Search Documents

By C. Feng, I. R. Kramer

A study was conducted to determine the influence of the surface on the yield point of fcc metals and high-purity iron. For the high-purity fcc metals, the yield Point produced by restraining a specimen may be eliminated by removing a sufficient amount of the layer. A yield point similar to that in fcc metals was found when iron specimens were pre-strained after a prior deformation. This yield point is not due to an aging effect but is associated with the surface layer. The yield points in age-hardenable aluminum alloy and those connected with "work softening" are not affected by a surface-removal treatment and are, therefore, caused by bulk-type dislocation reactions. The yield point which appears in previously strained fcc metals has been the subject of numerous studies. Several theories have been advanced to explain this "unloading-reloading" yield point. Cottrell and stokes,' from their study on the effect of temperature on plastic properties of high-purity aluminum, considered that it was the result of an avalanche "breakdown" of Lomer-Cottrell sessile dislocations. Haasen and Kelly2 extended this concept of dislocation-dislocation interaction to account for the yield point when unloading and reloading was carried out at the same temperature. On the other hand, strain aging was found to be responsible for the yield point in A1-Mg alloy by Westwood and Broom,3 and in aluminum alloys containing various amounts of alloying elements by Smallman, Williamson, and Ardley.4 In these cases, the yield point is considered to be associated with the locking of dislocations by impurity atoms. Birn-baum and filer5,6 and Takamura and muira7 reported that, when a high-purity copper specimen was prestrained, then held at a lower stress, and finally reloaded at the prestrain temperature, a larger yield point was observed. Such an increase was attributed to the locking of dislocations by point defects. In addition, Bolling8 suggested that both mechanisms, i.e., dislocation-dislocation interaction and strain aging, are responsible for the yield phenomenon, at least in a brass. Thus, there appears to be experimental evidence for both the strain aging and dislocation-dislocation interaction theories to explain the yield point in the fcc metals and alloys. In a previous article,9 one of the authors observed that, if sufficient amounts of metal were electrolti-cally removed after deformation of a high-purity aluminum single crystal, the yield point did not appear upon reloading. Continued pursuit in this area revealed that the effect of the surface on the yield-point phenomenon is not limited to one metal but affects a variety of metals of different lattice structures. Nor is the effect limited to the yield points produced by simple unloading-reloading at constant temperature; the surface exerts an important role on the yield point even when the temperature is changed at some stage during the test. It is the intent of the present article to give additional information regarding the effect of the surface on the yield-point phenomenon and to show the association between the yield point in both fcc and bcc metals and the existence of a heavy concentration of dislocation in the region near the surface of a deformed specimen.10 EXPERIMENTAL Materials. The single crystals used in this study had a nominal cross section of 0.125 by 0.125 in. and a 3-in. gage length and were prepared by a modified Bridgman technique. The initial purity for the metals was 99.997, 99.999, and 99.999 pct for aluminum, copper, and gold, respectively. Bar stock of these same materials was used in the preparation of the polycrystalline specimens of aluminum and copper. The iron specimens were machined from rods of "ferrovac", reported to have a purity of 99.98 pct. In addition, a precipitation-hardening aluminum alloy, containing 1.5 pct Cu, 2.5 pct Mg, and 5.5 pct Zn, was used. The polycrystalline specimens of iron, copper, and the aluminum alloy had a diameter of 0.17 in. and a gage length of 2 in. while the high-purity aluminum specimen had a nominal rec-

Jan 1, 1965

By B. VISWANATH

T HE Mysore iron works, at Bhadravati, about 2000 ft. above sea level in the Shimoga district of Mysore, British India, is served by a meter gage branch line of the Mysore State Railways. The works which were designed and erected by Perin & Marshall, who still act as consulting engineers, are surrounded by a thickly wooded country which sup- plies about 400 tons per day of wood for fuel. The ore deposits lie 20 miles to the south, and limestone quarries are close by the works. The Bhadra river sup- plies the works and the town with the necessary quantity of water. Dwelling houses for the employees

Jan 1, 1930

By J. Blodget Britton

To the question, " Do the Pennsylvania anthracites contain phosphorus?" asked at the last meeting of the Institute during the discussion on the metallurgical value of Western lignites, I can now give a definite answer. Through the kindness of a gentleman connected with the Philadelphia and Reading Railroad, and another connected with one of the principal ironworks on the Lehigh, there was sent to the Ironmasters' Laboratory a number of samples of the coals now largely shipped from the Schuylkill and Lehigh regions. Seventeen of these I examined for their contents of ash and phosphorus, and obtained results as follows : Ash. Phosphorus. No. 1, . 4.10 .0063 2, . . . . 7.97 .0209 113, . 5.53 .0049 114, . . . . . . . 6.55 .0056 . 5, . 5.39 .0761 . . . . . . . 11 6, 14.15 .0593 7, . 10 43 ,0049 rl 8, . . . . . . . 5.29 .0354 9, . . . . . . . 3.01 .0042 6L10, . . . . . . 3.03 .0042 1 1 . 275 .0014 12, . 2.82 ,0111 l'13, . .3.69 trace L1 14, . . .2.35 trace 15, . . . . . . . 7.22 .0014 16, . . . . . . . 3.49 .0167 17, . 4.63 trace

