Search Documents

By J. B. Campbell, V. V. Valleroy, B. T. Willman, L. W. Powers

A steam drive of heavy oil was field tested in a shallow, low oil-saturation formation near Deerfield, Mo. The pilot was conducted in the Warner formation, a sandstone containing an 18' API oil having 1,000-cp viscosity at the 60F origind reservoir temperature. The formation war at a depth of 160 ft. Steam was injected into nine input wells arranged in an array of inverted five-spot patterns. In the completely confined center pattern, 14 temperature observation wells were installed to obtain thermal data and observe test progress. Late in the test, slugs of ammonia were injected to trace the flow paths of injected fluids. From the test area about 7,000 bbl of oil were produced. Data were obtained on areal and vertical temperature distribution, steam front advance, reservoir fluid movement and terminal saturations. This field test of a steam drive (I) demonstrated the feasibility of the method, (2) confirmed that the low residual oil saturations observed in the laboratory are obtained in the steam-swept region in the field and (3) provided recovery and conformance data for one set of field conditions. INTRODUCTION The Deerfield steam drive pilot test was conducted in a shallow sandstone containing 1,000-cp oil. The venture was undertaken cooperatively by the research and production departments of Carter Oil Co., which organizations have since been consolidated into Esso Production Research Co. and Humble Oil & Refining Co.. respectively. The production department was interested in steam injection at Deerfield because it appeared to be the most promising method of commercially producing this heavy oil deposit. The research department was interested in applying the new recovery method and in evaluating its performance in the field. At the time the test was begun, the initial oil saturation was not well known. Subsequent air coring and early pilot results confirmed that there was too little oil in place for profitable commercial exploitation by steam. Pilot termination at that time, however, would have been premature for evaluating field performance of the process, and the tert was continued to obtain additional data on steam injection as a recovery method. The test was located in Vernon County, Mo., about 10 miles north of the town of Deerfield and only a few miles from the Kansas border. The pilot site was selected as typical of the area. The location represented neither the highest nor the lowest oil saturation region in the acreage under lease in 1954. The steam drive was conducted in the Warner sandstone of Lower Pennsylvanian age. At the test site the top of the Warner occurs at about 160 ft subsurface and the formation is a fine- to medium-grained micaceous sandstone that dips gently to the northwest at the rate of 12 to 15 ft/ mile. A cross-section and permeability profile of the test location are shown in Fig. 1. At the pilot location the average total thickness of the Warner formation is about 43 ft, but the effective thickness for steam drive is 26 ft. Two distinct types of hydrocarbon saturation are apparent. The lower portion of the total sand, averaging about 17 ft thick, contains a very heavy asphaltic material that will not flow under the influence of a steam drive. This bottom interval, referred to as a dead oil residue, was not considered as part of the net sand undergoing steam exploitation. The initial formation and fluid properties of the upper 26 ft in the test area are summarized in Table 1, and variation of oil viscosity with temperature is shown in Fig. 2. Imbibition tests on preserved core samples taken at the end of the pilot test showed that the Warner sandstone was then neutral or slightly water-wet. Initially, the reservoir may have been strongly water-wet as indicated by low relative permeability to water during both water injection testing and early steam injection. PRIOR HISTORY Initial production tests of wells at the pilot site produced water with only a faint show of oil. No gas was produced except at Well 7-W in the pilot area and at another well about 1/3 mile northeast of the pilot. Prior to the start of the steam drive, a two-well water injection test and a two-well air injection test were conducted. No oil was produced by either. Water was pumped into Well I-W in the northeast corner of the pilot area with simultaneous production from Well 1 (Fig. 3). The air-injection tat was run at input Well 9-W and its offset, Well 2, in the southwest corner. Air and water injectivities were about the same when corrected for viscosity and pressure differences.

