Search Documents

By H. A. Hancock, L. M. Pidgeon

Equilibrium carbon monoxide pressures were measured over the reaction between chromium oxide and a number of solid ferrochromium alloys in the composition range 0.4 to 4.8 pct C and 0 to 49 pct Fe. Measurements were also made for the carbides Cr23C6 and Cr7C3 which agreed well with previous investigations. Between 1050°and 1400°C the pvessures varied from 0.1 to 56 mm and increased markedly with the iron and carbon contents of the alloys. The data were used to estimate the activity of carbon in the alloys and to calculate the equilibrium conditions for the decarburization of a useful range of ferrochromium alloys. WHEN ferrochromium is produced by the reduction of chromite with carbon in an electric arc furnace it invariably contains up to 10 wt pct C. For many purposes such as the production of stainless steel, it is necessary that the carbon content be as low as from 0.02 to 0.05 pct. Thus an important part of the ferrochromium industry consists of the production of low carbon ferrochromium. The classical Bessemer steelmaking technique cannot be used to oxidize low carbon contents in chromium and ferrochromium alloys without also oxidizing the chromium. Recently a new commercial process2-4 has been introduced for oxidizing carbon from high chromium content alloys which consists of heating the solid alloy with such oxidizing agents as Cr2O3, Fe2O3, or SiO2 in a retort at reduced pressures. By maintaining the carbon monoxide pressure below the equilibrium value for the system, the carbon can be removed as carbon monoxide without oxidizing the chromium. The equilibrium conditions for the decarburization of solid chromium carbon alloys have been determined by Boericke5 who measured the carbon monoxide pressure over the reaction between the various chromium carbides and chromium oxide. A typical reaction is shown below. Cr23C6 + 2Cr2O3 =u 27Cr + 6CO [1] These values are not applicable to the decarburization of commercial ferrochromium alloys which invariably contain major amounts of iron. The present investigation was therefore undertaken to measure the change in the equilibrium carbon monoxide pressure brought about by additions of iron to the Cr-C-0 system, thus extending the work of Boericke into the region of the production of low carbon ferrochromium. MATERIALS AND METHOD Materials. Measurements were made on two carbides of chromium, Cr233C6 and Cr7C3, and fifteen Fe-Cr-C alloys. The chromium carbides were made

Jan 1, 1963

By Y. L. Yao

It is suggested that the binary alloy systems of transition metals may be classified into groups according to "excess energy"E. For systems with positive ?E, the Laves phase, the TiNi3-, the TiCu3- and the Cudu-type rich in the smaller atom and the TizNi-type rich in the larger atom may exist. For systems with negative ?E and composed of two components of different crystal structures, the X, the Cr3O and the phase may exist on the side of the phase digrattz rich in the component with the higher "solubility factor" value am! the Cudu-type and the disordered hcp phase on the other side; if the crystal structure of two components is the same, the Cudu-type may exist on both sides. For systems with weakly positive ?E and cotnposed of different crystal structures, the u phase and the MgCd3-type may replace the Laves phase and the other types; the X, the Cr3O and the a phase may also exist. Finally, the equirnolar compounds of the CuAu- and the CsC1-type may exist irrespective of the sign of ?E. THERE are many factors which play a major role in the formation of binary intermediate phases in alloys, such as the crystal structure, the electronic structure, the atomic size and the electrochemical factor. To find the simultaneous effects of all these factors on the formation of intermediate phases of every metal would be a difficult task, especially because only a small fraction of experimental facts necessary for the complete formulation is known at present. Thus the past surveys of intermediate phases have been usually confined to few metals, several types of intermediate phases and some but not all controlling factors. In a previous paper1 the idea of "solubility factor" of metals was introduced. Although the suggested values are tentative and empirical, the formation of a continuous series of solid solutions in metals could be correlated with the interplay among the atomic size factor, the solubility factor and the crystal structure factor. The purpose of this paper is to demonstrate qualitatively the interplay of these factors in the formation of binary intermediate phases among transition metals. FACTORS CONSIDERED The Crystal Structure Factor. With rare earths excluded, the transition metals are classified into three common crystal structures listed in Table I. There is arbitrariness in the present classification of several allotropic elements. However, out of seventy-odd continuous solid solutions formed among transition metals, only six of them, namely, those

