Search Documents

By Q. G. Reynolds

The presence of dust and fume suspended in the freeboard region is a common feature of the operation of direct current (DC) plasma smelting furnaces. This occurs primarily as a result of the use of fine feed materials together with the open-arc, open-bath operation of such smelters, and is exacerbated by the high velocities and turbulent mixing of the gas in the vicinity of the arc jet. Dust and fume losses into the furnace off-gas system can be significant in some cases and may have economic, operational, and environmental impacts on the process. A computational modelling study is presented in which the concentration of dust material was considered as a continuous field subject to a governing partial differential equation. Settling behaviour was calculated as a function of particle size, local gas/plasma temperature, and other physical properties. Development of the coupling between the concentration field and a magnetohydrodynamic description of the arc is shown, and the resulting models were used to compute various aspects of the behaviour of the concentration field in the arc region for a variety of furnace conditions. Time-averaged as well as transient models of the arc were used to generate the results presented. Qualitative case studies produced several practical suggestions for furnace operation, including increased dust capture by the bath when feed ports are located closer to the electrode, and the possible effects of feed segregation in the furnace freeboard based on dust particle size and density.

Jan 1, 2015

By Xiang Li, Xibing Li

It is paramount that the stability of rock slopes be correctly accounted for under diverse operating and environmental conditions. Owing to different sources of uncertainty entailed in such stability problems, conventional deterministic approach through the calculation of a factor of safety (FOS) cannot reflect quantified uncertainties explicitly and sufficiently. Thus it is highly desirable to invoke the reliability approach to consider uncertainties in a systematic manner. Nowadays, the current design standards have an increasing tendency to ensure rock slope stability by pre-defining a target reliability index (or target probability of failure), viz., the reliability level of a rock slope is pre-set as a target to be satisfied. In such a situation and considering the fact that the FOS used as an indicator of slope performance still has a very wide acceptance, we focus on proposing an inverse-reliability-based methodology which aims at developing a two-fold indicator strategy, i.e., using the FOS and reliability together to deal with slope stability problems. The basic idea behind it is to utilize a so-called inverse first-order reliability method (IFORM) to directly calibrate the FOS provided the target reliability index has been given. In this way, the calibration scheme relating the FOS can be rationally done by not only incorporating uncertainties, but also satisfying a desired level of the prescribed reliability. Based on this, to make the IFORM computationally feasible and also reduce its computational cost, we introduce the response surface method (RSM) to generate a surrogate for the FOS-based limit state function (LSF), considering the lengthy and complicated form of the FOS in some recognized methods (e.g., within the framework of limit equilibrium). Distinguished from the existing RSMs that potential inadequacies may arise, we present an RSM based on a hybrid approach combining support vector machine (SVM; used as a regression technique) and uniform design (UD; pertaining to experimental design). Using a representative example of rock slope stability problem, we demonstrate the feasibility and validity of the developed methodology, during which the associated sensitivity study and further discussion are also performed. By dint of such a methodology, we can establish a link between the conventional deterministic approach and the reliability approach, where a logical and realistic framework is provided, for cases achieving the specified reliability, to assist in selecting the FOS which remains adequate for rock slope stability even in the face of uncertainty.

Jan 1, 2015

By Randy McMeekin, Chris Twigge-Molecey, J. Peter Blake

The business objectives of a metallurgical project determine targets and constraints, such as the range of products, production capacities, in-service dates, and capital and operating cost parameters. Permitting is usually left to the project team, as are decisions regarding site location, technology, and construction approach. Success requires an orderly methodology, represented in this book by front end loading (FEL) phases: FEL1 examines several alternative approaches; FEL2 ranks and eliminates less economically or technically attractive options; and FEL3 develops the preferred option to the point of major permit completion, with defined scope, schedule, and cost to submit for approval to proceed with implementation in FEL4. Working through FEL1, FEL2, and FEL3, the project definition improves, estimates become more accurate, and project risks are reduced. The project design basis at the end of FEL3 is the control document for project implementation in FEL4.

