Search Documents

By Walter Harvey Weed

CONTENTS. [ ] INTRODUCTION. THIS paper deals with certain ore-deposits whose structural features or mineral contents (or both) result, directly or indirectly, from igneous intrusions and their after-effects. It is largely a discussion of contact metamorphic ore-deposits based upon the physical changes in rocks due to contact action. It involves a classification of ore-deposits only so far as is abso-

Jan 1, 1913

By C. W. Crispell

THE four nomograms presented in this article were designed to simplify and make more, rapid the calculations connected with the compression and transmission of air. The formulae involved are rather complicated, but the graphic solutions are simple; their use requires an ability to follow explicit directions and to interpolate values on a logarithmic scale. ? For the sake of convenience, the nomograms will be divided into two classes, and the purpose and accuracy of each will be discussed. Compression It is frequently desirable to determine the horsepower necessary to compress a given amount of free air from atmospheric pressure to a certain final pressure. The nomograms in Figs. 1 and 2 present a rapid method of calculating the horsepower required to compress 1 cu. ft. of free air per minute by single or two-stage compression. The general formula for the horsepower required to compress air adiabatically is: HP = S X 144/33,000 PVn/(n-1) [(P'/P) n-1/Sn -1] (1) where: P = absolute atmospheric pressure at compressor, in pounds per square inch. P' = final absolute pressure of compressed air, in pounds per square inch. V = volume of free air compressed per minute, in cubic feet. S = number of stages. n = exponent of the compression curve.

Jan 6, 1917

By T. B. Counselman, T. B.

Continuous countercurrent decantation calculations have always been a headache to the cyanide man (and the chemical engineer) because of the simultaneous equations involved. These are tedious to solve, and there is considerable opportunity for mathematical error. This paper presents a shortcut method for making these calculations, which has been in successful use for twenty years by the author, and which is particularly valuable in selecting the best of several possible flowsheets, or evaluating the effect of various assumptions.

Jan 1, 1950

By J. Hunter

LouisiaNa ranks fifth among the oil-producing states. In 1941 the state-wide production was slightly in excess of 118,000,000 bbl. of crude oil and conden-sate—an increase of 15,000,000 bbl. over the total production for the year 1940. During 1941, south Louisiana produced approximately 90,900,000 bbl. of oil, while north Louisiana produced approximately 27,000,000. South Louisiana, therefore, produced about 3¼ times more oil than north Louisiana. During the past year, 574,800,000 M cu. ft. of natural and casinghead gas were produced in Louisiana; thus 1941 gas production exceeded the 1940 production by 104,900,000 M cu. feet. Completion records for the year 1941 show that 1512 wells were completed in or adjoining producing fields. These wells, which were drilled to extend known producing areas or were located within producing areas, are not considered as wildcat wells. Of the total number of field wells drilled, 1152 wells found production; the remaining 360 were junked or dry and abandoned. This means that 76 per cent of the wells drilled were successful. Considering the precarious nature of oil-field development, this percentage of new producing wells is exceedingly satisfactory. Of the total number of field welis com-pleted as producers, approximately 86 wells found new and distinct producing sands. During the past year, 30 new fields were found. Four parishes—namely, Caldwell, Catahoula, Orleans, and Natchitoches— entered the ranks of oil-and-gas-producing parishes in the state during that period. This brings the total number of oil-and-gas-producing parishes in the state up to 48. Thus, 75 per cent of the parishes in Louisiana now contain one or more oil and/or gas fields. Although sufficient data are not available to list the addition reserves found in Louisiana during 1941, it is felt that such reserves undoubtedly exceed twice the total production for that year, or at least 200 million barrels. In reserves, therefore, Louisiana ranks third among the various oil-producing states. South Louisiana Although 16 new fields were found in south Louisiana, the outstanding developments in that part of the state were not limited to new discoveries. In fact, most of the increase in reserve in that area has been most consistently accumulated through extensions of known producing sands and through the finding of new sands in already productive fields, especially at depths below the presently producing sands. Since data concerning most of the new extensions and sands are too extensive for discussion here, the more important developments arc briefly outlined below: Abbeville, Vermilion Parish.—Production extended ½ mile to the west. Anse La Butte, St. Martin Parish.—New oil sand discovered at 9400 ft., thus extending production to east flank. West flank defined by dry holes. Barataria, Jefferson Parish.—New oil sand discovered on east side of field at 7620 ft. New

