Search Documents

By Reuel A. Cochrane, Harry H. Angst

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Harry H. Angst, Reuel A. Cochrane

The successful exploitation by opencut methods of the low-grade porphyry copper deposits is due to the economical handling of large tonnages. Large tonnages are possible only if the rock material is broken so that the large power shovels can operate with minimum delays. This is particularly true at the New Cornelia mine, where the dense, hard, tough rock material creates problems not encountered in most of the porphyry copper mines. The introduction of churn drills at the New Cornelia for primary drilling, in 1936, necessitated a complete change in the methods of breaking ground as formerly air drills had been used. The blasting operations are of particular interest because of the handling of great quantities of high explosives in safely and efficiently fragmenting the hard rock material. Rock Formations At the New Cornelia mine the rocks are quartz monzonite with a diorite border facies intruding a rhyolitic series. Overlying these formations is a fanglomerate formation composed of boulders of monzonite, diorite, rhyolite, and other types of rock of unknown derivation. (The word "fanglomerate" is used in this paper in referring to the local conglomerate type of rock formations.) The ore body is approximately 4800 ft. long and 2800 ft. wide, and is of the disseminated type. Mineralization occurs principally in the quartz monzonite and to some extent in the adjacent diorite and rhyolite. The principal ore minerals are chalcopyrite, bornite, and a small amount of chalcocite. Over a considerable area the quartz monzonite is extremely hard and siliceous in character, owing to pegmatitic zones of alteration. The hardness of the ground depends on the intensity of the silicification. In a small area in the pit, the monzonite contains an abundance of pyrite accompanied by sericitization and is soft and easily fragmented. This is true also in the remaining oxidized portion of the ore body. The diorite and rhyolite formations, like the monzonite, vary from extremely hard to very soft material, but on the whole are easier to fragment than the monzonite. Jointing is prevalent in all the rock formations and plays an important role in the blasting efficiencies. In the fanglomerate formation, numerous well-defined joints, widely spaced, tend to make the ground blocky when blasted. This is a deterrent to good fragmentation. In the other rocks the joints are more numerous and are closely spaced, except in localized areas where the formations are extremely hard. These descriptions indicate that the lowest blasting efficiency will be obtained in the harder formations, from which the major portion of the mine production is obtained; namely, the monzonite and rhyolite. All rock formations mined at the New Cornelia pit are so hard that excavation

Jan 1, 1943

By Frank F. Poland

TEE purpose of this paper-is to describe a new process for the refining of secondary copper-base metals and a specially designed high-temperature electric-resistor furnace used in the process for the distillation of zinc from these metals. The process was used for the conversion of nickel silver to cupronickel and to recover the zinc content in metallic form. It also proved applicable and economical for the treatment of scrap brass for separating and reclaiming the copper and zinc. The relatively large furnace developed for the distillation of zinc is described in detail, for it made economically possible the direct recovery of metallic zinc from scrap brass, which is a new step in the processing of such material. Considerable interest has been shown in the utilization of the distillation furnace for other metallurgical processes, where it is of advantage to operate in a controlled neutral or reducing atmosphere, or to avoid having the processed metal in contact with refractories other than carbon, or to operate at temperatures between 3000 and 4000°F. PURPOSE OF DEVELOPMENT It was recognized early in the war effort that nickel would become a critical metal, therefore all nickel stock and alloys containing relatively high percentages of nickel were frozen immediately. Among these alloys were considerable quantities of various grades of nickel silver, an alloy containing copper, nickel, zinc, and in some grades lead, also minor amounts of iron, manganese and other constituents. At the time there was no existing plant or process to eliminate the zinc, lead, and minor constituents so as to convert this metal to cupronickel, one of the important alloys needed by the U. S. Navy for condenser parts. Therefore the Bureau of Industrial Conservation of the War Production Board requested the executives of the leading nonferrous metal companies to have their metallurgical staffs study the problem of converting this metal to cupronickel conforming to U. S. Navy Specification 44T40. The composition specified therein is as follows: nickel, 29 to 32 per cent; zinc, 1.00; iron, 0.00 to 0.60; lead, 0.05; tin, 1.20; manganese, 0.00 to 1.00; total of other elements (maximum), 0.50; copper, remainder. The problem in converting these alloys to cupronickel was the elimination of zinc, lead, iron, manganese, and other elements without appreciable loss of nickel to slags or other by-products. Revere Copper and Brass Incorporated, through its Research and Development Department, undertook to solve this problem. A Government-owned plant was built at Rome, N. Y., and there the con- version was successfully made.