Jan 1, 2015

By J. A. Luckmann

"SynopsisThe purpose of this paper is to introduce an innovative approach to risk management in surface mining operations, namely, positive risk. Traditionally, risk management focused on mitigating losses (negative). Positive risk, on the contrary, reverses the approach and focuses on exploiting a project’s inherent benefits (positive).The inability to accurately determine project objectives during the project planning phase and the failure to achieve those objectives during the execution phase is a major problem for any project management in the mining environment.The advance of computer aided design models for mine planning enables mining engineers to examine various options within a very short time. Employing positive risk management combined with drivers-based risk management when evaluating these options provides an ideal opportunity to investigate areas for improving the mining project’s profits. Furthermore, harnessing positive risk returns during the planning phase contributes immensely to the successful achievement of project objectives.Mining has inherent business risks, which can appear overwhelming when considering the risks associated with a mining project schedule, cost, and safety or resources, etc. The question is – how to manage risks in a surface mining environment, and what process methodologies, work methods, processes, and standards should be used when considering the surface mining risks. Applying the principles of positive risk management to manage surface mining risks is not only relevant, but definitely beneficial to mining projects and to the mining industry as a whole.It would be beneficial for risk managers and risk professionals to understand the roles of positive risk ‘drivers’, also known as ‘propitious attractors’. Identifying, analysing, estimating, and understanding the propitious attractors, their behaviour and their influence on project risk events helps considerably during the planning and execution phases. The theoretical and practical knowledge of both sides of the risk – the downside risk (negative risk) and upside risk (positive risk) – can add substantial value to any organization when downside risk is adequately mitigated and upside risk is beneficially exploited."

Jan 1, 2015

By L. du Preez, J. D. Steenkamp

This paper introduces the concept of clean steel production from a pyrometallurgist’s perspective to the broader metallurgical community. A simplistic overview of the steelmaking process from iron ore to car body manufacturing is followed by an introduction to the South African steel industry and the technologies that it utilizes. The process is illustrated by an overview of the flow sheet and technologies for the production of clean steel at Saldanha Steel, South Africa.

Jan 1, 2015

By B. C. Viljoen

"SynopsisCommencement of the next phase of the Lesotho Highlands Water Project is a year or so away from becoming reality. Some 50 km of tunnels in the form of access adits, shafts, diversion tunnels, and main waterways will be constructed. Sprayed concrete will form an integral part of the temporary and permanent rock support systems that will be installed. Furthermore, the use of sprayed concrete as a final tunnel lining solution was proposed as a viable alternative to concrete linings in the feasibility studies that preceded the forthcoming implementation phase.The aim of this paper is to make the reader aware of all the sprayed concrete related issues that engineers tend to grapple with during the design and construction of tunnel projects and other underground works. Primarily, these issues would include selection of applicable design parameters, technical specifications, construction application methods, quality control and, most importantly in the context of final or permanent linings, the durability of sprayed concrete.The International Tunnelling Association (ITA) Working Group (WG) 12 has been tasked specifically to publish a set of recommendations on the Quality and Control of the Application of Sprayed Concrete and the Testing of Sprayed Concrete for Durability. These tasks were also further explored at the recent World Tunnel Congress (WTC 2015) that was held in Dubrovnik, Croatia at the end of May 2015.IntroductionSprayed concrete is presented in a variety of shapes, designs, forms, application methods and accompanying terminologies including shotcrete, gunite, pneumatically applied concrete, and the like. The International Tunnelling Association (ITA) decided to standardize on a single terminology, namely ‘sprayed concrete’, in order to simplify specification, interpretation of guidelines, and codes of practice."

Jan 1, 2015

By P. Eger, D. Green

"The Soudan Mine was Minnesota’s first iron mine, operating from 1882 to 1962. The mine was donated to the State of Minnesota in 1963 and became a state park in 1965. The mine discharge contains elevated copper and cobalt concentrations and has been treated with an ion-exchange-resin-based system since 2009. The system includes flow equalization tanks, bag and cartridge filters, a carbon tank and two commercial ion exchange tanks. Although effective, the system’s high cost, inefficient removal of suspended material and substantial maintenance have been ongoing and troublesome issues.In November 2012, we initiated a pilot test using a peat-based sorption media. This media is produced from raw reed-sedge peat through a patented, low-temperature carbonization process that produces a hardened granular sorption material. The granules are uniform, have high hydraulic conductivity and maintain the high metal affinity of natural peat.Mine water was pumped through the peat-based sorption media without any pretreatment. Copper input concentrations typically ranged from 30 to 60 µg/L but increased to a high of 364 µg/L in the summer of 2013. Since startup, more than 60 million L (16 million gal or 32,000 bed volumes) have been treated, with average removal rates of 75 percent for particulate copper and 60 percent for dissolved copper. Backwash is required at about 4,000 bed volumes, but with a combination of air sparging and high-flow backwash, the suspended material is removedfrom the media.One tank of the peat-based sorption media was found to remove copper similarly to the first four components of the existing system. By reducing size and complexity, reductions in operation and maintenance costs are possible. A comparison of the estimated costs indicate that replacing the four initial components with the single media tank has the potential to reduce annual operating costs by more than half from around $163,000 to $70,000."

