in the 3D model and thus at the actual hang-up. The operator, controlling the robotic arm, uses the 3D virtual reality model of the robot system and the actual drawpoint information model to display the location information, the arm can then reach into the hang-up to position the charge using the kinematic model of the robot system. The 3D model is used to provide views inside the hang-up so that the operator can move the arm safely and precisely. This process allows the operator to place the charge (using the 3D representation of the drawpoint) from a long distance away. As the process continues, the end of the arm drills the rock and precisely loads the explosives. The robot then returns the blasting cable to the command station, which is located in a truck at a safe distance from the blockage.This paper will review the development of the system and present the results to date.CITATION:Baiden, G, 2016. Robotic hang-up assessment and removal of rock blockages in mining operations using virtual reality for safety, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 745–754 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

Similarities and Dissimilarities in Florida Phosphate Ore Types - Surface and Bulk Property Analysis of the Flotation Feed, Concentrate and Tails

Sep 13, 2010

By N van Aarde, B A. Moore, S van der Merwe

Frequently materials handling operations are compromised by transfer chute problems ranging from high wear rates, blockages and ineffective loading of the downstream conveyor. This paper will present the design flow implemented to overcome problems in two case studies utilising discrete element modelling incorporating material characterisation.Material testing is relevant in achieving a valid discrete element method (DEM) simulation model and subsequently a valuable design tool for transfer chute assessment and design. It is well recognised that in the current growth and demand for mineral resources, leading to ever increasing conveyor capacities associated with export terminals and mineral processing facilities that transfer chutes are a key focus point. The successful performance of the transfer chute is also dependent on operating with a ærobust rangeÆ of material flowability and handling characteristics. This requirement is crucial in accommodating mineral ores from developing resources, which are often more friable and stickier than in past decades.This paper will include details of chute installations associated with iron ore and coking coal, from the DEM simulations through to the performance of the installed and commissioned plant.CITATION:Moore, B A, van der Merwe, S and van Aarde, N, 2013. Implementation of advanced transfer chute designs, in Proceedings Iron Ore 2013 , pp 445-450 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By A G. Thompson, E Villaescusa, A De Zoysa, J R Player

Ground support performance is critical to the safe and economical extraction of ore. This is particularly important for mass mining extractions at great depth, which are currently being considered by a large number of mining companies worldwide. As the in situ stresses concentrate around critical excavations, failure occurs at the excavation boundaries and ground support is required for the excavations to remain safe and accessible for their intended lifespan. Ground support consists of reinforcing elements that are installed within the rock mass to modify its internal behaviour (generally to within one excavation radius) and surface support elements that are installed at the exposed boundaries to retain the failed pieces of rock. For surface support to be effective, the loadings need to be transferred to the reinforcing elements; however, the combined performance of rock bolts and mesh is poorly understood in terms of the energy dissipation capacity available for a typical ground support scheme implemented at most mass mining operations.Over the last 15 years or so, a large number of large-scale laboratory experiments have been completed at the Western Australian School of Mines (WASM) Dynamic Test Facility for reinforcement systems and surface support systems loaded separately. The objective of more recent testing has been to establish the combined energy dissipation capacity of typical and enhanced reinforcement systems combined with mesh surface support. Total energy dissipation has been separated into energy dissipation attributable to the reinforcement and to the mesh. The results of the tests are presented and compared with the existing WASM design demand and capacity guidelines.CITATION:Villaescusa, E, De Zoysa, A, Player, J R and Thompson, A G, 2016. Dynamic testing of combined rock bolt and mesh schemes, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 789–798 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

