Search Documents

By H. S. Greismer

Alabama washes a larger percentage of its total coal output than any state in the Union. For producing coking coal, three-compartment jigs are favored; mines providing, steam and commercial coal use single-compartment jigs exclusively. Chemists are as necessary to washing plants as recording gages are to power plants. Experiments in Alabama indicate that the sludge released by coal-washing plants can be deposited in streams and on agricultural lands without disastrous results. CAMPBELL, 1 in 1896 said: "The Birmingham district in Alabama has certain great advantages for there are few places in the world where fuel and ore are so near together, although, unfortunately, both are of inferior quality; the ore being low in iron and high in phosphorus and the coal giving a weak and impure coke." This statement could not have been, questioned in 1894, but by 1896 several Robinson-Ramsay washers had been put into operation and weak and impure coke was a thing of the past. The Warrior coal field of Alabama contains six seams that yield coking coal of excellent quality. In descending- order, they are Brookwood, Milldale, Pratt, America, Mary Lee, and Black Creek. In each of these, however, bands of rock and bone coal of varying thickness are stratified with the coal; and while some of these impurities can be separated from the coal by the miner, much of it must be loaded out with the coal: Consequently, unless the coal is washed before being coked, it will yield a coke of varying ash and sulfur content quite unsatisfactory, for blast-furnace use. At present, the Gulf States Steel Co. is producing run-of-mine coal at its Virginia mine, from the America seam, that is uniformly low enough in ash to permit of coking without washing, but this is the only exception to the above statement. Alabama was the first state to experiment seriously with coal washers, was the first to install washers on a large scale and, up to the present, has maintained the lead. The Alabama State Mine Inspector reports that during 1923 20,919,303 tons of bituminous coal were mined in Alabama; 12,858,499 tons of which were delivered to coal washers for treatment.

Jan 9, 1924

and would also contribute to the post-war employment. -As far as the future is concerned, I doubt whether any of the present geophysical methods will ever be developed to directly indicate ore. However, the geochemical methods and certain combinations between chemical and geological methods now used might be the answer to our prayers for direct and more definite methods of determining the quality of the ore or its relative metal content. Geochemical and spectrochemical analysis of minute content in ground waters, in soil or in plants and trees, living or dead, will be extremely important and I would venture to predict that in the very near future each mining or exploration company and each assay oflice will have its own spectroscope equipped for accurate chemical analysis, not only to guide the daily work in the mine, but also for identifying ores as well as for guiding exploration, geological mapping and the evaluation of geophysical indications. These methods, although they are still in their infancy, promise very much for the future. Radioactivity methods could also be helpful when sufficient facilities for radioactivity determination can be made available. They have already been used to a great extent in oil exploration and experiments have shomn great promise for ore exploration also. As for future surveys of large areas, the exploration for physical contrasts will be made from the air, using aeroplanes, helicopters, etc. Already electrical and magnetic methods have been designed whereby the instruments are carried in the aircraft and by automatic recording the location of anomalies is made in a simple enough manner. It should be possible in this way to cover, say, a square mile in an hour. Later Discussion Replies to Dr Lundberg. J. B. Macelwane.*—Someone has said that if a person knows his subject well enough he can explain it in words of one syllable. The point is well taken and I think the converse is also true. If a person cannot explain a subject clearly in simple words, it is either because he has not sufficient command of the language, or he is not master of his subject. Now it is obvious, it seems to me, that the remedy for both of these unfortunate conditions lies not in less education, but in more. If Dr. Lundberg has met geophysicists who confused and discouraged prospective clients by their inability to talk the language of the mine owner or of the mining engineer or geologist, the fault most probably lay in the geophysicist's lack of sufficient training; but it may also have been the want of ordinary common sense, which no amount of education can supply. It is hard to understand the position taken by Dr. Lundberg. Does he regret his own extensive training? noes he wish to say that he would have had greater success in geophysics if he had been only a mine hand with an instrument and a rule of thumb? As a matter of fact, I find it rather difficult to account for his presentation before this Committee on Geophysics of an emotionally distorted picture of the Report of the Committee on Geophysical Education, after the lapse of an entire year since the Report was read and discussed in its proper place, unless he honestly thinks he is handicapped by his knowledge and training and wishes to warn the whole profession against a similar fate. I regret that I am obliged to disagree so emphatically with Dr. Lundberg's thesis— but I believe it would be dangerous if left unchallenged, both because of the inaccurate statements it contains concerning the recommendations made in the Report and because of the ultimate discredit that would be bound to fall upon genuine geophysics if Dr. Lundberg's recommendations were extensively followed out. S. F. Kelly.*-—The argument that a science and its practitioners can be improved by debasing the standard of educational preparation is indeed a strange argument to come from the pen of a man with the education of Dr. Hans Lundberg. In criticising the Committee report, moreover, he has to a certain extent set up a straw man to belabor. The statement that the Committee report recommends that

