Search Documents

By C Li, K McDonald an, T Nicholson, C Brown

The relative reactivities of chars prepared from different coal samples at temperatures in the range 500 to 1150¦C were determined by measuring the rates of metallisation of a standard ilmenite concentrate. The results have been interpreted in relation to different measured physical and chemical properties of the chars. Char reactivities were found to correlate with the maximum specific surface area (SSA) of the chars, obtained from plots of SSA versus temperature. Weathering of coal samples gave higher reactivities which correlated with higher SSAs. Experiments using recycled chars showed that the high internal SSAs developed during earlier reduction reactions provide no benefit in terms of increased metallisations. The important role of char hydrogen contents in controlling low temperature metallisation rates was demonstrated. Chars prepared from different rank coals had the same hydrogen content when prepared at the same temperature. Ilmenite metallisation rates had a linear dependence on the hydrogen content of the chars. Large differences in the slopes of the metallisation versus H2 content curves for different chars were interpreted in terms of SSA variations and catalysis of the gas reactions by dispersed metallic iron particles in the chars. A simple test based on magnetic separation of the char was shown to give an indication of enhanced reactivity due to contained metallic iron.

Jan 1, 2001

By M Lovitt, T Hewitt

The extraction of drawbells in Lift #2 at Northparkes Mines E26 orebody was achieved by single shot blasting, enabled through the use of electronic detonators. This paper discusses the designs considered at the time of the feasibility study and the various changes made to these designs prior to and during the construction phase of the Lift #2 block cave. Operational issues encountered are highlighted, as are ways in which these were overcome. The amount of personnel utilised to mine the drawbells is also covered. Lists of design and operational considerations to be used for drawbell extractions have been included.

Jan 1, 2005

This paper covers only the energy uses of natural resources and does not deal with non- energy uses, which in 1975 were of the order of 10 per cent of the total consumption of energy resources. The United Nations `J' Series of Statistics ex- presses each of the various forms of energy in terms of its coal equivalent in metric tonnes and this basis is followed in this paper. One tonne of black coal (referred to as tce) has been taken as the equivalent of the following. 29 X 109 joules or 27.5 X 106 Btu 0.68 tonnes or 4.8 barrels of crude oil 750 cubic metres or 26.5 X 103 cubic feet of natural gas 1 ò5 to 3.3 tonnes of peat or lignite (world average 2.54; Victorian brown coal 3 0) 8055 kWh (at 3.6 X 106 joules or 3412 Btu per kWh at 100% efficiency) 2660 kWh at 33% efficiency of generation 50 grams of uranium present in natural uranium reactors (see note later under nuclear energy) 0.8 grams natural uranium in breeder reactors Nuclear and hydro electricity are expressed as the coal equivalent required to produce, at 33 per cent efficiency, the same amount of electricity. In other words, electricity produced by these sources is converted to its coal equivalent at the rate of 2660 kWh = 1 tonne coal.

Jan 1, 1978

By Falbo A, Quarestima S, Cozza C, Barbaro M

A new synthetic reagent of the mercaptobenzoxazole class, 5- methyl-2-mercaptobenzoxazole, has been studied. This reagent exhibits powerful selective collecting action towards copper sulphides present in several complex ores, as demonstrated both by laboratory and pilot plant tests. Industrial production is expected to start in the near future. The way this reagent reacts with pure chalcocite has been studied utilising in situ FTIR techniques, adsorption tests, electrokinetic potential measurements and Hallimond cell flotation tests. The FTIR studies have indicated the nature of the surface phase. Adsorption isotherms obtained by the rest method have revealed the quantitative evolution of surface products, permitting the determination of surface coverage at various reagent concentrations. The electrokinetic potential has been utilised to verify the stability of individual species in diverse concentration ranges. Correlation of the results obtained has provided indications on the chemical interaction of this reagent with the surface and on the surface Arrangement.