By F. G. Miller, E. B. Wilson

In 1972, coal mine productivity was in steady decline and labor and maintenance costs were spiralling upward. Yet, despite this sad state of affairs, nowhere in the US at that time was there a comprehensive and coordinated coal research and development plan in the offing. The Bureau of Mines had not yet been charged with such a responsibility, and industry was content to rely on machinery manufacturers for innovations. It was during this period that Bethlehem Steel Corp. determined that a new approach to coal mining research was needed for the industry as well as for the company itself. After studying Bethlehem's own mining practices, the state-of-the-art of mining research elsewhere, and development work by manufacturers, a comprehensive research package was presented to company management in late 1972. The ideas and experience of many operating and management personnel in the company contributed to the formulation of the final plan as approved.

Jan 10, 1976

By K. A. Gschneidner, O. D. McMasters, T. J. O’Keefe

X-ray diffraction, differential thermal, ad rnetallo-graphic methods were used to establish the Dy-Pb Phase diagram. Lead additions lower the 1377°C transformation temperature of dysprosium to 1360°C leading to an inverted peritectic reaction. The 327°C melting point of lead is lowered by dysprosium additions to about 326°C yielding a eutectic reaction. A second eutectic reaction occurs at 13.3 at. pct Pb and 1200°C. The dysprosium-richest intermetallic compound DysPb3 melts congruently at 1695°C and crystallizes in the hexagonal Mn5Si3 (D8,) type structure. The peritectic decomposition temperatures for the remaining compounds are Dy5Pb, at 1555C, DyPb2 at 955C, and DyPb3 at 880°C. A fifth compound near the DyPb stoichiometry exists over a 310°C temperature range decomposing at 1130°C by means of an inverted peritectic reaction and melting incongruently at 1440°C. The crystal structures of the compounds are discussed. A systematic study of the rare earth-lead alloy systems is underway in an effort to supply information concerning the alloying behavior of the rare earth metals. The Dy-Pb phase diagram is the fourth system to be investigated in this study. The Yb-Pb,1 Y-Pb,2 and Eu-Pb 3 diagrams have been published recently. Utilization of the rare earth series of metals as a research tool in this manner should yield a better understanding of alloy formation. EXPERIMENTAL PROCEDURE Materials. The lead used in this investigation was obtained from Cominco Products, Inc., and was specified to be 99.99 pct pure. The dysprosium was prepared in this Laboratory by the calcium reduction of the fluoride followed by distillation of the dysprosium. The major impurities in the dysprosium in ppm are: A1 (<40), Ca (400), Er (<50), Gd (<200), Ho (<200), Mg (<50), Si (30), Ta (400), Tb (<100), Y (<50), 0 (651, H (15), N (not detected), F (430), C (35). Alloy Preparation. Most of the alloys were prepared by melting weighed amounts of dysprosium and lead in sealed tantalum crucibles. The tantalum crucibles were sealed by are-welding in a He-Ar atmosphere welding chamber. Thus the alloys are in contact with He-Ar at about 1 atm pressure. Homogenization was achieved by holding them in the liquid state for about 1 hr, cooling, inverting the crucibles, remelting, and repeating the process at least twice. Since these alloys were prepared in sealed tantalum crucibles, chemical analysis for final composition was thought to be unnecessary. No detectable reaction of these alloys with the tantalum crucible was observed by metallographic examination. Metallographic evidence was also used to confirm the homogeneity of some of the alloys prepared in this manner. The compositions of a few alloys, which were prepared by nonconsum-able are-melting, were corrected for the small weight losses involved by assuming that the weight loss is due to vaporization of lead. The specimens obtained from the alloy samples were prepared under a dry-argon atmosphere because they were rapidly attacked by air and moisture. Thermal Analysis. Differential thermal analysis methods were used to determine the liquidus curves and reaction horizontals of the system. Both Pt vs Pt + 13 pct Rh and W + 5 pct Re vs W + 26 pct Re thermocouples were used to measure the temperature. An X- Y recorder was used to record the specimen temperature and differential electromotive force between the specimen and molybdenum standard. The arrest temperatures were measured potentiometri-cally. The accuracy limits (* values) associated with the reaction temperatures obtained by this method were estimated on the basis of both the reproducibility of the particular temperature value and the accuracy of the thermocouple at a given temperature. Liquidus temperatures were obtained from cooling arrest data while both heating and cooling arrest data were used to establish the horizontals of the diagram. Heat treatments during the thermal analyses of the alloys between 40 and 70 at. pct Pb were necessary in order to approach equilibrium conditions. The samples were held at temperatures between the various peritectic horizontals for l to 2 hr before the thermal analyses were continued. The entire range of compositions was investigated at the expense of a minimum amount of materials by adding appropriate amounts of lead to master alloys. More than sixty alloys were analyzed by this differential thermal method and for each alloy the results given herein are taken from two or three heating and cooling cycles. X-Ray and Metallographic Methods. Slice specimens for metallography and powder specimens for X-ray diffraction were prepared from rod-shaped samples which had been melted in sealed 0.62 5-cm-diam tantalum crucibles. The specimens were heat-treated in sealed tantalum crucibles which were protected by sealing them in argon-filled quartz ampules. Quenching was accomplished by breaking the ampules in ice water after heat treatment. X-ray powder specimens were sealed in 0.3-mm-diam glass capillaries under a dry-argon atmosphere. Copper, iron, and chromium radiation were used to obtain the powder patterns for these alloys. More than 150 powder patterns were obtained for specimens of various compositions and heat treatments. Included in these were several patterns for specimens which had purposely been oxidized. Patterns from specimens which had been accidentally exposed