Jan 1, 1946

and would also contribute to the post-war employment. -As far as the future is concerned, I doubt whether any of the present geophysical methods will ever be developed to directly indicate ore. However, the geochemical methods and certain combinations between chemical and geological methods now used might be the answer to our prayers for direct and more definite methods of determining the quality of the ore or its relative metal content. Geochemical and spectrochemical analysis of minute content in ground waters, in soil or in plants and trees, living or dead, will be extremely important and I would venture to predict that in the very near future each mining or exploration company and each assay oflice will have its own spectroscope equipped for accurate chemical analysis, not only to guide the daily work in the mine, but also for identifying ores as well as for guiding exploration, geological mapping and the evaluation of geophysical indications. These methods, although they are still in their infancy, promise very much for the future. Radioactivity methods could also be helpful when sufficient facilities for radioactivity determination can be made available. They have already been used to a great extent in oil exploration and experiments have shomn great promise for ore exploration also. As for future surveys of large areas, the exploration for physical contrasts will be made from the air, using aeroplanes, helicopters, etc. Already electrical and magnetic methods have been designed whereby the instruments are carried in the aircraft and by automatic recording the location of anomalies is made in a simple enough manner. It should be possible in this way to cover, say, a square mile in an hour. Later Discussion Replies to Dr Lundberg. J. B. Macelwane.*—Someone has said that if a person knows his subject well enough he can explain it in words of one syllable. The point is well taken and I think the converse is also true. If a person cannot explain a subject clearly in simple words, it is either because he has not sufficient command of the language, or he is not master of his subject. Now it is obvious, it seems to me, that the remedy for both of these unfortunate conditions lies not in less education, but in more. If Dr. Lundberg has met geophysicists who confused and discouraged prospective clients by their inability to talk the language of the mine owner or of the mining engineer or geologist, the fault most probably lay in the geophysicist's lack of sufficient training; but it may also have been the want of ordinary common sense, which no amount of education can supply. It is hard to understand the position taken by Dr. Lundberg. Does he regret his own extensive training? noes he wish to say that he would have had greater success in geophysics if he had been only a mine hand with an instrument and a rule of thumb? As a matter of fact, I find it rather difficult to account for his presentation before this Committee on Geophysics of an emotionally distorted picture of the Report of the Committee on Geophysical Education, after the lapse of an entire year since the Report was read and discussed in its proper place, unless he honestly thinks he is handicapped by his knowledge and training and wishes to warn the whole profession against a similar fate. I regret that I am obliged to disagree so emphatically with Dr. Lundberg's thesis— but I believe it would be dangerous if left unchallenged, both because of the inaccurate statements it contains concerning the recommendations made in the Report and because of the ultimate discredit that would be bound to fall upon genuine geophysics if Dr. Lundberg's recommendations were extensively followed out. S. F. Kelly.*-—The argument that a science and its practitioners can be improved by debasing the standard of educational preparation is indeed a strange argument to come from the pen of a man with the education of Dr. Hans Lundberg. In criticising the Committee report, moreover, he has to a certain extent set up a straw man to belabor. The statement that the Committee report recommends that

Jan 1, 1946

By Edgar C. Bain, William E. Griffiths

The results of an inquiry into the structural nature of some 70 iron alloys containing both nickel and chromium over a considerable range of concentration are briefly described in this paper. This study is a part of a comprehensive program of investigation into alloys involving chromium in progress at the Union Carbide and Carbon Research 1aboratories. All the compositions studied contained carbon in amount comparable to commercial alloys. The B Constituent In addition to locating the limits of composition for the three principal types of structure (polyhedral ferrite, martensite and austenite) and their combinations, certain other features of the system were observed. A hitherto undescribed brittle constituent (designated here as the "B constituent") was discovered. It is very hard, non-magnetic and forms in two modes from chrome-ferrite by recrystallization. It is the stable low-temperature condition for the equal-proportion chromium-iron materials containing less than 10 per cent. nickel. Although it partakes of the nature of an inter-metallic compound, yet it may exist over a considerable range of composition. It is non-existent above a temperalure zone, varying with composition, from 800° C. to 950° C., and heating above this critical temperature develops chrome ferrite persistent after average cooling rate; a few hours just below this temperature will develop the complicated brittle crystalline type. The B constituent, when found in the grain boundaries of alloys of lower chromium content, contributes a serious brittleness removable, however, by heating and cooling rapid enough to prevent its re-format'ion. By suitable means of precipitution, the hard B constituent can be made to strengthen the already stiff alloy matrix in the manner of submicro-scopic particles, as exemplified in duralumin or the Sykes iron-tungsten and iron-molybdenum alloys. A possible explanation is offered for the familiar brittleness developed in chrome iron at temperatures above about 475" C. and removable by

Jan 1, 1927

By J. Hudy

An investigation has been made to determine the applicability of the Cendrex X-ray instrument for the measurement of the ash contents of washed bituminous coal products. The results obtained for selected products from five preparation plants in the northern Appalachian region are described. Emphasis of the study was placed on low-ash bituminous coals suit-able for utility or metallurgical markets. There was good agreement between the results obtained by conventional ash determination methods and by the Cendrex for all the products tested. A principal disadvantage of coal in competition with other fuels has been its inconsistent quality, especially with respect to ash content. Mine rnechanization and production from coalbeds of inferior quality have accentuated this failing. Present quality control methods in coal preparation plants are inadequate because (1) control samples taken over a production shift only serve to give the average quality of the product, (2) conventional sampling and analysis data are usually not available at the time a shipment is scheduled, and (3) the plant operator does not have the use of such data when the coal is being processed so that operating conditions may be adjusted for correcting variations in quality. Thus, the development and use of continuous-control monitoring instruments is of prime importance. The Federal Bureau of Mines arranged to investigate an instrument using x-rays for rapid continuous ash determinations. Developed by the Dutch State Mines and first described in 1958,' this instrument, which has found widespread acceptance in Europe, is designed to provide ash analysis of any desired coal feed or product stream with only a five-minute time lag between sample collection and analytical results. With limit controls, this unit could be used to feed back signals to preset the separating gravity of coal washers, control the ratio of various coals needed to produce an acceptable blend, and permit the sorting of a washed product into two qualities, one which is below and the other which is above a prescribed ash content. This unit can also be used discontinuously for rapid determination of coal samples taken in the usual manner. THEORY Di jkstra and Sieswerda of the Dutch State Mines studied the effect of chemical composition and ash content on the absorption coefficient of coal with the transmitted radiation method.' They found that with an X-ray wavelength of 1.79 A and values calculated for the absorption coefficients of ash and combustibles, the absorption coefficient of coal gave a linear relationship when plotted against the ash content. Thus, a method of measuring the absorption coefficient of coal could also be used to measure the ash content. However, practical attempts to measure the ash content of coal by comparing the intensities of the transmitted X-rays failed. The absorption coefficient of coal can also be obtained by irradiating a layer of coal with x-rays and measuring the intensity of the diffused reflection (backscatter method). The relationship between the diffused reflection and the ash content is actually hyperbolic but approximates a straight line over a narrow range. A measuring circuit that balanced the difference in intensity of the reflected radiation from a standard surface against that from a coal sample was used. By plotting this difference of reflected radiation against the ash content, a curve which approximated a straight line over a range of 8 percentage points of ash was obtained. DESCRIPTION OF EQUIPMENT The apparatus performs two distinct functions: (1) the preparation of the sample to a suitable size consist and moisture content for delivery to the x-ray element, and (2) the measurement of the ash content by the x-ray element. In a continuous operation the coal sample is delivered to a conditioner where it is dried to a maximum of 1% surface moisture and pulverized in a high speed mill to -48-mesh. This material is fed, at a rate of 250-300 gpm onto a rotating disk, shown in Fig. 1, where it is mixed with material already present. The mixture is rotated on the disk and