Jan 1, 2015

By J. P. Harrison, K. Gao

It is well known that in situ stress measurements at a given site will generally display significant variability. However, it appears that a robust analysis of such measurements – i.e., one that is faithful to the tensorial nature of the data – is not available. Despite the fact that stress is a tensor, stress magnitude and orientation have long been analyzed separately using classical statistics. In earlier work we demonstrated the applicability of tensor statistics to the analysis of stress variability. Here, we investigate further the difference between tensor and classical statistics with respect to the stress tensor correlation matrix. Our analysis commences with the selection of a series of valid correlation matrices. Then, assuming that standardized tensor components follow the multivariate standard normal distribution, these correlation matrices are used to generate marginal probability distributions of the eigen-parameters (i.e., principal stress magnitude and rotation angle). From these, random stress tensors are generated, their eigenparameters determined, and the probability density distributions of these obtained using both classical and tensor statistics. Our results indicate that, for all correlation matrices, both methods give practically identical distributions for principal stress magnitude. However, the discrepancy between the two methods with regard to probability density distribution of rotation angle is highly dependent on stress component correlation. This discrepancy is usefully quantified in terms of the integral, with respect to orientation, of the difference between the two probability density distributions. This parameter, which we term Area Difference, is closely linked to the magnitude of the correlation matrix determinant, which itself is related to the normal stress correlation coefficient (i.e., ?x ,?y ??). Assuming that Area Difference should not exceed 0.1, we identify the critical determinant for any particular value of normal stress component correlation coefficient. Thus, using published in situ stress data and the obtained critical determinants, we show that for a specific normal stress component coefficient, when the correlation matrix determinant is less than its critical determinant, the more precise tensor statistics should be used to calculate the distribution of rotation angle. These results demonstrate that the customary analysis of stress measurement data may lead to erroneous results, and that tensor statistics appears to be preferred approach.

Jan 1, 2015

By Rong. G., T. Q. Lin, W. Du

Based on analysis of the evolutionary history of the valley in Baihetan, the mechanism of asymmetrical evolution, gradual migration-incision evolved from left bank to the right, is revealed in Baihetan river valleys. The process of in-situ stress evolution is carried out by using the Universal Distinct Element Code (UDEC). Consequently, the numerical results which indicate the main regulations of that stress field are as follow: (1) The phenomenon termed "high in-situ stress fold" appears in the bottom of the valley. With the maximum principal stress being 28-34 MPa, the stress increases significantly at a vertical depth of approximately 130 m. (2) The in-situ stress presents zonal distribution along the bank slope. It is apparent that the in-situ stress field consists of stress relaxation zone (SRZ), stress concentration zone (SCZ) and original stress zone (OSZ). The horizontal depth of stress relaxation zone varies from the left bank (roughly 200 m) to the right (about 120 m). Furthermore, the stress evolution of the left bank slope is studied. As a result, it is found that asymmetrical erosion contributes to the difference of the in-situ stress distribution as a critical factor, between the left bank and the right. And for an asymmetrical valley, the evolutionary process of in-situ stress field is a circular procedure, which includes the incision of valley, the accumulation of landslides and the migration of valley.