Jan 1, 1969

By H. C. George

IN 1901, the United States produced 69 million barrels of crude oil, which was 41.4 per cent of the world production. By 1931, these figures were 850 million barrels and 62.1 per cent respectively, showing over this period of thirty years an increase in the world production of 718 per cent. Over this same period, the increase in the demand for technically trained men in the industry was much greater than the increase in crude-oil production. This was because much of the increase in production was secured by the application of geology and physics to the finding of new oil fields and by .the development of engineering methods and equipment incident to drilling and producing from much greater .depths.

Jan 1, 1934

By A. F. Giamei, E. J. Freise

A discussion of the various factors affecting the accuracy of volume fraction determination by the direct comparison X-ray diffraction method is presented. To minimize errors introduced by nonrandomization effects such as preferred orientation and large grain size, as well as errors introduced by statistical effects, an iterative mathematical analysis is introduced. This analysis is applied to all observable diffractio~ spectra from a given specimen by means of computer techniques and is statistically superior to the standard direct comparison technique which utilizes only one or tm sets of intensity spectra. The computer program also presents a graphical interpretation of- the results which enables the investigator to visualize and readily assess the scatter in volume fraction estimates caused by deviations from randomness. Finally, the iterative analysis is applied to experimental data collected from a series of plain carbon steels in both the as-received and spheroidized conditions to determine the volume fraction of cemen-tite present in each case. The results show markedly good agreement with chemical analyses for all spheroidized specimens. In theory, quantitative X-ray diffraction is a power-ful analytical technique for precise determination of the volume fractions of various phases present in a multiphase poly crystalline aggregate. There are two generally used methods; both utilize the fact that the intensity of a diffraction line of a particular phase is a function of volume fraction of that phase present in the aggregate. The more common method is the so-called internal standard technique where a known amount of standard substance is mixed with the aggregate containing the unknown. The resulting ratio of the intensity of a particular diffraction line of the unknown to the intensity of a diffraction line from the standard is used to find the weight fraction of unknown material by reference to the intensity data obtained from a previously prepared set of standards containing the same amount of standard material. The details of this technique are outlined in standard works on X-ray diffraction.&apos; The disadvantages of the technique are that it requires the use of powder specimens and that the powder mixture must be homogeneous near the surface to the maximum effective beam depth. The alternative technique is the direct comparison method in which the ratio of the intensity of a diffraction line of a phase in the aggregate to the intensity of a second-phase diffraction line yields the ratio of the volume fractions of each phase present. This method has been applied most extensively to the determination of the percentage of retained austenite in martensitic steels and to determining the amounts of hcp and fcc allotropic modifications in pure cobalt5 and the amounts of hexagonal and rhombohedra1 modifications in graphite.8 This method is applicable to bulk as well as powder aggregates and is the technique which will be considered in the following text. It is the purpose of the present communication to show that by combining the results of X-ray diffrac-tometry with the use of high-speed digital computers the results of the direct comparison quantitative X-ray analysis technique can be optimized by using all of the data available on a diffraction pattern. THEORETICAL DISCUSSION In optimizing any quantitative X-ray diffraction experiment, the problem of accuracy vs time to collect and analyze the experimental data arises. For any method to be practical, it is required that both experimental and analytical procedures are reasonably short. In most of the previous work performed by the direct comparison method, intensity data from only one or two sets of peaks were used to calculate the volume fraction of phases present in the aggregate. Consequently, rather long-time experimental measurements are required to assure that the intensity data are sufficiently accurate to justify the use of one or two sets of data. By using computer techniques to analyze the experimental data it becomes feasible to use all of the available data on a diffraction pattern. By so doing, the time spent in measuring any one diffraction maxima can be appreciably reduced. Although this results in poor counting statistics for any one maxima, the number of data points available for analysis is greatly increased. Based on the above discussion, it will be assumed that a continuous scanning counter-diffractometer technique will be used to collect intensity data from a two-phase mixture. The integrated intensity of the ith diffraction line from the a phase in the aggregate is given by:&apos;" where is the volume fraction of the a phase, The various quantities in Eq. [la] are angular independent while those in [lb] depend on the hkl spectrum of a particular phase. The meaning of the individual quantities in Eqs. [la] and [lb] are given in Appendix 1. It is convenient at this point to outline briefly the factors which will affect the measured intensity of any one hkl spectrum. a) Extinction effects arise from two independent experimental conditions. Primary extinction arises from a high degree of crystal perfection and results in spectra having lower intensity than predicted by Eq. [I]. Any treatment, such as powdering, which reduces

