Search Documents

By L. W. Holm, G. G. Bernard

Laboratory experiments were conducted to determine the effect of foam on gas flow in porous media. Previous studies have indicated that foam may be applicable as a restrictive agent in influencing underground gas flow. Foam was found to be exceedingly effective in reducing the permeability of porous media to gas. Consolidated and unconsolidated sands with specific permeabilities of 100 to 146,000 md had, in the presence of foam, gas permeabilities that were less than 1 per cent of the specific permeability; in many cases the gas permeability was practically zero. Foam reduced the gas permeability of loose sand to a much greater degree than that of a tight sand. For example, the permeability of a 125,000-md sand was reduced to 3 md while the permeability of a 4,000-md sand was reduced to 7 md. This effect should cause, to some degree, selective plugging of high permeability channels in various oil displacement processes. The presence of oil in a porous medium decreased the effectiveness of foam in reducing gas permeability; apparently oil acts as a foam depressant. However, it was found that certain foaming agents were very effective in reducing permeability even. in the presence of oil. Also, continuous injection of other foaming agents increased their effectiveness, when oil was present. The effect of foam on permeability of porous media to gas was studied as a function of foaming agent concentration and injection rate, absolute permeability, total pressure, pressure gadient, length of porous system, brine concentration and time. INTRODUCTION The use of surface active agents in flood water to increase the recovery of oil has been studied in the laboratory and in the field for decades, with rather limited success. In recent years a new approach to the problem was proposed. Instead of using an aqueous solution of surfactant as an oil recovery agent, Bond and Holbrook2 proposed that the oil recovery agent be a mixture of surfactant solution and gas. In their method, a water-soluble surface active agent with foam-producing characteristics is injected into an underground formation as an aqueous slug. This slug is followed by gas to produce a foam within the rock. Foams are defined as "agglomerations of gas bubbles separated from each other by thin liquid films'! A foam is fundamentally an unstable system. The foam process for oil recovery has since been studied by other investigators. Fried 1 has shown that foam can displace from porous structures oil that normally is unrecoverable by conventional water or gas drives. This superior oil displacing action is believed to be the result of several factors: (1) foam introduces into the reservoir many resilient interfaces of various sizes and curvatures, which increase the probability that a proper combination of forces for oil displacement will be created; (2) foam has appreciable viscosity which improves mobility ratio and contact efficiency; (3) foam accentuates the trapped gas effect because high gas saturations are possible without producing high gas/oil ratios. Deming4 studied the effect of various foam properties on the displacement of liquid. He found that (1) high foaming ability favors high displacement efficiency; (2) high foam stability is not necessary for high displacement efficiency; (3) displacement efficiency decreases with increase in plasticity of foam and (4) displacement efficiency is unaffected by surface tension of foaming agent solution. One of the important aspects of this oil recovery process is the effect of foam on gas permeability. The simultaneous flow of gas and liquid in porous media has been studied by numerous investigators and a large amount of literature exists on the subject. In this previous work, gas and liquid have generally been considered as essentially independent phases, whose flow characteristics are related through the saturation parameter. Foam, however, is a material with properties that are considerably different from those of its components; for example, the viscosity of a foam is greater than either of its components. Gas flow in a porous medium in the presence of foam should be considerably different

Jan 1, 1965

By Hsun Hu

Direct observations were made on the recrystalli-zntion of a cold-rolled (110) [001] crystal of 3 pct Si-Fe by annealing thin sections of the specimen inside the electron microscope during examination. Subgrain formation, presumably by polygonization, occurs rapidly, followed by a slow increase in the subgrain size before recrystallization can be detected. No migration of the subgrain boundaries was observed, and the formation of recrystallization nuclei by coalescence of subgrains is suggested. Re-c~ystallization characteristics of various texture components were individually examined. AS reported in a previous paper: orientations of the various deformation texture components in a 70 pct cold-rolled (110) [0011 crystal of 3 pct Si-Fe were completely confirmed by transmission electron diffraction patterns taken at various areas of the specimen. These orientations can be summarized as follows: Over most areas of the deformed crystal (111) planes are parallel to the surface. These areas correspond to either $- the two main defor: mation textures, the (111) [112] or the (111) [112].2-5 Within a few areas, (100) planes parallel to the surface are frequently found. These areas represent the minor deformation texture component, the (100) [Oll] type, which is derived from rotated Neumann bands.2'4'5 Only in very rare instances are (110) planes found parallel to the surface. This orientation corresponds to the very weak texture component of the (110) [001] type. In a pole figure, this (110) [0011 orientation is located within the orientation spread between the two main (111) [1121 type textures. Usually the electron diffraction patterns taken at various areas of the specimen are very simple ones, i.e., for any one area the pattern consists only of sharply defined spots of a single orientation. In some areas, however, more or less continuous rings of weaker intensities are superimposed on a simple pattern, indicating the presence of a wide range of additional orientations. In order to understand in detail the recrystallization of this cold-worked crystal, the recrywtallization characteristics of each of the various deformation texture components must be examined. This can best be done by using a high-temperature stage and transmission electron microscopy techniques, whereby small areas corresponding to the various texture components can be selected individually for examination. The present paper presents results obtained by this method. MATERIAL AND METHOD Specimens were prepared from a previously studied1 single crystal of a commercial grade 3 pct Si-Fe alloy with an initial orientation (110) [00l], cold-rolled 70 pct from 0.014 in. to 0.004 in. in thickness. Thin foils were prepared by electrolytic polishing as described in the earlier paper.' Specimens of this thin foil were then mounted in a high temperature stage similar to the one designed by Whelan.6 A direct current was used as the heating source. The temperature of the heating grid was calibrated by means of a Pt vs Pt-10 pct Rh thermocouple in a vacuum chamber (0.01 to 0.02µHg). Maximum variation within the temperature range of 250o to 000°C was about ± 25°C. After the desired areas were selected for examination, the specimen was heated to a low temperature for some time while the selected area was constantly watched. When no further change in structure and orientation could be observed, a higher temperature was applied. Photomicrographs and diffraction patterns were taken from time to time during examination, with the heater temporarily turned off* while the photographs were