Jan 1, 1942

By J. Hunter

LouisiaNa ranks fifth among the oil-producing states. In 1941 the state-wide production was slightly in excess of 118,000,000 bbl. of crude oil and conden-sate—an increase of 15,000,000 bbl. over the total production for the year 1940. During 1941, south Louisiana produced approximately 90,900,000 bbl. of oil, while north Louisiana produced approximately 27,000,000. South Louisiana, therefore, produced about 3¼ times more oil than north Louisiana. During the past year, 574,800,000 M cu. ft. of natural and casinghead gas were produced in Louisiana; thus 1941 gas production exceeded the 1940 production by 104,900,000 M cu. feet. Completion records for the year 1941 show that 1512 wells were completed in or adjoining producing fields. These wells, which were drilled to extend known producing areas or were located within producing areas, are not considered as wildcat wells. Of the total number of field wells drilled, 1152 wells found production; the remaining 360 were junked or dry and abandoned. This means that 76 per cent of the wells drilled were successful. Considering the precarious nature of oil-field development, this percentage of new producing wells is exceedingly satisfactory. Of the total number of field welis com-pleted as producers, approximately 86 wells found new and distinct producing sands. During the past year, 30 new fields were found. Four parishes—namely, Caldwell, Catahoula, Orleans, and Natchitoches— entered the ranks of oil-and-gas-producing parishes in the state during that period. This brings the total number of oil-and-gas-producing parishes in the state up to 48. Thus, 75 per cent of the parishes in Louisiana now contain one or more oil and/or gas fields. Although sufficient data are not available to list the addition reserves found in Louisiana during 1941, it is felt that such reserves undoubtedly exceed twice the total production for that year, or at least 200 million barrels. In reserves, therefore, Louisiana ranks third among the various oil-producing states. South Louisiana Although 16 new fields were found in south Louisiana, the outstanding developments in that part of the state were not limited to new discoveries. In fact, most of the increase in reserve in that area has been most consistently accumulated through extensions of known producing sands and through the finding of new sands in already productive fields, especially at depths below the presently producing sands. Since data concerning most of the new extensions and sands are too extensive for discussion here, the more important developments arc briefly outlined below: Abbeville, Vermilion Parish.—Production extended ½ mile to the west. Anse La Butte, St. Martin Parish.—New oil sand discovered at 9400 ft., thus extending production to east flank. West flank defined by dry holes. Barataria, Jefferson Parish.—New oil sand discovered on east side of field at 7620 ft. New

Jan 1, 1942

By C. L. HUSTON

MY ANCESTRAL connection with the manufacture of boiler plate runs back through four generations, and my personal acquaintance with the practice reaches back to the time, in my ,boy- .hood days, when iron plates' were made in a mill operated entirely by water power. -The mill originally was driven by an old-fashioned "'breast" water wheel 20 ft. in diameter and with a20-ft. face, geared direct to the roll train. When the mill slowed up and there was danger of its stalling, the men would jump upon the rim and help the wheel around with their weight, to prevent a "sticker." Later, as large plates were called for, a flywheel was set out of line so that it could' be speeded up by gears from the water wheel and connected back again,. by reducing- gears, to the roll train. The flywheel, with its cast-iron rim and wooden spokes, made 90 r.p.m. and the roll train 45 r.p.m. In 1870, our company installed our first steam-driven plate mill two-high rolls, 84 in. long. In these early mills the hot metal was manipulated by hand.

Jan 1, 1920

By AIME AIME

IN view of the approaching visit to Japan and the Imperial Steel Works at Yawata by our members, the following notes on present conditions in the industry there will be of interest. The data were collected by the representatives of the Bureau of Foreign and Domestic Commerce in Japan and are furnished here through the courtesy of the Department. In connection with the proposed suspension of both new and old Government undertakings and the general depression in building, which is expected to result from the retrenchment policy of the Government, some cuts in iron and steel prices have been made by dealers. It is expected that the Yawata Steel Works may reduce its round bar prices for November delivery by 1 yen.