Jan 1, 1968

By R. A. L. Black, J. E. Jennings

The problems of slope stability in open cast mines are examined. A criterion, the instantaneous stripping ratio, is suggested for use in the design of pit slopes and as an index of control at all stages of the exploitation of the orebody. This criterion may also be related to safety and to the maximizing of profits. Two approaches to safe design of slopes, one from the point of view of soil mechanics and the other from the point of view of rock mechanics, are described and critically compared. The effect on slope stability of the regional tectonic stress field is discussed. Explanation is given of the application of the Terzaghi effective stress concept to problems in both soil and rock environments, including possible effects when borehole deformation techniques are used to measure stresses in rock in situ. A company embarking on open cast mining is faced with two basic questions: 1) will the venture be profitable and 2) can it be carried out with safety? The two questions are obviously interrelated because both depend upon the slope angles adopted for the pit. The cost of open cast mining depends largely upon the stripping ratio, defined as the volume of overburden that must be removed to the volume of ore recovered. The steeper the slope angles, the more favorable the stripping ratio, but the stability of the slopes, and therefore the safety of men and materials in the pit, require that the angles be made relatively flat. Consequently, the design depends upon a compromise: the slopes must be steep enough to result in economical mining and flat enough to ensure safety. Today there is a world trend towards deeper mining by open cast methods. This is mainly due to the higher cost of underground mining and the lower cost of open excavation resulting from the introduction of large modern earth and rock-moving machinery. Deeper open cast mining has led to a very great increase in the volumes of wasted overburden, and much thought is being given to the considerable economic benefits which would result if pit slopes could be made steeper by even one or two degrees. The result has been an increasing interest in research into slope stability problems in the expectation that the application of scientific principles will provide solutions leading both to economies and to more predictable operation of the mines. In at least four places, the U.S., Australia, Western Germany and Southern Africa, comprehensive investigations are at present in progress, and it is the object of this paper to review some of the more important aspects of these programs. RELATION BETWEEN ECONOMY OF OPERATION AND SLOPE ANGLES The main object of any industrial enterprise in a free economy is to make a profit. In mining, where profits must be made from a wasting capital asset, a further definition of the profit motive is imposed, namely that the economic aim should be to maximize the total possible profit. But since profits deferred for a number of years are not as valuable as profits that are immediately available, it is usual to discount deferred profits at some rate of interest which reflects their current or present value in the hands of the investor. Thus, in mining the logical aim can be defined more closely still: to maximize the present value of the total future profits. In commercial terms the present value represents the market value of the operation as a going concern. Many factors enter into the forecast of current and future profits. They include the volume of production, the price of the salable product and the cost of production. Current profits can be estimated with reasonable accuracy by the operating engineers; but it is the task of economists and management to assess future trends in the mineral markets and in the economy as a whole, and together with the engineers, they can then estimate the future cost and profitability of the mining operations. In open cast mining, the rate of ore production once decided on remains a virtually constant factor unless a major change in the capital structure of the mine is made. But one factor over which the operator has a considerable measure of control is the ratio of the volume of ore mined to the volume of waste over-

Jan 1, 1963

By Elliot Rexford

The quality of aggregate materials is of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 3, 1950

By T. R. Wright

IN few mining regions in the world are the ores so varied and complex as in the Andes of central Peru. Consequently, in few localities is one company engaged in so many and such diverse metallurgical operations as the Cerro de Pasco Copper Corp. Concurrent with the mining of complex lead-zinc ores in Peru, and the consequent expansion of the Corporation&apos;s metallurgical activities, a department of metallurgical research was established in 1927 at La Orova. Facilities were provided for research in ore dressing, hydronivtallurgy pyrometallurgy, electrometallurgy, and analytical chemistry. In addition to laboratories. various pilot plants were built, including a concentrator, leaching plant, "by-product" smelter, and electrolytic refineries. These pilot plants are not diminutive units; they are designed and equipped as semicommercial plants for operation on a continuous 24-hour basis thus assuring the duplication of pilot plant results in actual practice. In general, the sequence in the development of metallurgical operations hasbeen as follows: (1) investigations in the laboratory to determine the most effective and economical method of treatment; (2) continuation of the research project on a pilot-plant scale when the evaluation of the laboratory

Jan 1, 1945

By AIME AIME

SECTION DELEGATES were given an opportunity to see how the machinery of Institute administration functions, on Tuesday evening, Feb. 16, when they were the&apos; guests at the regular monthly meeting of the Directors. Of the new board of 25 members, 19 were present at the meeting, including directors from Seattle, Los Angeles, Wyoming, Oklahoma, Chicago and Pitts-burgh, the new junior past-president from Jerome, Ariz., and the new president from .Washington, D. C. The complete list of the 72 in attendance at the dinner,: held in the main dining room of the Engineers&apos; Club, which pre-ceded the general session of the Directors&apos;. meeting, follows:

Jan 1, 1932

By R. W. Gurry, L. S. Darken

The solubility of cementite in austenite is computed by thermodynamic methods from the observed solubility of graphite. It is found that the solubility of cementite is greater than that of graphite in the entire austenite temperature range. Thus the prior discrepancy between this portion of the phase diagram and the observed metastability of cementite is partially resolved. FOR several years it has been apparent that a serious discrepancy exists in certain observations pertaining to the Fe-C system. Direct experimental data indicate: 1-That the curve representing the solubility of graphite in austenite&apos;" crosses that for cementite4 at about 945°C as shown in Fig. 1. 2— That graphite and austenite saturated therewith are stable1 relative to cementite at all temperatures between the eutectoid, about 723°C, and the eutectic, about 1153°C. These observations are mutually incompatible in view of a well-known consequence of the second law of thermodynamics, namely, that the stable phase (presumably graphite at all temperatures) has a lower solubility than the metastable phase (presumably cementite). Hence either 1 or 2 above must be in error; either the measured solubility of graphite or of cementite, or the observation as to the stability of graphite, is in error. Our present purposes are: 1—To collate the available data on cementite and prepare a table of HO — HO° and of (Fa— HO°)/T. This tabular method seems the best and most convenient way to represent the heat and free energy of formation. 2—To determine whether the measured solubilities of cementite and graphite in austenite are in accord with the above table and the measured thermodynamic properties of austenite, in order to resolve, if possible, the existing paradox of these two solubilities. Enthalpy of Cementite The enthalpy of cementite at 273 °K, H279 — HOcem, was computed by integration of the low temperature heat capacity as measured by Seltz, McDonald, and Wells" 68" to 298 °K) and as given by the Debye functions recommended by them (0" to 68°K); the result is included in Table I. At higher temperature HCem — H,,"" is given by Kelley who used the data of Naeser7 (298" to 1037°K) and of Umino8,9 (273° to 1923°K). We have recalculated Hcem — H273 cem from the data of UminoO in the following way. In the equilibrated alloy at temperature the weight fraction of cementite Pct c -Pct cr is PctC -PctCr designated f(C), and the

Jan 1, 1952

By W. E. D. Stokes

WHEN history is written, the year of the blitzkrieg will go down as giving aviation its greatest impetus. No perceptible drop in military business, even with cessation of hostilities abroad, seems likely. The combined air force of the U. S. Army and Navy on July 1 was approximately 5000 planes, as against 50,000 planes currently discussed as necessary. Observers at the fronts are giving designers and metallurgists back home some realistic ideas to shoot at. As conventional runways reveal the location of airports to enemy raiders, operating bases are now masked. Difficult, often muddy and rough landing strips, requiring strong landing gears and exacting take-off and maintenance characteristics, are the specifications of war. This is "old stuff" to numerous mining operators in mountainous jungle areas where gradients up to 8 per cent are in more or less common use in such mountain landing fields. Although airplane building is not readily adaptable to assembly-line methods, a trend towards mass productions is now in evidence. Incidentally, a U.S. Army "Curtiss P-40" requires about 10,000 man hours of work to complete and is tied together with 75,000 rivets. During the past year a number of aircraft factories adopted the "shot-

Jan 1, 1941

By Bruno Nordberg

HOISTING is one of the earliest endeavors of man with machinery, for hoisting was probably used by the early Egyptians. Treadmills were used for general hoisting until early in the nineteenth century and it was a short step only to attach a Watt steam engine to the rope drum of a hoist. One of the earliest steam hoists was built for a coal mine at Frisne, near Valenciennes, France. It was a remarkable piece of engineering created by James Watt in 1811, using a wooden drum on a vertical shaft. This followed the crude hoist by Holtzhausen in 1803, which used a drum of wood on a horizontal shaft.1 In this country there were examples of crude mine hoists, which have been developed into the efficient machines in use today. African and Australian mines show examples of both extremes, and have an array of fine hoisting equipment exemplified in those built by British manufacturers. The influence of both English and American engineering in hoisting is interestingly evident in Canada. The information available to the writer does not reveal this to be true of South Africa, although American-built hoists have been furnished. Mining camps develop their own style of equipment, adapted to local conditions. For instance, the Butte mining district adheres to the straight drum with friction clutches, because of the great number of levels from which hoisting is done or to which men and material are lowered and the necessity for hoisting or lowering unbalanced. The north Michi-gan copper country uses both straight and cylindroconical drums and hoists continually in balance, so that the drums are not clutched to the main driving shaft. The Joplin mining district, Missouri, has its own peculiar small hoists. Other individual mines or localities in which a number of mines have been developed show individualisticc types of hoists, depending upon their particular problems. In each instance, however, the particular problem must be carefully analyzed, as conditions are seldom so near the same that a number of identical hoists can be used to advantage.