Jan 1, 1962

By Harry M. Mikami, Harold A. Heiligman

The term chromite is often used to cover all chrome ores and concentrates which are the designations actually employed by most industrial users and producers. Chromite is, of course, the predominant mineral in chrome ores which are aggregates of chromite and gangue minerals, most commonly magnesian silicates. Most chrome ores now used are petrographically chromitites which is a rock, rather than an individual mineral term. The title of this chapter, following past usage, is meant in the broad sense. Chromite is the only primary commercial source of chromium. This book is intended to deal only with nonmetallic minerals and rocks. Chromite uses are both metallic (ferroalloys) and nonmetallic (refractories and chemicals), but any discussion of mineralogy, geology, and mining is common for all types. A number of the major commercial ores are interchangeable, and their uses are determined by economic considerations. Mineralogy COMPOSITION [Chromite is a term embracing a wide range of chromium-bearing spinel*-group minerals the compositions of which can be expressed as (Mg,Fe2+)0.(Cr,AI,Fe3+ )203.t This can be further generalized to R2+O.R23+03 and the molecular RO: R,03 ratio is generally close to one. The exact composition may be arbitrarily expressed as a solid solution of six end-members, MgAI2O4, MgCr2O4, MgFe2O4 FeCr2O4, FeA12O4, and Fe2+.Fe23+04 with the proportions of each stated or plotted in the six-cornered prism of Johnston and Stevens61 or this scheme may be simplified to comprise only three endmembers making up a composition triangle, Fig 1. [ ] FIG 1-Triaxial composition diagram showing molecular compositions of chromites listed in Table 1. The RO.Fe2O3 corner includes Ti02 norms listed in the table. Note that the high-alumina chromites (1, 2, 3, 9), form a cluster well apart from the high-Cr2O3 chromites. There is a tendency for high-iron chromites to be higher in Fe2O3 + TiO2 but it is not a consistent or systematic relationship. The MgO/RO ratio must also be known to characterize the chromite chemically. Simplest and most convenient method is Thayer's' in which a chromite such as (Mg.65Fe.352+)O.(Cr.40Al.50Fe.103+)203 would be written as (Mge,) Cr eAlo. The molecular pro- portions of ferrous and ferric oxides can be seen at a glance as the divalent and trivalent oxides]

Jan 1, 1960

By A. K. Jena, M. O. Bever

The thermodynamic behavior of dilute solutions of copper, silver, and gold in liquid tin is not explained by current solution theories.1-3 The relative partial gram-atomic enthalpies, or heats of solution, of silver, gold, and platinum in liquid lead at 623°K have been measured in the investigation reported here. Their interpretation requires a modification of the regular-solution theory although lead-rich solutions may be expected to be simpler than tin-rich solutions. The liquid metal solution calorimeter used has been described.4 At the start of a run the bath consisted of 621 g of reagent-grade lead. Several calibrating additions of lead were made during a run; a value of 3.48 kcal per g-atom5 was taken for H623°K - H273°K Two runs were made with each of the solutes silver, gold, and platinum. Annealed wire samples of 99.999+ pct purity were used. Four to six samples each weighing 0.5 to 1,0 g were added from 273°K to the bath at 623°K and the associated heat effects were measured. The samples dissolved in approximately 3 min. No serious experimental difficulties were encountered. The heat effects of the additions in a run plotted against the average atom fraction of solute before and after each addition314 were linear functions of the concentration in lead of silver, gold, and platinum, respectively. By subtracting the difference between the heat contents of a solute element at 623° and. 273°K5 from the measuredheat effects, the partial gram-atomic enthalpy relative to the solid solute was obtained. The relativ: partial gram-atomic enthalpy at infinite dilution and the concentration dependence of the partial gram-atomic enthalpies obtained from the plots of vs atomic fraction x are listed in Table I. The relative partial gram-atomic enthalpy at infinite dilution of silver in lead of 5.46 kcal per g-atom at 623°K compares with values at 723°K of 5.74' and 5.765 kcal per g-atom. These data yield a temperature coefficient of 3.0 cal per g-atom-OK. The partial gram-atomic enthalpy at infinite dilution of gold in lead at 623°K is 0.89 kcal per g-atom compared with 0.85 kcal per g-atoms (obtained by extrapolation) and 0.95 kcal per g-atom.5 By combining these values for 623°K with those for several other temperatures5" the temperature coefficient of was found to be 3.2 cal per g-atom-OK. No thermodynamic data are