Jan 1, 2015

By F. S. Su, P. Z. Pan, X. T. Feng, F. Yan, W. W. Ji

"This paper aims to simulate the spalling failure behavior in hard rock based on a self-developed numerical model, i.e. a rock discontinuous cellular automaton (RDCA). A crack initiation and propagation criterion is proposed based on the plastic strain, which is used to link the continuity and discontinuity during the failure process. The discontinuities of rock, such as cracks and other internal boundaries, are represented by discontinuous displacement functions, i.e. tip enrichment and step enrichment. The partition of unity is used to improve integral precision of the elements intersected internal boundaries, which is traced by a level set method. Arbitrary crack geometries can be conveniently represented and it does not require any remeshing in the modeling of crack initiation, propagation and coalescence. Numerical modeling of excavation in hard rock using RDCA is conducted. The spalling failure process of hard rock induced by excavation is well simulated. The depth and shape of hard rock spalling failure are good agreement with in situ observation.INTRODUCTIONThe excavation in rock mass is more and more popular. At the same time, the disasters, such as rock burst, rock spalling and falling etc, induced by excavation are quite prominent. Numerical modeling is an important way to help us understand the failure mechanism of rocks. Many numerical methods have been used to simulate the excavation of rock mass. For example, the finite element method (FEM) (Karakus and Fowell, 2003), the discrete element method (DEM)(Cundall and Strack, 1979, Labra et al., 2008), Finite difference method (FDM)(Zhu et al., 2009), Element Free Galerkin Method (Belytschko et al., 1994), Discontinuous displacement analysis (DDA) (Shi, 1988) and Boundary element method (BEM) (Katsikadelis, 2002, Chen and Hong, 1992) are commonly found in the stability analysis of excavation in rocks. In the modeling of crack propagation or excavation, most of these methods are tedious since the internal boundaries have to be consistent with the element boundaries. And in many cases, the remesh has to be conducted. In recent years, people are interested in particular types of FEMs, such as the extended finite-element method (XFEM), the particle discretization scheme finite-element method(PDS-FEM(Hori et al., 2005, Oguni et al., 2009)), the combined finite-discrete element method (FEM/DEM) (Munjiza and Wiley, 2004, Cai, 2008) and spectral-element method(Gharti et al., 2012) etc."

Jan 1, 2015

By William R. Kohl, Craig B. Clemmens

"Since 2010, North Central Resources, Bridgeport, WV, has been using the sonic log to estimate the rockmechanics properties of the coal and adjacent strata in their exploration drilling program. In 68 out of the 85 boreholes they have drilled since 2010, they have conducted shear wave analysis on sonic logs run in these boreholes. By incorporating the rock mechanics logs into the geological model of the coal seam, the engineers can develop a better understanding of the support requirements for the mine.WellCAD Borehole processing software provides vastly improved efficiency in analyzing shear waves from borehole sonic data than previously available methods. The calculation of most rock mechanics parameters requires knowledge of the density and both the compressional wave velocity and the shear wave velocity. Density logs are well known and an industry standard. Sonic logging is equally well known, although less frequently used, as an accurate source of compressional wave velocity. Shear wave velocity is difficult to measure in a geophysical log, but can be estimated from digitally recorded wave form records. This is a time consuming manual procedure which requires the visual examination of thousands of individual wave forms.WellCAD allows the viewing all the wave forms on a VDL display. The observer can create a pair of false logs by manually tracing the interference points on the display for each receiver. He can check himself by observing wave forms in the traditional format. He can then create a shear wave transit time log or “Delta-S” log by subtracting the false log from the near receiver from that of the far receiver. This can be plugged into standard formulae to generate curves for most standard rock mechanic parameters, including bulk modulus, shear modulus, Young’s modulus, and Poisson’s ratio.While these parameters do not entirely substitute for destructive testing, they are extremely cost effective. An entire borehole can be analyzed for the cost of a single destructive test. This allows for a more judicious use of destructive testing while permitting the extension of test data into the rock mass with much greater confidence."

Jan 1, 2015

By J. -F. Blais, M. -O. Simonnot, J. Mocellin, G. Mercier, J. -L. Morel

Large quantities of ferromanganese sludge are generated as waste material by blast furnace during the manufacturing of ferromanganese. These slags are very rich in manganese, zinc and lead (5 to 40 %). These residues have been deposited in a pond in periphery of the steel industry. Considering the market value of the metals, these brownfield sites can now be considered as secondary resources. We have developed a hydrometallurgical process for selectively leaching Zn, Mn and Pb in order to produce compounds of Mn and Zn pure enough to be economically recoverable and a residue rich in Pb. Batch laboratory experiments were carried out to determine appropriate leaching conditions to maximize zinc extraction (100 %) and manganese extraction (90.0 %) with sulfuric acid and to generate a residue containing 15 to 30% of lead. This Pb residue is recyclable by another process.