Jan 1, 1946

By Howard N. Eavenson

DURING the past year, as in the preceding ones, prices continued to fall, production to decrease, and more mines were closed. Much attention is being given by the industry to suggested plans for betterment of its position, and if the scheme recently brought out for consolidation of sales agencies into district agencies is loyally carried out, it cannot but help to improve conditions. The progress in the anthracite industry is shown in the report of its chairman, E. H. Suender; changes in coal preparation are outlined in the report of J. B. Morrow, chairman of Committee on Coal Preparation, while increased mechanization of the western mines is described by Eugene McAuliffe, chairman of the Committee on Machine and Strip Mining. In spite of the depression, interest in the Coal Division has been increasing, its meetings have been well attended, and its committees are active and have been doing excellent work.

Jan 1, 1932

By M. Semchyshen, G. A. Timmons

The predominant orientation in both straight-rolled and cross-rolled molybdenum is the {100} [110] texture. Upon complete recrystallization, this same texture predominates, but there is less spread about the ideal orientation. A secondary orientation about the [111] direction as the axis develops in cross-rolled sheet. Compression-rolled sheet exhibits random orientation in the plane of the sheet. Some mechanical properties were measured at varying angles to the rolling direction to determine the effect of preferred orientation on anisotropy in molybdenum sheet which had been straight, cross, or compression rolled. THE development of the arc-cast process has made available large ingots of molybdenum from which it is possible to roll sheet of considerable size. It is anticipated that such sheet will be further fabricated by spinning, drawing, stamping, or forming. Anisotropy of physical properties caused by the preferred orientation developed in the sheet during rolling may be expected to affect the behavior of the metal when subjected to these fabricating operations. To produce a sheet which will be most amenable to the fabrication of a given shape by a particular operation, consideration should be given to the directions and magnitudes of plastic deformations produced in the operation. When possible, the rolling schedule should be controlled to develop a texture which favors the required deformation. The existence of preferred orientations in rolled molybdenum sheet has been reported by Jeffries,' Konobejewsky,' Fujiwara," Goss,' and Ransley and Rooksby." None of these investigators obtained sufficient X-ray data to permit the construction of pole figures; instead, they based their conclusions upon Debye-Scherrer patterns of a limited number of positions. Ransley and Rooksby devoted some attention to transcrystalline cleavage at 45" to the rolling direction, indicating that it is appreciable in polycrystalline material only when the crystals are in the ideally preferred condition, and that this condition is only approached if the metal has been rolled successively in two perpendicular directions. In a recent paper, Custers and Riemersmao introduced the first pole figures to describe the textures of straight-rolled and cross-rolled molybdenum sheet. To increase the knowledge concerning the generation and effects of preferred orientations in molybdenum sheet, an investigation was undertaken to determine the effects of variations in rolling schedule and annealing treatments on preferred orientation, and to correlate preferred orientations with some mechanical properties. The orientations of straight-rolled, cross-rolled, and compression-rolled sheet have been determined by X-ray analysis, both as-rolled and after recrystallization. Pole figures have been constructed to describe the textures produced by these various rolling procedures. Texture of Cast Molybdenum Ingots In the arc-cast process, molybdenum powder is pressed into a vertical column which is sintered to increase its strength as it proceeds downward into a water-cooled mold, where the metal is melted in an alternating-current arc established between the end of the formed powder electrode and the metal bath at the top of the growing ingot. Since the solid-liquid interface moves continuously upward in the mold, the crystal axes are not normal to the cold surface of the mold but have the curvature shown in Fig. la. X-ray analysis reveals that the cube axis is the fiber axis and that it is normal to the cold surface of the mold; that is, the [loo] direction is parallel to the longitudinal axis of the ingot. This substantiates recent work by