Jan 1, 1968

By P. C. Claspy, P. H. Smakula

The electro-optic coefficients of LiNbO, and KTao.,5Nboe3,O3 (KTN) have been experimentally determined at the HeNe laser wavelengths of 0.6328, 1.15, and 3.39 µ. The coefficients were calculated fronz the retardation induced by an applied electric field. The retardations were measured by observing one or move transmission maxima and minima as a function of the applied field, and by measuring the retardation directly with a Babinet-Soleil compensator. The values obtained agree quite well with those previo~lsly reported by others. Extinction ratios as high as 3000:l have been observed. Resistivities and Curie temperatures have also been measured. Light-induced optical inhornogeneities in LiNbO, repovted by others have been observed. CONSIDERABLE interest has recently been shown in the electro-optic properties of LiNb03 (Refs. 1 and 2) and KTN.3, 4 These crystals have a number of advantages over such well-known materials as KDP. These advantages include: 1) the infrared transmission of KTN and LiNb03 extends to 5 p whereas that of KDP cuts off at 1.5 p ; 2) driving voltages required for modulators using these materials are considerably lower than those required for KDP. After first discussing some theoretical considerations of the electro-optic effect, we will report the results of measurements of the dc electro-optic coefficients of these materials at wavelengths of 0.6328, 1.15, and 3.39 p. THEORY The generalized equation for the electro-optic effect can be written: Although lattice polarization is the fundamental variable, rather than the applied electric field, we follow the convention of expressing the linear electro-optic effect in terms of the applied field. For LiNbO the quadratic terms are negligible. Since KTN has a center of symmetry the rijk tensor is 0. After applying the usual symmetry considerations and index contractions,* the rijk and gijkl tensors can be expressed as follows: LiNbOaT If field directions are now chosen, the change in refractive index and the angle between the induced optic axes and the crystallographic axes can be found. The induced rotations of the principal axes of the index ellipsoid for fields in principal crystallographic directions are given in Table I. Since KTN is initially isotropic, the principal axes in the zero-field condition are parallel to the crystallographic axes. The induced retardations are given in Table 11. EXPERIMENTAL We obtained the various electro-optic coefficients by measuring the induced retardation as a function of

Jan 1, 1968

By A. S. Joy

Vacuum flotation tests carried out according to the method of Schuhmann and Prakash1 have shown that the acid limiting edge of the flotation area for a Brazilian hematite, in the presence of dodecylamine, is a straight line of slope approximately unity. The flotation tests and the structure, surface ionization, and electrokinetic properties of this hematite have been fully discussed elsewhere. 2 The numbers of adsorbed H+, and OH- ions and collector molecules have been determined in the range of critical conditions defining the acid limit of the flotation area. The total amine adsorption is shown in Fig. 1 as a set of contours superimposed on the straight part of the flotation area. These were determined by spectro-photometric estimation of the complex formed between residual amine and the anionic dye Orange II.3 The ionic strength of the solutions was kept constant and at a value in sufficient excess of the amine concentration to ensure that the diffuse part of the double layer was populated predominantly by indifferent ions. Adsorption of H+ and OH- in the absence of amine was found by potentiometric acid-base titration in the presence of hematite.4 The form of the adsorption-titration curves suggested that the hematite surface behaves in an amphoteric manner, and that positively charged sites arise through loss of a hydroxyl ion, and negatively charged sites by loss of a hydrogen ion. On this basis, curves 8 and 9, shown in Fig. 2, were calculated from the titration curves. These show the variation of the numbers of positive (s +) and negative (s—) sites with pH. To distinguish between ionic and other modes of adsorption, zeta-potential determinations have also been made using the streaming potential technique. The influence of amine on the zeta-potential of the mineral over a wide pH range is shown in Fig. 3. The change in charge ?s, due to adsorption of amine ions in the Stern layer, was calculated by applying the Gouy-Chapman theory, as modified by Stem, to the results shown in Fig. 3. The validity of this treatment has been shown by Ottewill and Jaycock.5 The three full lines, Nos. (1) through (3), included in Fig. 2 show the relationship between ?s and pH at three amine concentrations. The general conclusion from the zeta-potential curves is that adsorption of amine causes a reduction in the negative charge on the surface. Comparison of the values shown in curves (1) through (3) of Fig. 2 with the - curve shows that the magnitude of the reduction is comparable with that of s - at any given