Jan 1, 1929

By Orville R. Lyons

THE removal of moisture from coal has been a coal-preparation problem ever since the first wet-washing preparation plant was placed in operation. Today, when most of the coal produced in the United States is wetted at the working face when mined, or is cleaned by wet methods, the removal of moisture is a necessity for any one or a combination of the following reasons; (1) to avoid freezing difficulties during shipment, (2) to increase the B.t.u. content, (3) to effect savings in freight costs, and (4) to so improve the coal that it may be used for specific purposes-for instance, in the production of briquettes or the production of metallurgical coke-or so that it can be treated by dry cleaning methods. In general, the amount of water retained by coal particles varies with the size-consist of the coal. Fine coal has a larger surface area per unit weight than does coarse coal, so its capacity for retaining moisture is proportionately greater. The removal of moisture from coarse coal is relatively easy, while the removal of water from minus 10-mesh coal or finer is a major problem, usually requiring an individual solution at each preparation plant. As a result, a multitude of methods and a variety of equipment have been designed to solve both general and specific moisture-removal problems. Definitions In order that misunderstanding may be eliminated insofar as possible, it is necessary to define the terms to be used. The moisture content of any given increment of wet, washed coal is made up of two parts, inherent and surface moisture. Inherent moisture has been defined in various ways and as yet no standard definition has been agreed upon. However, in general, it is considered as the moisture that is present in the coal in the bed. The important point to remember is that coal with any amount of inherent moisture, whether 2 or 20 per cent, will appear dry if there is no surface moisture. Also important is the fact that inherent moisture can be removed, in part, by air drying at atmospheric temperatures. Surface moisture is that attached to the surface of the coal particles or that retained in cracks and fissures other than capillary openings in the coal substance. Essentially, insofar as the bituminous coal and anthracite indus-

Jan 1, 1950

By John L. Schroder

In selecting the best system of mining for a particular operation, many different factors must be considered. The system to be finally selected should be that which provides: 1) The highest possible degree of safety for mine personnel. 2) The lowest cost per ton of product. 3) The maximum coal production per man-shift. 4) The most suitable quality of final product, considering its intended use. 5) The maximum percent recovery of coal per acre of reserve consistent with cost and subsidence rights. 6) Consideration for the ecology of the area. Some of the important factors to be considered when choosing a method of mining are: 1) Amount of cover over the coal seam. 2) Type of the rock in the overburden. 3) Characteristics of the coal seam including: (a) the thickness of the coal seam; (b) the nature and location of any impurities or irregularities; (e) the dip (or pitch) of the coal seam; (d) the nature and direction of any definite cleavage ill the czoa1 seam; (e) the hardness of the coal; (f) the structural strength of the coal; and (g) the presence, anti amount, of explosive gas (methane). 4) Quantity of water likely to be encountered in the mining operation. 5) Nature and strength of the roof (top) over the coal seam. 6) Nature and strength of the floor (bottom) under the coal seam. 7) Any previous or concurrent mining in seams above or below the coal seam to be worked. Information on items 1-7 may be obtained in several ways. Topographical and geological reports and maps of the area are generally available

Jan 1, 1973

By Kalervo Rankama

UNTIL a few years ago, geological mapping, the study of ore boulders, and different geophysical methods were the principal means used in the systematic search for mineral deposits covered by a layer of disintegration products or soil. These methods have been developed to a high stage of perfection as far as the geometrical definition of the conductor is considered. Use of geophysical methods in prospecting is based on the fact that an ore body differs from the country rock not only geologically but also in its physical properties. The general drawbacks and complications included in the use of geophysical methods are well known to everyone who has been using them, so need not be entered into here in detail. One of the more important ones is the fact that geophysical methods are unable to furnish information concerning the chemical composition of the ore bodies responsible for the indications. Further, the ores of many metals, such as silver, gold, beryllium, zinc, mercury, tin, lead, vanadium, antimony, chromium. molybdenum, tungsten, manganese, cobalt, nickel, and the platinum metals cannot be directly located by known geophysical methods, owing to lack of physical characteristics suitable for distinguishing them from the country rock. Thus it is quite natural that efforts have been made to develop direct methods for prospecting and locating ore bodies of the elements named. Known as chemical, biogeo-chemical, and geobotanical methods of prospecting, these have been much improved during recent years. A brief review of these methods and of some results obtained with them will be presented in the following, on the basis of available information and my own experience.

