Search Documents

By Milo Krejci

(Butte Meeting, August, 1913.) THE plant and quarries of the Inland Portland Cement Co. are located at Metaline Falls, Wash., about 128 miles north of Spokane, on the Pend Oreille river, and within 10 miles of the Canadian border. The plant is one of a chain of cement plants controlled by the Lehigh Portland Cement Co., of Allentown, Pa. Work on this plant was commenced in June, 1910, and was completed in April, 1911, but on account of some delays in 'the construction of the power plant, the works were not put into operation until August, 1911. Since then it has been in continuous operation and has furnished the Inland Empire with a high grade of cement. Fig. I is a view and Fig. 2 is a plan of the works. Water Power Development.-The source of the water supply for the hydro-electric plant of the Inland Portland Cement Co. is Sullivan lake, a body of water approximately 5.5 miles long and 0.5 mile wide, situated in the Kaniksu Forest Reserve. A wooden crib dam was installed so as to raise the elevation of the lake 25 ft., and the additional storage capacity was taken up by the diversion of Sullivan creek into the lake by means of a wooden flume, 0.25 mile long, 6 by S ft. in cross-section, and a ditch 1,200 ft. long. The water from the lake follows the natural water course to an intermediate storage reservoir, which was created by the construction of an earthen dam. This pond wits used in connection with the saw mill which was installed at this point. Besides the earth dam, there was also built a crib, at the point shown in the sketch map, Fig. 3. This crib dam is 35 ft. high. From this point the excess water follows the natural course of Sullivan creek to the Pend Oreille river.

Jan 7, 1913

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, 1871 1 3 2 Bethlehem, Pa August, 1871 1 10 3 Troy, N Y November, 1871 1 13 4 Philadelphia, Pa February, 1872 1 17 5 New York, N Y May, 1872 1 20 6 Pittsburg, Pa October, 1872 1 25 7 Boston, Mass February, 1873 1 28 8 Philadelphia, Pa May, 1873 2 3 9 Easton, Pa October, 1873 2 7 10 New York, N Y February, 1874 211 11 St Louis, Mo May, 1874 3 3 12 Hazleton, Pa October, 1874 3 8 13 New Haven, Conn February, 1875 3 15 14 Dover, N J May, 1875 4 3 15 Cleveland, 0 October, 1875 4 9 16 Washington, D C February, 1876 4 18 17 Philadelphia, Pat June, 1876, 5 3 18 Philadelphia, Pa October, 1876 5 9 19 New York, N Y February, 1877 5 27 20 Wilkes-Barre, Pa May, 1877 6 3 21 Amenia, N Y October, 1877 6 10

Jan 1, 1917

By P. W. Neurath

IN recent years the domain theory of ferromag-netism has been put on a sound experimental and theoretical basis. But its application to one of the most widely used high quality magnetic materials, the cold-rolled grain-oriented 3 pct Si-Fe used in transformer cores, has been rather difficult because of the complexity of the domain structure of the poly crystalline sheet material. This paper presents some experimental data for this material, showing the relation between plastic and elastic stresses, 60-cycle watt losses, and the domain structure as observed visually. Only a very tentative qualitative explanation of the effects will be attempted. Some initial results were reported earlier.'

Jan 1, 1957

By F. M. Sandoval, R. E. Ries, J. F. Power

Returning the original soil material to the surface of smoothed mine spoils is a practical means of restoring agricultural productivity. Research has established that high-sodium spoils in North Dakota: (1) must be covered with about 70 cm of soil material to achieve maximum production; (2) top-soil must be segregated and spread separately from subsoil; (3) potential production depends on the quality of the soil material returned; and (4) erosion and upward salt movement must be controlled for sustained production. Erosion is best controlled by reducing final grades as much as possible during the smoothing process followed by prompt establishment of vegetation.