Jan 1, 1964

By Joseph M. Jacisin

Fatigue tests were conducted on 2017-T4 alumium in alloy in an u1lrcthig.h vacuum of 2 x 10-lo Torr and in air. The vatio of vacuum-to-air faligue life for this ~malerial varied Jrom 3.5:1 at a strain of 2.5 X 1O-3 ill. pegr in. to 8:l at a strum of 3.3 x X ill. per 171. Sotlze pvelivtlinary data were also obtained on the faligue life of the alumirnum alloy in a dvy-nitrogen atmosphere. A dark deposit observed on the fracture surfaces of the aiv-tested specimens was identified as oxides of tr~angarzese and magnesium This observalion, and the close correlalion betaveen results obtained in vaCuum and dry-nitrogen environtments, tend to confirm that air stvongly influences the fatigue mechanism by a covrosion process. THE fatigue life of certain metals is known to increase when the atmospheric pressure is reduced. Gough and Sopwith1-2 postulated that this is due to a joint chemical and mechanical process operating in air at the surface of the metal with oxygen and water vapor playing significant roles. Wadsworth and Hutchings3 observed that aluminum is mainly affected by the presence of water vapor. Very little information is available on the fatigue properties of structural aluminum alloys in a vacuum environment. This report describes work performed on 2017-T4 aluminum alloy in an ultrahigh vacuum (2 x 10-loTorr) and in air. Some preliminary data are also presented on the fatigue life of the alloy in a dry-nitrogen environment. 1) EXPERIMENT 1.1) Test Material. The material tested was commerciaT 2017-T4 aluminum alloy which, in addition to aluminum, has an approximate composition of 4 pct Cu, 1 pct Fe, 0.8 pct Si, 0.5 pct Mg, 0.5 pct Mn, plus smaller amounts of other elements.* Some typical naturally age to a substantially stable condition. Specimens were then machined from these rods and ground to a No. 8 microfinish. In order to minimize variation in material characteristics, specimens were made from rods procured from the same lot. 1.2) Apparatus. The apparatus and test specimen used in the fatigue tests are shown in Fig. 1. The device utilized a single-cantilever beam with rotating-bending loading. Bending stress was applied to the fatigue test specimen by placing a spacer beneath the bearing support, thereby providing a constant deflec-

Jan 1, 1968

By A. H. Daane, B. J. Beaudry

The yttl-irtm-nickel system has been investigated by metallo-graphic, thermal ard X-ray methods. There are nine intermetal-lic compounds present: Y3Ni, Y3Ni,, YNi,, YNi,, Y,Ni,, YNi,, and Y,Nil, which rodergo peritectic decomposition and YNi and YNi, which melt congruently. There are eutectics at 34.8, 57.5 and 93.3 at pct Ni which melt at 805°, 950 and 1285 C, respectively. Crystallographic data are given for YNi, YNi,, YNi,, YNi5and Y,Ni,. The terminal solid solubility is low. In recent work by Fisher and Fullhart' in which yttrium crucibles to be used for containers of uranium-chromium eutectic were clad with a high nickel steel, a low melting phase formed where the yttrium was in contact with the steel. To investigate the cause of this phenomenon, Daane, et al. made a survey study of yttrium systems with chromium, manganese, iron, and nickel and found an 18 wt pct Ni (weight percent) alloy to melt at approximately 950°C. voge13 in a study of the systems of cerium, lanthanum, and praseodymium with nickel found six compounds of the same formula in each system, i.e., R3Ni, RNi, RNiz, RNi3, RNi4, and RNi5. Since there is a great similarity between yttrium and the rare earths, compound formation was likely to occur also in the yttrium-nickel system. voge13 observed that the ability of transition metals to form compounds with the rare earths diminishes in the order nickel, cobalt, and iron while no compounds are formed with manganese, chromium, and titanium. Available data on yttrium systems with these elements indicate similar behavior, except that a slightly greater tendency toward compound formation is apparent. Simple eutectics with limited solid solubility have been found in the yttrium-titanium4 and yttrium-chromium5 systems, but at least one compound is present in the yttrium-manganese system.' In the case of yttrium-iron, at least three compounds are present,5 while only two are present in the cerium-iron,' and no compounds are present in the lanthanum-iron5 system. On the basis of both the trend in the alloying behavior of yttrium and rare-earth metals with the first transition series metals and the large number of compounds in the cerium-nickel system, one might expect six or more compounds to form in the nickel-yttrium system. A consideration of Hume-Rothery's rules of alloying based on size factor, electronegati-vity, and valence predicted low terminal solid solubility and possible compound formation. The present study was undertaken to confirm these predictions of