In Broken Hill, Northern Rhodesia, two water jacket lead furnaces have been in operation for the past three years. The furnaces were erected in war time, and only absolute essentials were procurable. The water for the jackets was obtained from wells adjacent to the works, in a dolomite formation. There being no water-softening plant, except a small one capable of treating water for the power plant only, this water was found to make a heavy scale in the jacket. During 1917 several jackets were burnt through, resulting in serious trouble and loss of output. In order to avoid this, furnaces were stopped twice a month for 8 hours and scale was removed as far as possible. In addition to the scale trouble during the summer months, a green slime grew in the supply tanks and occasionally became detached from the tank and collected in the cocks near the jackets. This caused risk to the jackets and was difficult to remove without a stoppage of the furnace. In 1918, bundles of wattle bark were placed in the hot well at the rate of one ton per month. These extracted the tannin and added from 0.5 to one part of tannin per 100,000 to the circulating water. The hot water was cooled over a brushwood cooling tower and returned to the supply tanks. The well water required to, make up the wastage was estimated at 40,000 gal per day.

Jan 1, 1920

By D Connelly

There is now a new generation of mobile crushing and screening plant systems available which have been developed based on the motivation of reducing truck haulage. Newly designed mobile crushing and screening plant systems have the advantages of mobility, flexibility, economy and reliable performance, making this system very appealing for small- to medium-sized projects or projects where a number of resources are separated by distance.A brief review of the past history and experience with transportable crushing plants provides an insight into some of the issues with transportable plants in mineral processing. A closer look at a simple model based on exploiting small but high-grade orebodies suggests the concept has merit, however there are many more engineering, logistics, legal, technical and management aspects which have limited the application of such a concept in the resource sector. This paper explores the concept in detail and endeavours to analyse the preferred commodities and scenarios under which the concept could be used and the economic and logistical limitations for iron ore. The paper also looks at the risk assessment criteria to be applied in selecting the type of resource projects where the model could be applied successfully. Other aspects considered in this paper are the project planning requirements, technical and economic feasibility, bankability and operability. Reference is made to the operating experience of contractors at a number of sites and feedback from the resource companies as managers of the projects.CITATION:Connelly, D, 2013. Mobile crushing and screening plant applications for small- to medium-sized iron ore projects, in Proceedings Iron Ore 20 13, pp 349-354 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 12, 2013

By Madgwick J. C, Ralph B. J

A method for the determination of microgram quantities of uranium in leachates from low grade uranium ores is described. Solubilized manium is purified by transfer to an organic solvent by a selective solvent extractionprocedure using tributyl phosphate, iso-octane, and aluminium nitrate. The organic phase is mixed with scintillation fiuors in toluene and the radioactive decay determined in a liquid scintillation counter. The method is sensitive and reproducible in the range 3-30 µg uranium.

Jan 1, 1978

By Yindong Yang

Despite the importance and usefulness of basicity in metallurgical slags, the optimum quantitative expression of it has remained elusive, partly due to the fact that the precise concept of basicity has not been properly clarified. The two basic approaches to the concept of basicity are the Lux-Flood, which perceives basicity in terms of the activity of the free oxide ion, a O2- , and the Lewis, which perceives basicity in terms of the ability to donate negative charge. The former has been almost universally adopted in the area of metallurgical slags, while the latter has been increasingly accepted in the field of glass chemistry. In this paper, some difficulties of the Lux-Flood approach are pointed out, including the need for indirect measures of a O2- , which have proliferated in recent years. Accordingly, it is suggested that the Lewis approach has a good deal to commend it, and that the quantification of it in terms of optical basicity is the best measure of basicity available, which should therefore be more widely applied in metallurgical slags than it currently is. The fact that there are intrinsic problems in evaluating the optical basicities for the transition metal oxides is acknowledged, and a new scale is recommended. The patterns of iso-optical basicity lines in ternary systems are shown to agree well with the pattern of iso-activity and iso-capacity lines under appropriate conditions. * Originally published in the Proceedings of MINPREX 2000, published by The AusIMM.