Jan 1, 1962

[59H1-Water Law and Its Significance to the Mining Industry by Wells A Hutchins 59H2-Relation of Land Subsidence to Groundwater Withdrawals in the Upper Gulf Coast Region, Texas by Leonard A Wood and A G Winslow 59F3-Hydraulic Mining of Gilsonite and Its Application to Coal Mining by J H Baker 59H4-Recovery of Phosphates by In Situ Fluid Mining by Sylvain J Pirson 59F5-Coal Cleaning Plant Design for Minimum Operating Labor by Wm M Bertholf and John D Price 59F6-Coke Combustibility A Neglected Characteristic by J D Price 59B7-Union Carbide's Uranium Operation at Maybell, Colorado by K W Lentz and F T Temple 59H8-A Rapid Method for Estimating Alumina in Feldspathic Sands by Hugh H Bein 59H9-Water Laws as Related to Dredging in Idaho by Robert A Lothrop, Richard B Porter, and Robert P Porter 58B19-Separation and Washing of Alumina Process Residue by Morton Handelman 59B11-Feed Preparation and Froth Modification for Fatty Acid Flotation by Carl C Martin and Burt C Mariacher 59B12-Design Requirements for Tailing Disposal in the Southwest by E Vern Given 59B13-Semi-Dome Shaped Buildings for Bulk Storage by Edward E Ives and William L Payne]

Jan 1, 1961

By A. J. Phillips, C. G. Grant, Wm. B. Price

Admiralty nickel is a new corrosion-resisting and heat-resisting white metal alloy composed of 70 per cent. copper, 29 per cent. nickel and 1 per cent. tin. It has been given the trade name "Adnic." In 1924, Wm. B. Price' described this alloy and its successful use as a diaphragm metal. The physical properties of Adnic at ordinary and elevated temperatures were given in Mining & Metallury.~ A patent3 was granted on Adnic, April 28, 1925. Work was first started on this alloy during December, 1921. An investigation of the patent situation in this country and abroad, and also a search of the literature, did not reveal any work on the ternary diagram, copper-nickel-tin; and the only wrought copper-nickel-tin alloy found was that known as "Newloy," composed of copper, 64 per cent.; nickel, 35 per cent.; tin, 1 per cent. This was being manufactured and sold by Wm. Gallimorr & Sons, Ltd., Sheffield, England, for unplated spoon and fork stock, and first came to our attention in January, 1922. The preliminary work in connection with the development of Adnic was started by casting four binary copper-nickel alloys of the compositions shown in Table 1. Various a~ilounts of tin were added to each of these mixtures, to produce the series of ternary copper-nickel-tin alloys also given in Table 1. A 200-gm. sample of each of these was cast by iiielting in a clay graphite crucible and allowing the melt to slowly cool with the furnace. A longitudinal section from each of thcsc castings was polished and etched for examination. The castings were not homogenrous solid solutions, but showed the usual cored structure associated with cast alloys. Howcvrr, frorn an exarrlination of these sections we roughly determined

By M. G. Corson

UNTIL recently, the characteristics of cast copper have seldom been studied and such study as has been made has been inadequate. The prevailing idea seems to be that since pure copper is infrequently used in the cast state, there is no reason for trying to establish precise data regarding the properties of the metal in that condition. On the other hand, wrought copper either in the shape of sheets or wire rarely fails in service, except as a result of the action of reducing gases at the annealing temperatures, so there is little incentive to study the properties of the cast shapes -cakes, bars, ingots and billets-for the sake of tracing the causes of failures of the wrought metal to the cast stock. However, about a decade ago, wirebars of American origin often cracked badly while being hot-rolled in mills in Germany. This led to four investigations: by E. Seidl and E. Schiebold,1 by P. Siebe,2 by 0. Bauer and G. Sachs,3 and by G. Welter.4 These authors came to the conclusion that failures in hot-rolling were due essentially to the presence of a' wide zone of columnar crystals between the thin layer of fine crystals near the surfaces of the bars and the large but more nearly: equiaxed grains of the central core. This macrostructural defect was explained in turn by the probable upward deviation in the temperature of the metal while it was being poured into the molds of the casting machine. More recently, cast shapes of copper were investigated by N. P. Allen5 and by C. Blazey.6 Allen examined vertically cast wirebars and horizontally cast wedge cakes of electrolytic tough-pitch copper, but only for the distribution of densities; i.e., porosity. Blazey was interested mainly in the mechanism of the variations in electrical conductivity due to cold-work and anneal, but gave introductively an account of the composition and average densities of the tough-pitch horizontally cast wirebars used. As far as the present writer can tell, no investigation was undertaken for the sake of presenting a picture of the distribution of mechanical characteristics in the wirebars of copper, tough-pitch or otherwise.