By W. Vickers

SALKOVITZ1 has given a number of useful angles between planes for use with the Laue method in determining the orientation of bismuth single crystals. Bismuth is usually considered as having a face-centered-rhombohedra1 structure with its axial angle 87°34', Fig. 1. A similar figure given by Sal-kovitz appears to be in error in that the angle there marked as 87°34' should be 92°26. The primitive cell is a single rhombohedron of axial angle 570 14. The structure is almost face-centered-cubic and hence high accuracy in measurements is essential if there is to be no confusion in indexing poles or zone axes. It is easier to get this accuracy if zone axes are plotted on the stereogram because they will lie near the basic circle where the net has a more open scale. The zone axes can be read from the film, using a Greninger chart, and can be plotted more accurately than poles. Also, the angles between points near the basic circle can be read more accurately than those between poles near the center. In order to use the zone axes the angles between directions have been calculated from a formula given by Niggli,2 and are given in Table I. Miller indices

Jan 1, 1958

By T. C. Craig

For the year 1934, there were 382 oi1 wells completed for a total initial of 146,965 bbl. Fifty-three wells were deepened for a total increase of 8363 bbl., bringing the total volume of new oil to 155,328 bbl. As of Jan. 1, 1934, the daily potential of the field as determined by the Texas Railroad Commission was 159,740 bbl. Of this amount 26,429 bbl. is "marginal oil," and 2682 bbl. is exempt on account of water. In December, 1934, the daily potential was established by the Railroad Commission as being 297,501 bbl. with a daily allowable of 56,800 bbl. Of this amount 31,993 bbl. is "marginal oil," and 2183 bbl. is exempt on account of water. There has been no field-wide test made during the year, and as a result the rated potential of the field is in all probability much higher than the actual potential. As each new well comes in, a five-day test is made under the supervision of the Railroad Commission. The potential thus established is added to the field potential and shares its pro rata part of the market outlet, which is the allowable production, no allowance

Jan 1, 1935

Upon the recommendation of its Technical Committee, The Com-pressed Air Society has adopted the following definitions of, certain terms. Displacement.-The displacement of an air compressor is the volume displaced by the net area of the compressor piston. Capacity.-The capacity should be expressed in cubic feet per minute, and is the actual amount of air compressed and delivered, expressed in terms of free air at intake temperature and at the pressure of dry air at the suction. Volumetric Efficiency.-Volumetric efficiency is the ratio of the capacity to the displacement of the compressor, all as defined above. Compression Efficiency.-Compression efficiency is the ratio of the work required to compress isothermally all the air delivered by an air compressor to the work actually clone within the compressor cylinder, as shown by indicator cards, and may he expressed is the product of the volumetric efficiency (the intake pressure and the hyperbolic logarithm of the ratio of compression), all divided by the indicated mean effective pressure within the air cylinder or cylinders.

Jan 8, 1918

BUMPS in No. 2 Mine, Springhill, N. S., furnished the main feature for discussion at the morning meeting* on Ground Movement and Subsidence on Feb. 18. Walter Herd, the author of the paper by which the discussion was introduced, not being well, was unable to be present. The paper was presented by T. L. McCall, who laid stress on the presence of sand- stone as the cause of bumps, on the value of retreating longwall in eliminating such phenomena at the coal face and on the advantage of wide headings with packs on either side, leaving space behind them for any coal that bumps might dislodge. George S. Rice, who presided, referred to his visits to the Nova Scotia mines and said that bumps usually occurred only where the coal was thick and strong and the roof and floor both more than usually hard. If any of the three were weak, bumps were not likely to occur. In the Nova Scotia mine, to which Mr. Herd referred, there was no material for packwalls and for this reason as well as for safety he had been convinced that long- wall retreating with a small percentage of pack walling was the most feasible plan.

Jan 1, 1929

By J. Handin, S. J. Bauer, M. Friedman

Deformation mechanisms in room-dry and water-saturated specimens of Charcoal Granodiorite, shortened at 10-4s-1, at effective pressures (Pe) to 100 MPa and temperatures to partial melting (?1050°C) are documented with a view toward providing criteria to recognize and characterize the deformation for geological and engineering applications. Above 800°C strength decreases dramatically at effective pressures ? 50 MPa and water-weakening reduces strength an additional 30 to 40% at Pe = 100 MPa. Strains at failure are only 0.1 to 2.2 percent with macroscopic ductility (within this range) increasing as the effective pressures are increased and in wet versus dry tests. Shattering (multiple faulting) gives way to faulting along a single zone to failure without macroscopic faulting as ductility increases. Microscopically, cataclasis (extension microfracturing and thermal cracking with rigid-body motions) predominates at all conditions. Dislocation gliding contributes little to the strain. Precursive extension microfractures coalesce to produce the throughgoing faults with gouge zones exhibiting possible Riedel shears. Incipient melting, particularly in wet tests, produces a distinctive texture along feldspar grain boundaries that suggests a grain-boundary-softening effect contributes to the weakening. In addition, it is demonstrated that the presence of water does not lead to more microfractures, but to a reduction in the stresses required to initiate and propagate them.