Jan 1, 1969

By Albert B. Horn, J. J. McKetta, O. L. Culberson

Since water is present in natural gas and petroleum reservoirs, it is of engineering value to have accurate experimental data regarding the behavior of water in hydro-carbon systems. Since experimental data of this nature are so scarce in literature, a program is under way at the University of Texas to obtain experimental data regarding the distribution of water in petroleum hydrocarbons. This initial paper is subdivided into three parts: A. The apparatus and analytical procedure are discussed. B. The equipment has been checked by comparing the experimental data with data of literature on the solubility of methane in water at 77°F and pressures to 10,000 psia. C. Experimental data are presented at 100, 160, 220, 280, and 340°F on the solubility of ethane in water at pressures to 1200 psia. As the temperature is increased the solubility of ethane in water first exhibits a minimum and then a maximum solubility. The range of applicability of Henry's Law is discussed. INTRODUCTION Although considerable experimental data have been published on water-hydrocarbon systems in the hydrate region, the information on these systems in the vapor-liquid and the vapor-liquid- 'References are given at end of paper. Manuscript received at the office of the Petroleum Branch August 31. 1949. liquid regions at elevated pressures is extremely scarce. A survey of the literature on hydrocarbon-water systems at elevated pressures was presented by McKetta and Katz12,13,14 showing the systems and phases investigated. In addition to these existing published data, Poettman and Dean" have reported the water content of propane in the three-phase region (only the propane-rich liquid and the vapor phases were studied) and Michels, et al.15 have reported the solubility of methane in water at pressures to 6800 pounds per square inch at 77°F and at pressures to 1500 psia at temperatures to 300°F. It has been shown12,14 that the presence of water will materially affect the phase equilibrium of hydrocarbon systems. In order to make experimental studies on the quantitative effect of the presence of water in naturally-occurring hydrocarbon systems, it is desirable to have data available on binary hydrocarbon-water systems. A program is underway at this laboratory to determine the phase relations of the hydrocarbon-water systems. Initially the investigation will be limited to binary systems with water as one of the components. Later ternary and complex systems will be investigated and reported. EQUIPMENT AND ANALYTICAL PROCEDURE Apparatus In order to avoid a description of the methods employed in each subsequent paper, a description of the apparatus and the analytical procedure will be given here. The apparatus is shown schematically in Fig. 1. The numbered items in Fig. 1 represent the high pressure valves. The equilibrium cell is of the totally enclosed type, with a volume of 550 cubic centimeters. The cell is mounted in an air bath which in turn is mounted on pillow blocks and connected to a rocking mechanism so that the cell and bath will oscillate approximately 30 degrees above and below the horizontal at 35 oscillations per minute. The air bath is heated by two resistance heaters. The first or primary heater is 250 watts and is controlled by a thermoregulator; the second heater is of 500-watt size and is manually controlled to aid in bringing the cell to equilibrium temperature. Air circulation in the bath is accomplished by means of a fan. the shaft of which is concentric to the heaters. The walls of the bath are insulated with 2-in. thick blocks of 85 per cent magnesia. Temperature observations are made with three calibrated thermocouples. One couple is sealed in a well provided within the equilibrium cell, and is used as the criterion of the cell being at the equilibrium temperature. The other two thermocouples are located on opposite sides of the cell to indicate temperature uniformity within the air bath. The thermoregulator, used in conjunction with a relay, gives a variation in the temperature of the air in the bath of plus or minus one degree Fahrenheit. However, since the equilibrium cell weighs approximately 55 pounds, the