Jan 1, 1940

By Ottar Dragge, C. Danielsson, Bo Kalling

DISCUSSION, T. L. Joseph presiding L. F. Reinartz (Armco Steel Corp., Middletown, Ohio) —I would like to know, in the practical application of the Kalling process, what kind of a lining was used, how thick was the lining, and how much metal was treated at one time? S. Fornander (author&apos;s reply)—The rotary furnace is lined with a course of fireclay bricks 6 in. thick. This course is backed by 5 in. of insulation. The furnace has a capacity of about 15 tons. Mr. Reinartz—How was the ladle preheated? Mr. Fornander—As pointed out in the paper, the furnace was heated by a gas flame in the beginning of the experiments. During these first tests, however, the desulphurization was inconsistent. We think that this was due to the fact that iron droplets sticking to the furnace walls were oxidized by the gas flame. Now, the furnace is operated without preheating of any kind, and the results are much better. T. L. Joseph (University of Minnesota, Minneapolis, Minn.)—I might add one comment. This furnace was heated with a flame and for a time they had a little difficulty due to some residual metal in the rotating drum that would oxidize in between treatments and they found therefore, that it was very essential to drain the drum completely of metal so that they would not build up any ferrous oxide between treatments and they eliminated some of their erratic heats by maintaining those more reducing conditions. It was interesting to watch this operation. As soon as the drum started to rotate there was considerable flame, at least, at the time I saw it, that came out around the flanges, indicating there was quite a little pressure on the inside of the drum. W. 0. Philbrook (Carnegie Institute of Technology, Pittsburgh)—Is the reaction slag in the Kalling process liquid or solid, and how is it separated from the metal? Mr. Fornander—In the process there is no slag in the usual sense of the word. The lime powder does not melt during the treatment. After the treatment the lime is still in the form of a fine powder. It is separated from the metal by means of a piece of wood of suitable size placed within the furnace before it is emptied. D. C. Hilty (Union Carbide & Carbon Research Laboratories, Niagara Falls, N. Y.)—Dr. Chipman has given us some of his ideas in connection with a specific effect of silicon and silica on sulphur elimination and how silicon might interfere with desulphuriz- ing in the blast furnace. I wonder if he would like to elaborate on the possibility of a similar effect of silicon in the Kalling process? J. Chipman (Massachusetts Institute of Technology, Cambridge, Mass.)—Silicon does not interfere with the Kalling process. Anything that has strong reducing action is good for desulphurization. In these tests where the temperature was low compared to blast furnace temperatures, the silicon that is in the metal is a better reducing agent than the carbon. At high temperatures, carbon is the better. It is not the silicon in the metal that interferes with desulphurization, it is the silica in the slag. Mr. Joseph—I might add that the metal that was tapped from the drum after desulphurization was really at quite a low temperature. It was not measured, but I think it was well under 1300 °C, probably 1200" or a little above that. That was one of the difficulties, and I think there is no question about the fact that the Kalling process—in that it affects desulphurization between powdered lime, solid and liquid iron— is a reaction definitely between the solid lime and the liquid iron. E. Spire (Canadian Liquid Air, Montreal, Canada) — This Kalling process seems very interesting to us and after all it is only a mixing action that is taking place between the iron and the slag. We have attempted to do the same thing in another way. We have placed at the bottom of the ladle a porous plug through which we injected an inert gas. It can be nitrogen or argon. This plug is placed at the bottom of the conventional ladle and gas injected through the plug. That has appeared in our patent. To define this new type of treatment, I use the word gasometallurgy. I do not know if you like it, but it is a way of defining methods of treating metal using gases. What we do is exactly what is done in the exchange process in another way. We have a porous plug at the bottom with a high lime slag on top of the metal. Using this method, we have very good agitation of metal and slag, and with a small flow of gas, we can achieve a very strong agitation. For instance, in the 500 lb ladle, we use only 5 liters of gas a minute. We have an agitation compared to very rapidly boiling water in a pail. Moreover, the agitation can be controlled to create any amount of mixing desired. In a few minutes, with this method, the sulphur dropped from 0.58 to 0.11. These results have been improved since, and we have obtained results like 0.08