Jan 1, 2001

By D Craw

The Old Man Range, south of Alexandra, in central Otago consists of a package of highly folded greenschist facies schist of the Wanaka lithologic association. The range is crosscut by several east to ENE-striking high angle gold-bearing quartz veins, (eg Whites Reef and Grays Reef), which were extensively worked in the late 1800s. The range is bounded on its east side by the Old Man Fault, which separates these rocks from generally flat lying and planar Caples Terrane schist. To the west of the Old Man Fault, about halfway up the range, a large subparallel, 100 m wide fault zone strikes NNW and appears to cut off the historic veins. The fault zone consists of highly sheared and folded rocks and numerous high angle cataclasites and centimetre-scale clay gouge zones. Hydrothermal alteration is not apparent and the individual faults and shears are clay altered, possibly due to weathering, without visible quartz veins. Gold, limonite pseudomorphs after pyrite and rutile are concentrated in some of the narrow cataclasites and gouge zones. These mineralised structures are texturally similar to the gold-bearing reefs and may be structurally related. It is postulated that the NNW-striking shear zone and ENE-striking veins may be a conjugate array formed during a period of Cretaceous normal faulting.

Jan 1, 2004

Development of a Froth Dropback Measurement Device

Sep 13, 2010

Microfluidic Solvent Extraction for Mineral Processing of Copper Leach Solutions

Sep 13, 2010

In 1953, Dr. N. H. Fisher of the Bureau of Mineral Resources, acting on behalf of the Society of Economic Geologists, which is considering the sponsoring of a uniform system of nomenclature for ore reserves, enquired from the Australasian Institute of Mining and Metallurgy whether it had ever considered this subject and particularly whether it had ever set up any standard definitions or specifications with regard to ore reserves.As this had not been done, but was thought to be desirable, the Council of the Institute appointed a Committee consisting of H. H. Dunkin, Associate, Professor of Mining Engineering, University of Melbourne (Convenor), E. A. Rudd, Professor of Economic Geology, University of Adelaide, I. N. Campbell, Chief Geologist of Western Mining Corporation; and the writer to consider and report on this supject.In December 1953, the Committee submitted its first report to the council and this report (reproduced here as an Appendix) was widely circulated among member companies, and engineers, with an invitation to comment on the proposal. A large number of, replies was received and studied.After studying the replies the Committee issued a second report in part as follows:-From these replies we have learned that the suggestions made in the first teport of the Committee are unacceptable to most of those interested, on one or all, of the following grounds;-(a) number of categories,(b) definition of categories;(c) nomenclature.

Jan 1, 1955

The emergence of China as a global economic power has not been without its birth pangs and the current coal market is testimony to this. Traditionally the coal market has been controlled by mature economies that functioned along balanced lines of supply and demand. The emergence of China and India as major forces in the international market has shifted this balance of power from mature economies to the developing economies of China and India. Of late Chinese Central Government policy has caused wide swings in the supply of Chinese coking coal and thermal coal to the international Asian markets. This has resulted in huge increases in demand for coal from producers in Australia, Canada, Indonesia, USA and Russia. Additionally since the late 1990s the liberalised Chinese economy has been growing by between nine to 12 per cent per annum. The corresponding rise in the standard of living of their 1.4 billion people has resulted in a strong demand for raw materials, initially met by domestic production and more recently met by the importation of raw materials including iron ore, oil, coking coal and thermal coal. Commensurate with this growth in China has been the emergence of India (pop one billion) as another major developing economy in the region. Whilst the Indian standard of living is lower than that of the Chinese, this subcontinent still has some 300 million people with middle class consumption demands. India is a major importer of oil, coking coal and thermal coal. It exports iron ore to China with growth parallel to China (seven to nine per cent per annum). These combined new demands from India and China have put unprecedented pressure on the global supply of coking and thermal coals. These pressures are reflected in the current world spot prices for coking and thermal coals which are at historically high levels. Whilst current demand from China and India is high it is anticipated that new projects will partially satisfy this increasing demand. Expectations are that overall thermal and coking coal prices will rise steadily. This paper seeks to identify the potential effects of Chinese and Indian economic growth on the international markets for coal.