Jan 1, 1950

By R. V. Higgins, A. J. Leighton

Interest by petroleum engineers in the flow of three phases—oil, gas and water—in irregularly bounded porous media lies mostly in the performance calculation of water floods of reservoirs that have been partially depleted as the result of expansion of much of the originally dissolved gas. The authors present a method to forecast three-phase flow in complex geometry and explain the details by the use of a specific example of a five-spot water flood of a partially depleted stratified reservoir. In this example, the fluid and rock properties of a field given by Prats, et al,' were used. The computed results fit the field performance more accurately than Prats, et al, and Slider.' The time required for the high-speed digital computer to make the calculations, including the contributions from the different layered zones, is about one minute. INTRODUCTION The declining rate of discoveries of new oil fields in the United States makes the recovery of more oil from known reservoirs more attractive than previously. Water flooding has an excellent proved background for recovering additional oil economically. Accordingly, the main interest of this paper is in this type of recovery. In petroleum engineering studies, commercial interest in three-phase flow is mostly in the water flooding of reservoirs in which the oil has been partially produced by the expansion of dissolved gas. When water is pumped into these reservoirs, three-phase flow takes place. Although this paper is concerned with these conditions, the principles involved could be used for other conditions when and where they come to the fore. Many investigators have made contributions to non-empirical forecast methods using basic scientific engineering principles. Several of these used the oil in place at the start of the water flood and the oil remaining after a large quantity of water has passed through a core for key values in their calculations. Recently, Prats, et al,' and Slider have reduced assumptions by adding the third phase—gas—in their forecasting methods. Slider uses the mobilities in the immediate vicinity of inlet and outlet wells as an aid to simulate the resistance effect in the five-spat pattern of the flow of oil, gas and water. Prats, et al. minimize assumptions by using previously determined laboratory data for determining sweep efficiency in the five-spot pattern. In neither of these papers is the saturation profile continuously affected by permeability-saturation curves. Sheldon and Dougherty- recently described a method that employs continuously changing saturation profiles using permeability curves, has a minimum of assumptions and needs no prior sweep efficiency. The Higgins-Leighton method, described in this paper, has all of these features; however, many of the techniques are different from those of Sheldon and Dougherty. The Higgins-Leighton method, tested in May, 1961, is direct and easy to apply and requires very little computer time to calculate a forecast. The short computer time is especially helpful in the study of a reservoir containing many layers of different relative permeabilities. In the Higgins-Leighton method, the individual pressures do not have to be calculated, as the resistance to flow in each cell in the flow pattern is readily determined without the use of any iterative techniques. The saturation and permeability distributions are readily determined. These data and the shape factor, which is measured only once from the potentiometric model when mobility ratio is one, determine the resistance to flow in each cell. THEORY The authors showed in a previous paper4 that, as an aid to calculating performance, the reservoir can be divided into channels using the streamlines of a potentiometric model as a guide. See Fig. 1. This procedure also was used in this paper. The authors also showed that, by treating conduits as approximately one-dimensional and neglecting pressure gradients transverse to the main flow, the Buckley-Leverett equation may be expressed as The principles expressed by this equation are employed extensively in the three-phase flow, as they were in two-phase flow. In the three-phase flow, the channels (the size and shape of which are taken from a potentiometric model)

By J. Moore Samuel

Before the year 1909, no measurements of dust losses and flue gases had been made at the Copper Queen Reduction Works, at Douglas, Ariz. At that time the "unaccounted" loss of the smelter had reached a figure that drew attention to the possibility of large stack losses. The measurement of dust losses had not been studied much at that time, and estimates of dust losses, with a few exceptions, were the results of tests by what has been termed '(chemical methods," that is, the aspiration and filtration through cotton, wool or some similar medium of a few liters of gas, the dust being weighed on a chemical balance, and the volume of gas computed from the volume of aspirator water. The possible error of this method is enormous, and the probable error much too large for reliable results. Since the object of these tests was to discover not only the extent of the dust losses, but also the possibility of profitably reducing them, it was decided that the method adopted must have the following characteristics: 1. The sample of gas taken for filtration must be representative of the whole volume of gas, that is to say, it must have the same dust content. This condition will be fulfilled in all cases if the gas sample is drawn off without change of rate of flow. Then it will contain the same proportion of entrained or suspended particles of dust as the original gas. In the case of flue gases which contain only fume, at a temperature above or near the sublimation point, this condition need not be adhered to since the fume will not behave as entrained particles, but more nearly as a true gas. Consequently the gas sample in this case only may be drawn off at any rate of flow. 2. The gas sample taken must be large enough (a) to yield sufficient dust to permit of accurate chemical and physical examination; (b) so that the ratio of the total volume of gas passing through the flue to the volume of gas sample taken shall not be too large.

Jan 1, 1917

By A. N. Winsor

Increased use of private aircraft in civil engineering, mining, forestry, and other land-use activities creates an opportunity for amateur aerial photography. Taking a photograph having less than 5° tilt requires precision equipment and skilled personnel, while controlled horizontal photography is primarily a terrestrial method that has passed to the limbo of forgotten things. But the remaining possibility – oblique aerial photography – can be…

Jan 2, 1955

By Douglas A. Blankenship, Randall G. Stickney

The corejacking test is a field test designed to measure the response of salt to known boundary conditions. A 1.0-m-diameter salt core is externally pressurized using curved flatjacks placed in the annulus surrounding the core. Time-dependent deformation of the salt is measured by monitoring the diametrical closure of an inner borehole. A finite element elastic analysis of the jack loading system has been performed. The purpose of this analysis was to determine if the original assumption of axisymmetric loading is correct. Six loading cases were investigated, each representing either hypothetical or previously encountered jack configurations.