Jan 1, 1953

By J. Chipman, N. J. Grant, H. L. Bishop

Lime and dicalcium-silicate crucibles were equilibrated with molten iron and liquid slags containing iron oxide and small amounts of sulfur. The oxygen content of metal, iron oxide activities, and desulfurization values of the slags were determined in the temperature range 1530 to 1700°C. The influence of magnesia in the slag and the temperature dependence of the solubility of lime in liquid iron oxide and the ferric oxide content were established. The temperature contour of the liquidus surface of iron-silicate slags saturated with lime and dicalcium silicate was also established at 1600°C. THE importance of the role that slag composition plays in the refining of steel has been known for many years. Numerous studies have been made using actual plant data in order to establish the relationship between the composition of the slag and metal during the refining of a heat of liquid steel. These results rarely represent equilibrium conditions since completion of the various chemical reactions involved in steelmaking is seldom realized. In order to establish quantitatively the equilibrium conditions existing between the slag and metal, several laboratory studies have been conducted in the past 20 years to determine the reactions important in slag control. These investigations have included studies of simple liquid basic and acid slags as well as more complex slag systems which approach those commonly found during the refining of a heat of steel. Since most of the previous studies of simple basic iron-oxide slags equilibriated with molten iron were made in magnesia crucibles, it was not possible to establish the distribution of sulfur and oxygen between molten iron and slags consisting only of the three essential components, lime, silica, and iron oxide. This investigation was undertaken to establish the equilibrium conditions for simple lime-iron oxide and lime-silica-iron oxide slags. Accordingly, it was expedient to prepare crucibles both of lime and dicalcium silicate to establish the equilibrium conditions between molten iron and iron-oxide slags saturated with the refractory materials and free from other components. The only other studies of the equilibrium between molten iron and lime-saturated slags are those of Fischer and vom Ende, 1, 2 in which the solubility of oxygen was determined in an air atmosphere. The

Jan 1, 1959

J. R. Lane (Metals Research Laboratory, Washington)—A new type of deformation called "kinking" has recently been described. Is there any relation between the "rumpling" described in this paper and "kinking?" D. C. Jillson (author's reply)—Both are manifestations of bending about [210] axis. The difference is one of degree. W. C. Ellis (Bell Telephone Laboratories, New York) —Some observations of deformation in zinc recorded in this paper may be applicable generally to flow in metals. One of these, deformation in torsion without evidence of slip or twinning in the early stages and with startling ease, when the twist is about the hexagonal axis, adds another method of flow to the presently increasing list of mechanisms. This illustrates again that a crystal will utilize any realizable process to flow and relieve stress. The process is not necessarily classical directional slip—& this case, it is rotational slip. The question naturally occurs: Will face-centered cubic metas stressed by twisting about an octahedral axis flow in a similar manner by rotation on an octahedral plane? I would like to ask Dr. Jillson if he has made any experiments or knows of any experiments of this type on face-centered cubic metals? Face-centered cubic metals possibly would behave differently from zinc, since, for one thing, the stacking sequence is different for the two structures. The results of such experiments, however, would be instructive in providing more information about deformation processes. D. C. Jillson—Dr. Roy E. Swift, working in the Hammond Laboratory at Yale, performed a twist test on a single crystal of brass. The work has not been published, and I do not know the crystallographic direction of the axis of the specimen used. Lo-ching Chang (Columbia University, New York)— Observations similar to Figs. 1 and 2 of the paper were obtained by us during the bending and unbending of an orthorhombic Au-Cd alloy.'l This orthorhombic alloy is the product of diffusionless transformation from a single crystal of p Au-Cd alloy (CsC1 structure) containing 47.5 atomic pct Cd on cooling to about 60 "C.62 Referring to the effects of annealing, has the author tried any loilg time high temperature anneal, such as 150 to 200 hr at 40O°C? D. C. Jillson—No. C. Crussard (Ecole des Mines, Paris: France)—I