Jan 1, 1952

By E. B. Hunt

Paraffin deposition has been studied in the laboratory under conditions simulating deposition in well tubing. A theoretical analysis has been made of the cooling of the oil and the precipitation of paraffin from the oil as it flows up the well tubing and through surface flowlines. It is proposed that paraffin deposits are initiated by the precipitation of paraffin directly on or adjacent to the pipe wall and grow by diffusion of paraffin from solution to the deposit. This mechanism is consistent with laboratory and field observations, and has proved useful in the design and interpretation of laboratory paraffin-deposition tests. Tests have been made of the effect of plastic pipe coatings and chemical additives on paraffin deposition. INTRODUCTION Paraffin deposits which form in well tubing and surface flowlines interfere with production and must be removed. Over the years much progress has been made in developing and improving methods of removing these deposits after they form. Much less progress has been made in developing methods of preventing or inhibiting the formation of paraffin deposits. This is due, it is believed, to the lack of knowledge of the mechanism of paraffin deposition, the absence of satisfactory laboratory testing methods and the difficulties in evaluating the results of field tests of preventive treatments. The present investigation was undertaken to elucidate the mechanism of paraffin deposition and to develop suitable laboratory tests for studying the inhibition of paraffin deposition in well tubing and surface flowlines. Current theories on the mechanism of paraffin deposition have been evolved from field observations, from laboratory studies of various factors which might be involved in paraffin deposition, and from laboratory paraffin-deposition tests.1-9 Paraffin deposits have been formed in the laboratory by immersing a cold finger into a hot wax-oil solution and by flowing hot wax-oil solutions through cooled pipe or over cooled plates. These laboratory conditions differ in important features from field conditions, and the observed deposition behavior is not entirely field-like." Thus, there is reason to question the field applicability of the results of these tests. The present investigation was undertaken to determine how to perform and interpret laboratory paraffin-deposition tests to obtain information on the inhibition of deposition in the field. The paraffin problem in the broadest sense encompasses the formation of any predominantly organic deposit in well tubing, surface flowlines and other equipment in contact with crude oil or gas. The present investigation was limited to paraffin deposition involving the precipitation of paraffin wax from solution by cooling and its concentration in a deposit on a cooled surface. This probably excludes its applicability to those problems arising from asphaltic-base crudes, but not those arising from paraffin-or mixed-base crudes. This also excludes its applicability to emulsion and congealing oil problems which are often included as part of the paraffin problem. The phenomenon of cooling appears to be the controlling factor in paraffin deposition involving the precipitation of paraffin wax and its concentration in the deposit. Deposits of this type are usually found in the field only where cooling occurs. Early in this laboratory investigation, it was not found possible to form deposits under constant temperature conditions from a wax-oil slurry, either by steady flow through pipe or by gas-lift up a pipe. Thus, the investigation was limited to situations involving cooling. THEORY The relationships involved in establishing the temperature profiles in an oil stream as it flows up well tubing with a linear (geothermal) pipe-wall temperature distribution or through surface flowlines with essentially constant pipe-wall temperature are presented in the Appendix. The relationship between radial distance in the pipe and the rate of cooling of the oil is then combined with a relationship between cloud point and rate of cooling to develop the pattern of formation of a wax cloud in the oil. The following discussion of paraffin deposition under various laboratory and field conditions is based upon this development which is presented in the Appendix. PARAFFIN DEPOSITION IN SURFACE FLOWLINES The average temperature of the oil coming out of a well is somewhat higher than the ground temperature. Thus, the oil continues to cool on its trip through the surface flowline, and wax deposition can occur. The temperature distributions calculated from Eq. A-4 are given in Fig. 1. As can be seen, almost all the cooling occurs in the first 500 ft from the wellhead. In addition, the radial temperature gradient near the wall decreases rapidly with distance and becomes very small after a few hundred feet. Thus, growth of a paraffin deposit would be expected to decrease rapidly with distance from the wellhead and become negligible after a few hundred feet, since growth is dependent on concentration gradient. Wax precipitation and diffusion of wax to the already

President H. M. Howe, Boston, Mass. (communication to the Secretary): Le Chatelier&apos;s pyrometer is certainly a most convenient and accurate instrument for the laboratory, and one that may be used under some conditions in the mill. I have used it for several years and with great satisfaction. Like Prof. Roberts-Austen and unlike Herr Blass, I have always found that its indications remain constant over long periods. Like Prof. Roberts-Austen, also, I find it possible, in a quiet place, to read with extreme accuracy ; and, by the use of a telescope, I can read temperatures to within a degree, for some delicate determinations which I have in hand. Variations in the temperature of the room affect the readings of the instrument far less than one would expect. When the current is cut off, the mirror does not always return exactly to the same place; in other words, the zero shifts appreciably, and must be determined often, indeed every few hours if accuracy be desired. In some cases I have had it determined within a very few minutes of every important reading. To this end a switch should he introduced, so that the circuit may be broken readily. With this arrangement we can determine accurately the position of the zero within a very few seconds of the time of taking any especially important reading. The chief causes of the variation of the zero which I have noticed are as follows: a. The suspension may not be tight enough, so that the momentum of the galvanometer frame as it swings makes its supporting wires slip in their bearings. b. Changes in the position of neighboring iron objects may deflect the mirror. c. Changes in the temperature of the room may, perhaps, change the torsion of the suspension wires, and so shift the mirror. d. Dust may attach itself to the galvanometer frame, and by friction against the surrounding fixed parts of the galvanometer, may

Jan 1, 1895

By Thomas M. Barczak

This paper describes a computerized simulation system developed by KETRON, Inc., in cooperation with the US Bureau of Mines. The system is designed for use by mine managers and engineers rather than computer specialists and allows the novice user to arbitrarily create room-and-pillar mine plans, with the computer illustrating the simulation of face activities on a video screen. Extensive visibility of the simulation is provided by visual display of the machine elements and their movement in the section to accommodate the extraction, roof control, place changing, and haulage operations. Performance statistics are also generated to analyze the operations. Both conventional and continuous mining methods can be simulated. In addition to simulating arbitrary scenarios, the system can also be used to display actual time-studied operations and maintain a file of these activities. Practical applications and case studies are provided in the paper to demonstrate the usefulness of the system. The system is designed to operate on a desk-top mini computer and is currently installed on a Hewlett-Packard 9854B system with 450 K bytes of memory.