Jan 1, 1982

By G. Horvay, J. G. Henzel

Nomograms and charts are provided which permit rapid determination of the mold-casting interFace temperature and the speed of solidification when a semiinfinite ingot is cast into a semiinfinite mold. The physical properties of the mold, the frozen metal, and the liquid metal are not assumed to be equal, but they are assumed to be temperature independent. The results are correlated with charts prepared by Paschkis and Hlinka—using Columbia University's Analog Computer—for the freezing of finite ingot slabs when a constant surface temperature is impressed, and with experimental cooling curves obtained by Pellini in sand and iron molds for 7 in.-sq steel castings. x = coordinate directed to right of zero (freezing direction) y = coordinate directed to left of zero (melting direction) e = position of freezing front (in x direction) ? = position of melting front (in y direction) $ = temperature (function of position and time) ? = fixed temperature 2L = width of finite slab Y = a fixed position in the semiinfinite mold, or the width of a finite mold (see Section 7) Properties y = density, lb per cu ft c = specific heat, Btu per lb deg F k = conductivity, Btu per ft hr deg F X = heat of fusion, Btu per lb k = k/Yc = temperature diffusivity, sq ft per hr* b - = = - heat diffusivity, Btu per sq ft deg F Vhr Subscripts 2 = pertaining to the still-liquid metal (case of freezing), or the medium which furnishes the heat (case of melting) 1 = pertaining to solidified metal (case of freezing), or to molten metal (case of melting)* 0 = pertaining to mold (case of freezing), or to the still-solid metal (case of melting) f = pertaining to fusion condition (eg.,?f - fusion temperature) i = pertaining to the location x = 0 (the mold-ingot "interface")

Jan 1, 1960

By I. C. Runge

This paper outlines in a step-by-step approach all of the major tasks to be undertaken for the design of a complex multi-seam open pit coal mine. Examples are drawn from three such projects in the Hunter Valley of New South Wales, Australia, where computer techniques for equipment production rate estimation, mining block layout, and mine scheduling were used extensively. The paper is divided into two sections - Conceptual Planning and Detailed Planning; and the various tasks associated with these sections are discussed in detail, with examples of typical problems to be overcome.

Jan 1, 1983

By H. B. Pulsifer

One of the most common basic open-hearth furnace products is a simple carbon steel with a carbon range from 0.05 to 0.15 per cent. The material is widely used for sheets, tubes, bars, wire and the innumerable special objects of secondary fabrication. The properties of the material vary over wide ranges, depending on the more exact composition and details of manufacture or treatment that affect its structure. The present paper is a review of those properties and structures that have been found by studying this steel as used in the cap screw industry. At first glance this might be thought a narrow application of the steel, but, since the industry uses the material in the cold-worked, annealed and heat-treated conditions, the title of the paper may be excused for its comprehensiveness. Yet, in studying the wide ranges of properties and structures that preclude a more specific title, there can be no suggestion of completeness or finality. Even a summary of a few years' work is no more than a preliminary survey of a field that will be fertile in scientific data and industrial products for many years to come. An outline of the structures will be given first, then a list of the previous contributions that are at hand and finally some details of the work and related problems, especially concerning this low-carbon steel in the surface-hardened condition. Wire Used in Manufacture of Cap Screws The wire that is used for making cold-upset and roll-threaded cap screws has been cold-drawn from hot-rolled rods that were pickled and limed. The common sizes used in the industry range from 0.185 to 0.750 in. dia., the exact diameters depending on the plant practice and having the usual tolerances of 0.002 in. for the smaller sizes and 0.003 in. for the larger sizes. The carbon range, by pit analysis, is usually between 0.07 and 0.12 per cent. Manganese should be within the usual 0.30 to 0.50 per cent. range. Sulfur rarely exceeds 0.045 per cent. and phosphorus seldom exceeds 0.030 per cent. Silicon is usually below 0.03 per cent. but in the silicon-killed steels may be in the customary 0.10 to 0.25 per cent. range. Rimmed steel is not considered most suitable for cap screws that are cold-headed or for parts that are to be surface-hardened.

Jan 1, 1931

By A. E. Worthington, R. F. Meldau

An analog computer study was made of the reduction of the magnitude of the SP by formation geometry and resistivity effects. Practical field .situations were studied. The analog data were converted to the form of departure charts. These charts may he used to determine the reduction in the SP due to the above eflects pith good precision Quantitative interpretation of the SP log in terms of formation water resistivity is presently based on the premise that the observed SP is equal to the electrochemical potential developed across a shale between the mud filtrate and the formation water. This procedure inherently assumes that, first, no electro kinetic (streaming) potential is present, and, second, that the SP is not reduced by resistivity or geometry effects in the formation. When, however, such a reduction of the observed SP does occur, one may write, SP = b,E, b, E, (1) where SP is the observed self-potential opposite the center of the bed under consideration. In this case, E, is the electrochemical potential, E, is the electrokinetic potential, b, is the electrochemical reduction factor, and h, is the electrokinetic reduction factor. The first assumption above is equivalent to assuming E, = O in Eq. 1 and the second assumption is equivalent to h, = b, = 1. Examination of electric logs shows that for many formations of interest the observed SP is reduced below its maximum value. The object of this work is to aid quantitative SP interpretation in at least some of these situations by obtaining values for b, and b, in Eq. 1 as functions of realistic combinations of bed thickness, depth of invasion, and formation resistivity. The only previously published work in this field known to the authors is by H. G. Doll' in 1948. He evaluated b, under conditions permitting exact analytical solution. His work clearly established the importance and qualitative nature of formation geometry and resistivity effects upon the SP, but the necessity of obtaining analytical solutions restricted his study to situations of limited practical interest. In order to extend such studies to practical combinations of formation parameters which do not lend themselves to feasible analytical solutions, the results reported in this paper were obtained by use of a special analog computer. THE ANALOG MODEL The analog model used for this study was the Guyed Analog Computer which originally was designed and built for resistivity log departure curve studies. It consists of a two-dimensional mesh of resistors, with the vertical mesh corresponding linearly to vertical distance along the borehole, and the horizontal mesh corresponding to radial distance from the borehole axis. By proper choice of horizontal resistor values, a three-dimensional, axially symmetric, borehole-formation problem can be modeled with this two-dimensional array. These and other details of the model are contained in a paper by H. Guyod'. The geometry used for the SP studies with the analog is depicted in Fig. 1. This configuration has a horizontal plane of symmetry, and, hence, the model, and the following discussion, need only to be concerned with one quadrant such as shown in Fig. 2. A further simplification arises by considering that both the natural potential sources and those used in the model have fixed internal impedance. Therefore, the current flows produced by these sources can be separated and studied independently ( i.e., the superposition theorem can be applied). SP = SP, i SP, = h,E, + b,E, ,(7)