Jan 1, 1980

By M. C. Fuerstenau, J. D. Miller

The response of calcite to flotation with saturated fatty acids and alkyl sulfonates of various chain lengths is presented. The amount of collector re-quired for flotation is shown to decrease systemati-cally with increasing carbon content from 8 to 12-carbon atoms per molecule. This systematic flotation response is correlated with the solubilities of the calcium-collector salts, which were established with a nephelometer. The 14-carbon collectors deviate from this systematic behavior, and no flotation is possible with the 16-carbon homologs. As determined by infrared analysis, the mechanism of collector adsorption involves a specific chemical reaction be-tween the collector and the surface. A reaction of the form CaCO3(s)+ 2 RCOO"=*=Ca(RCOO)2(s) + C03= is suggested. The pH of the system is also shown to be a most important parameter as it controls the carbonate, calcium, and collector ion concentrations in solution and thus controls flotation response. The importance of hydrocarbon chain length of collectors was recognized early, and various studies have been made on this aspect of flotation. Wilkinson, ' for example, noted that as the chain length of alkyl xanthates is increased, the amount of collector required for flotation of sphalerite is decreased. The same effect has been shown in the flotation of galena.2 Similar results were obtained when malachite3 and calcite4 were floated with various fatty acids. DeBruyn5 has shown that a similar phenomenon occurs when quartz is floated with amines at constant pH. Recently, Fuerstenau, Healy, and Somasundaran6 correlated this phenomenon with the van der Waals cohesive free energy of association of the hydrocarbon chains. It seems unlikely, however, that chain association could be involved in the sulfide and carbonate systems with the collector additions employed, especially with the short-chain xanthates. Rather, it would seem that the decrease in collector concentration with increase in chain length noted for flotation is related to the solubility of the metal-collector salt. The purpose of this investigation is to verify this premise and also quantify this phenomenon if possible. Calcite was selected for study with both alkyl sulfonates and saturated fatty acids as collectors. EXPERIMENTAL MATERIALS AND METHODS The collectors used in this investigation ranged from 8 through 14 carbon atoms per molecule. The fatty acids had a reported purity of greater than 99%. The sodium alkyl sulfonates were provided by the Marathon Oil Cot, Littleton, Colorado, and had the

Jan 1, 1968

By George K. Burgess, Robert A. Hadfield

1. Introduction.—The methods of production of sound steel ingots have been described in several papers read recently before this Institute. It was thought by Director Stratton, of the U. S. Bureau of Standards, and ourselves to be of sufficient interest and importance, as a further contribution to this subject, to compare the properties of rails rolled in one mill according to American practice, from several types of ingot of substantially the same chemical composition but cast by several processes; and to compare in considerable detail the properties of an ingot manufactured by the Hadfield special-feeding process and one of the usual type for rolling into rails. We are greatly indebted to F. W. Wood, President of the Maryland Steel CO., who made this investigation possible by kindly placing his rail mill at our disposal; and he and his associates at Sparrows Point did everything possible to make the experiment a success, including the execution of several of the tests and analyses. 2. Classification and Manufacture of Ingots.—Of the ingots used in this investigation, eight were made in Sheffield and furnished by Sir Robert Hadfield, and one was made and furnished by an American steel company,l as a comparison ingot, and was supposed to represent the usual type of ingot from which rails are made. The characteristics of the ingots are given in Table I. Ingots 1, 2, 3, and 4 were cast large end up and fed by the Hadfield method in the usual manner with charcoal and blast continued until the molten steel has set on the top of the head, say varying from 20 to 40 min. To ingots 1, 2, and 4 was added 0.1 per cent. aluminum, and to the nickel-chrome ingot, No. 3, 0.125 per cent. For sake of comparison, there were also included two ingots, Nos. 8 and 9, cast with the small end up and fed by

