Search Documents

By C. M. Nickerson

In times of overproduction such as the operators have been struggling against for the past several years it is the practice of the oil industry to shut in certain wells in order to reduce the flood of oil. The purpose of this paper is to present certain variations in production of oil wells when the offset wells are shut in. The scope of the study has been confined to California fields, and more especially to those of the San Joaquin Valley. The accepted definition of a shut-in well is a well where production has been suspended by closing in the casinghead arid tubing or by cessation of pumping. The immediate effect of such a procedure, of course, is to reduce the oil production from the lease, which is the result desired. However, it appears that certain types of wells vary widely in production of oil, gas and gasoline after adjacent wells have been shut in, which variation has a very material effect on the ultimate recovery of oil from the property. The increase or decrease in the oil production itself may not be of sufficient volume to occasion comment, but wide fluctuations in the gas and gasoline recovery under the changed conditions arc of the utmost importance in the future recovery of oil. The scope of this paper includes: (I) the effect on producing oil wells of shutting in offset wells, the wells being studied in three groups arranged according to their relative stages of depletion; (2) probable source of excess gas and the effect on the ultimate recovery of oil; (3) suggested procedure when wells are shut in; (4) methods that could be employed to prevent undue migration of gas from the shut-in area; and (5) the need for future studies of the situation. Three Classes of Producing Oil Wells For the purposes of this paper producing wells in California have been arranged in three groups according to the age of the well, or to the relative stage of depletion of the producing zones. The first group consists of those wells with a high fluid level, or in other words those wells whose fluid levels are a considerable distance above the top of the perforations. This type of well is in the flush period of its life and ordinarily produces

Jan 1, 1929

By Vernon Taylor

CANADA'S oil production is obtained almost entirely from the Turner Valley gas and oil field, in the Province of Alberta. This field, about 30 miles southwest of the city of Calgary and approximately 115 miles north of the United States border, supplied 92 per cent of production in Canada during 1937. In 1938 considerable development took place in this field and total production for the year amounted to 6,688,716 bbl., an increase of 3,922,146 bbl. over the production in 1937, which increased the percentage of production to approximately 97 per cent of Canada's total. In the British Empire, Canada's production is thus comparable to that of Bahrein Island and Burma, each of which produced approxi-mately 7,800,000 bbl. in 1937, being second to Trinidad's production of 15,500,000 bbl. The total production of the British Empire in that year amounted to 2.07 per cent of the world's total. HISTORY Development of the Turner Valley field commenced in 1913, when a well was started near a gas seepage on the banks of the South Fork of Sheep River in the central part of the Valley. This well found small quantities of a light crude oil in beds of Upper Cretaceous age and pre-cipitated a wild boom in 1913-1914 which ended with the beginning of the Great War in 1914. A small amount of drilling was done in the years from 1914 to 1922 and a few wells found small crude-oil production in the upper sands. In 1922 a few wells were started, including the Royalite Oil Company's No. 4 well (R, Fig. 1), which became the discovery well of naphtha pro-duction from the Paleozoic limestone. In October 1924, this well was completed at a depth of 3740 ft., being approximately 300 ft, in the lime-stone, with an initial flow of 600 bbl. of 72° A.P.I. gravity naphtha and 20,000 M cu. ft. of gas per day. Intense activity was not started until the latter part of 1928, when the Okalta No. 1 well (Q, Fig. 1) was drilled, with an initial production of 500 bbl. of naphtha per day. This well was only 1 ¼ miles from Royalite No. 4, but it was approximately 1300 ft.