Jan 1, 1961

By B. Amadei

INTRODUCTION Laboratory studies on the deformability and strength of intact rocks generally involve the uniaxial compression test, the standard triaxial compression test and direct or indirect tension tests. If [al ,a2 ,a3] are principal stresses [(al>a2>a3)] with compression taken as positive and tension taken as negative, the applied stress field for each one of these tests can be represented as shown in Fig. 1. However, for most in-situ conditions, such as those that exist at any point around an underground excavation, the stress field is truly three-dimensional or multiaxial [(al+ a2+a3)] and none of the tests shown in Fig. 1 can be used to predict the mechanical behavior of the rock. There are special cases for which one of the three principal stresses vanishes. Biaxial loading of rocks in-situ takes place, for instance, when rocks deform and fail in plane stress conditions. This can occur in a free unloaded surface of a rock structure such as in the wall of an underground excavation or a rock slope. Parallel to the free surface, the stress field components can be both compressive [(al>a2>0)], both tensile [(O>a2>a3)], or mixed, one component being compressive and the other one tensile [(U~>O>U~)]. The purpose of this paper is to present the results of 25 true biaxial tests that have been conducted on cubical specimens of Indiana Limestone using the multiaxial cell available at the University of Colorado at Boulder. The tests include uniaxial compression and tension, biaxial compression and combined biaxil compression- tension. Flexible fluid cushions and brush bearing platens were used for compressive and tensile loading respectively in order to minimize loading end effects on the test specimens. The paper begins with a review of previous investigations on the multiaxial behavior of rock. Then, test results are presented in terms of

Jan 1, 1984

By W. L. DeMoulin

A rather detailed description of the entire plant and leaching process was given in a paper recently presented to the Institute,I so this paper will cover briefly only the crushing practice of the New Cornelia Copper Co. for the year 1918. The ore, which is mined by steam shovels and loaded in side-dump cars, passes through two crushing plants. These crushing plants were constructed to crush the ore required by a leaching plant of 5000 tons daily capacity, during a crushing period of 16 hours. The primary plant reduces to less than 3 in. (76 mm.) and the secondary plant, to 1/4 in. (6.35 mm.), which is sufficiently fine for satisfactory percolation of solution through the ore in the leaching tanks, and to give-good extraction. The ore is then conveyed to the leaching tanks by a system of 28-in. (71-cm.) belt conveyors. On the way to the leaching tanks, it passes through an automatic sampling plant, where a 1-per cent. sample is taken. From the primary crushing plant, the ore is conveyed by two 36-in. (91-cm.) belt conveyors to a 10,000-ton steel storage bin, with a reinforced-concrete flat bottom. The ore discharges from the bottom of this' bin onto four 20-in. belt conveyors, which deliver it to the four units of crushers in the secondary crushing plant. There is no storage bin between the mine and the primary crushing plant. The ore breaks very coarse, is very hard, and contains a great many boulders, some as large as 4 1/2 by 4 1/2 by 10 ft. (1.3 by 1.3 by 3 m.). Jams form in the bowl of the coarse crusher in the primary crushing plant, as a consequence, and are freed by means of an immense steel hook operated from a 40-ton electric traveling crane. Primary Crushing Plant The primary plant consists of one No. 24 Gates, style K, gyratory crusher, followed by four Gates No. 8, style K, gyratory crushers. All

Jan 1, 1920

By G. N. Maniar

G. W. Healy (union Carbide Metals Co.)-The author's paper is a useful contribution to the store of maps of chemical activities of oxides in multi-component slag systems. It is also a good example of the utility of the Gibbs-Schuhmann technique for calculating activities in a system where that of one of the components has been measured. This paper Koh and Caugherty. This plot is reproduced by alor in X-ray Metallography. Because of this nonlinearity, preparation cf suitable standards and/or correction for absorption and enhancement are essential in microanalysis. However, our objection is not the conclusion that Dr. Aaronson has arrived at nor the technique he has used; but only to the foot-note credited to V. Macres. The level of chromium that he was concerned with (less than 3 pet) is so low that the deviation of uncorrected Cr-curve will be negligible. Besides Dr. Aaronson has used chromium intensity from martensite and set it equal the bulk chromium content of the alloy. Using this chromium-intensity as a reference, he has calculated the amount of chromium in the ferrite. This amounts to the same as using an internal standard. Since the chromium content in austenite and ferrite are almost the same, enhancement due to iron in both will be the same and therefore does not need to be corrected. together with the author's recently published one1 on the CaO-FeO-Fezo3 system will be most helpful to others learning to apply Schuhmann's method, which merits a far wider application than it has received to date and should greatly aid our understanding of equilibria between metal and oxide phases. As shown by okcen" its use may even be extended to sections of systems with any number of oxides. I have some questions as to the selection of equilibrium constants made by Dr. Turkdogan. He has chosen one for the formation of Fe2O3 from FeO and oxygen which gives Fea3 activities 50 pct higher