Jan 1, 1993

By Harada M, Katsuta S

In order to shorten the time taken to com- plete shield tunnel excavation work, reduce labor costs and to improve safety, an automatic assembly robot system for the segments used has been developed. It was developed in the three years from 1982 until 1984. An experimental assembly system for concrete segments (outer diameter:.3.55m) has been thoroughly tested to confirm that these segments can be fed and assembled automatically (Fig. 1, 2). This report outlines the robot which will be put into practical use in the near future. The robot senses the position of already assem- bled segments by means of position sensors, controls the position and the attitude of the segment to be assembled to allow bolt hole positioning, and completes the automatic assembly of a se;nent by automatically tighten- ing bolts. The six segments which make up one ring can be automatically assembled in about 25 minutes.

Jan 1, 1987

By B Ganesia, H Sahupala

PT Freeport Indonesia is a copper-gold mine operation located in West Papua, Indonesia about 3500 km east of Jakarta. Current ore production is about 270 000 tpd, of which 30 000 tpd comes from underground. In the future, the production from underground will be gradually increased to reach a maximum of 115 000 tpd, as the Grasberg open pit production decreases. The current and future challenge for PT Freeport Indonesia is to fill the quota of underground miners, as Indonesia does not have a long culture of underground work. At present, there are only three active underground mines in Indonesia. The lack of underground skilled labour incited the company to develop its own skilled workforce. In the mean time, to overcome the shortage of personnel, the underground management had to find a way to improve the productivity. Since 21 May 1998, PT Freeport Indonesia Underground Mine has operated with the new roster of two rotating shifts a day, 11 hours per shift. The previous schedule consisted of three nine-hour shifts per day, six days a week, for a total of 26 working days in a month. This change was intended to increase the productivity of the miners. With the previous roster, studies determined that the effective working time was only seven hours per shift. The new roster produces an improvement of effective working hours to about nine hours per shift. As a result, total production has increased by 33 per cent and the utilisation of production equipment has increased by 16.5 per cent. This paper describes the background of the decision to change the work schedule, the study carried out to evaluate the benefits and drawbacks of the new shift roster, the challenges, and then compares the results for various parameters between the old schedule and the new one.

Jan 1, 2002

By B Levasseur, C Olsen, E Ghasemian Langeroudi, F Larachi, F Safizadeh, C Gagnon

Gold recovery by the cyanidation process is often accompanied by the leaching of other species. This leads to the depletion of the level of free cyanide and oxygen available for gold cyanidation. The largest proportion of the consumed cyanide is diverted by the cyanicides (eg S, Cu, Zn, Fe, etc) into non-valuable complexes.COREMÆs Extractive Metallurgy team has been conducting a research program on the improvement of the gold cyanidation process. As a part of this program, the current study aims to investigate the effect of certain operating parameters on the reactions involved during preoxidation and cyanidation. Flotation tailings and single mineral samples such as pyrite, sphalerite and chalcopyrite, along with their different combinations, were analysed to highlight the influence of ore mineralogy on the operating conditions. The effects of different kinds of oxidants (oxygen, hydrogen peroxide, ferricyanide and ozone) and chemical additives (ammonium sulfate) were investigated.Experiments conducted in alkaline solutions reveal that mineralogy is a key parameter since pyrite, chalcopyrite and sphalerite react quite differently during preoxidation and cyanidation. A significant increase in sulfur dissolution, especially on pyrite, was observed by applying preoxidation. H2O2 preoxidation showed a positive effect on increasing sulfate formation, a desirable by-product from the cyanide consumption point of view. Preoxidation of synthetic ores with ferricyanide resulted in boosting thiosulfate formation. Tests conducted on flotation tailings from a polymetallic mine revealed that a short preoxidation increases the dissolution of the ore leading to higher gold recovery and lower cyanide consumption. Regarding the formation of thiocyanate, the most undesirable by-product of the cyanidation, ferricyanide and ozone were found particularly efficient to hinder their formation. Finally, the addition of ammonium sulfate during the cyanidation process showed some promising results in terms of both gold dissolution and cyanide consumption.CITATION:Ghasemian Langeroudi, E, Levasseur, B, Safizadeh, F, Olsen, C, Larachi, F and Gagnon, C, 2013. Optimisation of operating parameters for cyanidation of sulfide-bearing gold flotation tailings in order to prevent the impact of cyanicides, in Proceedings World Gold 2013 , pp 111-120 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