Jan 1, 1939

By Robert E. Green, Kenneth Reifsnider

A microscopic X-ray diffraction technique was employed for the simultaneous study of the behavior of several families of lattice planes, whose local orientatiotz changes are manufestations of internal distortions resulting from specimen deformation. Photographs taken using aluminum were single crystals 1/64 in. In diam are presented which illustrate the appearance of various types of deformation- or growth- induced structural variations. Slip and lattice bending were detected in tensile tests for strains as small as 0.1 pct. Evidence of deformation bands, lineage structure, and void formation wns also shown. AmONG the most important methods of studying internal stresses in metals is the utilization of various X-ray techniques. The general subject of X-ray metallography has been treated in a most excellent manner by Taylor,1 and the use of X-rays for the direct observation of imperfections in crystals has recently been reviewed in an article by Newkirk2 and in the book edited by Newkirk and Wernick.3 Since the inception of metallographic X-ray analysis, there have been numerous technological developments and refinements, each with its particular advantages and disadvantages and, acrording to these, its particular applications. X-ray diffraction techniques can be divided into two general categories, that of X-ray diffraction microscopy and that of X-ray diffraction macroscopy. In the former are included such methods as those of Berg-Barrett, Lang, and Schultz2,3 which are concerned with microscopic imperfections such as dislocations. The second category includes all work concerned with the study of the condition of a crystal lattice structure as indicated by the marroscopic detail in its diffraction patterns. An example of this is the study of the diffraction manifestations of inhomogeneous plastic deformation as manifested by formation of deformation bands and inhomogeneous lattice rotations. The method used in the present investigation was an X-ray diffraction macroscopy technique. The geometry and analytical aspects of the method were similar to those of Julien and Cullity.4,5 The source was collimated with a single slit in a manner simi- lar to the "parallel beam'' method of Barth and Hosemann6 except that a continuous spectrum of radiation was employed. The apparatus produced large-beam transmission Laue patterns of thin cylindrical aluminum-wire crystals, which were deformed either in tension or torsion. Although the conventional X-ray target and interposed slit were not capable of the high resolution obtainable with a fine-focus X-ray source as employed in a microfocus apparatus, resolution was a secondary consideration in our technique, and was sacrificed to obtain sufficient intensity along a sizable length of the specimen. By using a grid indexing technique similar to that of Barth,7 we were able to study several diffraction lines from various planes simultaneously. The results of these tests give additional information with regard to the inhomogeneous deformation of single crystals, and the indexing procedure used provides a correlation between portions of the test specimen and portions of a diffracted beam. EXPERIMENTAL TECHNIQUE The experimental arrangement used is shown schematically in Fig. 1. A source of continuous X radiation from a vertically mounted Machlett X-ray tube possessing a copper target and operated at 20 kv and 10 ma was passed down a horizontal lead tube 80 cm long which terminated in an adjustable vertical brass slit. The slit opening was adjusted to correspond with the diameter of the test specimen. In front of the brass slit it was possible to place a screen wire mesh, one horizontal strand of which was a lead wire which served as a fiduciary mark, the screen itself serving as an indexing system as will be described later. Behind the screen was the test specimen which consisted of an aluminum single crystal wire 1/64 in. in diameter and 3 in. long. These 3-in.-long crystals were cut from

Jan 1, 1965

By Blamey Stevens

The object of this paper is to present a theory of the formation of fissures, which seems to be supported by all available data. The investigation is, in the main, an exact one, and irregularities of the rock-structure are generalized. From the conclusions drawn a general classification of fissures is made, and this should be of practical use in the comparison of mineral deposits. The theory also throws some light on the equilibrium of the earth's crust and the depth of action of surface-waters. Incidentally, additions are made to the theory of earthquake-slips. Former Theory. It has been previously pointed out that the "jointing" of homogeneous rocks occurs in two sets of planes, at right angles to one another, and making angles of 450 with the directions of greatest and least principal stress.' The theory by which this fact is explained does not, however, account for fissures and faults, because normal faults are usually more vertically, and reverse faults more horizontally, inclined than 450. The "jointing law" is based on the following axiom: In a homogeneous mass under pressure, rupture must take place on the lines of maximum tangential stress."2 This law applies, with fair approximation, to the tests on jointing which can be made in the laboratory, and as nearly as can be expected to the natural jointing-planes in rock-masses, where the stresses are not very great; but it entirely fails to account for fissure-fractures.3

Jan 1, 1910

By John B. Baker, Bernard B. Betty, H. F. Moore

For several years there has been in progress in the Materials Testing Laboratory of the University of Illinois an investigation of creep and fracture of lead and lead alloys. In the course of this investigation it has been shown that the phenomenon of creep occurs in part at the grain boundaries of lead and lead alloys. To study the occurrence of creep and the development of fracture within crystalline grains, two series of tests of single crystals of lead have been carried out. The first of these, a preliminary series, by Mr. Betty, has been described.l,2 The second, pursued by Mr. Baker for his doctoral dissertation, was carried out under the direction of Professor Moore, with the assistance of Prof. G. L. Clark in the X-ray work, and the cooperation and advice of Mr. Betty. This paper is based on the test data obtained in this second series. Single crystals of a very pure commercial lead have been prepared, some of them tested to measure creep, others tested to fracture under long-continued steady load, and still others tested under cycles of repeated tension. An interpretation of the test data of these single-crystal tests is offered, which is a combination of parts of several well-known theories. Specimens The single-crystal specimens were made from a piece of very pure commercial lead sheathing. A spectroscopic analysis of one of the single crystals showed the presence of 0.005 per cent Bi, 0.0001 per cent Cu and 0.0003 per cent Ag. Preparation.—The Bridgman method of casting single-crystal specimens was used.3 The specimens were cast to the shape and size shown in Fig. 1 (dimensions in Fig. 4c) in a duralumin mold. Molten lead does not stick to duralumin. Fig. 1 shows the mold and the blast flames for heating. After the mold had been heated to the temperature of molten