Jan 1, 1952

By W. A. Forbes

by the combustion of this gas as it reached the air was a familiar sight in the days when open-top furnaces were in vogue. As blast-furnace practice progressed, however, involving the use of hot blast and the development of power from the gas, blast-furnace construction was modified to conserve this gas for heating hot-blast stoves, raising steam under boilers, and various miscellaneous purposes. When the use of blast-furnace gas was extended to the driving of gas engines, the necessity for thoroughly cleaning the gas became apparent., and soon the advantages of also properly cleaning the gas for use in stoves and udder boilers became more fully recognized.

Jan 10, 1913

C. A. HANSEN (communicated appendix*).-Since the above paper was written, tests have been conducted with a view to securing a sounder basis for discussing the effects of temperature on the behavior of the zinc cell. The following data, while making no pretense to great accuracy, are still reasonably close. Cells were operated with the same feed solutions, but at varying temperatures, the latter being controlled by means of immersed steam coils. Current efficiencies obtained indicate that the corrosion rate

Jan 11, 1918

By E. G. Leonardon

The object of this paper is to describe briefly the practical results obtained in several problems of civil engineering by resistivity measurements of the underground. It is intended for the mining engineer, as well as for the construction engineer; the stratigraphical problems discussed are general and frequently are encountered in mining exploration. Resistivity measurements have been used in mining and oil exploration for a number of years.' Their introduction in the field of civil engineering, on the contrary, is rather recent. It was applied for the first time in the spring of 1928 near Littleton, N. H., in the survey of two dam sites for the New England Power Assn.2 Since then, the geophysical firm with which the author is connected has had an opportunity to develop this field of activity, and more than 20 investigations at dam and tunnel sites have been carried out in the United States and Canada. A part of this work has been verified by underground or drilling exploration. This paper deals with but a few of the results, which we are permitted to make public now. The theoretical and technical sides of the processes employed will not be discussed; they have already been described in various technical publications. A few general points will be mentioned, to make clear the practical examples given. Resistivities OF the Rocks The surveys are based on the measurement of the specific resistance of the rocks. This resistivity is the electrical resistance of a cylinder of

Jan 1, 1932

By Eli T. Conner

My connection, under a commission from the Councils and Board of School Control of the city of Scranton, Pa., with a recent investigation of mine-caves and the resultant damages to surface-improvements, has led to the preparation, at the invitation of our Secretary, of the present paper. It is notorious that there are, in the anthracite-fields, frequent subsidences of the surface, due to the removal of the coal beneath. No particular attention is paid to such occurrences, unless they happen to injure surface-improvements. Many caves have happened in Scranton and its viciuity, which hare excited but little remark, since they have generally caused no serious damage. In August, 1909, a cave occurred in the Hyde Park section of the city, generally known as the West Side, which nearly destroyed school-house No. 16 and considerable adjacent property. Fortunately, there were no pupils in the building at the time; but the thought of the possible result, had the usual number of pupils and teachers been present, aroused the public to the gravity of the situation; and the School Board employed engineers to investigate the case. Two reports were made by separate sets of engineers, which differed in some particulars. These differences were pointed out in the public press and magnified, and the consequent agitation of the subject was taken up and greatly exaggerated by some of the metropolitan newspapers, giving to uninformed people the very erroneous impression that the whole city of Scranton was in danger of sinking into the bowels of the earth. All this tended to affect the credit of the city and to depress real-estate values. The matter was considered at a joint meeting of the Board of Trade, the Councils, and the School Board. The Hon. J. Ben. Dimmick, a former Mayor, suggested that it