Jan 1, 1963

By I. N. Knapp

Introduction.-The special object of these notes is to describe the mixing, testing, and use of mud-ladened water for rotary drilling in such a way as to make them helpful to the driller, the operator, or the engineer in solving his own special drilling problems. The structures, apparatus and tools used are indicated in a general way. No attempt is made to describe the art of rotary drilling; only such description as are necessary to make plain the use of mud are given. The information is the result of actual experience in drilling in Coastal Plain formations. The materials encountered in the wells drilled were unconsolidated sands, gravels, and clays, in which thin layers of sandstones, shell conglomerates, and shales began to appear at about 1,200 ft. in depth, although one well was drilled to 3,018 ft. without encountering any cemented or indurated materials. Unusual Conditions.-The general surface of the ground where the drilling was done being hardly a foot above mean tide, and the daily tidal variation being about 15 in., it was found necessary to plank over the sod surface with 3-in. plank to work from. A 30 by 30 ft. planked area was sufficient to carry the derrick with equipment and 2,500 ft. of 4-in. drill pipe stacked in it. The derrick was set up 3 ft. on cribbed blocking arranged to spread the load over the planking. The engine, boilers, and pipe yard were also carried on 3-in. planking. Drilling Outfit.-This consisted of a derrick, 20 by 20 ft. and 84 ft. high, two 35 h.p., "oil country" boilers, one double 8 ¼ by 10 in. reversible engine, two 10 by 6 by 12 in. duplex mud pumps, one 15-in. rotary, "hoisting works" with chain drive, hoisting block with line, crown block with pulleys, rotary' jetting swivels, hose, complement of tools, pipes and connections, and. a mud mixer, with engine.

Jan 12, 1914

By David Segura

THE Huitzuco mercury deposits have been described by C. W. Vaupell,1 therefore the general information such as location, history, production, etc. will not be repeated here. The present owners acquired the property when the deep levels of the Cruz mine were flooded, and it was believed that a relatively large tonnage of low-grade ore and fills would be encountered in the flooded section, because of the early mining methods used in the Cruz mine. The mine was partly unwatered and about 187,000 tons of fills was pit-sampled in the San Cayetano stope. These fills average 2.4 kg. Hg per ton. During the period of maximum production at Huitzuco, the ores were sorted in the mine and cobbed into 3-in. pieces, which were treated in Scott furnaces. Large pieces of raw ore are found in the sinter, and it is indicated that both recovery and costs were not very satisfactory. Recent practice has been to treat the ores in closed retorts made of 10-in. pipes. Because of the presence of combined antimony in the mineral livingstonite (HgS.2Sb2S3) and considerable native sulphur, little or no metallic mercury is recovered in the condensers and a second retorting of the condenser muds is necessary. This makes the treatment of the ores expensive and tends to low recoveries of mercury. The principal costs of retorting are, in their relative order: (1) fuel, (2) low recovery of mercury, (3) replacement of retort pipes, (4) labor. METHODS TESTED Three series of experiments have been made, with the object of reducing the costs of recovering mercury and antimony from the ores, by: (1) wet metallurgical methods, (2) bulk roasting in large mechanical furnaces, (3) concentration to reduce the bulk to be followed by roasting in some mechanical furnace. The wet metallurgical methods did not appear feasible because of the high cost of the alkaline solvents used, and investigations of these were not carried beyond the preliminary stage.