Jan 1, 1915

By B. M. Larsen, L. S. Darken

SOME years ago we collated all laboratory data then available to us on the distribution at equilibrium of manganese and of sulphur between metal and simple slags, and used the results in setting up an equation, which proved to be in accord with determinations of the distribution ratio of manganese and of sulphur between liquid steel and open-hearth slag, over a wide range of operating conditions. We now present an outline of our calculations and inferences on these two closely related questions, which are of especial importance because of the advisability of conserving manganese wherever possible. In general, our results show that in the open-hearth furnace equilibrium between metal and slag, with respect to both manganese and sulphur, is substantially attained during the finishing period of the heat, or in about a half hour to an hour after any additions were made. This implies that the end result will be identical whether manganese is added as alloy or metal to the liquid steel or as oxide to the slag. The proportion of total manganese retained by the steel is favored: (I) by use of the minimum amount of lime, consistent with other operating limitations, required to give a lime-silica ratio of about 2.4, which usually corresponds to a minimum practical slag volume; (2) by a high concentration in the slag of MnO relative to FeO; (3) by high operating temperature. Absorption of sulphur by the slag from the liquid metal is favored: (I) by large slag volume; (2 by a high concentration of active (or "free") lime and of manganese oxide dis) solved in the slag; (3) by low concentration of silica, iron oxide, and phosphate dissolved in the slag. DISTRIBUTION OF MANGANESE BETWEEN SLAG AND METAL AT EQUILIBRIUM On the basis that the distribution of manganese between liquid steel and slag is controlled by the reaction [FeO + Mn = MnO + Fe [A]slag metal slag metal] the distribution at equilibrium, at a given temperature, is expressed by the equilibrium constant for this reaction, which is defined as [K" aMoO aFeI1 dFec) aMn] where a is the activity of the molecular species denoted by the subscript. The activity of each of the several components, although it is not known precisely, is approximately equal to the concentration of each component expressed as its mol fraction; that is, as the ratio of the number of mols of the given component to the total number of mols of all the molecular species present in the metal or slag, as the case may be. Moreover, since the activity, or concentration, of iron in the liquid metal is in fact substantially constant, the term [afe] may be combined with K" to give a new constant K'. Making these changes,

Jan 1, 1942

By D. J. Jr. McAdam

RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station have been presented by the author in four papers. 1,2,3,4 In those papers references were given to the work of Haigh in 1917.5 The investigation at Annapolis included a variety of ferrous and non-ferrous alloys. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at stresses far below the ordinary endurance limit. The experiments also showed that, for most metals, severe stressless corrosion prior to fatigue is much less damaging than even slight corrosion simultaneous with fatigue. The term "corrosion-fatigue" was restricted to mean the simultaneous action of corrosion and fatigue. The combined effect of corrosion followed by fatigue was called "prior-corrosion fatigue." A stress-cycle graph representing corrosion-fatigue is a curve approaching a horizontal asymptote, the ordinate of which may be called a "corrosion-fatigue limit." To avoid confusion in later discussion, the term "endurance limit" will be restricted to mean the fatigue limit obtained by tests in air with specimens as free as possible from stress concentration and from corrosion. The endurance limit as thus obtained presumably represents an inherent property of the metal.

Jan 1, 1929

By E. S. Greiner

STUDY of the plasticity of germanium or other semiconductor crystals affords unusual opportunities to extend our knowledge of deformation mechanisms. Crystals are available having extraordinary perfection and very high purity. They deform by slip on the systems {111} <110>,1-3 as do crystals of the simple face-centered-cubic structure. Dislocations generated in them during slip are easily revealed in the form of etch pits on either (111) or (100) surfaces.4,5 This fact alone makes possible more detailed studies of mechanisms than is usually the case with metals but, even further, the effect of deformation on their electrical conductivity is very large compared with metals. This comes about not only because the mobility of the charge carriers is reduced, as in deformed metals, but also because the number of these carriers is greatly altered. This latter effect seems closely related to the formation of both line and point imperfections during deformation and thus provides a needed tool for the study of the kinds and distributions of these imperfections. Other investigators have deformed germanium at elevated temperatures by bending,1, 6-8 compres-sion,6, 0,10 tension,2,3,6,11,12 torsion,23 and indentation." Wang and Alexander" have also reported successful indentation at room temperature. Dislocation etch pits consequent to deformation have been observed and studied.7,8,10,18,14,20 The experiments to be de- scribed here include principally the compression and the subsequent annealing of germanium with concomitant studies of etch pits, microstructures, and electrical properties. Both single crystals and heavily twinned specimens were used. Some indentation studies are included. Experimental Methods Plastic compression was effected in the apparatus shown schematically in Fig. 1. It consists of two tantalum platens contained in a helium atmosphere and so arranged that pressure can be applied by a hydraulic press. The specimen between the platens is heated by the surrounding furnace. The specimen is usually a small crystal cube about 0.30 in. on an edge. A control specimen is always inserted so, that it is subject to the same thermal cycle as the one being deformed. This serves to detect any impurity contamination that might accompany the thermal treatment. For high temperature work, where such impurity contamination often occurs, the specimens were first plated with gold whenever subsequent electrical properties were to be determined. This method" is effective in preventing significant contamination of germanium up to temperatures at least as high as 750°C, as evidenced by the constancy of the electrical conductivities of control specimens subjected to the same heat treatments. The total range of temperature used for deformation was from 375°C, the lowest at which significant flow was observed, up to 900°C. Microscopic examination was made after mechanical and chemical polishing and etching. Dislocation pits were revealed with CP-4 etchant by the tech-