Jan 1, 1982

By Ray Hammond Misener

THE purpose of this paper is to describe the installation of the pumping station on the 3314-ft. level of the Carlos Francisco mine of the Sociedad Minera Backus y Johnston del Peru, at Casapalca, Peru. However, so much preliminary work was necessary before the actual installation could be started that some of that work will be described briefly, in order to clarify the discussion of the main subject. The Sociedad Minera Backus y Johnston del Peru, a subsidiary of the Cerro de Pasco Copper Corporation, owns and operates a group of mines in the Casapalca district, of which the most important are the Carlos Francisco and the Aguas Calientes. These two mines, one mile apart, are connected on their 2100 and 2700-ft. levels. These are motor-haulage levels, equipped with 3 ½ -ton Baldwin-Westinghouse locomotives operating from a 260-volt d.c. overhead trolley. A 38-cu. ft. hopper-bottom car is used. Each mine has a 2 ½ -compartment, inclined (70°) winze shaft. The Aguas Calientes shaft, operating between its 2100 and 2900-ft. levels, is used only for men and materials; whereas the Carlos Francisco shaft, between the 1700 and 2700-ft. levels of that mine, is the main operating shaft for the district. All the ore from the Carlos Francisco and the Aguas Calientes mines is hoisted through the Carlos Francisco shaft. The ore produced in these mines is by-passed to the 2700-ft. level, where it is gathered by the electric trains, taken to the Carlos Francisco shaft and dumped into an ore pocket in front of the shaft. The ore is hoisted to the 1700-ft. level in 2-ton self-dumping skips and emptied into a 150-ton loading pocket. There it is loaded into electric trains and despatched to the concentrator through the Backus and Johnston tunnel, which is the main entry from Casapalca to all the mines in the Backus and Johnston group. DEVELOPMENT PROGRAM In 1934 the following development program was outlined for the Carlos Francisco and the Aguas Calientes mines: (1) to deepen the Carlos Francisco shaft from the 2700 to the 3400-ft. level, (2) to deepen the Aguas Calientes shaft from the 2900 to the 3300-ft. level, and (3) to connect the two shafts on the 3300-ft. level with a motor-haulage crosscut. Each mine was to be developed also on intermediate levels (2900 and 3100). The three levels were to be spaced 54 meters (177 ft.) floor to floor, measuring from the 2700-ft. level along the incline of the shaft. The Carlos Francisco mine, together with the section between it and the Aguas Calientes mine, produces 10,000 gal. of water per minute. A fault to the north

Jan 1, 1943

By Berlen Moneymaker

THE development, within recent years, of core drills capable of drilling holes up to 72 in., or even more, in diameter, has made possible an entirely new and valuable method of geologic exploration, Although little used until recently as an exploratory tool except in the United States, by the Tennessee Valley Authority and the Corps of Engineers of the U. S. Army, for the exploration of damsites, the large-diameter core drill may be used to good advantage in other types of geologic exploration. Its princi-pal utility is that of supplementing, rather than replacing, other means of exploration. Although core is frequently recovered intact, the greatest advantage of large-diameter drilling is that the holes produced are large enough to be entered by the geologist and engineer, and thus afford an excellent means of examining undisturbed rock. The walls of the holes are smoothly cut, and in some rocks nearly or quite polished, so that the most minute details of structure and stratigraphy are clearly disclosed. Such features as faults, joints, bedding planes, weathered "seams," and beds or layers of soft materials, which are not always amenable to disclosure by cores recovered from small-diameter holes, are conspicuously displayed in the walls of large holes. Frequent reference to the drilling of large-diameter holes is made in engineering literature, but comparatively little emphasis has been placed on their value in geologic investigation. It is, therefore, intended that the present paper acquaint the geologist, as well as the engineer, with the large-diameter core drill and the technique involved in its use, and also with its advantages, disadvantages and limitations as an implement of geologic exploration.