Jan 1, 1938

By John B. Baker, Bernard B. Betty, H. F. Moore

For several years there has been in progress in the Materials Testing Laboratory of the University of Illinois an investigation of creep and fracture of lead and lead alloys. In the course of this investigation it has been shown that the phenomenon of creep occurs in part at the grain boundaries of lead and lead alloys. To study the occurrence of creep and the development of fracture within crystalline grains, two series of tests of single crystals of lead have been carried out. The first of these, a preliminary series, by Mr. Betty, has been described.l,2 The second, pursued by Mr. Baker for his doctoral dissertation, was carried out under the direction of Professor Moore, with the assistance of Prof. G. L. Clark in the X-ray work, and the cooperation and advice of Mr. Betty. This paper is based on the test data obtained in this second series. Single crystals of a very pure commercial lead have been prepared, some of them tested to measure creep, others tested to fracture under long-continued steady load, and still others tested under cycles of repeated tension. An interpretation of the test data of these single-crystal tests is offered, which is a combination of parts of several well-known theories. Specimens The single-crystal specimens were made from a piece of very pure commercial lead sheathing. A spectroscopic analysis of one of the single crystals showed the presence of 0.005 per cent Bi, 0.0001 per cent Cu and 0.0003 per cent Ag. Preparation.—The Bridgman method of casting single-crystal specimens was used.3 The specimens were cast to the shape and size shown in Fig. 1 (dimensions in Fig. 4c) in a duralumin mold. Molten lead does not stick to duralumin. Fig. 1 shows the mold and the blast flames for heating. After the mold had been heated to the temperature of molten

Jan 1, 1938

NEW MEMBERS The following list comprises the names of those persons who became members during the period Jan. 10, 1919, to Feb. 10, 1919. ADAMS, FRANCIS SPEARMAN, Supt., Power Dept., Anaconda Copper Min. Co.; Anaconda Mont. ALDERSON, G. E., Min. & Met. Engr 1317 Sloane Ave., Lakewood, Ohio. BENJOVSKY, T. D., Min. Engr., Cons. & Constr 2045 Vine St., Denver, Colo. BROPHY, OSCAR, Met 1523 S. Broad St., Philadelphia, Pa. BUTTRAM, FRANK, Chief Geol., Fortuna Oil Co., 424 Liberty National Bank Bldg., Oklahoma City, Okla. COCHRAN, R. B., Mine Supt., The Teziutlan Copper Co., Aire Libre Puebla., Mexico. CONNAR, T. C., Civ. & Min. Engr. & Geol.; Chief Engr., Zanesville Coal Co., Zanesville, Ohio. DAVE, E. O Capt., Co. A, 212th Engineers, Camp Devens, Mass. FOLEY, CHARLES B., Electro-Met., Martin Rockwell Corpn., 347 Madison Ave., New York,. N. Y. HOSFORD, WILLIAM F., Asst. Tech. Supt., Western Electric Co., Inc., Hawthorne Station, Chicago, Ill. HOSTER, M. T., Supt., French Creek Mines, E. & G. Brooke Iron Co., St. Peters, Pa. KAWASAKI, SHIGETARO, Chief Geol., Geological Survey of Chosen, Government General of Chosen, Keijo. Korea.