Jan 1, 1947

By D. R. Walker, M. C. Shaw

Dimitri Kececioglu (Allis-Chalmers Manufacturing Co., Milwaukee)—The idea of applying metal cutting theory to comminution and vice versa is very impressive. Among others, the demarcation of wheel-grinding data into two regions, namely Kick's and Rittinger's, draws attention here. A study of Figs. 6 to 9 shows the following: In Fig. 6, 1 point out of 8; in Fig. 7, 4 points out of 26; in Fig. 8 only 1 point out of 13; and in Fig. 9 practically none out of 13 points fall out of curve No. 2. Also when grinding particles smaller than 5x10." in. it is difficult to measure very accurately the grinding forces, chip geometry, and particle size. In view of the above it would be difficult to make a positive and distinct demarcation of the Wheel-grinding data into two regions, namely, Kick's and Rittinger's. The idea of using machine grinding to determine the comminution properties of materials is indeed unique. The following cautions come to mind, however, regarding applicability of machine grinding data to comminution: 1—Grinding gives uniform particle size, whereas comminution gives a variety of particle sizes in the same process. The fact that grinding gives uniform particle size is not necessarily an advantage because in comminution the overall energy under actual comminution is desired and comminution invariably results in the production of a variety of particle sizes. 2—In grinding, a small particle is ground off a comparatively large surface. In comminution small bodies are broken down to smaller bodies. This makes it difficult to establish a concept of reduction ratio in machine grinding. 3—The mechanics of machine grinding involve direct shearing action under very high strain and comparatively high compression at the shear zone, whereas: comminution involves direct dynamic compression and surface friction with comparatively little strain and shear. Consequently the mechanics of machine grinding appear to be different from those involved in comminution. Hence one might arrive at erroneous con- clusions when comminution characteristics are eval-uated from machine grinding results. It is noticed also that functions other 'than Eq. 16 which do not involve the concept of direct proportionality of useful energy input to new surface area created (Eq. 2 and particularly Eq. 12) may be derived to fit the, data of curve No. 2. One such relationship may be u = ct-", where c is a positive constant and n is a positive constant less than unity. This, of course, is made possible because data of a very small range. of particle size are being fitted by the curves of No. 2 and the hereby suggested relationship. A sound comminution theory should be applicable to a relatively large range of particle size. George B. Clark (Department of Mining Engineering, University of Illinois)—While the experimental work of Walker and Shawin this article is of intrinsic value in revealing certain fundamental aspects of machine grinding, milling, and related processes and in adding to the store of information concerning the comminution of solid materials by this particular process, it appears doubtful that the results of their research can be employed to verify either Kick's or Rittinger's theories. Both these laws were originally developed and proposed on the basis of very simple, idealized hypotheses. The creation of parallel idealized physical laboratory conditions which would be required for either their proof or disproof appear to be well beyond the scope of human ingenuity, at least at present. One great weakness of the imputed verification is that the spread of the points plotted on the graphs is not sufficient to permit accurate 'curve fitting. The range of particle sizes included in the belt and wheel grinding is not extensive enough to show any general trends, particularly for the horizontal portion of the curves, said to represent Kick's laws. That the milling; grinding, and turning data obtained by Walker and Shaw for both metals and minerals happen to comply with. certain interpretations of these two theories under certain specialized conditions