Jan 1, 2004

By M Begbie, R J. Norris, D J. MacKenzie

The Otago Schist is crossed by numerous deformation zones that formed in the latter stages of metamorphism and uplift of the metamorphic belt. These deformation zones are long (tens of km) linear features at the regional scale, and are generally narrow (km scale or less). Many of these structural zones separate schist domains with different rock types and structural/metamorphic histories. The Hyde-Macraes Shear Zone is one such deformation zone, and this zone hosts the active Macraes gold mine. The Rise & Shine Shear Zone, 80 km NW of Macraes, is also enriched in gold and has been mined historically. Mineralisation in both these shear zones occurred during the transition from ductile to brittle deformation as the schist belt was uplifted from greenschist facies metamorphic conditions. Recrystallisation of quartz and micas in the early stages was overprinted by cataclasis, with sulfide and gold precipitation throughout. Many of the other late metamorphic deformation zones formed under similar greenschist to sub-greenschist facies conditions, with similar overprinting of recrystallisation textures and folds by more brittle textures such as breccias. Under these conditions, originally regionally pervasive deformation at the highest metamorphic grades was evolving towards more focussed high strain zones at lower temperatures and pressures. Shear zones initially focussed fluid flow along microshears and mineral grain boundaries, resulting in 1 to 100 m scale alteration and replacement in the host schist, with only local development of quartz veins. Fluid flow was not controlled by open fractures, and the rate of fluid movement was probably slow and pervasive. After uplift into the brittle regime, the schist belt underwent tectonic extension. Extension was accompanied by development of swarms of steeply dipping veins, with localised mineralised normal faults. Hydrothermal fluid flow throughout this uplift history was a normal consequence of late stage devolatilisation of the metamorphic belt. Hence, all late metamorphic deformation zones should be considered prospective for gold accumulation.

Jan 1, 2005

Sluiceboxes can provide a much higher concentration ratio than most other gravity concentrators (up to 50 000:1) at very high overall placer gold recoveries (greater than 99 per cent). They are also very reliable, inexpensive and simple to operate. This combination is very difficult to beat and explains why the sluicebox is still the most important placer gold concentrator in northwestern Canada, Alaska and the rest of the world. A sluicebox is a rectangular fl ume containing riffles on matting, through which a dilute (<12 per cent) slurry of water and alluvial gravel flows. Sluiceboxes are actually centrifugal concentrators with settling velocity playing a minor role in gold recovery. Due to their higher density, gold particles tend to segregate to the bottom of the slurry flow where they form a streamline that is diverted by a low pressure zone into a riffle. Under ideal conditions, this ribbon of slurry will be overturned as it flows down the rear of the following riffle and will continue fl owing in a circular path to form a vortex. At the bottom of this vortex, centrifugal and gravitational forces combine to drive gold particles into or beside the matting. To remove the gold concentrates, sluiceboxes are shut down and the riffles and matting are taken apart and cleaned. The slurry velocity provides the energy that powers the vortex. If the velocity of the slurry is reduced through overloading with solids, insufficient water flows or shallow gradients it may not sustain a full size vortex. If the riffles are too close, too far apart, too tall, or if there is not enough energy available to the vortex, the vortex will not be formed properly and gold recovery will be reduced. If the slurry velocity is too high, extreme turbulence and the resulting scouring will also cause gold losses. Testing sluiceboxes with conventional sampling and evaluation techniques is very costly, time consuming and problematic. Most placer gold ores contain a very small number of gold particles in a large volume of pay gravels. Sluiceboxes can lose coarse gold particles. The presence or absence of one of these particles in a tailings sample can lead to high unpredictable errors (nugget effect) even when large sample volumes are processed with care. Every time conventional samples are upgraded, additional errors are introduced due to the inefficiency of recovery equipment. Nuclear tracer tests are more accurate, faster, cheaper and safer than conventional sampling. In 1989 through 2002, the recovery efficiency of dozens of sluicing systems was determined by mixing radioactive gold particles (tracers) into the feed streams of dozens of placer mines in the Yukon Territory, British Columbia, Alaska and Guyana. Four distinct sizes of nuclear tracers were used and their recovery was related to the design and operational characteristics of the individual sluiceboxes and their pay gravels. At clean up, scintillometers were used to detect the very low level X-ray and gamma ray radiation emitted by these tracers and locate them in the sluice runs. The effectiveness of any given section of riffles was easily diagnosed by the presence or absence of tracers. At every mine the gravel feed rates, water flows, equipment dimensions and riffle performance were measured. After the gold tracers were removed from the fi nal concentrate and counted, the concentrate was sieved and weighed. These gold recovery, weight and sieve data were used to calculate the quantities and size distributions of the gold particles in the original pay gravels and those lost in the tailings. The expired tracers were stored in a lead lined container until their radioactivity was near background levels (about two months). The standard errors from these radiotracer tests were estimated from binomial probability theory with the equation: SE = {(n + p + q) ^ 0.5}/n. Where n was the total number of radiotracers added, p is the proportion recovered and q was the proportion lost. Each overall recovery estimate would be within one standard error of the true recovery value (14 times out of 20) and almost always within two standard errors of the true recovery (19 times out of 20). The maximum standard error with 100 tracers was five per cent and occurred when the recovery approached 50 per cent. With higher recoveries, standard errors usually ranged from one to two per cent.