Jan 1, 1912

By Harry L. Washburn, Robert L. Llewellyn, W. J. Halvorsen

Many of the problems that occur in the preparation plant originate from practices in the mine. Impurities in raw coal can be in the seam itself or from extraneous material taken in mining from the roof or bottom. In the case of underground mines, the choice of mining equipment will affect the size consist and the amount of extraneous material included with the coal. Also, governmental regulations concerning the degree of rock dusting, gobbing underground, and cleanup have increased the dirt in raw coal. Sulfur dioxide emission standards, on the other hand, are pressuring the coal industry to clean coal more thoroughly. Coal supplied for coking purposes is nearly all upgraded by washing, while for the largest market, electric power generation, a high proportion is shipped as a raw product with processing, in whole or in part, only necessary when excess impurities are mined with the coal. This chapter will deal primarily with plants that process or wash coal to some extent (Fig. 1) and only incidentally with mines shipping raw run-of-mine coal crushed to a top size of, usually, 51 to 102 mm (2 to 4 in.), with little, if any, other treatment. JUSTIFICATION FOR COAL PREPARATION During the past decade, major changes have occurred affecting the market, profit, and long-range planning of the coal industry. Mining companies have become "partners" with consumers at many new and some old mines, both for steam and metallurgical coals. Coal properties have become "assigned" tonnages at mutually agreed upon conditions and prices. Lower unit-train tariffs have been instrumental in helping coal markets to compete against oil and nuclear energy. Coal prices for power plants are still on a Btu (British thermal unit)

Jan 1, 1981

By A. D. Fernie

Growing interest in pit crushing and conveying is evident from the recent many articles, technical papers, and new equipment development. Application of a pit crushing and conveying system is complex. Many factors, such as mine design, production scheduling, as well as initial and ongoing capital and operating costs must be thoroughly and realistically examined. This paper will address the fundamentals to be considered and review several approaches to developing a total system for a new and existing mine situation. The planning function will be outlined and operating and design criteria defined to interface the mining operation and the pit crushing conveying system.

Jan 1, 1986

By J. A. Roberson, Robert A. Rapp

From the observation of platinum wire marker movement in the oxidation of columbium at high lemperatures and low oxygen pressures, predonzinant cation diffusion in CbO, has been demonstrated. The Cu,0 molecule was used as an oxidizing species to study the nature of the porous scale and the location of the reduction site in the oxidation of colum-bium. The Cb205 scale contains microporosity and forms by alternate ionic diffusional growth and fracture. The oxidation of columbium at high temperatures and very low po, results in a relatively compact and protective Cb205 layer. THE observation of marker movements during oxidation is one means for the identification of the mobile ionic species in an oxide lattice. Previous marker experiments in the oxidation of columbium have all resulted in the markers