Jan 1, 1955

John Birkinbine, Philadelphia, Pa.: Mr. Sperry's paper is certainly a valuable addition to the literature upon alloys with iron, supplementing the data already published concerning the influence of manganese, chromium, tungsten, titanium, aluminium, etc.; and it is to be hoped that the presentation of information upon the influences of nickel may bring out comparisons with other alloys. Taking into consideration the properties of nickel, and its use as an alloy in heavy forgings, as set forth in the paper, there would appear to be no serious difficulties in utilizing this alloy by extending its application to pieces of more moderate size. The melting-temperature of nickel, as stated by Mr. Sperry, is considerably lower than those given by various authorities. Its point of fusion being so near that of iron, and its density but little greater, the difficulty of alloying it in the foundry should not be serious, particularly if it is applied as a ferro-nickel. The addition of nickel monoxide (NiO) to molten steel would appear to be less desirable than the application of metallic, nickel or of ferro-nickel, if such is produced on a commercial scale and at a satisfactory price.

Jan 1, 1896

By L. Valentik

Many attempts have been made during the last 40 years to evaluate the performance of gravity separation equipement, that is, the effectiveness with which light and heavy particles are separated. The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris in 1950. The methods suggested by the Conference were accepted and very widely used in the last two decades. This paper discusses an improved method of evaluation in the light of the now-accepted standard presentation. The float-and-sink analysis of the product is presented on a Gaussian distribution curve, resulting in an easier visualization of the inherent difficulties of separation. The ogives of the distribution curve me then plotted, giving a quantitative measure of the deviation from perfect separation as an error distance instead of an error area. Illustrations of the new method are given both for gravel and for coal preparation, but the content is valid and applicable to other types of minerals which are separated by gravity methods. Many attempts had been made during the last forty years to evaluate the performance of heavy-media separation (HMS) equipment, that is, the effectiveness with which floats and sinks are separated.'-' The most comprehensive treatment of the subject was made by Cerchar at the 1st International Conference on Coal Preparation held in Paris. 6 The primary aim was the thorough understanding of the mechanism of separation and the unified presentation of data on gravity separation so that the evaluation and comparison of washery performance could be made from all over the world. No strict overall standardization has been achieved, but after the conference a more or less uniform presentation of performance was accepted, which, during the last two decades, has been very widely used. In this paper, illustration of the old methods and an improved method of evaluation will be given. HEAVY-MEDIA SEPARATION (HMS) PERFORMANCE CRITERIA In the ideal HMS process, all material lower in density than the specific gravity of separation (SGS) would be recovered as floats and all material of higher density would appear as sinks. In order to evaluate the misplaced material, the washery products are tested at the density at which the washing unit is operated. The original type of plot1,7, 8 is shown in Fig 1; this was developed primarily for coal cleaning units. The curve for raw coal represents the cumulative percentages of sink material. The refuse curve is also plotted as a cumulative sink, the percentages being expressed in terms of raw coal. This diagrammatic representation of the results of washing units has the merit of easy visual observance of the degree of separation obtained. The error areas (cross-hatched) are a measure of the amount of misplaced material and therefore they can be used to characterize the quality of separation. The ideal and actual separating performance between floats and sinks can be best seen from the partition curve developed by Tromp,2 where the ordinate is the percentage recovery of the sinks, and the abscissa is the specific gravity (Fig. 2). It can be seen from the shape of the curve that as the SGS is approached, the proportion of material reporting to the improper product increases rapidly. In fact, the SGS can be defined as the density of the material in the feed that is distributed equally between float-and-sink products. When the upper half of the curve is inverted, a shape similar to that of a Gaussian error distribution curve is obtained and therefore the analysis of gravity separation may be carried out by using the law of probability. The shape of the curve in Fig. 2 is determined partly by the density composition of the feed, and partly by the sharpness with which the unit separates floats from the sinks.9, l0

Jan 1, 1970

By Lawrence K. Nordell

This paper reviews practices used In the selection and sizing of belt conveyors and stacker systems commonly used in crushing and grinding plant facilities. Historical and modern methods of sizing this equipment are presented. The new methods Include: 1) probability theory applications for establishing component reliability, 2) "Monte Carlo" simulation techniques used in evaluating alternative system designs and in establishing service factors and corresponding availability Indices of each system, 3) quantifying the system and component operating characteristics using computer assisted modeling tools simulating rigid body and elasto-mechanic behavior for starting and stopping large and/or complex belt conveyors.