Jan 3, 1919

By A. J. de Witte

It has been observed that upon invasion of a sand containing oil or gas and connate water by mud filtrate the hydrocarbons are more rapidly flushed by the filtrate than is the connate water.' In time, it appears that the following displacement pattern emerges: oil (or gas) is being swept ahead by connate water which, in turn, is pushed by invading fluid. Eventually the connate water may have "banked up" sufficiently to form a zone of appreciable thickness leading the invading front. In the extreme case, Fig. 1 shows how the situation will develop.' Immediately adjacent to the borehole (radius r) there is a zone, the invaded zone proper, where the connate water has been flushed out completely and which contains only residual oil or gas and mud filtrate. This zone (extending out to a radius ri) grades more or less abruptly into the next (thickness A), which contains only residual hydrocarbon and connate water. Beyond it, again more or less sharply bounded, extends the virgin formation with the original interstitial water saturation Sw. The various saturations are indicated in Fig. 1. The three zones generally will be marked by resistivity contrasts owing to their different fluid contents. As the connate water is usually more saline than the invading fluid, the second zone having a high connate water saturation forms a concentric cylindrical ring or annulus of low resistivity R, around the borehole.',' It will be referred to as the "low zone." Fig. 1 shows schematically the resistivity profile. It is clear that the phenomenon of a low zone could not occur in invaded water sands. The presence of a low zone, therefore, would be a qualitative indication of a hydrocarbon-bearing formation. Granted that the phenomenon is real, if it were pronounced enough to be detected, one might thereby have a means of locating oil or gas in the ground. This is the aim of the "displacement logging" method.' In any case, the presence of a low resistivity zone will affect the reading of electric logs. Using conventional log interpretation techniques, one must be aware of this and, if necessary, correct for it. Whether correction or detection should be the goal will depend primarily on the magnitude of the effect. The type of log which is likely to be affected most is the induction log. The current pattern of an induction log is concentric with the borehole. Any concentric ring of low resistivity, therefore, will tend to become crowded by current lines. This zone of maximum current density will obscure the relative contributions to the current conduction by other portions of a bed making, for instance, the contribution of the virgin formation less significant and thus detracting from the value or the induction log as an R, reading device. The present note is intended to ascertain the maximum possible effect of a low zone in the extreme case portrayed by Fig. 1 on three commercially available types of induction logs, sc., 5 FF 27, 5 FF 40 and 3 F 60. Type 5 FF 27 or 5 PF 40 is currently run in conjunction with a 16 in. normal and SP log. This combination is gradually replacing the regular electric survey (two normals and one lateral) as a standard log in many areas. On the basis of the scheme of Fig. 1 (sharp boundaries between successive zones), the thickness of the low zone may be computed for various amounts of infiltration measured by the ratio of invaded zone diameter to hole diameter D,/d. Referring to Fig. 1, we can set up a material balance for the water displaced from the invaded zone proper and the water present in the low zone. The volume of connate water displaced from invaded zone upon flushing by mud filtrate is: V1 = e p (r2 - r2) ? Sw . where c = bed thickness ? = porosity Su, = original connate water satu-ration. The volume of water finally accu-mulated in the low zone is: Vz = e p [(r1 -?)2 - r2 4] ? Sw . where SW1 = 1 — Sor = "water" saturation in the invaded and low zones both. The volume of water originally present in the low zone is:

Jan 1, 1958

By J. L. Bray

Lead has often been suggested as a protective coating for iron and steel. Such a protective coating should possess: (1) good adhesion, (2) durability, (3) ease of application, (4) freedom from pinholes, (5) good appearance and (6) low cost, but, unfortunately, lead coatings so far produced do not have all of these characteristics. Because of the necessity of carrying out the coating process cheaply, and because lead solutions have poor plating characteristics, most of the efforts have been directed toward the hot-dipping process rather than electroplating. The hot-dipping processes using lead have not been successful chiefly because of the lack of adherence between iron and lead. In any coating process involving iron a bond can be obtained only by the formation of an intermetallic compound, the formation of a solid solution, or mechanical means. Lead forms with iron two immiscible liquid solutions, and in the solid state no intermetallic compounds or solutions. It is necessary, therefore, to employ some other element or elements as a binding agent. Tin may be used as in terneplate, or copper in the form of a thin film of electrolytically deposited metal to which the lead will adhere. Because of its physical and chemical properties, lead as a coakkg medium would undoubtedly be limited in its use to sheet and wire and then only when the article is not subject to abrasion or wear. A very large tonnage of these products is being used under such conditions and a successful lead-coating process should be a valuable contribution to the science. Two other difficulties stand in the way of successful lead coating—that of poor appearance of the weathered surface and the tendency of the lead to form pinholes during solidification. Since lead is commonly accepted as cathodic to iron, these exposed areas are ones of accelerated corrosion. Use of Zinc.—The method under consideration involves zinc as a binding agent on both the steel sheet and in the molten bath. This

Jan 1, 1937

By Clarence Zener

The heat-treatment of steels will not pass from the stage of an art into that of a science until the mechanism of the phase transformations associated therewith is thoroughly understood. Such an understanding will involve two distinct types of inquiry: (I) the direction of the transformation, (2) the speed of the transformation. The first type of inquiry, which involves only the equilibrium relations between the various phases in steel, is the subject of the present and of a succeeding article; the second type, which involves the kinetics of transformations, will be the subject of a later article. In order that a theory of equilibrium relations may give useful information, certain experimental data must be put into the theory. It is customary for these data to be of a thermal nature. In the system discussed herein—steel—such thermal data are very scarce. In medium-alloy steels another type of data might possibly be used. In these steels the concentration of solute is so low that it may be possible to use the approximation of dilute solutions, an approximation that leads to linear relationships. The unknown functions, or constants, may then be determined in some cases from the binary iron-alloy system and in other cases from the ternary iron-carbon-alloy system. From the functions, or constants, so determined may then be computed the equilibrium relations in more complex medium-alloy steels. In the present article this second approach is used, the necessary experimental data 'being obtained from the simple binary and ternary equilibrium diagrams. Fundamental Equations In this article are derived the equilibrium relations between the gamma, alpha and cementite phases. In these three phases all important alloying elements except carbon form substitutional solutions, each alloying atom occupying a potential site for an iron atom. Carbon, on the other hand, forms an interstitial solution. In the face-centered cubic gamma phase, the interstitial positions are at the center of the unit cube and at the centers of the cube edges. There are therefore four interstitial positions per unit cell, or one per iron atom. In the body-centered cubic alpha phase, the interstitial positions are probably at the face centers, and also at the centers of the edges, which are crystallographically equivalent to the face centers. There are therefore six interstitial positions per unit cube, or three per iron atom. In cementite, (Fe, Alloy)3C, the carbon atoms may. be regarded as filling all the lattice positions of a given type. The introduction of the fundamental the of equilibrium has presented the author with a quandary. These equations are formally so similar to other equations that have been derived1,2 for related systems that they may appear to some readers