Jan 1, 1938

The Colorado School of Mines, Golden, Colo. M F Coolbaugh, President. Since 1906 the School of Mines has issued a journal, known as the Quarterly of the Colorado School of Mines, which carries many articles on matters of general interest as well as other articles of a technical nature There is no regular subscription price to the School of Mines publications Anyone interested in back numbers should write and find out the conditions under which individual copies may be obtained, whether a price is set on them or whether they are free Some back numbers are not now available but efforts will be made to supply copies from the files of alumni or other friends of the School Vol 23, No. 3 of the Quarterly (July, 1928) is an index of the publications complete from July, 1906 to July, 1928. A selected list of the technical articles appearing in the Quarterly is given here: Vol 3, No. 3, Rare metals. uranium and vanadium, by H. Fleck (1909), vol 3, No 4, Tungsten in Colorado, by H R Van Wagenen, vol 4, No 3, Preliminary report of the radioactivity of the carnotite of southwest Colorado, by H Fleck and W. G Haldane (1909), vol. 8, No 1 (1913), Some recent developments at Leadville, by G. M Butler, vol 8, No. 3, Physiography of

Jan 1, 1933

By Robert Ammon

THE purpose of this paper is to present a brief sketch of the development of this hindered-settling classifier, but primarily to show the actual results obtained in practice with the classifier working on the Butte copper ores at the Boston & Montana Concentrator, at Great Falls and the Washoe Concentrator at Anaconda. The writer has endeavored to be as brief as possible, giving only the essential figures showing the efficiency of the classifier and leaving considerable interesting information to be derived by the reader from the statistics given. The paper deals with the practical work of the classifier under the following heads: 1. Desliming 4.0-mm. primary feed, overflow from 0.07 to 0.0 mm. 2. Desliming 1.25-mm. secondary feed, overflow from 0.07 to 0.0 nun. 3. Desliming Huntington Mill discharge, overflow from 0.07 to 0.0 mm. 4. Classifying 2.5-mm. deslimed secondary feed, overflow from 1.00 to 0.07 mm. 5. Classifying 2.5-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 6. Classifying 4.0-mm. deslimed primary feed, overflow from 0.75 to 0.07 mm. 7. Classifying middling-tailing product from roughing tables, overflow coarse tailing. 8. Classifying 2.5-mm. trommel undersize, not deslimed, overflow from 0.75 to 0.0mm. 9. Remarks on the inner feel cone. In the following pages all overflows, are given in quartz dimensions; i.e., by a 0.75-mm. overflow 'is meant an overflow whose maximum particle is a 0.75-mm. quartz grain. By the term "slime" is meant all material which will pass through a 200-mesh screen whose average opening is 0.07 mm.

Jan 8, 1913

By W. I. Garms, J. L. Stevens

BECAUSE of the many conflicting opinions regarding the functioning of the ball load and the characteristics of ball wear in ball-mill grinding, the following resume of reports covering recent tests conducted at the Hayden plant of the Kennecott Copper Corporation is submitted with the view of pointing out certain salient features that should throw additional light on the subject. MILLS USED Cylindrical drum mills with trunnion feed and discharge were used. The discharge trunnion was I3 1/2 in. in diameter. Dimensions inside the lining were 6 ft. 6 in. in diameter and 9 ft. 6 in. long. The mills were Britannia-lined and nine lifter bars projected 2 in. from the lining. The mill speed was 16 2/3 r.p.m. Feed to the mill was 9 per cent on 10-mesh, 85 per cent on 100-mesh, 77 per cent solids. New balls measured 2 in. in diameter and the approximate weight of the ball load was 40,000 pounds. INITIAL TEST During a test that was being conducted to determine the relative economic value of standard cast balls vs. forged steel balls in the local grinding operation, certain observations were made in regard to the functioning of the various ball sizes and the characteristics of ball wear, which warranted a supplementary test for the purpose of confirming such observations. For the initial test, the necessity for developing a graduated load of the new forged balls before the test could be started was realized, but the time required to obtain a graduated load and the functioning of the various ball sizes was not clear. No advantage could be seen for starting out with a full load of forged balls, as this initial load, at the least, would have to be completely ground out and replaced by daily additions of balls before the graduation could be complete and a normal static condition of ball sizes reached. For a considerable period prior to exhaustion of this initial charge there would be an unusual quantity of worn balls of a certain size, which would not be typical of a normal charge and could influence the characteristics and functioning of the entire load. Therefore, it was decided to start by daily addition of the forged balls to a mill that contained a normal operating load of cast balls. After 88 days of operation the mill was shut down for inspection. By that time the load consisted of a mass of forged balls functioning around a large core of the residual material of the former cast-ball load. This core of cast slugs, locally referred to as "the kidney," was well defined from the forged-ball load.