Safety and health at work is about people. It is about people who plan for work, organise work and perform work. It is about those who come in contact with the workplace and those who are responsible for the workplace. There are wider ranging safety and health obligations that are imposed on the industry stakeholders that span all phases of the production process. In all cases, those responsible for discharging the obligations must ask the questions: Is what we propose safe?, can it be done safer? and are we sure? What we learn from recent legal cases before the courts is that it is essential that all stakeholders work together in a collaborative way when discharging these obligations. Safety and health at work cannot become an issue that is viewed only through the eyes of a single stakeholder group. The reason for this is quite simple. The interrelatedness of the responsibilities that are imposed on each of the stakeholder groups, means that the performance based legislation simply wont work, where an active model of communication and consultation is not in place.

Jan 1, 2005

By M Pernechele, U König

Most of the operating steelmaking capacity currently relies on conventional, coal-based steelmaking processes. Currently, direct reduced iron (DRI) is only produced in regions where energy is available at low cost. To align with net-zero emissions goals, steelmaking capacity must transition to loweremissions steelmaking technology. Direct reduction of iron ore will get one of the preferred methods in the future due to its high technology readiness. New reduction technologies include hydrogenbased direct reduction processes. To ensure optimal efficiency during DRI production and to cope with newly developed technologies, processes need to be monitored more frequently and accurate. Traditionally quality control of raw materials and DRI has relied on time consuming physical testing, wet chemistry or the analysis of the elemental composition. The mineralogy of DRI that defines its properties is not frequently monitored. Process monitoring and quality control of DRI is possible by using modern X-ray diffraction (XRD) methods. In addition to the metallic iron content (Femet), metallisation (Metn) and the total carbon content (Ctot), XRD analysis also identifies the overall mineralogical phase composition. This allows additional information about the reduction process and enables fast counteractions on changing raw material mixtures. The benefits of the quantitative determination of the phase composition and the calculation of process critical parameters to produce DRI will be demonstrated with a case study

Sep 18, 2023

By D J. Thobaven

Project financing challenges caused by declining commodity prices have heightened the need to improve project metrics such as minimising capital payback and maximising net present value (NPV). Khnaiguiyah Mining Company (KMC) recognised the need to improve early cash flows at their Khnaiguiyah zinc-copper project after initial studies showed the project could not provide the desired financial outcomes necessary to compete for investment dollars in the current market.A significant improvement to the project cash flow in early years was realised through simultaneous optimisation of cut-off grade, mining sequence and strategic stockpiling. This improvement was achieved by accelerating mining in the pits, stockpiling lower value material and feeding higher value material directly to the plant. The schedule required higher mining and stockpile capacities than the sequential mine plan although minimal change occurred in the definition of ore and waste as measured by tonnes and grade. The practicality of the strategic schedule was demonstrated by implementation in the production plan with excellent conformance.CITATION:Thobaven, D J, 2014. An application of simultaneous optimisation – improving the payback period of a zinc-copper open cut project, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 137–144 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Grano S. R, Ralston J

It is the perennial problem most metallurgists face when examining data collected from laboratory float tests and plant surveys - there are more numbers than we know what to do with! The objective of this paper is to analyse and interpret a set

Jan 1, 1994

By J Seppelt, B Akerstrom, J Bubnich, D Seaman, T Waters

The Cadia Hill concentrator at Newcrest’s Cadia Operations has undergone several modifications and upgrades to treat an increased throughput rate of harder ore from the Cadia East block cave mine.Subsequent to the commissioning of the expanded circuit, the flotation cleaner block has undergone a systematic optimisation programme tackling all facets of circuit operation. This included debottlenecking circuit constraints and installation of Jameson cell technology to enhance copper and gold recovery while rejecting fluorine and gangue from the concentrate.This paper outlines the improvements over the course of the project and results obtained from the implemented actions.CITATION:Akerstrom, B, Seppelt, J, Waters, T, Bubnich, J and Seaman, D, 2018. Cleaner circuit optimisation at Cadia Operations, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 457–476 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