Jan 1, 1938

By WILFRED SYKES

IT is with particular pleasure that I welcome the members of the Open-hearth Conference of the I American Institute of Mining and Metallurgical Engineers to this meeting, as I feel this is one of the most useful activities of the Institute in the field of ferrous metallurgy. For the information of our other members I might say the Open-hearth Conference was organized by Mr. Reynders when he was president, and is made up of open-hearth superintendents and metallurgists. All the plants are invited to send representatives, and practically all do, with the exception of the U. S. Steel Corporation. It meets twice a year to discuss various problems in connection with the manufacture of steel, and its minutes are published for the benefit of those attending, the expense being defrayed by the participating companies. This conference, .1 believe, should be a model for activities in the other branches of the work covered by this Institute. It works, not by reading formal papers, which we all know is not a very satisfactory method to bring out the experience of others, but rather by a round-table method of discussion. The spirit of the meetings is such that each member feels perfectly free to state his experience, and he gets as much as he gives. A series of topics for, discussion is brought to the attention of the chairman and after one is exhausted the next point is taken up. In this way there is a real interchange of ideas and experiences which cannot fail l to be of the greatest benefit to those attending. That these meetings are beneficial is evidenced by the "continued growing attendance and lively discussions at these half-yearly meetings.

Jan 1, 1930

By O. W. Shimer, D. C. Helms, C. E. Brown

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90° and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness and pitch of the beds.

Jan 1, 1946

By O. W. Shimer, D. C. Helms, C. E. Brown

The early history and progress of anthracite stripping, from the first known operation at Summit Hill in 1821 through 1917, was covered in 1917 in a paper by J. B. Warriner,1 then chief engineer, now president of the Lehigh Navigation Coal Co., and stripping methods between 1917 and 1931 were the subject of a paper in 1931 by H. H. Otto,2 of the Hudson Coal Company. . The present paper is confined to methods used today on pitching beds in the western middle and southern anthracite fields. The anthracite industry, not unlike other large industries, had been affected for more than a decade by the adverse economic conditions of the country. High development and operating costs and the competition of other fuels caused some collieries to be closed temporarily, while others were permanently abandoned. In order to obtain a larger tonnage at a lower development cost, a larger stripping program was put into effect by many companies. In 1932, stripping operations accounted for 3½ million tons, or 7 per cent of the total anthracite production of the year, and in the next 10 years this increased until more than double that amount, or over 14 per cent of the total production, was from stripping operations. These figures represent the total production of the entire anthracite region; unfortunately, the figures have not been separated from the different fields. There are some operations in the southern and middle western fields where the tonnage obtained from stripping amounts to more than 30 per cent of the total colliery production. Stripping operations on pitching beds present difficult problems. Owing to the various geological formations, a different situation is encountered in nearly every stripping pit; and because of the proximity of an overlying bed, it is very often necessary to load the entire overburden into trucks and haul it out of the pit to the dump area, although back filling and casting is done whenever possible. Beds in the areas described in this paper pitch from 20" to 90 and some are on the invert in many sharp folds and faults. Planning The more successful strippings have had adequate engineering analysis. Some work is being done without much preliminary planning, but many strippings would have failed completely if close supervision by the engineering department had not been . maintained. Locations of stripping areas are determined as follows: I. By constructing cross sections over the areas and drilling sufficient diamond-drill or well drill holes to study the strata and to determine the location, thickness

Jan 1, 1944

. F. W. SPERR, JR.,* Pittsburgh, Pa.--Mr. Malcolmson states that the Carbocoal process produces ammonium sulfate in excess of that normally recovered in the ordinary byproduct coke process. Table 3 indicates that 20,000 to 25,000 lb. of sulfate of ammonia are obtained in carbonizing 1000 tons of Clinchfield coal. This is a high-grade coal and yields from 26 to 28 lb. of ammonium sulfate per ton in a modern byproduct coke oven. On the next page, 21 lb. is stated as the yield of ammonium sulfate per short ton of raw coal; this is less than the average production from any well operated byproduct coke-oven plant treating coal of the character usually coked, in Pennsylvania and Ohio. The statement as to the comparative yields of light oil is somewhat misleading in view of the results obtained during the past year or two by the more modern byproduct coke plants. The plants put in operation by the H. Koppers Co., during the past two years, are producing about 3.5 gal. of light oil per short ton of coal, and several of these plants are producing more than 4 gal. per ton. The yield of pure toluene runs from 0.45 gal. to 0.55 gal. per ton. .The quality of the light oil .obtained from the Carbocoal process is of much greater importance than would be inferred by one not closely familiar with the subject. The presence of paraffins in the benzol and toluol fractions seriously detracts from their commercial value; the benzol and toluol fractions derived fro in the Carbocoal process contain about 50 per cent, of paraffins. It should be thoroughly understood what these paraffins are. They are simply hydrocarbons that go to make up ordinary petroleum, and if a successful method for the removal of paraffins from benzol and toluol has been developed, this can at once be applied to several well known processes by which benzol and toluol can be made directly from petroleum, which have as yet been total failures on account of the contamination of these products by paraffins.