Jan 1, 1946

By A. T. Sweet, C. E. Plummer, H. W. St. Clair, S. F. Ravitz

The ammonium sulphate process for recovering alumina from clays was proposed by Rinman, Buchner, and others many years ago, and more recently various modifications have been investigated both here arid abroad.l-Is The process, as it is being investigated by the Bureau of Mines, involves the following essential steps: (I) sulphating the alumina in the clay by baking with ammonium sulphate at approximately 4m°C., (2) leaching with water to extract aluminum sulphate and ammonium sulphate, (3) crystallization of ammonium alum, (4) conversion of the alum to aluminum hydroxide by the ammonia gases given off during the baking, and (5) calcining the aluminum hydroxide to alumina. The over-all reaction between kaolinite (the most important alumina mineral in most clays) and ammonium sulphate during the baking step may be expressed as follows: Al2O8.2SiO2.2H2O + 4(NH4)2SO4 = (NH4)2SO4.A12(SO4)3 + 6NH3(g) + SH2O(g) + 2SiO2 [i] There is definite evidence. as is shown later. that the aluminum occurs in the baked product as anhydrous ammonium alum rather than as aluminum sulphate, provided the baking temperature is not much above 4o0°C. It is probable that the reaction takes place in the following steps: (NH4)2SO4 = NH3 -(- NH4HSO4 [2] Al2O3.2SiO2.2H2O + ;}NH4HSO4 = A12(SO4)3 + 3NH3 + 5H2O + 2SiO2 [3] A12(SO4)3 + (NH4)2SO4 = (NH4)2SO4.A12(SO4)3 [4] In onc modification of the process, the ammonium sulphate is first decomposed according to Eq. z, and the clay is treated with the resultant ammonium acid sulphate. Reaction I is highly endothermic. On the basis of the best available data, the following values have been estimated for the changes in heat content and free energy in calories per mol: -AH = 331,040 - 34T -AF = 331~040 - 78.3T log T - 671.8T The heat required' at 25OC is 320,900 cal. per mol, or 5650 B.t.u. per pound of alumina. The theoretical equilibcium pressure of NHa, based on the free-energy equation given above, increases very rapidly as the temperature rises above 3o0°C., and reaches one atmosphere at 43s°C. Ammonium alum solutions are almost ideal for crystallization. A saturated solution of ammonium alum contains 126. grams of AlzOa per 1000 grams of water at 90°C. and only 16.5 at 20 C. Hence most of the alum crystallizes out when the

Jan 1, 1944

By William E. Ford, Edward Salisbury Dana

General Principles of Optics Optical Instruments and Methods General Optical Characters of Minerals 1. Diaphaneity 2. Color 3. Luster Special Optical Characters of Minerals belonging to the different Systems A. Isometric Crystals B. Uniaxial Crystals General Optical Relations Optical Examination of Uniaxial Crystals C. Biaxial Crystals General Optical Relations Optical Examination of Biaxial Crystals 306. Before considering the optical characters of minerals in general, and more particularly those that belong to the crystals of the different systems, it is desirable to review briefly some of the more important principles of optics upon which the phenomena in question depend. For a fuller discussion of the o tics of crystals, special reference is made to the works of Groth (translation by Jackson), Liebisch, Mallard, Duparc and Pearce, Rosenbusch (translation by Iddings), Iddings, Johannsen, Winchell, mentioned on p. 3 also to the various advanced text-goks of Physics. 307. The Nature of Light. - Light is now considered to be an electro- magnetic phenomenon due to a periodic/variation in the energy given off by vibrating electrons. This energy is transmitted by a series of periodic changes that show all the characters of ordinary wave phenomena. The light waves, as they are commonly called, possess certain short wave-lengths that are of the correct magnitude to affect the optic nerves. Other similar waves with longer or shorter wave-lengths belong to the same class of phenomena. Immediately beyond the violet end of the visible spectrum come the so-called "ultra- violet" waves with still shorter wave-lengths and on beyond these we have the X-rays and the "gamma" rays produced by radium. Of the waves having greater lengths than those of light waves we have the waves that give

Jan 1, 1922

By C. L. Shapiro, R. Schempp

DuRing the past few years, general interest in the steel-producing and steel-consuming industries has been centered on the so-called "inherent characteristics" of steels. While often vaguely described, these characteristics are known to influence the response to heat-treatment and the hardening characteristics of the material. Although most of the recent papers and discussions have associated the "inherent characteristics" with the austenitic grain size and emphasized the importance of it, comparatively little is known of the variables that may affect the size of the austenite grain. The work to be described in this paper was carried out during the course of a study on the inherent characteristics of tool steel containing one per cent carbon. The discrepancies encountered in the determination and classification of the austenitic grain size led to an investigation of some of the variants influencing the austenitic grain size as determined by standard methods. Methods of Determining Austenitic Grain Size The present methods used for the determination of the austenitic grain size may briefly be classified in two groups: 1. Etching at room temperature to reveal the austenite grain size prior to cooling. 2. Etching at elevated temperatures, cooling to room temperature, and observing the structural conditions that existed at the temperature from which cooling occurred. The outstanding methods of the first group are: (1) the McQuaid-Ehn test, (2) optimum rate of cooling, (3) quenching and etching. McQuaid-Ehn Test.—This established and accepted test does not need much elaboration. It consists of pack carburizing at a definite temperature for a standard period of time and slowly cooling in the furnace. The temperature is 1700" F. (925' C.) and the time is 8 hr. The interpretation and evaluation of this test are fairly well defined in the A.S.T.M.