Jan 1, 1938

By M. J. Hordon, M. A. Wright

The well-defined increase in fatigue life observed o many metals cyclicly strained at vacuum levels below 10-1 to 10-3 torr has been attributed to the critical retardation of oxygen or water vapor chemisorption at the crack tip during crack propagation.1-3 In the absence of strongly adsorbed surface films, crack re-welding during cyclic compression or dislocation escape from the plastic zone around the crack tip has been proposed to account for the observed decrease in the rate of crack growth. The increase in the critical pressure required for the transition in crack growth rate with temperature experimentally determined for aluminum was found to be generally in accord with the adsorption rate model.4 However, although the adsorption mechanism would also predict an increase in transition pressure and fatigue life with increase in cyclic loading rate, and such effects were noted by Snowden5 for lead and Hordon3 for aluminum, the opposite results were reported by Kramer et al.B in studies on aluminum. The present note describes some recent measurements of the fatigue properties of 1100-H14 aluminum at low pressures to determine the specific effect of cyclic strain frequency in the transition pressure range. Flat cantilever-type specimens of 1100-H14 aluminum shaped to produce a uniform strain gradient along the gage length were tested in reverse plane bending at constant deflection amplitudes in two independent multi-specimen vacuum fatigue systems. One series of tests using 2-in. gage length specimens was conducted in an ion pumped apparatus with 107 torr and 50 cps capacity, denoted as Unit I, utilizing fixed mechanical cams to impose the strain amplitude. An independent test series using shorter 1-in. gage length specimens was conducted in a cryopumped apparatus designed for extremely low pressures below 10-10 torr, denoted as Unit II, using an electromechanical vibrator at non-resonant frequencies up to 150 cps to provide the deflection. Both vacuum fatigue units and associated test procedures have been described previously.3'7

Jan 1, 1969

By Arthur Knapp

Oil-well depletion curves, to be of value, should show when a well or lease may no longer be operated at a profit. The difference, at any time, between the total expenditures and the total income of a lease or well may be called the lease status. Plotting this lease status against time will give a curve subject to more accurate and different interpretations than the barrels-time curves. According to the hypothetical barrels-time curves shown in Fig. 1, well A, at the end of 16 mo., is producing twice as much oil as well B and will continue to produce for another year whereas well B will cease producing in about 6 months. Data fob Lease Status-time or Dollars-timb Curve Time Lease Months Status Lease purchased for $3000.............................. 0 — $ 3,000 No expenses chargeable to lease for 3 mo................. 2 — 3,000 Well A is started; cost of drilling for month is $16,000..... 3 — 19,000 Well is completed at additional cost of $10,000............ 4 - 29,000 Well A is brought in and flows 10,000 bbl. first month (we Fig. 1). Necessary to invest in tanks, boilers, pipe lines, etc.; difference between expenditures and receipts gives profit for month of $5,000............................ 5 — 24,000 Investment is small, cost of operating well A is small, so profits are $15,000................................... 6 — 9,000 Well ceases to flow so there is additional investment for pumping equipment and additional operating expense; net earnings from 6,000 bbl. of oil produced is $4,000. 7 ... Lease operation nor becomes normal and curve becomes smooth........................................... 8 — 500 9 2,000 10 4,500 11 6,000 12 7,700 13 8,700 14 9,000 15 9,500 16 10,000 A hypothetical lease status-time, or dollars-time, curve of this lease is shown in Fig. 2. At zero time, the lease is purchased for $3000, which is plotted below the zero dollar line, All subsequent entries are plotted

Jan 1, 1921

By R. H. Hiltz, N. J. Grant

Solid-solution titanium-cerium alloys, cold-rolled to 0.010 in. thickness, and annealed, were internally oxidized to produce a fine dispersion of CeO2 in the titanium matrix. The oxidized alloys were cut into sheet stress-rupture specimens and tested for rupture life at 426°C, 538°C, and 648°C. There was noted an improvement in strength over that of pure titanium, the internally-oxidized alloys showing curves with a much flatter slope on the log stress—log rupture life plot, characteristic of the stable metal-metal oxide class of alloy. DURING the past 3 to 4-year period, considerable interest has been aroused by the potential offered by alloys based on the ultra fine dispersion of a hard insoluble phase in pure metals or solid-solution alloys for use at high temperatures. The impetus to the development and study of such alloys was provided by Irmann.1,2 through the success of the SAP alloy (pure aluminum containing about 12-14 volume pct of A12O3). Subsequent studies have thrown light on the true potential of this class of alloys in the remarkable stability of the structure after long-time exposure at high stresses and high temperatures.a-5 While success has been demonstrated in the special case of the A1-Al2O3 alloys, and more recently