Jan 11, 1918

By D. W. Loucks

There is plenty of evidence to indicate that at least one of man's chief interests in life is to make himself as comfortable as possible. If you doubt this, just watch the fellow next to you for the next half hour trying to find the most comfortable position that a hard chair has to offer. Comfort, however, does not always mean an easy chair. To some, it may mean a wealth of money: to another, freedom from worry. But to most of us, it means first of all a comfortable atmosphere in which to live, and to a great many of us it probably also means freedom from that annoying task of firing the furnace. Today more than ever before, automatic heat is one improvement that is placed high on everyone's list. Perhaps this is because automatic heating is becoming relatively cheaper. Perhaps it is because of a good publicity campaign on the part of the oil and gas men or maybe it is just that we are getting lazier day by day. At any rate, almost every issue of Better Homes and Gardens, House Beautiful, or your other favorite home magazine carries an article extolling the virtues of this or that automatic heating system.

Jan 1, 1949

By Victor A. Phillips

A series of specimens of a Cu- 3.23 pct Co alloy were prepared with particle diameters from zero to 590A. The samples were then cold-rolled 95 pct and the effects of the particle size on the behavior on annealing for hr at temperatures between 100" and 900°C were studied (by hardness, light, and electron metallography). Particles, particularly for d r 105 to 590A, greatly impeded softening and vecvystallizn-tion, and tended to give elongated grains. Particles deformed fairly homogeneously with the ,matrix, be- IN a previous study by the author,' the growth of cobalt-rich precipitates was followed electron microscopically in Cu-3.12 Co alloy as a function of aging, typically at 650°C. The coherent spherical precipitates grew to 520 + lOOA average diam before spontaneously losing coherency and developing (111) facets. Stretching a few percent after precipitation 2aused loss of coherency to occur sooner at about 220A average particle diam. The particles apparently retained their fcc structure after loss of coherency. coming lau2ellae. For d = 55 to 180A, these lamellae gave streak-contrast effects apparently due to coherency strains , and spheroidized on annealing at 600" to 650°C, forming coherent particles. Particles of d = 250 ov 320A lost coherency during t-olling, giving incoherent lamellae. Recrystallization apparently occured by growth of new grains into unrecrystallized (recovered) material at temperatures below that at which cobalt atoms had much mobility. The present study was undertaken to explore the effect of cobalt-rjch particles of various average sizes from 50 to 600A diam on the isochronal annealing behavior of copper after heavy cold rolling. The previous work' was used as a guide in preparing the two-phase series of prerolling structures. The solution-treated alloy was also rolled for comparison. A further question of interest in the present study was whether dislocation and particle hardening were additive, since the prerolling structures covered the full range unaged - peak aged — overaged, and further precipitation might occur on annealing after cold rolling. Although there have been exhaustive studies of the isothermal2"6 and is~chronal annealing behavior of

Jan 1, 1967

By E. H. Rose

IN a year of sober reflection and stocktaking after the mineral-squandering spree of World War II, the role that beneficiation of low-grade must henceforth play in American mineral industry has become unmistakable. From the volume of research and development progress in mineral engineering during 1946, mineral dressers evidently have ample resoluteness to meet the challenge. Perhaps ,the most conspicuous trend of the year was the renascence of interest in gravity concentrating methods and more serious effort than ever before to make them effective in finer size ranges down to 200 mesh. This has been forced by the problem in iron ores where the low value of the product will not support a high flotation reagent cost, however good flotation pilot plant results may have been and however well the acute problem of variable feed may be met. The race is on between rabbit flotation and tortoise gravity methods and a surprising amount of betting money is being laid on the tortoise which already is showing previously unsuspected talent for speed. Mostly, however, a wait-and-see attitude prevails during the present preliminary heats. As evidence of the latter, two magnetic plants are now on the boards for magnetic taconites on the eastern Mesabi to establish a reprieve against the time when nonmagnetic taconites must be addressed. Incidentally, these operations will force the blast-furnace issue on preparation of fine material since a minus-100-mesh grind is contemplated.