By F. Selig, A. S. Odeh

A second-order approximation to the exact solution of the diffusivity equation corresponding to the pressure build-up of a well producing at a variable rate is derived. This approximation is applicable when the well's shut-in time is larger than the total time elapsed since the well was first produced. The resulting equations are compact in form and easy to use. Thus, the need for Horner's' theoretically precise but rather laborious solution to the above problem is eliminated. In addition, these equations apply where the use of Horner's widely known approximate method is questionable. From a practical point of view, the reported method is best suited for analysis of drill-stem tests and short production tests conducted on new wells. INTRODUCTION The utility of drill-stem and short production tests in reservoir studies has long been recognized by the reservoir engineer. If interpreted correctly they could lead to a wealth of information upon which may depend the success or failure of reservoirs' analyses. Initial reservoir pressure and the average flow capacity are two quantities that are normally sought from a drill-stem and/or a short production test analysis. Pressures are the most valuable and useful data in reservoir engineering. Directly or indirectly, they enter into all phases of reservoir engineering calculations. Therefore, their accurate determination is of utmost importance. The flow capacity kh of the reservoir is indicative of its commercial capability. In addition, it can indicate the presence of a darnaged zone around the wellbore and, thus, the necessity for remedial measures. Of the several methods used to analyze drill-stem and short production tests, Horner's' method is by and large the most common. It applies to an infinite reservoir and or a limited reservoir where the effect of production has not been felt by the boundary. Horner's method makes use of the so-called "point-source" solution of the diffusivity equation. The point-source solution is approximated by a logarithmic function and the superposition theorem is utilized to give the familiar pressure build-up equation where is the shut-in time, q is in reservoir barrels per day and the rest of the symbols conform with AIME nomenclature. Eq. 1 was derived for a well which produced at a constant rate q from time zero to time t and was then shut in. In actuality, such a constant rate of production does not normally obtain. Therefore, a correction must be applied to Eq. 1 to account for the varying rates of production. Horner suggested two methods. The first, which results in a theoretically accurate solution, is rather lengthy and laborious and, thus, it is not suited for routine analysis. The second which has been termed a "good working approximation" is the one used by the majority of the reservoir engineers. In the second method, Eq. 1 is modified by simply introducing a corrected time t, and writing where q is the last established production rate prior to shut-in, and t, is obtained by dividing the total cumulative production by the last established rate. Horner's original paper does not give any indication that this method of correction is based on any theoretical justification. In addition, there is a question as to what constitutes the last established rate. In case of a drill-stem test some engineers use the average rate obtained by dividing the total fluid produced by the total flow time, while others calculate the average rate by dividing the total fluid produced by the last flow-period time. Obviously, different results obtain for the different flow rates used. Because of this, a simple method to the varying-rate case was developed which is theoretically sound and which defines clearly the flow rate and its associated time to be used in the calculations. The final equation arrived at is where q* and t* are a modified rate and time, respectively, and can be easily calculated. In addition, it is shown theoretically that Horner's approximate method, if used for a variable-rate case, gives the correct pressure but would not be expected to give the correct flow capacity. MATHEMATICAL ANALYSIS The general equation governing the flow of slightly compressible fluid in porous media may be written as The elementary solution to Eq. 4, representing an instantaneous withdrawal of Q units volume of fluid at the origin at t = 0, is known as the instantaneous sink

By Charles Catlett

THE rapid development of the Portland-cement industry implies that the country is being very carefully searched for material suitable for its manufacture. Such material can be found at a great many places ; but deposits thoroughly satisfactory in chemical composition, and at the same time meeting all the other requirements connected with the economic production and profitable marketing of the product, are exceedingly few, if I may judge from the investigations which I have had to make in a number of States. The raw mixture which by its clinking and grinding forms Portland cement contains approximately 75 per cent. of carbonate of lime. This is found in nature as limestone or marl. The natural rock commonly carries either more than the required percentage of carbonate of lime (in which case it has to be reduced by suitable admixture of clayey ingredients) or less-in which case purer lime carbonate has to be added. The controlling ingredient, therefore, is carbonate of lime, or limestone of the right composition. Among the most serious difficulties is that of finding limestones low enough in magnesia to meet the exacting requirements of certain specifications. All engineers recognize that there is a limit beyond which it is not safe to let the magnesia go; but within that limit there is considerable difference of opinion. Until that difference is finally settled, no one would be willing to invest the large sum of money necessary for a Portland-cement plant, if it were not certain that the usual requirements in this particular could be satisfied. The usual limit in well-established specifications is 5 per cent. of magnesium oxide in the finished cement, but many specifications limit the amount to 3 per cent. These figures