Jan 1, 1959

By L. C. Weiner

For zinc single crystals, xo = 3o, a surface coating raises both the cleavage and yield strengths over a large temperature range. The "brittle temperature," associated with slip after completion of twinning, does not coincide with the point of intersection of the flow and cleavage curves, which is associated with twinning. A surface film has no effect on the brittle temperature, while it lowers the intersection temperature some 20°. For crystals, yn = 83o, a coating decreases the cleavage strength, making it temperature independent, as well as increases the brittle temperature or its equivalent, the intersection temperature, 20°. These observations are described on the basis of a dislocation-pile-up-at-a-barrier model for brittle fracture; in crystals x,, = 3o the number and distribution of twins play a vital role. IN a recent investigation on the effects of solid environments on the brittle fracture of zinc single crystals,' it was demonstrated that the presence of a surface film changes the cleavage strength of these crystals, either increasing or decreasing it, depending on the crystal orientation. An increase in cleavage strength of some 43 per cent was found for coated crystals oriented x, — 3o K = 28",* while a decrease of 48 per cent was observed with crystals X" = y» — 83". Moreover, these effects were found

Jan 1, 1959

By Peter J. Conroy, Julianne H. Gyarmaty

INTRODUCTION The current study is part of the U.S. Department of Energy's (DOE) on-going subsidence research program. The long-term objective of the DOE program is to develop analytical methods of subsidence prediction applicable over a broad range of geologic and mining conditions encountered in the United States. The DOE currently has several contracts in progress to develop a sound data base that can be used in the development of predictive models. Dames & Moore is currently under contract to DOE to collect and analyze detailed subsidence and hydrologic data from a coal mine employing longwall mining methods in the Eastern Coal Province. Work under Contract No. DE-AC22-80PC 30335 began in October of 1980 and will continue through September of 1984. The contract includes monitoring of two adjacent longwall panels. This paper summarizes the surface monitoring work that was performed through February of 1982. Mining of the first of the two panels (3 off 3 north) was completed on February 3, 1982. Results of the surface monitoring through completion of this panel are presented and discussed. SITE DESCRIPTION The mine being studied is located in eastern Ohio. The site is west of the Ohio River, approximately 56 km (35 miles) south of Wheeling, West Virginia. The topography of the unglaciated region

Jan 1, 1982

By R. C. Davis, R. F. Berry, G. W. White, B. T. O’Connell, L. A. Stacha

P,, and v, may now be solved for by trial and error between Eqs. 2 and 3, by assuming time approaching zero and equating PI, to P12. Observe that the pressure under the slug, P12 of Eq. 3, does not remain equal to the P1, at the valve in Eq. 2 as the slug proceeds up the hole. To plot the profile of pressure vs depth, it is necessary to express P12 in terms of P11. To do so, the extent to which the original submergence length S changes with respect to time must be analyzed. At the end of time t after injection, the actual value of L in Fig. 3 is The fall-back v,(t) is now distributed in the gas and exerts pressure on the bottom. This, in addition to the weight of the gas, amounts to the difference in pressures from point to point. With the average pressure profile calculable, a true numerical value for the average pressure in the tubing may be obtained. The value of v, must be obtained experimentally, and since v,, S and D are known, the basic Eq. 1 may be solved for the amount produced. Knowing P, and the actual volume of tubing occupied by gas (vat), it is possible to calculate the volume of gas at standard conditions which is present in the

By Theodore Nagel

Fuel-oil, natural gas and coke oven gas, producing the higher temperatures of open-hearth current practice, have been gradually displacing producer gas the lowest cost fuel for open hearth operations. The lower temperatures of combustion products from producer gas is caused by nitrogen dilution. Practical Application of Combustion Thermochemistry One pound of carbon burned to CO produces 3,960 B.T.U. and one pound of carbon burned to C02 produces 14,140 B.T.U. The second unit of oxygen uniting-with gasified car-bon (-CO) produces (14,140 - 3,960) 10,180 B.T.U. which is;(10,180 - 3,960) 6,220 B.T.U. more heat than produced by the first, unit of oxygen forming CO by uniting with solid carbon. A review of the relative combustion heating values of commercial gaseous fuels reveals CO requires a minimum of air for combustion, and because of minimum nitrogen dilution and the high thermal release from CO higher temperature combustion products are produced from CO than from natural gas or from coke-oven gas under similar combustion conditions. Inert nitrogen diluent lowers the calorific value of fuel gas and its diluting effect is cumulative in lowering the temperature of the products of total, combustion. It is not only logical but, practical in partial combustion, converting bituminous coal to gas, to generate the gas, with reduced nitrogen dilution.

Jan 1, 1936