The character of alluvial gold deposits presents severe difficulties, and sometimes limitations, on the extent to which metallurgical efficiency can be measured. Very little monitoring of metallurgical performance is practised. An indication of performance is often extracted from the comparison of production to the estimate. This is a dubious practice. The recovery efficiency of conventional practices, viz sluices, tables and jigs, falls off sharply below 0.2 mm. Field evaluation procedures tend to simulate these conventional practices. Thus the presence of fine gold may not be detected, particularly if obscured by clay. There is increasing evidence that fine gold could, in places, be present in sufficient concentrations to be economic. Most gold in paleoplacers is finer than 0.1 mm. There are established practices elsewhere in the mineral industry that may physically recover gold down to 5 microns in size and which could find application for fine alluvial gold.

Jan 1, 1984

By K Peters, C McKenzie

New Zealand has an established history of gold production beginning with the gold rushes of the 19th century in the Coromandel, Nelson/Marlborough, West Coast and Otago regions. Despite this, the number of significant modern hard rock gold operations has been limited in recent years due to a lack of sustained exploration capital and not limited geological prospectivity.The New Zealand Government is actively encouraging explorers to invest in New Zealand through a series of targeted promotional visits, more importantly through the acquisition of precompetitive regional geophysical data. Data collection has been completed over the prospective Northland epithermal district and a large portion of the South IslandÆs west coast that is prospective for both orogenic gold and intrusive related gold.Analysis of new data has been an important component in aiding the generation of exploration targets from prospectivity modelling. Determining the prospectivity of an area involves reviewing all the available data and analysing it with respect to the most up-to-date mineral system model for the mineralisation style of interest. Using the weights of evidence modelling approach, the most prospective areas for epithermal gold-silver, orogenic gold and intrusion-related gold have been identified. The key exploration parameters relevant to each mineral system are first represented spatially and then statistically combined into a single prospectivity map. New potentially economic deposits could be found by focusing exploration on targets identified from these models. The prospectivity modelling approach can greatly reduce the risk involved in mineral exploration.CITATION:Peters, K and McKenzie, C, 2013. New Zealand gold potential - using mineral prospectivity modelling to evaluate gold-bearing mineral systems in an underexplored country, in Proceedings World Gold 2013 , pp 479-486 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 26, 2013

By R R. Anand

Recent research by CRC LEME from an Australian mineral exploration perspective, has focussed on regolith architecture and mechanisms of geochemical anomaly formation, within transported regolith. Methods have been developed for the rapid production of regolith-landform maps which is the starting point for understanding regolith architecture in the third dimension. Methods for development of 3D regolith models are less well advanced, and require integration of all available geological and geophysical datasets, but still with a heavy reliance on drill-hole information. The base of the transported regolith û the unconformity û remains the most important regolith boundary for geochemical sampling in transported regolith terrains. A new generation portable spectral logger, employing a broader spectrum can interpret important features from drill chips within the regolith. This allows internal architecture, redox fronts and the all-important interface to be objectively identified. Transported lateritic components can provide vectors to mineralisation in depositional regimes. Palaeomagnetic and new radiometric methods which date individual phases of the regolith provide evidence of different episodes, each characterised by different geochemical dispersion patterns in transported regolith. Along with lateritic residuum, calcrete is prime sampling medium. Calcrete is probably enriched in gold through physical and biological processes, rather than straight chemical processes. In South Australia, the lowermost calcrete layer buried within the depositional regime, especially where it lies directly over the silcrete layer at the buried interface, is the desired sampling medium. Certain gum trees, with deep roots in transported regolith have been shown to record anomalous values of gold and basemetals in leaves, twigs and bark. Anomalous metals in acid-sulfate soil seeps can also provide a window through sedimentary cover in respect of mineralisation in the basement. A number of Yilgarn occurrences of gold anomalies in transported cover, strongly infer hydromorphic and biological mobilisation of gold. This inference is supported by micro-analyses of regolith mineral hosts in hardpans and mottled sediments, which show gold and pathfinder elements prefer to reside in goethite and specific types of clay minerals. This creates anomalies in specific mineral phases. However the inference that that these are sites of mobile or labile metal ions remains enigmatic. Similarly there is inconclusive evidence that selective extractions will provide an anomaly not otherwise detected by conventional total dissolution methods. Hydrogeochemistry is a promising exploration tool for basemetal exploration. The importance of microbes in both the dissolution and precipitation of gold in the Australian regolith is demonstrated. We are on the verge of identifying the functional gene sequence of individual active microbes. A consideration of possible mechanisms for creating anomalies in soils above transported regolith, presents difficulties in facilitating upward movement of ions from the watertable to the surface. Perhaps the best avenues of research lies with surrogate soil gases, and biotic transfers.