Jan 1, 1958

By J. Campbell

The hydrostatic tensions in pure metals and long freezing range alloys are evaluated theoretically considering the viscous flow of residual liquid and the general plastic collapse of the casting. The former mechanism operates until the radii of the remaining liquid channels are of the order of 10-3 cm radius, after which the second process limits the attainable negative pressures which range from —1500 to -4200 atm for nickel, aluminum, copper, and iron. In previous reports1&apos;2 the maximum possible hydrostatic tensions developed during solidification have been evaluated employing spherical symmetry. This inevitably involves the concept of totally confined liquid regions, the reality of which has recently been brought into serious doubt3 following observations of the freezing of various transparent materials. Regions of interdendritic liquid which are apparently about to be isolated by the growth of dendrite arms are observed not to be cut off because the advance of the dendrite tips is arrested until the region has completely solidified. Although this may be the result of the very low melting point liquid available at this late stage in freezing, or the result of a higher rate of heat transfer to the dendrite tips because of the acceleration in liquid flow rate near the completion of solidification, this point need not concern us. In this paper an attempt is made to approximate more closely to real conditions; thus the assumption of confined liquid regions is abandoned and cylindrical symmetry adopted. It has also been necessary, therefore, to consider the viscous flow of residual liquid through the remaining channels in the pasty zone. Furthermore, the rather special conditions of spherically symmetric solidification led to extremely high solidification rates and hence unusually high tensile stresses as solidification neared completion; the cylindrical Symmetry appears to yield solidification rates and stresses which are more typical of real castings. The rate of solidification is first considered since this critically affects both the flow of the liquid and the creep of the solid.

Jan 1, 1969

By J. C. Jaeger, G. A. Wiebols, N. G. W. Cook

It is usual practice in engineering to design a stable structure by ensuring that the stresses in the elements of the structure are always less than their strength, which may be defined as the yield stress, the ultimate stress, or the fatigue stress, according to the type of the load. Such restrictive design is not practical in the design of underground excavations since the rock surrounding such structures is usually failed, but only occasionally does this give rise to instability of the structure. Thus, while the usual criterion for the design of a stable structure is certainly sufficient, it is not necessary for underground excavations. A proper understanding of the conditions necessary for stability is vital to the useful application of rock mechanics knowledge to the design of underground structures. Most tests on the properties and strength of brittle rocks are disrupted at or near maximum load by the rapid release into the specimen of energy stored in the resilience of the testing machine. This is in contrast with a phenomenon, which may be observed frequently, where the rock immediately surrounding an excavation is both failed and subject to stress. By postulating a complete stress-strain curve for rock, it can be shown that failure is unstable or stable, depending upon whether the stress-strain curve of the rock lies inside or outside the stress-strain characteristics of the applied stress. Stability is, therefore, a function of the stiffness of the system applying the stress relative to that of the failing rock. Many workers have established that the strength of rock specimens under a lateral hydrostatic confining stress varies linearly with confining stress, in a way which may be expressed by the equation CT=Co+K[o]3

Jan 1, 1972

By D. Moskowitz

IN the course of a general investigation of boride systems, sponsored by the Office of Naval Research, various vanadium boride powders of relatively good purity were prepared which could be used for a determination of the phases present. The X-ray pattern of one of these lots showed, in addition to the known VB1 and VB22 phases, an additional phase, almost certainly of composition V3B4, isomorphous with Cr3B4, Cb3B4, Ta3B4, and Mn3B,. Its pattern fitted in well with the indices worked out by Kiessling for Mr3B4.3 The unit cell for this new compound is orthorhombic, with the dimensions a = 3.030A, b = 13.18A, c = 2.986A7 V=119.2A.&apos; Table I lists the X-ray diffraction data for V.3,.