Jan 9, 1907

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

By E. J. Roberts

The theory is developed that the tons ground through a given mesh per day in a wet ball mill is proportional to the percent plus that mesh in contact with the balls and the net power applied to the balls at this point. A grindability test is described. DURING the course of a study of the fundamentals of classification in 1937, the need for a more basic understanding of the action of a ball mill became acute. Unless one knows how classification affects grinding, one cannot hope to effectively improve on classification. The methods of evaluating grinding efficiency that depend on surface developed were studied but soon discarded for two reasons: 1. There was no apparent method which could be generally used to give a reliable figure for the actual new surface developed as a result of grinding. Subsequent papers have not changed this conclusion. 2. The practical evaluation of grinding in the main ore dressing applications was in terms of the percentage retained on a screen which passes 90 to 99 pct of the material and not in terms of surface area. The Probability Theory With the background of our experience in the field of closed-circuit grinding, together with the papers of Lennox,1 Gow,2 Gaudin,8 Fahrenwald,4 Coghill, and others, the approach of the theoretical physicist was then tried. The thought was somewhat as follows: When one grinds in a ball mill, a given expenditure of power leads either to a certain number of point to point blows per hp-hr or to a certain distance of line contact per hp-hr, depending on whether the action of the balls is considered to be cascading or rolling. It is also assumed that the balls actually come together on each blow or during the roll. Then a volume of slurry will be covered per minute which is some function of the size of the particle being considered (see fig. 1). All particles coarser than this size will be reduced through this size. This volume of slurry contains a certain weight of ore, depending on the percent solids and the density of the solids. If we fix the percent solids and the density of the solids and let w be this certain weight of ore in the volume covered, then, in mathematical terms, what we have just postulated is, w —— 8 hp (a) dt If W is the total weight of ore present in the mill, then we can write. W w/8 hp (b) W dt and if C is the cumulative percent plus the size chosen at the start of the time interval dt, w w c/dt W 8 hp x c (c) wc But wc/100 is the weight plus the size chosen which at 100 wc the close of time dt is finer than that size, and W is the decrease in the percent plus of the whole mass of ore or —dC. Then, —W dC/dt 8 hp x C. (d) In other words, the mesh tons ground through a given size per unit of time is proportional to the hp and the percent plus the mesh. A crude analogy would be to picture a 1-ft-wide steam roller going down the road at 1 ft per sec. If we place one egg on the road per square foot, one egg will be smashed per second. If we place a dozen eggs per square foot, a dozen eggs will be crushed per second. Similarly, if all the particles in w are plus the mesh, i.e., C=100, we should have a maximum rate of reduction. If only 10 pct of them are plus the mesh (C=10), we would have only one tenth the maximum rate; if only 1 pct are plus the mesh, the balls have a hard time finding anything to work on. This is where the term "probability theory" comes from. The chances of the balls crushing a particle through a given mesh depends directly on the concentration of particles coarser than this mesh in the general pulp in the mill. Giving W the units of tons and dividing equation (d) through by W, we obtain -dC hp ----- = k---— C [1] dt ton where k is a constant for any one size of particle, density of solid and moisture content of pulp. Eq 1 is the rate equation for a first order reaction and says that the rate of decrease of the percent plus a given mesh with time is directly proportional to the hp per ton applied to the body of ore and to the percent plus the mesh in the ore mass as a whole. Since it is a differential equation, it only

Jan 1, 1951

By Benny J. Nelson

AS a part of the fundamental research program of Aluminum Research Laboratories, some data were obtained on the ternary system Mg-Al-Mn. As very little information on the magnesium corner of this diagram has heretofore been published, it seems desirable to make available the values found for the liquidus and solidus surfaces of this system. Procedure The settling procedure was used for the determination of the liquidus compositions. Metallo-graphic examination of quenched samples, and stress-rupture upon incipient melting, were used for the solidus determinations. The settling procedure has been described in a previous paper.' Briefly, this method involved saturating the alloy with manganese at a temperature substantially above that at which the sohbility was to be determined, then cooling the melt to the latter temperature, and holding it at that temperature for a substantial period of time. Samples for analysis .were carefully ladled from the upper portion of the melt at hourly intervals during the holding period. After the ladling of each sample, the melt was stirred to redistribute some of the manganese that had already settled, because it appeared that when the latter particles of manganese again settled, they aided in carrying down more of the manganese and thus hastened the attainment of equilibrium. The melts were prepared and held in a No. 8 Tercod crucible holding approximately 4 lb of metal. The manganese was added either in the form of a prealloyed ingot (Dow M) containing about 1.5 pct Mn or by the use of a flux (Dow 250) containing manganese chloride. In calculating the flux additions, it was assumed that the manganese introduced would be equal to 22 pct of the total weight of the flux. Temperatures were measured with an iron-constantan thermocouple enclosed in a seamless steel tube, the lower end of which was welded shut. This protection tube also served as a stirring rod. The samples ladled from the upper portions of the melts at the various intervals were analyzed for aluminum, manganese, and iron. When making the alloys which were to be used for the determination of the solidus, 2½ in. diam tilt mold ingots were cast, scalped to 2.0 in. in diam, and extruded into ? in. diam wire. The principal impurities in the melts for this investigation were iron and silicon; their total not exceeding 0.03 pct. Portions of the wire, approximately 2 in. in length, were enclosed in stainless steel capsules for protection from the atmosphere. Bundles of these capsules, with a dummy capsule containing an iron-constantan thermocouple, were heated inside a large steel block (acting as a heat reservoir) in a closed circulating-air type electric furnace. At ap- propriate times, the capsules were removed and quenched in water. The wires were examined metallographically to determine the temperature of initial melting. Short times at temperature were used at the beginning for wire specimens of all alloys to obtain quickly the approximate temperatures at which melting could be first observed. When approximate solidus temperatures had thus been determined, equilibrium heating was attempted. This equilibrium heating consisted of an 8 or 16 hr period at a temperature, about 50 °F below the lowest temperature at which melting occurred when short heating cycles were used, followed by further heating for 1 hr periods at consecutive 10" higher temperatures. The theory for the method of stress-rupture at incipient melting has been well covereda and its limitations are recognized. Thus, if the interfacial tensions are such that the first minute quantity of liquid is "bunched up" at the grain boundary junctions instead of spreading out along the grain boundaries,³ temperatures higher than the solidus are required before melting will be manifested by rupture of the specimen. This point will be elaborated later. Specimens of the wires with a reduced section (approximately 1/16 in. diam) were suspended vertically in a tubular furnace. The setup used is shown in Fig. 1. The clamp holding the specimen was made from alumel thermocouple wire and the thermocouple was thus completed across the specimen by attaching a chrome1 wire to its lower end. Temperatures were read from a Speedomax recorder used in conjunction with a calibrated thermocouple. The small weight attached to the specimen and a vibrator attached to the furnace tube, to aid in distributing the molten constituent along the grain boundaries, were used to bring about rupture at a temperature closely approximating the solidus. The specimens were heated at a rate of about 5°C per min. The rupture of the specimens was indicated both by sound and by the action of the recorder. An argon atmosphere containing a small amount of SO² was used for protection of the specimen. The assembly was taken out of the furnace immediately following rupture and the specimen removed. Some of the broken specimens were examined metallographically and will be referred to later. Results and Discussion Fig. 2 shows a set of typical time-composition curves for liquid samples of the Mg-Al-Mn alloys used for the settling tests. The data as presented