Jan 1, 2004

By J M. Shekiro

In the chloride process to manufacture TiO2 pigment, feedstocks containing higher TiO2 contents (high-grade ores or HGOs) are favoured in order to minimise production of undesirable by-products. Most of today’s HGOs are produced through the smelting or reduction and leaching of ilmenite, processes which consume significant energy and/or produce large volumes of non-titanium materials that may have to be landfilled. In order to improve the economic and environmental sustainability of its TiO2 business, the DuPont Company, working with Kobe Steel Ltd, has developed an innovative process called TiRON for making HGO. Using a rotary hearth furnace, the process reduces ilmenite to a high TiO2 slag and metallic iron granules. The TiO2 slag is suitable for TiO2 pigment manufacture, and the iron is suitable for steel making. TiRON can process sand or rock ilmenite of varying compositions and particle sizes. Fossil fuel instead of electricity supplies the energy for the reduction. Dusts and off-spec materials are recycled. These process attributes, together with capital requirements estimated to be significantly lower, give TiRON substantial economic, environmental, and process flexibility advantages over conventional ilmenite upgrading processes. TiRON has been demonstrated at the semi-works scale, and preparations are being made to bring it to the pilot scale.

Oct 5, 2011

By May J. R

Exploration, including research, has fuelled the enormous expansion of the Australian mineral industry in the last three decades. Analysis of success and failure in exploration and research has therefore potentially powerful lessons and messages which may be used to influence the future shape and direction of the mineral industry. Research has been an integral part of organised corporate mineral exploration since its beginnings in Australia in the 1930s. In corporations, the activity generally called project generation or new project development is the main expression of exploration research but mostly it goes unidentified and poorly documented except perhaps when a successful discovery is made and reported on. The competitive nature of exploration means that extended and detailed analysis of corporate exploration research across the industry is impossible to achieve.

Jan 1, 1992

By G M. Zhomin, A S. Arkhipin, A Kondratiev

Viscosity of multicomponent slags is one of the crucial physicochemical properties for many industrial processes and technologies. While the viscosity-temperature relationship of completely molten slags can well be described by an Arrhenian-type law, the compositional dependence of viscosity is still not fully understood, especially in compositional regions with the lack of experimental data (eg at the glass-former concentration of 90 molar per cent or higher). In the present work major compositional relationships of the activation energy of viscous flow have been revised for numerous binary and ternary slag systems on the basis of experimental data collected and stored in the viscosity database OxiVis. For example, it has been found that the activation energy relevant to the polymerisation effect in binary systems of the MO-GFO type, where MO is the modifier oxide (ie monovalent K2O, Na2O, Li2O and bivalent CaO, MgO, BaO, MnO, PbO etc) and GFO is the glass-forming oxide (SiO2 or B2O3) is not always proportional to the third power of XGFO (contrary to the Urbain formalism) and can vary significantly dependent on the slag system. Also, the activation energy of the charge compensation effect has been revised for ternary systems of the AO-MO-GFO and AO-MO type, where AO is the amphoteric oxide (Al2O3, Fe2O3 or other). A simple polynomial model has been proposed on the basis of the carried-out analysis for estimation of viscosities of multicomponent slag systems. The model has been optimised against the experimental viscosities in the selected binary, ternary, and higher-order oxide systems and has been shown reasonable agreement with the experimental data.