being found on the outside surface of the Cbz05 scale. The Cr203 powder markers of Klopp et a1.,' the gold film marker of Kofstad and ~jijllesdal,' and the platinum wire marker of Cathcart et a1 .3 were found at the oxide/gas interface for oxidation temperatures ranging from 450" to 120O0C. However, in all experiments relatively high oxygen pressures were used. As discussed by Mrowec, even the interpretation of marker experiments in simple scales containing only one compound is not without ambiguities. In brief, it can be said that a marker may be found almost anywhere in the scale layer if the metal oxidizes by cation diffusion through the scale; the position of the marker depends upon morphological happenings in the scale. When considering marker movement in a polyphase scale one must proceed with extreme caution. For example, in the past (and present) work markers have never been found at the columbium-scale interface, and one might infer that the oxygen ion is mobile in CbO and CbO,. However, only trace quantities of CbO and CbOz have been present on any of the specimens, so no firm statement is justified on this basis. Despite previous experimental work, considerable doubt still exists concerning the role of the oxides CbO and CbOz in the oxidation of columbium. The identification of the mobile ionic species in CbO and CbOz from the observation of platinum wire markers was one goal of the present investigation . The linear kinetics of columbium oxidation at high temperatures (T - 1000°C) suggests that the Cbz05 scales which form on columbium are porous. From mercury absorption measurements on a Cbz05 scale formed at 500"C, Aylmore et al.' reported a minimum volume fraction of connected voids equal to 0.15. While these scales often appear to be quite porous when viewed in metallographic cross section, they are so brittle that metallographic preparation is likely to exaggerate any porosity originally present. In this investigation, porosity developed during the oxidation of pure columbium and present at the high temperature was detected by oxidizing specimens in sealed evacuated capsules containing large compacts of mixed copper and CuzO powders. wooda has demonstrated that the CuzO, or (CuzO),, molecule is volatile and that oxygen is transferred by the CuzO molecule from a Cu/CuzO mixture to materials having a greater affinity for oxygen. For each molecule of CuzO that is reduced at a sink for oxygen, two atoms of copper are deposited. Quantitatively, essentially all of the oxidation carried out by a Cu-Cu20 compact results from a displacement reaction involving the CuzO molecule. When a metal which oxidizes to form a porous scale is exposed to the CuzO vapor, the CUZO molecules are reduced in the pores leaving a deposit of metallic copper to mark the site of the reduction. This technique has the rather unique advantage that any copper-coated pores found in the scale are unambiguously related to the reduction site in the growth of the scale under consideration. Pores or cracks which form in a msition*- external to the reduction site or which occur as a result of cooling or handling of the specimen will not exhibit the copper deposit. EXPERIMENTAL PROCEDURE Marker experiments were made on columbium metal, and on pellets of CbO which had been pressed and sintered. Platinum wire markers (0.001 and