Jan 1, 1937

By L. G. Austin, P. T. Luckie, R. R. Klimpel, R. S. C. Rogers

1. INTRODUCTION The Bond method(1.2) for sizing tumbling ball mills has been used successfully for many years. The primary purpose of the Bond calculation is to predict the mill size and mill power to give a desired capacity (Q tph) from a wet overflow ball mill in normal closed circuit operated with a circulation ratio of 2.5. The input to the calculation is the make-up feed size characterized by the 80%-passing size in micrometers (xG), the desired circuit product size characterized by the 80%-passing size (xQ), and an empirical grindability number (the standard Bond Work Index) determined by a standard test. A series of empirical correcting factors(2) are used to convert the results to open-circuit or dry grinding in grate discharge mills. The Bond method has two major engineering advantages: (i) it is very simple; (ii) experience has shown that it works for many circumstances, as a reasonable approximation, because it is based on direct conversion of test data to results measured on industrial mills. There are four main disadvantages of the Bond method. First, there will be a range of error for any specific mill and material and set of operating conditions because the method does not explicitly include several variables which are obviously important: (i) recycle ratio and classifier efficiency (ii) mixture of ball sizes in the mill (iii) variations of residence time distributions with mill geometry and slurry density (iv) lifter design (v) slurry rheology (vi) different underfilling or overfilling of the mill as flow rate is changed. Second, the Bond method explicitly assumes that specific grinding energy E is not a function of ball load, whereas industrial practice and laboratory tests(3) show that the specific grinding energy (to go from a specified feed to a specified product) is less for lower ball loadings than the ball loading for maximum mill capacity. Third, the method uses only the 80% passing size of circuit feed and product to characterize the size distributions, whereas mill capacity in general must depend on the shape of the feed size distribution and the product size distribution. The prime example of this is the use of the reverse closed circuit which removes some fraction of the make-up feed before it is

Jan 1, 1982

NEW YORK SECTION ALLEN H. ROGERS, Chairman, H. C. PARMELEE, vice-chairman, FOREST RUTHERFORD, Vice-chairman, W. S. DICKSON, Secretary, 71 BROADWAY, NEW YORK, N. Y. J. E. JOHNSON, JR. F. T. RUBIDGE, Treasurer, P. G. SPILSBURY A meeting of the New York Section was held at The Machinery Club on Friday evening, Oct. 4, 1918, The Chairman, Allen H. Rogers, presiding. The CHAIRMAN.-MOST of us, I suppose, have been affected more or less by The request of The Fuel Administration that we leave our automobiles standing in The garages on Sundays. We shall all be interested in hearing about The situation that has called forth This, request, and The Oil Administrator, Mr. Requa, has kindly come from Washington to Tell us about it. MARK L. REQUA.-I am very glad To Tell you about the oil problem during This war period. The United States is supplying by far The greater part of all The petroleum products consumed in Great Britain, France and Italy. In addition To This, we have had To supply a marked increase in our domestic consumption, not only of The refined products, but of fuel oil as well. The combination has put a strain on The oil industry, which it is very difficult To meet. The oil companies, being under contract, had no option as To who should get Their oil first, and They were delivering pro rata To everybody; manufacturers of furniture were getting oil with The same regularity as Those who were making aeroplanes or munitions, and The oil companies felt that something should be done. The first order with which I had. anything To do was The priority list for The delivery of fuel oil. That list contained 12 classifications, beginning with bunker fuel and railroads, and you will realize The complexity of The situation when you hear that munitions plants are in class 11. The priority list held during The winter, but transportation became so bad, because of The number of ships that were Taken for trans-Atlantic use, that some of The oil companies were not able To deliver more Than about 60 per cent. into class 5, and nothing beyond that point. To add To the Troubles, the Tank-car mileage fell off. The average for 1917 was about 36 miles per car per day. in January, 1918, it dropped To about 8 miles, and it must have been nearly zero in The early part. of February. Because of The extremely severe winter, furthermore, pipe lines were not delivering anywhere near Their normal capacity. A new priority list has recently been promulgated, introducing a few slight changes. Natural gas has been brought under its provisions, and it has been extended To include The Pacific Coast, which was not considered necessary last winter. The situation in The gas industry is not satisfactory; it is estimated that There will be a decrease of 10 To 20 per cent. in The quantity of natural gas available This winter, as compared with last winter.