Jan 1, 1957

By T. L. Fritzlen

EXTRUSION of aluminum alloys in this country is performed mainly by direct extrusion, therefore this paper is confined only to factors affecting the rate of extrusion by this method. Many factors affect the rate of extrusion of aluminum alloys. It is the purpose of this paper to present a discussion on the factors that are subject to technical control. Most of them are closely related, so that a clear-cut distinction between them is rather difficult. However, an attempt will be made to evaluate the effect of each factor separately, as far as possible. The most important factors only will be considered, and these will be discussed in detail under three general headings: (I) characteristics of the equipment, (2) size and structure of the ingot, and (3) temperature of ingot, cylinder, and other parts. It is a well established fact&apos; that the pressure and the speed of extrusion are related and are exponential functions of one another. Therefore, whenever a certain condition tends, for instance, to increase the pressure required for extrusion, it will reduce the extrusion speed if the pressure is maintained constant. For this reason, in this paper the effect of various conditions is expressed either in regard to their effect on the pressure required or the extrusion speed. Another established fact is the relationship between the temperature of the material being extruded and the pressure required to extrude. According to Schishokin,2 this relationship is of the exponential type, and as the temperature is increased the pressure required is decreased. It would seem from the preceding that the greatest rates of extrusion can be obtained by the use of higher temperatures. However, as is well known, other factors intervene to limit the rate of extrusion of aluminum alloys when increasing the temperature. These factors will be discussed in detail later. CHARACTERISTICS OF THE EQUIPMENT The capacity of the press determines the maximum unitary pressure that can be applied for any given cylinder diameter. Pressures used for extrusion of aluminum alloys range from approximately 50,000 lb. per sq. in. to 150,000 lb. per sq. in., dependent upon the alloy and the size of the shape extruded. Higher pressures could be used to advantage, but existing steels limit pressures employed in the production of extrusions. Numerous mechanical characteristics of the extrusion press affect extrusion rate. The most important characteristics of the press itself are: (I) sensitivity of the main pressure valve and accuracy of pressure gauges, (2) accuracy of equipment to heat the cylinder uniformly and to control cylinder temperature, and (3) accuracy of means of measuring the speed of extrusion. The variables subject to control during the extrusion operation are pressure, temperature, and speed, and it is evident that the preceding characteristics

Jan 1, 1945

By R. J. Piros, Brusenback, D. A. Dahlstrom

DEWATERING fine coal has been a serious problem to many operators who desired to wet-wash finer sizes and maintain high recovery. Centrifugal driers have become popular for this purpose for sizes between 3/8 in. and 14 mesh. Below 14 mesh the perforated screen centrifuges lose a large per- cent in the effluent solid bowl types that do retain -14 mesh coal, produce excessive degradation, tend to retain the highest ash fraction in any size fraction, and are subject to abrasion, which results in higher maintenance. In 1949 Truax-Traer Coal Co. planned a cyclone installation at their Ceredo preparation plant to recover coal down to 150 mesh with approximately a 14-mesh top size. Since available centrifugal equipment was not considered satisfactory, an investigation of rotary vacuum filters was begun in cooperation with the Peterson Filters and Engineering Co. to determine the suitability of the Peterson Top Feed Reservoir (TFR) filter. This investigation, which is described below, has resulted in a highly satisfactory installation of two 6x10-in. Peterson TFR filters that have been in operation over a year. After some preliminary laboratory batch vacuum filter tests, a pilot plant double-drum Peterson TFR filter was installed at Ceredo to prove the feasibility of vacuum filtration and determine optimum conditions. The full scale units were then installed on the basis of the pilot plant results. This was followed by an extensive research program on vacuum filtration in the laboratory at Northwestern University to investigate basic design and operating variables and their influence on final moisture con- tent of the filter cake. A method of scale-up from laboratory batch tests to the full-size unit was also proposed and proved. Because of the importance of dewatering fine coal today, it was felt that the results of the three steps should be made available for the use of others facing this problem. The work at Northwestern is given in a theoretical section following the discussion of the pilot plant and full- scale operation. Fig. 1 is a flow diagram of the cyclone and filter installation. The feed is drawn from below the