Jan 1, 1968

By James E. York

AT a meeting of the American Society for Testing Materials at Atlantic City, June, 1908, Dr.. C. B. Dudley, in his presidential address,' showed the vital necessity of not only making a steel rail as good as in the past, but of making it considerably better in order to meet the present and prospective require¬ments of railroads. Doctor Dudley requested the co-operation of all who from personal experience could give information that would result in bringing about the production of a steel rail that could be relied upon to meet the present requirements. I have had considerable experience in the practical manufacture of steel of almost every grade, during the past 40 years, and I shall suggest changes that will bring about the results desired. Doctor Dudley has had a long experience as chemical and metallurgical expert for the Pennsylvania railroad, but he frankly admits that up to the present time both he and other metallurgical experts lack the practical knowledge of steel-making that is necessary to state correctly the reasons for the unreliability of the steel rails now produced. The necessity is self-evident for more positive practical knowledge on the part of these experts of what is possible and what is impossible regarding the practical manufacturing of steel rails from the ingot to the, finished product. Chemical knowledge in steel-making is far in advance of what it was years ago, and might be said to cover every requirement (in that department) for producing reliable steel. The study of the metallography of steel has been of great value, also the physical testing of steel, but this knowledge will only de-

May 1, 1909

By J. M. Woodall

GuAs crystals which have been grown in quartz boats by the horizontal Bridgman method in the pvesence of Ga20 vapov have beetz found to have carrier and donor distributions which do not correspound to those expected from simple dopant seg-vegation during directional freezing; Instead, the carrier distribution is determined by the heat-trentnzent history of the crystal, while the donor distribution, zohiclz is principally due to silicon, is fixed by the pozuth rate, the geo)tlet.ry of the crystal growth vessel, and tlze initial Ga20 pressure. WHEN semiconducting materials are made into doped crystals by the normal freezing method,&apos; they usually exhibit doping variations along the growth axis. If a) there is no dopant diffusion in the solid, b) the dopant is distributed uniformly in the melt, and c) the distribution coefficient, k, does not vary with composition, then the doping variation along the growth axis is represented by the equation: where C is the doping level in the solid at a point where a fraction g of the original liquid has frozen, and Co is the mean concentration. When the dopant is either a singly ionized shallow donor or shallow acceptor, C also represents the carrier concentration. Even though this equation accurately describes the dcping profiles of a large number of normal freeze systems, there are several special systems for which Eq. [I] does not apply. One such system is the horizontal Bridgman method for preparing oxygen-grown GaAs crystals using quartz vessels. Several workers2"* have shown that GaAs crystals grown by the horizontal Bridglnan method using quartz vessels are generally contaminated with silicon in concentrations in excess of 5 < 10lG atoms per cu cm. This contamination is ascribed to a reaction: occurring at the walls of the crystal-growth vessel which liberates silicon into the melt and Ga2O vapor. It has been shown4 that this reaction, and, hence, the silicon contamination, can be suppressed by the addition of oxygen to the crystal-growth apparatus. It is the purpose of this paper to describe a special apparatus capable of yielding single crystals of GaAs grown in the presence of oxygen and to describe both the kinetics of silicon suppression in this system and the relationship between the carrier concentration profile and the silicon concentration profile. EXPERIMENTAL-CRYSTAL GROWTH A schematic diagram of the apparatus used in the oxygen addition experiments is shown in Fig. 1. The most important features of this apparatus are: a) the use of a sand blasted quartz boat, h) a quartz rod of length 1, with a hole of cross section A, that is placed near the boat to limit the free space volume V, over the melt during the growth, and c) the temperature gradient at and near the solid-liquid interface. Sand blasting the boat is necessary to prevent wetting of the melt. The quartz rod retards the diffusion of the GazO vapor away from the melt to the colder portions of the ampoule. A crystal is prepared by first loading a 5.5-in. boat, which has been cleaned in aqua regia, with 40 g of 99.9999 pct Ga along with 1 to 8 mg of Ga203 powder. GazO3 is a convenient source of oxygen since it reacts with gallium at the melt temperature to form Ga20 vapor, the species which apparently controls the suppression of silicon contamination. The loaded boat, the quartz rod, and the 99.9999 pct As are placed in the ampoule as shown in Fig. 1. Generally, GaAs seeds were not used since most of the unseeded growths resulted in monocrys-tals. The ampoule is evacuated to 10-5 Torr and sealed off. The GaAs melt is synthesized by placing the ampoule into a two-zone horizontal Bridgman furnace. The two zones are separated by several sandwiched layers of -in. Fibre-Fax board drilled with holes slightly larger than the OD of the ampoule. This causes a very large temperature gradient between the two zones, which is necessary for single-crystal growth. The two-zone furnace is mounted on a stand fitted with a roller bearing which allows uniform motion of the furnace in a horizontal direction. A uniform velocity of the stand is achieved by the use of a windlass device which winds up a wire attached to the stand. Movement of the solid-liquid interface is accomplished by fixing the position of the ampoule and moving the stand. Growth rates investigated in this experiment were between 0.4 and 1.2 in. per hr. The composition of the melt is fixed by maintaining an arsenic reservoir at 618°C. The stand is moved away

Jan 1, 1968

By Henry Mulryan

THE largest and purest known deposit of diatomite is being actively mined and processed 3 ½ miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Manville Products Corporation. The workings FIG. 1-LOCATION OF DIATOMITE DEPOSIT AT LOMPOC. cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoc, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1936