Jan 1, 1947

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for ' large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing 'lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By Clarence Zener

The heat-treatment of steels will not pass from the stage of an art into that of a science until the mechanism of the phase transformations associated therewith is thoroughly understood. Such an understanding will involve two distinct types of inquiry: (I) the direction of the transformation, (2) the speed of the transformation. The first type of inquiry, which involves only the equilibrium relations between the various phases in steel, is the subject of the present and of a succeeding article; the second type, which involves the kinetics of transformations, will be the subject of a later article. In order that a theory of equilibrium relations may give useful information, certain experimental data must be put into the theory. It is customary for these data to be of a thermal nature. In the system discussed herein—steel—such thermal data are very scarce. In medium-alloy steels another type of data might possibly be used. In these steels the concentration of solute is so low that it may be possible to use the approximation of dilute solutions, an approximation that leads to linear relationships. The unknown functions, or constants, may then be determined in some cases from the binary iron-alloy system and in other cases from the ternary iron-carbon-alloy system. From the functions, or constants, so determined may then be computed the equilibrium relations in more complex medium-alloy steels. In the present article this second approach is used, the necessary experimental data 'being obtained from the simple binary and ternary equilibrium diagrams. Fundamental Equations In this article are derived the equilibrium relations between the gamma, alpha and cementite phases. In these three phases all important alloying elements except carbon form substitutional solutions, each alloying atom occupying a potential site for an iron atom. Carbon, on the other hand, forms an interstitial solution. In the face-centered cubic gamma phase, the interstitial positions are at the center of the unit cube and at the centers of the cube edges. There are therefore four interstitial positions per unit cell, or one per iron atom. In the body-centered cubic alpha phase, the interstitial positions are probably at the face centers, and also at the centers of the edges, which are crystallographically equivalent to the face centers. There are therefore six interstitial positions per unit cube, or three per iron atom. In cementite, (Fe, Alloy)3C, the carbon atoms may. be regarded as filling all the lattice positions of a given type. The introduction of the fundamental the of equilibrium has presented the author with a quandary. These equations are formally so similar to other equations that have been derived1,2 for related systems that they may appear to some readers

Jan 1, 1947

By S. F. Urban, G. Derge

At the time this investigation was initiated variations were observed in the quality of different heats of basic electric-furnace steels, although they had been made under purportedly similar conditions. This indicated that these variations were related to normally unobserved variations in the character of the bath, especially during the "refining" period. Although the slags used for this operation are commonly referred to as "reducing" slags, and are regarded as having a "deoxidizing" action on the bath, no reliable measurements of this action were available. It was decided, therefore, to study the behavior of oxygen in the metal for ' large enough number of heats to learn its normal variations and to relate these variations to regularly observed conditions of operation. The most important general conclusion reached was that the time a heat is held under a reducing 'lag should be reduced to a minimum, which was about an hour and a half under the conditions studied. Beyond this time no observable beneficial effects are obtained from the reducing slags, insofar as oxygen and sulphur content of the bath are concerned. It is likely that added time may increase hydrogen content as well as heat costs. The oxygen content of the bath is never reduced below the amount in equilibrium with the carbon. Concurrently with this work, J. S. Marsh1 presented data that supplement and support many of the results of this paper. Procedure The work was done in two different electric-furnace shops of the same plant. The selection of heats was made primarily with regard to the convenience of heat schedules. companion slag and metal samples were taken just prior to slag-ofi and throughout the refining period for an initial set of 17 heats, and before slag-off and near tap for an additional I3 heats. slag Sampling presented no particular problem; a spoonful of slag was poured onto a metal plate and when sufficiently cool was sealed in an airtight container. Sampling the metal for oxygen presented a more complex problem. Because of the lack of previous experience in sampling electric-furnace baths, a number of methods were compared. Chilled Wedge Samples2 An unkilled metal sample is removed from the furnace in a well-slagged car-bometer spoon and poured immediately into a heavy copper mold designed to provide rapid freezing. Three different types of molds were used to determine the optimum for electric-furnace hats. The Big wedge Mold (a) was a 4 by 4 by 4-in. split copper mold, yielding a wedge-shaped casting I in. wide, 1 1/2 in. long, and 34 in. maximum thickness, and was finally adopted as the most satisfactory design.