Jan 11, 1918

By A. E. Dwight, P. A. Beck

A search was made for ordered phases of AB3 composition in various combinations of Ti- and V-group elements with CO-and Ni-group elements. Three new TiNi3-type phases ZrPd3, HfPd3, and HfPt3 were found. In addition, twelve new Cu3Au-type phases TiRh3, Tilr3, ZrRh3, Zrlr3, HfRh3, Hflr3, VRh3, VIr3, CbRh3, Cblr3, TaRh3, and TaIr3 were also found. The lattice contraction for all three structures considered increases with increasing relative size of the A atom, suggesting that it is mostly the A atom that cont~acts. It was noted that, for the same radius ratio the lattice contraction is larger when the A atom is Ti than if it is Cb OY Ta. It is well known that elements or disordered solid solutions, which have structures with spherical close-packing, may be described in terms of various stacking schemes of close-packed layers. Stacking of the type abab corresponds to the hexagonal close-packed structure, and stacking of the type abcabc corresponds to the face-centered-cubic structure. In binary alloys of the first, second, and third long period transition elements various AB3 phases occur with close-packed ordered structures. It was observed that these ordered structures also may be described by suitable stacking of close-packed ordered layers, Fig. 1, as first shown by Laves and Wallbaum for TiNi3.' It is clear that the units of translation in such a close-packed layer consist of four atoms, one of which (black circle) is atom A and the three others (empty circles) are atoms B. Because of the alternation of A and B atoms in every second row of each layer, the unit-cell dimension in the layer is equal to the sum of the diameters of atoms A and B: a0 = 2(rA + rB). Stacking of such layers in the sequence abab results in a hexagonal close-packed structure of the MgCd, type. The unit-cell dimension in the basal plane is approximately double of that for the disordered hexagonal close-packed structure, but in the direction of the hexagonal axis it is about the same, so that 2co/uo = 1.63 in case of spherical close-packing. Ordered hexagonal close-packed structures of this type were found to occur in MoCo3,2 WCo3,, and UPt, .4 When the ordered layers shown in Fig. 1 are stacked according to the scheme abcabc, the resulting ordered structure is of the AuCu, type (cubic). Structures of this type were found to occur in TiPt3,5 CrPt,,' CrIr,,' and URu, .4 Finally, the stacking scheme abacabac of the same ordered layers results in a hexagonal close-packed structure of the TiNi3 type.' In this case, the unit-cell dimension is doubled not only in the basal plane, but also in the direction of the hexagonal axis, so that co/ao = 1.63. Structures of this type were found to occur also in TiPd3,5 ZrPt,," and UPd,.4

Jan 1, 1960

By Arthur C. Green

A group of 13 cities situated in Los Angeles and Orange counties in Southern California is engaged in constructing an aqueduct to carry water from the Colorado River at a point near Parker, Arizona, to a distribution point near Riverside, California. The aqueduct will have a total length of approximately 241 miles, and is designed to deliver 1605 cu. ft. of water per second, or a little more than one billion gallons per day. The aqueduct crosses a barren, desert waste and the project includes approximately 91 miles of 16-ft. tunnel. The large amount of tunnel driving that has been done in this country in the past few years has resulted in some remarkable developments in equipment and methods. The building of the Colorado River Aqueduct,, with its 91 miles of tunnels, has called on the best engineering knowledge in the country. New and better equipment has been designed for all phases of the work, and this equipment has been coordinated and adapted to the various conditions with a high degree of efficiency. The result has been that records for tunnel driving have been set under adverse natural conditions that exceed the estimates for progress under good conditions. All of the tunnels in the main aqueduct, except the Valverde and Bernasconi at the western end, have a finished diameter, inside the concrete lining, of 16 ft. Fig. 4 shows a section of the tunnel with the concrete lining in place. Fig. 5 illustrates the finished tunnel in three typical sections. The standard tunnel grade is 3.432 ft. per mile in the 16-ft. tunnels, but the Valverde and Bernasconi tunnels have a steeper grade and a finished diameter of 15 ft. 3 in. The rough bore of the large main aqueduct tunnels averages 12.95 solid cubic yards of material per foot of advance in timbered sections and 10.76 solid cubic yards per foot in unsupported sections. Tunnel Driving While the Conway mucker has been used on tunnel work for years, a larger and more powerful Conway was designed to meet the require-

Jan 1, 1937

By John W. Cahn

Tile avevage value of the mean curvature of surfaces in a specimen can be precisely delermined by sitrlple measurements performed on random sections or on 1 vojectiotzs of these surfaces. For surjaces enclosing particles, the quanlity is sllown to be velated to the probable tlurrrhev ot particles intevcepted by a random platne and, under certain conditions, to the perimeter of their Projected image and to the increuse in surjace area when the particles grow. Many of the velalionsl~ips are valid for any shape or size of the particles. THE recent growth of the field of stereology or quantitative microscopy is largely the result of the discovery of a limited number of rigorously defined geometrical parameters that can be precisely measured on random sections or projections of a structure without assumption about particle shape.' Such parameters have been the volume fraction and surface area and line length in a unit volume. The present paper introduces the average of the mean curvature of surfaces in a volume, and shows that it can be rigorously measured by counting methods alone. AVERAGE CURVATURE ON A PLANE Consider a curve y = v (x) on the xy plane. The curvature Kp in the plane at any point is given by Kp = (dZy/dx2)/[1 + (dy/dx)2]3/2. The average curvature along the curve may be defined as Kp = (1/L) fKpdl |1] where dl = [(dx)' + {dy)2]1/2 is the length of an element of the curve and .(dl = L is the total length of the curve. The integral on the right-hand side of Eq. [l] will be called the total curvature, It is dimensionless and readily evaluated by substituting d = arctan (dy/dx) to give ah which is the change in direction of the tangents to the ends of the curve, Fig. 1. Hence, Kp = (1/L)(?h) [2] It can also be seen that Eq. [2] is applicable in the limit of sharp corners. Even though the curvature is infinite at a corner, f Kpdl remains integrable and equal to the change of angle. The signs of the quantities Kp and dl are arbitrary and, if the areas adjoining the curve are equivalent, there seems to be no compelling reason to fix the signs. For a closed curve, however, it becomes worthwhile to use the signs to distinguish among different types of areas or phases enclosed. For such a closed curve AO = t2r and As a convention, we shall take the direction of the integration along the curve in such a way that the area or phase under consideration (henceforth called a) is kept to the left side of the curve, Fig. 1. Then Kp is positive where the curve is concave and negative where the curve is convex. For a closed curve Ad - +2n if the curve encloses a, and Ad = —2n if the curve is surrounded by a. PLANAR SECTIONS OF THREE-DIMENSIONAL STRUCTURE OF ISOLATED a PARTICLES Consider next a planar section of a microstructure containing particles of a in a matrix. We place no restriction on shape of connectedness of these particles, and begin by considering the curvature of only the boundary between a particles and matrix' Clumps of contiguous a particles are then treated as a single a particle. The two-dimensional section will show in a unit area na simple closed curves enclosing a particles and nh closed curves of holes, in-