Aug 21, 2024

By J P. Sykes, A Trench

"World-class mine projects are increasingly failing to become world-class mines. Non-technical, socio-political and environmental problems seem, in part, to be the cause. However, the intangible and qualitative nature of these problems means overcoming them will require a greater systemic understanding of how the various technical and non-technical factors interact. This is particularly important as the concept of sustainable development has changed the industry paradigm sufficiently that it is no longer clear what world-class means. Finally, this better systemic understanding of mine projects needs communicating back to the exploration sector to improve exploration targeting.However, a disconnect between the exploration and mining sectors and between geologists and mining’s other professional disciplines means this is currently not possible. The use of economic evaluation techniques to assess the risk and value presented by the various technical and non-technical factors can assist with this by giving the varied professions a common language and including inputs from all disciplines. This paper therefore suggests a theoretical framework for analysing the various technical and non-technical factors, particularly the most challenging intangible and qualitative ones, and incorporating them into the typical economic evaluation techniques used in the mining industry.Understanding the risk and value relating to both technical and non-technical risks, however, places a greater emphasis on mining geologists to be conversant with a wide range of disciplines. Mining geologists will have to develop three types of knowledge:focusedinter-disciplinarybroad. In addition, they will have to become systemic thinkers to connect these types of knowledge. This multidisciplinary approach will require the use of fundamental critical thinking skills, common sense, intuition, experience and quantitative modelling techniques, dependent on the situation. As a result, both companies and professional societies, such as the Australasian Institute of Mining and Metallurgy, will have to develop ways of improving mining geologists’ inter-disciplinary and broad knowledge.CITATION:Sykes, J P and Trench, A, 2014. Resources versus reserves – towards a systems-based understanding of exploration and mine project development and the role of the mining geologist, in Proceedings Ninth International Mining Geology Conference 2014 , pp 243–270 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Aug 18, 2014

By Hoberg H, Schneider FU

The stability of suspensions can frequently be controlled only by the use of supplementary polymeric agents. Such methods date back to the time of the ancient Egyptians, who used natural rubber as a deflocculant for carbon black in the manufacture of ink (Anon, EncyclopediaBritannica, 1968). Since the development of synthetic polymers in the 1950s they have been deployed in all manner of applications. Indeed the mining and paper industries as well as industrial or communal waste water treatment plants are largely dependent on flocculants which make a major contribution to the relief of the environment. As some of the polymers used are carried out from the process via purified water, problems can emanate from the application itself as long as no reliable data is available as to the exact whereabouts of the polymers and their impact on the biosphere. In order not to invade other systems, they would have to be biologically degradable which has not, until now, been confirmed (Blockhaus, Sequaris and Schwuger, 1991; Schumann, 1991). It has, however, previously been demonstrated (Hoberg et al, 1990) that when process water circulates in mineral processing operations, residual amounts of polymeric flocculants can have extremely adverse effects on the selectivity of flotation processes. The adsorption behaviour is consequently one of the most important considerations in the development of new polymers, the aim being to minimise the amount of non-absorbent matter. The objective of the investigations carried out on ampholitic synthetic polymers of high molecular weight to be reported on here was to permit the connection between settling index and adsorptivity to be characterised in greater detail. As the level of knowledge concerning flocculation and polymer adsorption in real systems is still limited in spite of numerous practical and theoretical studies in this field, the experiment was designed to be relatively broadly-based. As well as investigating various raw materials, an attempt was made to compile results on the influence exerted by different surface charges.

Jan 1, 1993