Jan 1, 2015

By B. Chareyre, H. Pourpak, L. Scholtès, E. Papachristos

"Numerical methods used to study hydraulic fracturing in low permeability rock masses need to take into account the interaction between the progressive failure mechanism of the intact rock matrix and the pre-existing natural fractures. A fully coupled hydro-mechanical 3D discrete elements model dealing with such interaction is presented here. The ultimate objective is to grasp the role of the rock-matrix failure on the propagation of the main fluid driven fracture under different stress fields and pre-existing fracture orientations. The proposed method provides the spatiotemporal distribution of the induced crack events which can be tracked during the simulations, making possible the identification of the local mechanisms leading to macro-failure in the rock matrix or reactivation of the discontinuity planes. Fluid flow inside a fracture, pressurized crack and hydro-fracking experimental tests were simulated as part of the validation process of the model and, are presented in this paper.INTRODUCTIONWith the expansion of shale gas and geothermal reservoirs exploitation, the technique of Hydraulic Fracturing (HF) has been widely used over the past years (McClure, 2012; Britt, 2012). Despite recent advances in micro-seismicity analysis or numerical modeling (Nagel et al., 2013), the way progressive failure of rocks affects the fluid flow depending on the in situ stress conditions or the rock heterogeneities is not fully controlled yet (Zoback, 2010).In this work we focused on setting up a three-dimensional discrete elements model to study fluid driven fractures propagation. The intact rock is modeled by a discrete element method (DEM) able to reproduce fracture initiation and propagation (Scholtès and Donzé, 2013, Garcia et al., 2013). The pre-existing fractures are explicitly modeled and can be individually defined or be part of a discrete fracture network (DFN) (Harthong et al., 2012). Their mechanical response is fully coupled with the fluid within a HM-DEM framework. The fluid flow and it’s interaction with the intact matrix and the pre-existing discontinuities is modeled through a Pore-scale Finite Volume (PFV) scheme specially enhanced for fractured rock modeling (Chareyre et al., 2012, Catalano et al., 2014) ."

Jan 1, 2015

By Joshua Micah Hoffman, Jhon Silva-Castro, Kylie Larson-Robl

A coal mine impoundment failure has the potential to be environmentally devastating and life-threatening. It is well documented that after seismic events slope failures in impoundments can occur. It has been concluded that often the main driven factor of the failure is the increase in excess pore pressure due to ground vibration. A small amount of research has been done regarding the stability of coal mine impoundments under natural seismic events; however no research has been done considering vibrations from mine blasts. If it is taken into account that current environmental restrictions oblige to increase the capacity of coal mine impoundments, thus increasing the hazard of such structures, it is necessary to evaluate the effects of near-by mine blasting on the stability of the coal mine impoundments in order to mitigate and control the potential of slope failures. To study the behavior of excess pore pressure under blasting conditions, scaled simulations of production blasting events were set up inside of a controlled sand tank. The research was divided in two stages. The first one was done, using dry conditions, while in the second part, the same set of tests were performed under saturated conditions. This document shows the partial results for stage one (dry conditions). For the tests, explosive charges were set off within the sand tank at various distances to simulate different blasting distances. Information was collected from geophones, accelerometers, microphones and high speed video camera for dry and saturated scenarios and additionally from piezometers under saturated conditions to assess the behavior of the material under blasting conditions.

Jan 1, 2015

By Joseph Hirschi, Naga S. Y. Tirumalaraju, Aditya Mishra, Anthony (Sam) J. S. Spearing

"Primary roof support in underground coal mines in the USA consists mostly of fully grouted passive rebar or grouted (partially or fully) tensioned rebar. Research conducted at two room-and pillar coal mines in the Illinois Basin and one longwall mine in Colorado monitored the performance of these passive and active rock bolts under similar geologic and mining conditions and found no significant initial loads in either passive or active rock bolts (Spearing et al., 2011). Active rock bolts showed significant loss of initial pre-load, although the exact reasons for this were not fully investigated. Subsequent laboratory testing has also shown that in weak rock, resin creep occurs, caused by slippage of the mechanical key between resin column and rock interface. These creep tests were studied in the laboratory in an effort to quantifythis phenomenon.INTRODUCTIONResin-grouted rock bolts are the first and main line of defense to counter roof and rib falls in underground coal mines of the United States. Rock bolts are categorized as active or passive. Active bolts are tensioned during installation whilst no (or limited) tension is applied to passive bolts, which need subsequent strata movement to generate reactive loads. During installation of passive bolts, some reactive pre-load may be generated by a significant up-thrust from the rock bolter boom.The selection of active or passive bolts is critical and is mostly dependent on the conditions and properties of the immediate roof (Unrug, 2009). This decision is frequently made based on personal experience, bias, and most recently cost. Active bolts are generally used in cases of highly laminated roof rock. When active bolts are tensioned, they develop compressive forces between these layers forming a beam, which helps to stabilize weak individual layers thereby increasing frictional forces between layers and decreasing effects of horizontal stresses. The fully grouted tensioned rebar system is high in stiffness as compared to mechanical bolts and provides higher surface area of contact along the length of the bolt due to the grout, which permits it to develop a strong anchorage mechanism."