Jan 1, 1947

By W. D. B. Motter

DURING the early development of blasting with liquid oxygen explosives the trend of experimentation was towards increasing the effectiveness of the explosive. Its characteristic of becoming inert after evaporation of the oxygen content made a strong appeal from the standpoint of safety, especially with missed holes. It later became apparent, however, with practical use of this explosive, that LOX lacked certain other safety characteristics. As its effectiveness was increased, it became more subject to detonation by impact. The object of this paper is to show the steps taken by one operating company to achieve greater safety in the large-scale handling of liquid oxygen explosives.

Jan 1, 1933

By H. NORTON JOHNSON

THE oil industry in California during 1929 reached new heights and new depths in the discovery and development of the oil resources of the State. The discovery of new fields, and more especially the discovery and development of deeper prolific sands in known fields has, for the first time in its history, brought the potential production of completed wells within the State to over 1,000,000 bbl. oil per day. Constant improvement in equipment and technique has made possible economic development to depths unheard of but a few short years ago. Commercial production from a depth of over 4000 ft. was considered quite an accomplishment in 1923 when the Meyer sand at Santa Fe Springs was developed, and when later oil was successfully raised from this depth.

Jan 1, 1930

By J. HUNER

Twenty-four new fields were found in Louisiana during 1945. Of this number 15 were oil fields, eight were gas condensate, and one a dry gas field. None of these fields, with the exception of West Delhi, is as yet of any great consequence. The Weeks Island field in Iberia Parish may eventually develop into a considerable reserve.

Jan 1, 1946

By Carl Scholz

Discussion of the paper of Carl Scholz, published in Bi-monthly Bulletin, No. 22, July, 1908, pp. 551 to 559. HOWARD N. EAVENSON, Gary, W. Va. (communication to the Secretary*) :-For some time before the publication of Mr. Scholz's paper, I had been collecting data bearing upon its subject, and I now take pleasure in presenting my results to the Institute in the form of a discussion. It has long been a matter of common opinion among mining-men that mice-explosions are, more frequent during the colder, or winter months, than during the warmer ones, and it is a matter of common knowledge among them that the air-ways and road-ways in most mines are much drier and are more in¬clined to be dusty during the winter than during the summer. In many mines, places which are wet and sloppy in the summer are dry and sometimes dusty during the winter. These changes, of course, can only be due to atmospheric conditions, and are caused by differences in temperature and humidity. Until recently, however, very little attention has been paid to the part that atmospheric conditions may play in mine-explosions, or, rather, to the effect they may have in rendering mine-conditions peculiarly dangerous, and in spreading and rendering more disastrous the effects of what would otherwise probably have been .small explosions. To show the difference in mine-conditions during sunnier .and winter months, I have tabulated in Table I. the results of 24 observations of hygrometric conditions in several different mines at different times of the year. Mines Nos. 1, 2, and 6 are located in the Pocahontas.coal -region, in McDowell couuty, W.Va., the first one being a shaft-mine shaft mine and the others drift. Mines 1A and 2A are drift-mines located in Logan county, W. Va. All of these are mines of fair size, but none of them has been in operation more than six years,

Jun 1, 1909

By William M. Bowron

THIRTY years ago, when I stood on the cliff of red fossil iron-ore, on Red mountain, Jefferson county, Ala., I asked what were the geological relations of this remarkable deposit. In reply I was told that it was a limestone colored and saturated by some unknown but wholly external influences, and that at a reasonable distance from the surface the color would disappear. I could find no satisfactory explanation either of the nature of this wonderful external permeating influence, or of the cause of such a ferrous impregnation selecting this one particular bed of limestone, to the exclusion of the higher and lower beds of the same material which are not even stained. I. THE PRESENT THEORY. Referring to this subject, Dana says:' "The clays, clayey sandstones and limestones of the Clinton epoch, through New York and the Appalachians, show that the mud-flats and sand-banks, and hence the shallow seas of the coast region, still continued. . . The beds of argillaceous iron-ore, which spread so widely through New York and some of the other States, south and west, could not have formed in an open sea, for clayey iron-deposits do not form under such circumstances. They are proof of extensive marshes, and, therefore, of land near the sea-level. The fragments of crinoids and shells found in these beds are evidence that they were, in part at least, salt-water marshes, and that the tides sometimes reached them." At first, this explanation seemed satisfactory, but the more I studied the ore the less satisfying the explanation became. 1. In the ore itself I found associated with the small particles of rounded matter (now consisting of iron oxide in which organic structure, if ever present, has become lost, though the

Nov 1, 1905