By F. O. Garrabrant

Power is furnished to the Climax Molybdenum Co. by the Public Service Co. of Colorado over two 100,000-volt lines to a bank of three 3333-kva. transformers 100/13.8 kv. These transformers are so designed that with the addition of forced cooling their capacity may be increased 33? per cent at 12,000-ft. altitude. Under present conditions, these transformers are operated at 140 Per cent of their rating with forced air cooling. On the secondary side of this bank there is a 15-kv., 1200-amp. Westinghouse oil circuit breaker provided with automatic reclosing relays allowing three successive short circuits before lockout. From this breaker 13.8-kv. power is transmitted to a central switching station (Fig. I) where all circuits radiate to the different operations of the property. Each circuit is protected by a 23-kv., 600-amp. oil circuit breaker with by-pass and isolating disconnecting switches. Mine Power at 13.8 kv. enters the mine through a ventilation raise over a three-conductor, size 1-0 varnished cambric insulated, leaded, steel-wire armored cable, insulated from 17 kv. This power is received and distributed through one switching station and four underground substations, shown in Fig. 2. No. 370 substation (Fig. 3) contains three a 13,800/440-volt, single- phase Pyranol transformers protected on the high-voltage side by a 600-amp. manually operated oil circuit breaker. This station serves 20 slusher-hoist motors, a 45-kw., three-phase, 220-volt electric furnace, a Massco hot miller for tempering and milling Timken detachable bits and a hoist with 175-hp motor on the No, 3 development shaft. Also at this shaft are three pumps. One two-stage pump, 1200 gal, per min., 500-ft. head, 3600 r.p.m., driven by a 150-hp. motor, is at the bottom of the shaft, Two deep-well pumps, 500 gal. per min., 500-ft. head, are at the collar of the shaft. under normal operation the one pumping 1200 gal. per min, is controlled by a float switch to take care of the water. If this pump fails, or if its capacity is insufficient, the first 500-gal. pump is automatically started1 and if still more capacity is needed the second 500-gal. pump automatically starts. Time delay relays are provided on the deep-well pumps, so that if power fails the column will have time to drain before the Pumps restart. On failure of any Of these, an alarm is sounded in the train dispatcher&apos;s office, so that mechanics can be sent to ascertain the cause of failure and make repairs. The cable from No. 37&apos; substation is run to the switching station, in which are four 15-kv., 600-amp. direct-current sole-noid-operated oil circuit breakers. The current for Operating and tripping is furnished by a 125-volt storage battery. All breakers are operated from the switchboard in the compressor room. One circuit from this switching station goes to the

Jan 1, 1946

By Zay Jeffries

HOSTILITIES in Europe, Asia, and northern Africa were responsible for dislocations in rare-metal supplies during 1940. Although the consumption of some of the rare metals is small the dislocations may be relatively large. In some cases these are advantageous to North America and in others they are disadvantageous. Specific instances will be cited later. Barium T HIN films of barium metal on special steel balls greatly improve the life and reduce the friction of rotating anodes in highly evacuated small X-ray tubes and make possible the operation of these anodes at relatively high temperatures. These remarkable results are described in an article by Atlee, Wilson, and Filmer in the Journal of Applied Physics for September, 1940. Oil could not be used because of the high temperatures on the one hand and its volatility on the other. Fig. 3 shows diagramatically the rotating anode and the method of coating the steel balls with barium. The letters K.I.C. refer to "Kemet Iron Clad." The K.I.C. wire was mounted so that the barium could be evaporated by direct passage of the electric current. At high temperatures the barium dif-

Jan 1, 1941

By Robert S. Archer

THE proper material of construction for a given purpose is that material which meets the requirements satisfactorily at the lowest ultirnatc cost. It is consistent with this principle that most aluminum castings are made of an alloy containing about 8 per cent. copper. This alloy possesses mechanical properties satisfactory for general engineering purposes together with manufacturing characteristics leading to the production of finished castings at low cost. It is to the aluminum industry what gray iron is to the iron and steel industry. Just as some services require "semi-steel," malleable castings or steel castings instead of gray iron, there is a certain and growing demand for aluminum castings of superior strength or ductility, or both. Since the beginning of .the industry producers and others have sought to develop alloys or processes by which such castings could be made. Out of these efforts have emerged many alloy compositions and special processes, of which only a few have had sufficient merit to survive. It is the purpose of this paper to describe those which seem to the authors to offer the greatest promise for the production on a commercial scale of aluminum castings of superior mechanical properties, with special reference to heat-treated castings. The suitability of an alloy or process for actual manufacture is affected by so many factors that the problem of appraisal is not a simple one. Since this is such an important part of the whole subject it is proposed to discuss briefly some of the requirements. The final verdict is of course the result of commercial trial and experience. It will therefore, perhaps, be profitable to employ a somewhat historical method of treatment in discussing the subject of alloy development. The alloys or processes to be used in the production of aluminum castings are to be considered from the standpoint of their effects on both the utility and the cost of the finished casting. Specific gravity and mechanical properties come under the first head, while the properties

Jan 1, 1927