Jan 1, 1968

By M. T. Simnad, C. E. Birchenall, M. H. Davis

The transport mechanisms previously proposed in wustite and hematite have been confirmed by movement of inert markers during the growth of these phases. By similar measurements the mechanism for magnetite has been determined. The rates of growth of multilayer scales on iron, magnetite and hematite on wustite, and hematite on magnetite have been measured. All rates are found to be diffusion controlled under the conditions of the experiments. MANY studies have been made of the rate of oxidation of iron in both the low temperature, film-forming region and the high temperature scaling range. The interpretation of the results has been greatly complicated by the formation of multi-layered scales containing the various phases of iron oxides. In most cases no attempt has been made to determine the composition of the scale and its dependence on time of oxidation in a quantitative manner. However, several recent studies'" have taken this variable into account. It is generally agreed that the growth of thick scales on iron follows a parabolic rate law for the increase of total thickness. In the thin film region agreement has been claimed with parabolic equations of various forms and with logarithmic equations. The discussion here will be concerned only with the formation of scales of considerable thickness, greater than several microns, although some of the conclusions may be applicable to thin films. A brief survey will be given of the solid phases of the iron-oxygen system, the stability of wiistite in bulk and in thin films, the relative densities of iron in the metal and oxides, and the kinetics of forma- tion of oxide scales on iron. New experimental results will be introduced at several points during the discussion, and an attempt will be made to formulate a mechanistic picture consistent with these observations. The experimental techniques are described in an appendix. Iron-Oxygen System Fig. la shows the iron-oxygen phase diagram. Wüstite ("FeO"): The lowest of the oxides has a NaCl type cubic lattice formed by close-packing of the relatively large oxide ions with the smaller iron ions arranged in the interstices. The ionic radius for 0' is about 1.3 A, while Fe++ has a radius of about 0.8A and Fe"' about 0.7A. Its range of existence on the phase diagram is very wide for an ionic material of this type and does not seem to include the stoi-chiometric composition FeO. These deviations appear to be well established as vacancies on iron lattice sites by the comparison of lattice parameters and densities for a series of compositions by Jette and Foote.4 The limits of the field are disputed, but the work which seems most reliable" indicates vacancies in from 5 pct to more than 12 pct of the iron sites. In order for the crystal to be electrically neutral, there must be electron holes which correspond to the formation of trivalent iron ions equal to twice the number of vacancies. Magnetite ("Fe³O4"): Considerable disagreement also exists in the literature about the stable range of the Fe³O4 field. Some diagrams show the Fe³O4 composition to be lower in oxygen than the formula indicates, but Schenck6 gives a diagram from the

Jan 1, 1952

AN intermetallic compound, Ni3A1, has an ordered fcc structure of type Ll2, and shows peculiar dependence of the yield stress upon temperature; i.e., the yield stress increases by a factor of six upon raising the temperature from 77" to 900K1, 2 This compound is technologically important, since many nickel-base superalloys owe their high-temperature strength to the peculiar yield stress behavior of Ni3Al. The only study of the elastic behavior of this compound was made by Davies and Stoloff,1 who determined Young's modulus of poly crystalline Ni3A1 between 300" and 730°K. The determination of single-crystal elastic constants of Ni3A1 is therefore of interest in connection with dislocation dynamics and is reported in this paper. A single-crystal specimen, 1 by 1 by 3 cm, was cut from an ingot generously supplied by Dr. B. H. Kear of Pratt & Whitney Aircraft. Following initial machining with a Servomet and a surface grinder, the specimen was etched and annealed at 1100°C for 5 hr in vacuum followed by furnace cooling. Two parallel faces were oriented normal to within ±l deg of a [I101 crystallographic axis by the back-reflection Laue technique. The parallel faces were hand-lapped, etched, and polished by the usual metallographic procedures. Final thickness along the [I101 axis was (0.9325 * 0.0005) cm. Chemical analysis gave an average composition of 87.35 pct Ni. Total impurity content is esimated to be no more than 0.1 pct. The elastic constants were calculated from measurements of ultrasonic waves which were propagated along the [110] axis. A longitudinal wave and two shear waves whose displacements are aligned along the [ 110], [li~], and [001] directions, respectively, are necessary in order to completely specify the three elastic constants. Two 3/6-in. quartz transducers were bonded to the parallel faces of the sample with ~ac-seal.3 Although this bond was sensitive to thermal shock, it performed satisfactorily over the entire temperature range for both longitudinal and shear wave propagation. A frequency of 5 mHz was employed in the method of Williams and Lamb4 in order to measure the absolute value of the ultrasonic velocity. The pulse-overlap technique of Mcskimin5 was also used at this frequency in order to determine the shift in the ultrasonic velocity