Jan 1, 1948

By W. D. Robertson, Raymond C. Boettner

A study was made of the change in density during the first (transient) and second (linear) stages of the creep curve of polycrystalline copper as a function of 1) stress, 2) temperature, 3) plastic strain, 4) impurity and atmosphere effects, and 5) structure, including single crystals. Voids were not observed in single crystals strained 15 pct at 500°C, or in a polycrystal-line aggregate produced by recrystallizing a single crystal, within the limit of sensitivity, Ae/e = 1 x 10-4. It appears that voids are heterogeneously nucleated at grain boundaries by an insoluble phase, or phases, which can be removed by directional solidification. The principal controlling mechanism of void growth appears to be condensation of vacancies at grain boundaries. Vacancies are transported to a boundary and condense as a consequence of the tensile stress component across the boundary, which depends on the orientation and configuration of the boundary plane and on boundary shear across ledges and other irregularities. The ultimate source of vacancies is the free surface and diffusional transport is by way of the boundary plane. PREVIOUS investigations have dealt with the nucle-ation of voids at grain boundaries under creep condition~'-~ and with the connection between grain boundary voids and subsequent brittle fracture.5-7 Growth of voids during the creep process, particularly in the transient and linear stages of creep, has not been studied with the same intensity. Therefore, it seems pertinent to investigate the process of void growth with respect to the related creep curve, and the morphology of growing voids with respect to the structure.

Jan 1, 1962

By I. Iwasaki

The interaction of starch and calcium ions in soap flotation of activated silica from iron ores was investigated using the response surface method. The results were correlated with adsorption studies and into pilot plant tests. It was reported previously1,2 that in soap flotation of activated silica from iron ores there existed an optimum combination of the amounts of starch and calcium chloride addition, and that corn starch as a depressant for iron oxides became effective when a critical amount of starch was added, beyond which excess starch appeared in measurable quantities in the aqueous phase. Further, adsorption studies2,3 with various starch products on hematite or quartz showed that the adsorption of starch at a given pH was markedly enhanced by the presence of calcium ion in solution. From these observations it becomes of interest to investigate the interaction of starch and calcium added to the ore pulp, and their influence on the selectivity of flotation separations. This paper describes an empirical relation between such dependent variables as the grade and recovery of iron in the concentrate and the residual concentrations of starch and calcium ion in solution as a function of two independent variables, namely the amounts of starch and calcium chloride addition, as determined by using the general technique of response surface methodology. The results thus obtained are correlated with the adsorption studies on hematite and quartz, and with a typical pilot plant operation. MATERIALS AND METHODS The ore sample used in the batch flotation studies was the fine fraction of a Mesabi gravity concentrate produced by pilot plant grinding and classification. The sample analyzed 55.21% iron and 14.70% insol, and consisted of 85.81% minus 325 mesh (corresponding to Ore C). 2