Jan 1, 1983

By N. S. Wagner, R. S. Mason

The production of lightweight aggregates in Oregon is a new industry, and, like all new enterprises, it is suffering from growing pains characterized by numerous, small operations some of which flourish for a short time and then cease altogether. Norinally all industrial mineral products are produced in a highly competitive atmosphere. At the present time this condition does not exist to a very marked degree in the state because as yet producers have not saturated the constantly expanding market. This paper has been prepared with the intention of outlining very briefly the current status of the various products now heing used as lightweight aggregates in Oregon. The present piche will surely change, perhaps quite radically within even a short space of time. Lightweight Aggregates Used in the Northwest PUMICE Interest in Oregon pumice is not new. Deposits are abundant. Successful development, however, dates only from 1946. During 1948 a total of nine operations was engaged in full or part-time production of aggregate. The postwar building boom and increased public consciousness regarding the value of insulation are the immediate reasons behind the current development. Just how firmly this production of pumice aggregate may be established is something which cannot be foretold at the present time. Much will depend upon how successfully the pumice aggregate construction already installed stands the test of time. Some fine pumice aggregate products have been made and it seems probable that because of its unique properties a certain demand for pumice aggregate will continue in the future. Fire-proof, rodent-proof, decay-resistant properties supplement the lightness in weight and insulation properties of pumice aggregate products in rendering them particularly ideal for many types of construction. In addition there has been fabrication in the form of reinforced fence posts, street markers, and similar products of a specialized-product nature and these are not to be overlooked in terms of future production. Also pertinent to how soundlj pumice aggregate production is established will be possible future competition with other lightweight aggregates. However, this situation will be governed largely by competitive costs of production and marketing. For its present use, which is almost exclusively limited to the manufacturing of building blocks, the market for Oregon pumice aggregate has been extended from the mining area around Rend and Chemult to points as far distant as San Francisco and Seattle. Naturally enough the bulk of the production goes to the Portland and eastern Oregon consumers. Shipments are made by both rail and truck. Early in 1947 the State Department of Geology and Mineral Industries made a canvass of all pumice producers in the state. The production for 1956 amounted to 26,614 cu yd and was valued at $13,649 at the plants. The United States Bureau of Mines estimates the production for 1947 as 33,240 short tons valued at $111,380. This is roughly 65,000 cu yd. No data are available for the 1948 production but it is understood to exceed that for 1947. The Oregon pumice occurrences originated largely from the eruption of Mount Mazama, the name of the formerly active volcano and the location of Crater Lake. Other lesser volcanoes throughout the area contributed to the present occurrences, however, and it has been estimated by Moore&apos; that the pumice deposits cover an area of some 3500 square miles. This area lies east of Crater Lake between Bend and Klamath Falls and embraces the southern portion of Deschutes County, the northern part of Klamath County, and the northwest corner of Lake County. Thickness of the pumice ranges from thin skims to local thicknesses of as much as 30 to 40 ft. Fragment size also varies greatly. Any attempt to describe the situation by giving screen analyses would be confusing because of the wide variations to be found in all area of this size. The picture can best be summed up by stating that places showing great variations in fragment size can be found if a search for extremes is made. For mining purposes in connection with aggregate production, it call be stated that miles and miles of pumice exist in which the fragrnent sizes range from an inch or so downward. The usual color of the pumice is a light gray to off-white. A typical pumice analysis shows a silica content of about 69 pct, alumina 15 pct, and sodium oxide about 5 pct. Potash, lime, and water are the next three most abundant constituents, running just a little over 2 pct each. Iron oxides are fairly constant at 2.75 pct. Titanium, manganese, magnesium, and phosphorus occur in amounts of less than 1 pct. All of the foregoing substances are combined as a glass exhibiting cellular structure. The weight of crushed but otherwise pit-run (undried) pumice runs around 1100 Ib per cu yd according to figures furnished by various producers. The minimum and maximum weights per cubic yard reported are 1050 and 1400 lb, respectively. The 1400 lb per cu yd pumice contrasts with the pumice from most of the other

Jan 1, 1950

By Walter Crafts

STRUCTURAL steels containing chromium have become widely used in the last 20 years. In the earlier part of this period the major applications were in chromium-molybdenum aircraft tubing and similar special high-strength steels. During the past 10 years there has been a notable expansion in the use of chromium-bearing steel for structural purposes when welding was utilized for fabrication. The chromium-bearing steels introduced by Saklatwalla1 (chromium-copper), Kinzel2 (chromium-manganese-silicon), and Schultz3 (chromium-copper) are being extensively used at the present time.

Jan 1, 1939