Jan 1, 1952

By K. L. Komarek

Based on theoretical and experimental evidence a discussion follows of the behavior of phosphorus -bearing iron ores in the R-N Direct Reduction Process and suggestions are made of methods of reducing the amount of phosphorus in the metallic end product. In ferrous metallurgy a direct reduction process is one in which iron ores are reduced to metallic iron with gaseous or solid reductants without the appearance of a liquid phase. A number of attractive features have induced several companies and government agencies to invest in the development of direct reduction processes. A summary of all direct reduction processes up to 1954 has been given by Barrett,&apos; and Wiberg,2 and Willems3 have reviewed the most recent developments in this rapidly expanding field. Many difficulties have been encountered in direct reduction processes and the nature of these difficulties has varied from process to process. One problem common to almost all of them is the removal of phosphorus which is one of the reasons for the rather pessimistic outlook given by some government publications4&apos;5 to direct reduction processes. In this paper an attempt is made to give a theoretical explanation of the variations in phosphorus removal observed in the R-NY Direct Reduction Process. However, many conclusions are general enough to be applicable to other processes. Most iron ores treated by the R-N process yield products lower in phosphorus than the original ore. A qualitative account of the factors has been given by Stewart, Reed, and Herasymenkoe but the erratic removal of phosphorus from some ores and the general importance of this problem make a more careful analysis of the theoretical aspects desirable. In the R-N process mixed ore or balled fines, ex-

Jan 1, 1963

By Ray W. Arms

DRY cleaning, or pneumatic separation, is not, strictly speaking, a recent discovery. Among the archives of the Patent Office may be found many patents dating back as far as 1850 which cover early attempts to separate materials of varying specific gravity or of different shape by means of air. Hundreds of patents covering this art have been issued, which may be roughly classified into four general groups, as follows: 1. Stationary devices with pulsating air currents. The separating surface is usually riffled and air is supplied by bellows or compressors. This group also includes air jigs, which have been used rather extensively. 2. Stationary devices with continuous air currents. These submitted the material to a continuous current of air, either horizontal or vertical. Chaff is blown from wheat by such a device. 3. Reciprocating or vibrating devices with pulsating air. A small group in which the pulsating air is supplied by bellows and some motion provided in the separating surface to move the stratified material to various discharge points. 4. Reciprocating or vibrating devices with continuous air supply. This is by far the most important group and all recent developments have been along this line. All of the above groups involve the stratification of material by air and include none of the dry methods that use other principles, such as coefficient of friction, magnetism, etc. Air Stratification In all of the above groups of air separating devices, the same phenomena are found as exist in water concentrators; that is, free settling will be found in some and hindered settling in others, with a complex action on the reciprocating tables similar to the wet tables. The experimental value of the settling ratios of particles in air has never been determined but, following the formulas given in Richards&apos;

Jan 1, 1924

By W. T. Thom

Interest naturally attaches to fissuring and subsidence of the earth&apos;s surface, whatever the cause may be, and the induced movement and fissuring of the impervious strata overlying an oil sand is of even greater practical importance because of its bearing upon the recoverability of the portion of the oil not already extracted or extractable by ordinary production methods. It is probably true that significant ground movement induced by oil production occurs only in oil fields in relatively young formations, where the oil comes from incoherent or only slightly cemented sands and oil-soaked clays, but inasmuch as a great proportion of our "gusher" wells produce from "running" sands and yield a large part of the total oil output, it seems worth while to make an effort to inspire the collection and recording of data indicating the nature and magnitude of oil-field subsidence, both surface and subsurface. Goose Creek Field The single known instance in which the nature and magnitude of the surface subsidence incident to petroleum withdrawal has been accurately ascertained is that in the Goose Creek oil field of Texas, described by Pratt and Johnson.&apos; There subsidence caused the submergence of a considerable area within the oil field, and, because the title to the naturally submerged lands of Texas rests in the State, it became necessary to determine whether the submergence was due to natural or artificial causes. A detailed study revealed that the sunken area conformed very closely to the limits of the productive oil field and that the cumulative depression over an eight-year period ranged from zero at the margin to 3.25 ft. at the center. This depression was accompanied by the development of local marginal surface fractures along which the subsiding ares