Jan 1, 1952

By R. W. Heckel, R. E. Trabocco

The recovery process in 400 Monel filings was followed, principally, by using the Warren-Averbach technique of X-ray peak profile analysis. The deformation fault probability, a, was 0.006 in samples of unannealed filings. a , the twin fault Probability , was approximately 0.002 in samples of unannealed filings. Both a and 0 were found to "anneal out" at 600°F. The effective particle size and mzs strain increased and decreased in the (111) direction, respectively, with increasing annealing temperature. The actual particle size was found to be almost equivalent to the effective particle size. Tile small values of deformation and twin fault probabilities accounted for the similarity in values of the effective and actual particle sizes. Stored strain energy and dislocation density calculations based on rms strain decreased with increasing annealing temperature. The dislocation density decreased from 10" per sq cm in the unannealed filings to 10' per sq cm in the partially re-crystallized filings. The square root of the dislocation density based on strain to that based on particle size indicated a random dislocation distribution in the unannealed filings. The dislocation arrangement changed to one with dislocations in cell walls with increasing annealing temperature. THE recovery processes which occur in metals are generally thought to be a redistribution and/or annihilation of defects.' Investigators' have shown that recovery processes can be characterized by X-ray line-broadening analyses. Michell and Haig4 measured the stored energy of nickel powder by calori-metry and found the value to be greater by a factor of 2.5 than that from X-ray data obtained by the Warren-Averbach technique.= Minor increases in particle size occurred up to 752°F (recovery), while above 752°F the particle size increased greatly due to recrystalliza-tion. X-ray microstrain values decreased between room temperature and 392"F, remained constant from 392" to 752"F, and decreased from 752°F to a negligible value at 1112°F. Faulkner developed an equation for calculating stored strain energy based on X-ray line-broadening data which gave a closer correlation of measured and calculated stored strain energy based on the data of Michell and Haig. The stored strain energy released during recovery is predominately dependent on the decrease in dislocation density which was p-enerated from cold work.7 Stored energy has been measured8 in alkali halides during recovery and recrystallization and 80 pct of the stored energy was found to be released during recovery. Dislocation distributions have been studiedg in a number of fcc metals by thin-film electron microscopy. Howie and Swann" found the stacking fault energy of copper and nickel to be 40 and 150 ergs per sq cm, respectively. ~rown" has pointed out that these stacking fault energy values should be corrected to 92 and 345 ergs per sq cm, respectively. The dislocation distribution of a metal is directly dependent on the stacking fault energy of the system. Metals of high stacking fault energy such as aluminum cross-slip readily and do not form planar arrays of dislocations. Metals of lower stacking fault energy such as stainless steels" do not cross-slip readily. Cold-worked nickel has been found to form a cellular dislocation structure after annealing.13 The relatively high stacking fault energy of nickel and copperlo to a lesser extent favor cellular structures of dislocations rather than planar arrays after deformation. The present study of recovery was carried out on a Ni-Cu alloy (Monel 400) to compare with prior studies for pure nickel and pure copper. X-ray line-broadening techniques were used to measure the effect of recovery temperature on rms strain and particle size and the results were compared with previous studies on copper'4-'7 and nickel., Calculations were also made on stacking fault probabilities, dislocation density, dislocation distribution, and stored strain energy as affected by temperature. EXPERIMENTAL PROCEDURE The nominal analysis of the Monel 400 used in this investigation was: 66.0 pct Ni, 31.5 pct Cu, 0.12 pct C, 0.90 pct Mn, 1.35 pct Fe, 0.005 pct S, 0.15 pct Si. The annealed material was cold-reduced in two batches, one 50 pct and the other 80 pct. It was originally planned to conduct line-broadening studies of these bulk samples; however, rolling textures that developed produced low-intensity peaks which were not suitable for line-broadening analysis. Filings were prepared at room temperature from both the 50 and 80 pct cold-reduced specimens, series A and series B, respectively, and were not screened prior to heat treatment or X-ray studies. Heating to the annealing temperature, 200" to 120O°F, was accomplished in a matter of minutes in a hydrogen atmosphere. Following heat treatment, some of the filings were mounted and polished for microhardness measurements with a Bergsman microhardness tester, using a 10-g load. A G.E. XRD-5 diffractometer using nickel-filtered Cum radiation was used to obtain all diffraction patterns. Only (111)- (222) line-broadenin data were used in the present study since the {400f peaks were too weak to use. The Fourier analysis of the (111) and (222) peak

Jan 1, 1969