Jan 1, 2015

By Olaf Kessler, Jan Kalich, Michael Reich, Julia Osten, Uwe Füssel

Modern automobile bodies consist of different materials, e.g. aluminium alloys and high strength steels. Mechanical joining, e.g. clinching, is very suitable for joining aluminium and steel sheet. But clinching needs a sufficient ductility, which is no longer supplied by high strength steels. Laser-assisted clinching has been shown, to be able to join aluminium and high strength steel sheet successfully. Thereby the steel sheets were heated locally for short times to increase their ductility. Due to the thermal contact between steel and aluminium sheet the aluminium alloys also achieve a local short-time heat treatment. This fact may cause a significant impact, as aluminium sheet in automobile bodies is often used in T4 (or similar) condition and later artificially aged during the paint bake cycle. Aluminium alloys 6016 and 6181 have been short-time heat treated with heating rates up to some 100 K/s. Precipitation and dissolution processes have been monitored in-situ by calorimetry. Mechanical properties have been investigated on as well as after short-time heat treatment by deformation dilatometry. The results show, that suitable short-time annealing parameters during laser-assisted clinching can increase ductility and at the same time act as retrogression for aluminium sheets, resulting in increased strength after aging.

Jan 1, 2015

By C. T. Aimone-Martin, V. L. Rosenhaim

The response of two structures to blast-induced ground vibrations were evaluated and compared in order to quantify the impact of different blasting operations, hard rock and soft rock blasting, upon the structures movements. The first instrumented structure was a residential type, located in the operational area of a coal mine, were blasting is conducted in soft rocks, such as siltstone and coal, with compressive strength ranging from 20 to 50 MPa. Blasting is characterized by low benches, with hole lengths averaging 5.5 m (18 ft) and low powder factors, 140 to 210 g/m3 (0.236 to 0.354 lb/yd3), resulting in very little horizontal movement of the rock during the blast. The second structure was a commercial building, located in a basalt quarry (compressive strength between 109 and 180 MPa), where blasting is conducted in 12 m (39.4 ft) benches with powder factors ranging from 200 to 350 g/m3 (0.337 to 0.590 lb/yd3). Velocity sensors were placed on the structure walls to measure wall displacements and calculate blast-induced strains in the walls, and these results were compared with the driving ground excitations. The calculated strains were compared with the limits of rupture of the cement grout used as mortar between bricks and as wall coating, considered to be the weakest material in the structure composition. The blast-induced response of existing cracks in the structures were also measured using displacement gages and compared to the daily influence of weather fluctuations, such as changes in temperature and humidity, on crack movement. The results show that for the same levels of ground motions the structures present different movement, resulting in distinct levels of induced strains on the walls depending on the geology. The influence of long-term temperature and humidity variations on crack movements on both structures is very similar, during the same seasons of the year. Crack response to long-term weather changes is 2.5 to 3.5 times greater than blast influences.