Aug 1, 2010

By P N. Holtham

As part of a long-term study of titanium minerals processing being undertaken by the Julius Kruttschnitt Mineral Research Centre (JKMRC), techniques have been developed to measure the electrical properties of the various minerals. The measured values will be used to model the behaviour of the various minerals in high-tension roll and electrostatic plate separators. The resistivities of ilmenite, rutile and zircon from a number of Australian producers have been measured by applying a DC voltage across a test sample and measuring the resulting very small current flow. By appropriate design of the measurement cell and attention to the experimental procedure, reproducible resistivity values have been obtained, ranging from 106Ωm for ilmenite to 1013Ωm for zircon. However, the conditions of measurement are radically different from those under which electrical separation takes place. It is not certain that the measured values reflect the resistivities seen under high-tension separation, during which the particles are subject to a high intensity corona field. Consequently, an alternative technique for measurement of resistivity under conditions of corona bombardment has been developed. It is based on the experimental procedure of Castle and Yelle (1979) used to measure the resistivity of fly ash under the conditions occurring in electrostatic precipitators. This paper describes the development of the segmented ground plane measurement surface and a high-voltage switched resistor network which comprises the in situ resistivity apparatus. Results are presented comparing the measurements made under corona bombardment with those made using the DC measurement cell. The equipment has also been used to study the current distribution from a corona wire, as a function of high-tension voltage and wire-to-plane spacing.

Jan 1, 2001

Study on the Effects and Mechanics of Na2SO3 to Chalcopyrite and Galena

Sep 13, 2010

By A Priatna, H Rumbino, T Casten

This paper discusses the progress of the Deep Mill Level Zone (DMLZ) mine from the pre-feasibility study completed in 2005, through commencement of development access in 2008, completion of the feasibility in 2010 and cave initiation in late 2015. This fourth lift of caving in the East Ertsberg Skarn System (EESS) is located 500 m below the currently producing Deep Ore Zone (DOZ) mine and represents approximately half a billion tonnes of ore and around 1900 planned drawpoints, scheduled to be mined at a peak of 80 000 t/d.The paper reviews the mine design, access requirements, planned footprint sequence and major fixed facility installations such as ventilation, oreflow and shops. A discussion of the preproduction development and construction activities and some of the critical technical challenges overcome during this time frame are addressed, as well as the cave initiation process undertaken in late 2015 and the ramp-up of production and progression of caving.CITATION:Casten, T, Priatna, A and Rumbino, H, 2016. Deep Mill Level Zone – from feasibility to production, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 635–644 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016