Jan 1, 1982

By W. E. Ruder

IT has been pointed out by Stead 1 that grains of considerable coarseness may be developed in steels containing from 3 to 5 per cent. of silicon, and in a previous paper 2 the present author has shown that under the proper conditions of annealing single grains having an area of 50 sq. cm. may be obtained. It is the purpose of this paper to discuss in more detail the conditions, promoting the growth of these grains, in the hope that the experiments described may throw some additional light upon the general problem of grain growth in metals. These silicon steels lend themselves particularly well to such experiments because of the ease with which the change in structure may be followed and because of the fact that the effect of the carbon present is largely obliterated by the high percentage of silicon. This forms a solid solution with the iron, which acts very much like a pure metal. This alloy has been found to have but one critical point, viz., Are. This point, determined by Roberts-Austen for Hadfield's 4 per cent. Si alloy, was found to lie at 703° C. Vigouroux3, in working with pure Fe-Si alloys, finds this point to rise from 750° C. for 0.5 per cent. Si to 860° for 6 per cent alloy, with a flat region in the curve from 3 to 4 per cent. Si. No accurate determination of this point has been undertaken by the present author, but it has been roughly determined to lie between 730° and 750°.

Jan 12, 1913

By H. A. Bedworth, W. H. Bassett

The amount of oxygen present in refined copper bears an important relation to the effects of various impurities on physical properties of copper, as well as the effects of reducing gases at higher temperatures. It seems fitting at this time, when the effects of reducing gases on copper are being discussed, to describe methods that have proved satisfactory for the determination of oxygen and sulfur, and to present some results obtained by investigation of these methods in the authors' laboratory. The procedure for the determination of sulfur is closely interrelated with that for oxygen and has, therefore, been included. It was first proposed by Hampe1 that oxides in copper could be accurately determined by the loss in weight sustained by finely divided copper when reduced at red heat in pure hydrogen, or by the weight of water produced. Hampe's method was later modified by Archbutt,2 who established the accuracy of the method and demonstrated that equally accurate results were obtained by noting the loss in weight or by weighing the water formed. The determination of oxygen by heating in carbon monoxide has been proposed by West.3 In our hands this method has given slightly lower results than obtained by heating in hydrogen. Heath4 found that the loss in weight after heating in hydrogen did not represent the true oxygen as cuprous oxide but included also gases derived by the metal from the fuel and refining in the furnace, and any trace of mechanically held moisture. He found, further, that the copper after ignition retained hydrogen equivalent to about 0.01 per cent. Heath proposed to determine the amount of occluded gases by preliminary ignition for 20 min. in pure carbon dioxide—and to correct the error caused by absorbed hydrogen by subsequent ignition and cooling in carbon dioxide, finally replacing this gas with air.

Jan 1, 1926

By W. P. Sykes

SINCE Honda and Murakami1 in 1918 proposed their constitutional diagram of the carbon-free iron-tungsten system, considerable effort has been expended by several investigators in attempts to define more positively the structural features of the alloys. The existence of an intermediate phase corresponding to the formula Fe3W2 (68.7 per cent W) was proposed from evidence of a purely metallographic nature by one of the present authors2 in 1926. Since that time the identity of this phase has been confirmed by Arnfelt3 and by Takeda,4 both of whom employed X-ray methods as well as the microscope and the chemical analysis of isolated microconstituents. According to Arnfelt, Fe3W2, as crystallized from the iron-rich melts at a temperature above 1450'C., contains by analysis 68.7 per cent W. The lattice of this phase is characterized by trigonal symmetry. Arnfelt, moreover, proposed a second intermediate phase formed at some temperature between 1450° and 1000° C. by a peritectoid reaction involving Fe3W2 and the iron-rich solid solution. A melt containing 25 per cent W was cooled to 1000° C. and heated for. 100 hr. The precipitated tungsten-rich constituent was separated and found by analysis to contain 62.6 per cent W. This composition agrees closely with that represented by the formula Fe2W (62.2 per cent W). Diffraction patterns from the concentrated precipitate showed a hexagonal unit cell. Takeda confirmed the data of Arnfelt regarding Fe3W2 but was unable to detect Arnfelt's second intermediate phase. While Takeda. failed to describe in detail the treatments employed, he stated that in alloys containing 40 per cent W which were quenched after heating at various temperatures between 1200° and 1450° C., no evidence of the second phase (Fe2W) was observed either in the microstructure or in the diffraction patterns of isolated residues. He therefore considered the existence of this low-temperature hexagonal compound as disproved.