Jan 1, 1965

By E. T. Turkdogan, Klaus Schwerdtfeger, P. Grieveson

The rate of growth of "Fe4N" on a iron was measured by nitriding purified iron strips in flowing am -monia -hydrogen gas mixtures at 504" and 554°C. It is shown that a dense nitride layer is formed when a zone -refined iron is used in the experiments. With less pure iron, the nitride layer is found to be porous. Through theoretical treatment, the self-diffusivity of nitrogen is evaluated porn the parabolic rate constant, and found to be essentially independent of nitrogen actirlity, e.g., D* = 3.2 x l0-12 and 7.9x l0-12 sq cm per sec at 504" and 554?C. Some consideration is given to the mechanism of diffusion in the nitride phase. THERE is a great deal of background knowledge on the solubility and diffusivity of nitrogen in iron, and on the thermodynamics and crystallography of several phases in the Fe-N system. Although case-nitrided steels have many applications in practice, no work seems to have been done on the diffusivity of nitrogen in the iron nitride, ?', phase. The only work reported on the related subject of which the authors are aware is an investigation by Prenosil,1 who measured the growth rate of the e phase on iron by nitriding in ammonia-hydrogen gas mixtures. EXPERIMENTS Purified iron plates of approximate dimensions 1 by 0.5 by 0.03 cm were nitrided in flowing mixtures of ammonia and hydrogen, in a vertical furnace fitted with a gas-tight recrystallized alumina tube. After a specified time of reaction, the sample was cooled to room temperature by withdrawal to the water cooled top of the reaction tube. The furnace temperature was controlled electronically in the usual manner within *l°C; the temperature was measured using a calibrated Pt/Pt-10 pct Rh thermocouple. For each experiment the iron strip sample was cleaned with fine emery cloth and degreased with tri-chloroethylene prior to the experiment. The ammonia-hydrogen gas mixtures were prepared from anhydrous ammonia and purified hydrogen using constant pressure-head capillary flowmeters. The gas mixture flowed upward in the furnace with flow rate of 400 cc per min at stp. The composition of the gas mixture was checked by chemical analysis at regular intervals. In most cases, the compositions of the exit gas and metered input gas agreed within about 0.3 pct, indicating that cracking of ammonia did not pose a problem at the temperatures employed. Two series of experiments were carried out using two different types of purified iron samples. In the first series of experiments at 550°C, vacuum carbon deoxidized "Plastiron" was used. The main impurities present in this iron were, in ppm: 4043, 50-Cr, 20-Zr, 40-Mn, 20-P, 20-S, 20-C, 50-0, and 10-N. In these experiments the rate data were obtained by measuring the change in weight of the iron specimen suspended in the hot zone of the furnace by a platinum wire from a silica spring balance. The nitride layer formed in these experiments was found to be porous, particularly near the outer surface. In other experiments, high purity zone-refined iron (prepared in this laboratory) was used. The total impurity content of this iron was 30 ppm of which 20 ppm was Co + Ni, 4 ppm 0, other metallic impurities were less than 1 ppm. The zone-refined iron bar, -2.5 cm diam, was cold rolled to a thickness of about 0.03 cm and the specimens were prepared for the experiment as described earlier. After the nitriding experiment, the sample was copper plated electro-lytically and mounted in plastic for metallographic polishing. After polishing, the thickness of the ?' layer was measured using a metallographic microscope. The nitride layer formed on the zone-refined iron was essentially free of pores. RESULTS The different morphology of the nitride layers grown on "Plastiron" and zone-refined iron is shown in Fig. 1. Both samples were nitrided side by side for 55 hr. The holes in the less pure iron, Fig. l(a), are confined to a region about one half thickness from the outer surface. The dense layer grown on zone-refined iron, Fig. l(b), is thinner than the porous layer on the "Plastiron". The impurities in the iron are believed to be responsible for the formation of a porous nitride layer. The pore formation may be due to the high nitrogen pressures existing within the nitride layer, e.g., the equilibrium nitrogen pressure is 1.2 x l05 atm in the 38.6 pct NH3-61.4 pct H2 and 6.6 x l03 atm at the Fe-Fe4N interface at 554°C and 0.96 atm. It is possible that the oxide inclusions present in the electrolytic iron may facilitate the nuclea-tion of nitrogen gas bubbles within the nitride layer. Support for this reasoning is the fact that pores are only encountered in the outer range of the layer where nitrogen pressures are largest. The photomicrographs in Fig. 2 show the effect of reaction time on the thickness of the dense nitride layer formed on zone-refined iron. These sections are from samples nitrided in a stream of 29 pct NH3-71 pct H2 mixture at 554°C for 22, 70, and 255 hr. In all the sections examined the nitride-iron interface was noted to be rugged. These irregularities are be-

Jan 1, 1970

By Eric K. Albert, J. Kiusalaas

The paper presents an overview of SPASID (Kiusalaas and Albert, 1983), a new computer program developed under U.S. Bureau of Mines funding for the prediction of surface subsidence caused by under- ground mining operations. The presentation, which is illustrated with two case studies, also re-evaluates the influence function method as a tool of subsidence prediction, arriving at some rather unconventional recommendations. SPASID consists of four modules that communicate through common data bases: (1) Preprocessor. This module prepares and maintains the database for the entire site. The database contains all the information about the site and the mine operation that is necessary for the computation of subsidence. (2) Subsidence Predictor. The influence function method is used to predict the surface displacements that occur in any portion of the site that occur between two given dates. The computations take into account the time lag between extraction and displacement, and the effects of pitching seams and incomplete compaction at the edges of panels. The program contains i not he's influence function and the Green's function of transversely isotropic elasticity theory. (3) System Identification. The purpose of System Identification is to determine the optimal values of the various parameters associated with the influence functions in the Subsidence Module. System Identification requires measurements of subsidence from a site with a sirnilar overburden structure. The values of the subsidence parameters are obtained by minimizing the discrepancy between the measured and computed surface displacements. (4) Postprocessor. The Postprocessor is a graphics facility for displaying the data generated by the other program modules.