Jan 1, 1927

By Donald Cummings

CERTAIN dusts are dangerous when inhaled, but most hazardous of all dusts are quartz or other forms of pure crystalline silica. The inhalation of dusts containing silica in combination with other elements gives rise to changes in the lung which differ from those produced by pure silica. As a generality, silicates are less dangerous than pure crystalline silica and vary greatly among themselves in harmfulness. Repeated analyses have shown that approximately 70 per cent of the total number of particles involved in any dust-producing operation are below 1 to 2 microns in diameter. (A micron is. approximately 1/25,000 in.) Similar studies of dusts recovered from silicotic lungs post mortem have demonstrated essentially the same size frequency distribu-tion, except that the upper limit of size retained in the air sacs is approxi-mately 10 microns. Experiments carried on by Gardner and the author have further demonstrated that greater changes were produced by a fixed weight of very fine quartz particles (2 to 3 microns and smaller) than by the same weight of slightly larger particles (8 to 10 microns). Any attempt to control a dust hazard should therefore be directed toward the removal from the working atmosphere of particles less than 10 microns in size, and particularly those below 3 microns. All industrial hygienists agree on this matter, but there remains considerable dispute as to the lower limit of particle size capable of causing injury. It has been gen-erally conceded, however, that particles of harmful dusts smaller than ¼ to ½ micron are not essentially concerned in the development of pulmonary fibrosis. This opinion is partly substantiated by the existence of large numbers of these small particles in practically all atmospheres that are, not associated with any known hazard. Such particles are so small that they have very little mass, fail to settle even in quiet air, and probably are not easily retained in the lung. Until further research proves that they are involved in the dangers provoked by the inhalation of certain dusts, engineers will generally agree that it is better to dis-regard them.

Jan 1, 1935

By Joseph Daniels

The Fritz Engineering Laboratory was built under the direction of John Fritz, and presented by him to the University. A view of the building, looking east, is shown in Fig. 1. The building was started in 1909, and completed in 1910, although all of the equipment was not placed until later. Mr. Fritz gave his personal attention to the details of construction and equipment, and it was his custom to drive over every day to the University from his home in Bethlehem and spend some hours watching the work, offering suggestions, making changes, and planning new work. The result is a building and an equipment which embody his practical ideas. The laboratory structure is of the steel mill-building type, of light-colored brick, 91 by 114 ft., of which a section is shown in Fig. 2 and the floor-plan in Fig. 3. The steel frame carries the roof and traveling crane-way. Ample light has been provided by numerous windows in the side and end walls, in the clerestory, and by a skylight 84 ft. long and 9 ft. wide in the north roof. The main aisle of the building is 49 ft. 2 in. between centers of crane-columns, and has a clear height of 40 ft. The remainder of the width is taken up by two side aisles, 18 ft. high. The laboratory consists of four sections: (1) A general testing-section containing the testing-machinery, a small machine shop, and an office; (2) a cement-testing room; (3) a room for making and storing concrete test-specimens; (4) a hydraulic section.

Jan 1, 1912

By H. G. Sell, G. W. King

An investigation was made of the lensile proper-ties of recrystallized high-purity tungsten and a W-1 pel ThO2 dispersed-phase alloy over the temperature region of 800° to 2400°C. The thoria addition resulted in a modest strengthening effect over the entire temperature region. A decrease in ductility of both materials occurred above 0.5 Tm which was caused by void formation. Current theories of IT has long been recognized that a second phase of hard particles has a strengthening effect on a pure metal. At low or intermediate temperatures (<0.5 Tm), the strengthening effect is thought to arise mainly from the interaction of dislocations with dispersed particles. Above 0.5 Tm, dynamic recovery processes greatly alter the deformation mechanisms from those simply involving glide, and grain bound- strengthening by a dispersed second phase do not adequately explain the tensile results. Melallographic examination suggests that the improved strength of tire alloy results from the effect of thoria on the mierostructure. Stress-dependent thermally activated processes were found to occur high temperatures. aries may act as sources of weakness rather than strength because of grain boundary sliding. Grain boundary sliding at high temperatures has been postulated to be the primary factor giving rise to the formation of voids or cavities at grain boundaries1-3 which in turn cause premature failure and poor ductility.4 Voids, once formed, can grow by the condensation of vacancies from the equilibrium concentration&apos; or from the excess vacancies produced by the deformation.4,5 The high-temperature tensile properties of unalloyed tungsten have previously been investigated by Sikora and Ha116 and also by Taylor and Boone.7 The purpose of the present work was to investigate

Jan 1, 1965