Jan 1, 1932

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,' is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3' tests, however, this is not justified, and the D values

Jan 1, 1941

By Cyril Wells, Robert F. Mehl

The practical importance of a knowledge of the rates of diffusion of carbon and of alloying elements in steel has often been pointed out.l,13 This importance lies chiefly, though by no means only, in the study of carbufizing and in the study of reactions involved in the eutectoid inversion in steel. The present paper is one of a series in which the rates of diffusion of carbon and of alloying elements in ?-Fe and their mutual effects are measured with precision. The present paper reports the results of measurements of diffusion coefficients D of manganese in ?-Fe over wide ranges of temperature, and concentration, and of the effect of carbon and impurities and of grain size upon these diffusion coefficients.‡ Data on the rate of diffusion of manganese in ?-Fe have been reported by Fry2 and by Paschke and Hauttmann.3 Claussen4 calculated the diffusion coefficient D from Fry's data as 3 X 10-10 sq, cm. per set. at 960º, which will be shown to be incorrect by many orders of magnitude. Paschke and Hauttmann gave a rough value of 9.6 x 10-8 Sq. cm. per set. at 14000. Neither of these workers considered the variation of D with concentration and with temperature, and neither studied the effect of carbon. Method and Materials Method.—The method employed is identical with that used earlier.5 Owing to the volatility of manganese and the consequent loss of manganese from the outer surfaces of the welded diffusion bars, these surfaces were discarded. The diffusion anneals were performed in argon, except One (test 18) in which hydrogen was employed for purposes noted below. The temperatures reported are accurate to about 3" and constant within 1°C; the diffusion times are reported to the nearest half hour. The specimens were furnace-coo1ed after the diffusion ation, at about 2° per min. Layers, usually 0.004 in. thick, parallel to the welded interface, were machined from the specimens after the diffusion anneal and analyzed for manganese to 0.I Per cent Mn; the distances of these layers from the interface was measured to ±0.0002 in. The concentration-penetration curves obtained were analyzed by both the Grube and the Matano solutions.8 The D values calculated by these two methods do not differ appreci000. The Grube solution was used except in tests in which the effect of concentration upon D was greater than so per cent; in such cases the Matano method, which explicitly provides for the variation of D with concentration,' is the more reliable. In general, the number of layers machined from the zones of variable composition were large enough to permit the use of the average layer composition as that of the center of the layer. In 3 of the 3' tests, however, this is not justified, and the D values

Jan 1, 1941

By J. L. Huiatt, D. G. Foot

The Bureau of Mines, U.S. Department of the Interior, investigated methods of recovering potash values from process and waste brines. Laboratory pan evaporation of four chloride brines produced crude salts containing predominantly sylvite, halite and carnallite. Six sulfate- chloride brines produced crude salts containing primarily schoenite, kainite, leonite, sylvite, carnallite, and halite. Potash grades ranged from 7.2% to 22.2% K20, and recoveries by crystallization ranged from 85% to 99%. Sylvite flotation from chloride evaporites with amine collector, recovered 90% to 97% of the potash in a concentrate containing 54.3% to 60.3% K20. Fatty acid flotation of the high sulfate evaporite recovered 78% of the sulfate minerals in a 28%-K20 concentrate. Flotation of the remaining chloride minerals with amine collector recovered 80% of the potash in a 59.7%-K20 concentrate. Solar evaporation of 37 854 L (10,000 gal.) of brine recovered 99% of the potash in a crude evaporite containing 24.5% schoenite and 20% sylvite. Flotation in a 45-kglh (100-lblh) continuous flotation unit recovered over 95% of the potash in schoenite and sylvite concentrates, containing 28% and 62.3% K20, respectively. An economic evaluation is included.

Jan 1, 1985