Jan 1, 1984

By J. M. Davey

Lead-zinc sulphide ores at Mount Isa are currently treated at the rate of 180,000 long tons per 28 day period in the No. 2 Concentrator of Mount Isa Mines Limited. Prior to June 1966 lead-zinc ore was treated in part of the No. 1 Concentrator up to a rate of 70,000 long tons per period. Since 1955, two major changes in ore type being processed have occurred. Because of these changes, problems arising from treatment of the ore have altered and during the period several major changes in practice have been advocated and experimentally tested. Most of these flow sheets were developed with a view to overcoming one major problem in the ore. These were invariably abandoned as the Mount Isa lead-zinc ore contains a number of equally major problems all of which must be overcome in the treatment process. MINERALOGY The orebodies are situated in the Mount Isa Shale Group which is Proterozoic in age (Carpentarian System). The sediments consist dominantly of fine grained dolomitic, quartzo-feldspathic shales and siltstones. Specifically, the Mount Isa orebodies lie in the Urquhart shale formation which is characterised by sediments of high albite and orthoclase content denoting a large volcanic component. The Urquhart shales are approximately 3,500 feet thick and extend at least north and south of Mount Isa for 20 miles in each direction. In the area of the silver-lead-zinc orebodies the Urquhart shales are highly pyritic and have a relatively high carbon content. The

Jan 1, 1970

By G. O. Hiers

IN 1948 in the United States, 184,300 tons of lead was fabricated as coverings for electric power and communication cables. Such covering generally is called "sheathing" for the principal lengths of the cables, while the short lead encasements of the joints are called "sleeves." For the purpose of this paper, both lead sheathing and lead sleeving can fittingly be called lead tubing. In the United States in the same year, 34,262 tons of lead was consumed in making extruded lead pipes. Such pipe is employed frequently for water or chemical solution conveyance with gage pressures up to 100 psi. Consequently, the walls are thicker in ratio to diameter than is the case with the cable sheaths. For this discussion, lead pipes can be thought of as tubes or tubing. About 19 centuries ago, the Romans produced metallic lead of about 99.9 pct purity. Evidently this was cast in flat sheets of Y8-in. thickness, for instance. Such sheet of 10-ft lengths was bent around a removable core producing a tube somewhat oval in cross-section and with a typical internal diameter of, say, 3 in. This method of production necessitated a seam or longitudinal joint evidently made by casting the seam metal adherently. The seam metal, as analyzed recently, contains about 1 ½ pct Sn. Blow pipes were said to have been employed when the joint was made. Specimens of such pipe were found both in Italy and in the British Isles. It is believed the pipes conveyed water for drinking purposes and for baths. Numerous specimens are still in existence in a good state of preservation, due to lead's usual inertness in air or water. According to Claude E. Pearson,1 there were various stages in the evolution of lead extrusion presses for making tubes: I. First press by Joseph Bramah, 1797. 2-First successful press by Thomas Burr, 1820. 3-First bridge die press, J. and C. Hanson, 1837. In 1845, Wheatston and Crooke made the first lead sheathed electric cable. Flat lead strip was wound spirally around the insulated conductor. Overlapping edges of lead were soldered. Early cables were also made by pulling insulated conductors into 50-ft lengths of lead tube. Borel in France, and Wesselau are credited with devising the first presses for extruding lead sheaths directly on cables in 1879. In the United States, Eaton, in 188o, and Roberston, in 1885, introduced new presses of improved design. Following Cunningham's original idea of making lead traps and. bends in 1873, the presses apparently were improved and made successfully soon thereafter. Between the years 1930 and 1940, two continuous extrusion presses for lead were developed abroad. One apparently was originated by Dunsheath and made by the Henley Telegraph Works Co. The other was developed by the Pirelli-General Cable Co. CURRENT PRODUCTION In addition to the several descriptive chapters on lead extrusion in Pearson's book, the Metals Handbook2 recently described pipe, sheath, and collapsible tube production. The latter is by impact extrusion.

Jan 1, 1951

By J. M. Hassler

Nowhere can there be found a more misleading statement than the old one that "Iron can be manufactured cheaper in the South." During the past decade ironmakers and users of iron have heard varied and sundry stories of the wonderful resources of the Birmingham district, including abundant ore and coal fields, cheap labor, a wonderful climate and similar industrial Utopian statements. Birmingham represents the major portion of the iron business in the South, and as Birmingham fares so goes the iron business of the South. The intent of this paper is to shed some light on the actual conditions surrounding ironmaking in the South, especially in the Birmingham, or North Alabama, district. By a presentation of facts it is desired to point out that the "cheap iron" of the industrial South is a thing of the past, primarily because of increased labor cost and because labor is radically different in performance to what it was years ago. Also, because most of the raw materials needed in ironmaking that would be classed better than inferior are gone. Important Factors The several important factors that have been responsible for this change are : 1. Shrinkage of the iron business in the South. 2. Increased labor cost. 3. The development of the South, with an industrial trend, without a substantial increase of its own iron-consuming market. 4. Increased freight rates, which has narrowed the market that might be reached from this district. 5. Depletion of the better grades of raw materials, both ore and coal. Shrinkage of Iron Business in South.—Table 1 was prepared in early 1936 and revised in 1937, of blast-furnace units in the North Alabama district, considering the year 1936 compared with a maximum number of furnace units of previous years, the peak point being very near the year

Jan 1, 1937