Jan 1, 1970

By Henry Louis

Henry Louis, Newcastle-upon-Tyne, England (communication to the Secretary*).—In this paper Mr. Simons derives the various forms of revolving slime tables, of which the Harz and the Linkenbach tables are typical examples, from the old rectangular or box buddle. This I believe to be an error, at any rate if Mr. Simons attaches the same meaning as I do to the ((evolution" of a dressing appliance. By the '(evolution" of such an appliance I understand the progressive development and improvement of an appliance acting on a definite principle, such improvements having usually for their object the economy of labor in working the same, or the increase of its capacity; when an entirely new principle is introduced, I no longer look upon this as evolution from the old type, but as the origination of an independent type of appliance. The box buddle was no doubt the predecessor of the old Cornish round buddle, which was evolved from it with the object of saving the labor required to work the box buddle; both machines are horizontal-current separators, in which the separation of sands of different densities is effected by their differential rates of fall in a horizontal current of water of considerable depth. These appliances, though well suited to sands, are for obvious reasons not adapted to the treatment of slimes. The revolving tables of the Harz and similar types, on the other hand, act on the principle which I have called separation in thin films of water, and which Mr. Simons calls the film sizing principle, in which the resistance of the surface over which the pulp flows plays an essential part in determining the separation of the particles, and which is well suited to the treatment of slimes. Unlike the last principle, it will not work in deep bodies of water and cannot be used where considerable depth of material accumulates in the appliance, as in the box buddle and round buddle. As I have shown in my book, The Dressing of Minerals, p. 326, these revolving tables are a development of the appliance known variously as the flat buddle, flat table, or frame, the last name, which is the old Cornish one, being the one that I personally prefer. These primitive appliances, as well as the continuous-acting round tables described by Mr. Simons (his Figs. 10 et seq.) all work on the principle of separation in thin films, and are all adapted for the treatment of slimes; his buddles and round tables (Figs. 1 to 9) do not work upon this principle, and should therefore be sharply differentiated from the former. The evolution in each case of the continuous acting, more or less automatic, circular appliance from the primitive, intermittent, hand-worked, rectangular appliance has proceeded upon strictly parallel lines. The question of the evolution of the respective types involves a point of some importance as regards the principles of ore dressing.

Jan 1, 1915

By C. S. Smith, L. H. Beck

KNOWLEDGE of the Cu-Zn constitution diagram was critically examined in 1944 by G. V. Ray-nor,1 who suggested the diagram reproduced in Fig. 1 as the best evaluation of available data. No pertinent work on the constitution has been published since that time, although a number of authors have discussed transformation kinetics and theory. Despite the large amount of work that has been done on the constitution of these industrially important and scientifically interesting alloys, minor uncertainties still exist. For example, it is still not possible to say definitely whether a two-phase region exists between the ordered and disordered forms of the 8 phase. A careful re-examination of the phase boundaries in this part of the diagram was therefore undertaken. Two methods were selected for the new investigation—quantitative metallography for the higher temperatures and precision lattice parameter measurement for lower temperatures. Because of the relatively narrow two-phase regions flanking the ß phase in these alloys, quantitative metallography is particularly suited for their examination, since the relative amounts of the two phases are very sensitive to their compositions. The method, however, is useless below about 350°C because of the inadequate resolution of the two constituents. Below 400°, however, the X-ray diffraction method is applicable, although it is of somewhat lower sensitivity in this system. The changes of composition that occur during quenching from above about 500°C entirely vitiate X-ray measurements at room temperature though they do not affect metallographic area measurements. The two methods overlap and supplement each other admirably. Both methods depend on the attainment of equilibrium composition of the two phases in a more or less intimate mixture and thus avoid the difficult problems of nucleation and long range diffusion involved in the conventional metallographic bracketing method. The alloys were melted from a master alloy made from re-electrolyzed cathode copper and Horsehead 99.99 pct Zn. Melting was done under a cover of either borax or charcoal and the alloys cast into a 7/8 in. sq graphite mold for the a-ß alloys or a 3/8 in. diam cylindrical graphite mold for the ß-? alloys. The a-ß alloys were rolled at 750°C to 5/8 in. sq; annealed for 24 hr at 800°C and quenched; then rolled and swaged at 200°C to 3/8 in. diam rods, annealed 24 hr at 200°C, quenched and cold rolled 2 pct reduction. This treatment was intended to obtain a small grain size and to produce many nuclei of the minor phase for growth on subsequent heat treatment. The unworkable ß-? alloys were given preliminary treatment by sealing in Vycor tubes in vacuum and annealing for 4 hr at 800°C followed by cooling in air. Samples of homogenized alloys were checked spectrographically for impurities, but the principal components were determined on samples subsequent to heat treatment. The impurities analyzed averaged approximately as follows: Ag, 0.0002 pct; Fe, 0.004; Si, 0.0008; Cd, 0.005; Mg, 0.0002; and Pb, 0.002. For metallography, samples of appropriate composition were cut into rods 5/8 in. long, sealed in pyrex tubes in vacuum and annealed for eight weeks at temperatures of 470°C and below, two weeks at 480°, 500°, and 600°C, and 4 hr at 700°C, followed by quenching in cold water. Temperatures were accurate to ±2°C. The cylinders were then machined to 8.7 mm diam and a slice weighing 1.5 g cut with a thin saw transversely from the center of each. This

Jan 1, 1953