Jan 1, 2015

By P. Mišcevic, B. Kavur, I. Vrkljan, N. Štambuk Cvitanovic

It is known from earlier and recent research that mechanical properties of intact rock like uniaxial compressive strength (UCS), Young's modulus (E) and Poisson's ratio (?) are influenced by shape deviations of test specimens as deviations from the ideal cylinder. That impact can be significant at certain level of inaccuracy of specimen preparing, and it should be objectively evaluated and controlled in testing. The effects of intact specimens side straightness, ends flatness, ends parallelism and perpendicularity to the specimen axis, on UCS, E, and ?, measured in several actual ways during laboratory compression tests, were determined by previous research on 90 homogeneous specimens of limestone. In this paper, we subject these new experimental results to Response Surface Methodology (RSM) to model the mentioned dependence, to identify significant connections of variables and to evaluate the conclusions obtained directly from experimental phase. This study indicates how the responses of the model (outputs) – parameters UCS/E/??of limestone rock depend on factors (inputs) – parameters of specimen shape deviations like flatness R, parallelism P and perpendicularity O, assuming modern test machines with spherically seated upper platen. Starting from general RSM model with three factors (R, P, and O), we investigated the multiple linear regression models of specific mechanical property (UCS, E, and ?). Using the NCSS program ("NCSS 2004 and PASS 2005") in several steps, final models with very high coefficients of determination were developed for properties with the most evident effects of specimen shape deviations: nine models for strength UCS and UCS50 (equivalent UCS for specimen with 50 mm diameter), and three models for ?L (Poisson's ratio calculated from axial deformations measured on the entire specimen length). These statistical models with their response surfaces further strengthen and confirm the results and conclusions from the experimental phase. The critical values of R, P, and O are established using an additional statistical analysis to determine the lower and upper engineering limits. These findings set the basis for the new eligibility criteria for specimens of limestone (and similar rock with UCS about 100-150 MPa) in further testing of strength and deformability.

Jan 1, 2015

By H. P. Kang, Y. J. Feng

The hard roof in underground coal mines is generally considered as a main cause that induces disasters in working faces and entries, such as rock burst and windblast. Hydraulic fracturing technology is an effective approach to weaken hard roof to reduce ground pressure and control rock burst. The state and achievements associated with hydraulic fracturing technology applied in Chinese coal mines are summarized in this paper. Theories related to hydraulic fracturing are of the essence in fracture design to determine the fracture initiation and propagation pressure and predict the geometry and the characteristics of hydraulically induced fractures. Initially, theory of elasticity was employed to determine the breakdown pressure for a vertical borehole where the rock medium is assumed to be elastic. However, porosity and pore fluid have an influence on the borehole breakdown pressure, and then the poroelasticity theory was applied. Arbitrary deviated boreholes in practice are rather common and the maximum tensile stress criterion was employed to determine borehole breakdown pressure. The effect of natural crack in the rock medium on the initiation pressure has been taken into consideration through fracture mechanics. Meanwhile, considerable achievements have been made on hydraulic fracturing tools and equipment, and a set of mature hydraulic fracturing technologies for hard roof control are available. Some comprehensive investigations on the hydraulic fracturing for hard roof weakening are presented, and successful field applications in the Jincheng and Luan coal mining districts are introduced. Finally, the unsolved problems related to hydraulic fracturing are also put forward.

Jan 1, 2015

By Pinnaduwa H. S. W. Kulatilake, Biao Shu

The intact rock properties and discontinuity properties for both Devonian Rodeo Creek (DRC) and Devonian Papovich (DP) rock formations that exist in the selected open-pit mine were determined from tests conducted on rock samples. Special survey equipment, which has a total station, laser scanner and a camera, was used to perform remote fracture mapping in the research area. From remote fracture mapping data, the fracture orientation, spacing and density were calculated using more refined procedures compared to what exist in the literature. Discontinuity orientation distributions obtained through remote fracture mapping agreed very well with the results of manual fracture mapping conducted by the mining company. The GSI rock quality system and Hoek-Brown failure criteria were used to estimate the rock mass properties combining the fracture mapping results with laboratory test results of intact rock samples. Fault properties and the DRC-DP contact properties were estimated based on the laboratory discontinuity test results. A geological model was built in a 3DEC model including all the major faults, DRC-DP contact and two stages of rock excavation. The built major discontinuity system of 44 faults in 3DEC with their real orientations, locations and three-dimensional extensions were validated successfully using the fault geometry data provided by the mining company using seven cross-sections. Numerical modeling was conducted to study the effect of boundary conditions and lateral stress ratio on the stability of the considered rock slope. For the considered section of the rock slope, the displacements obtained through stress boundary conditions seemed more realistic than those obtained through zero velocity boundary conditions (on all four lateral faces). Stable deformation distributions were obtained for k0 in the range of 0.4 to 0.7. Because the studied rock mass is quite stable, it seems that an appropriate range for k0 for this rock mass is between 0.4 and 0.7. The displacements occurred between July 2011 and July 2012 due to the nearby rock mass excavation that took place during the same period; they were compared between the field monitoring results available from the mining company and the predicted numerical modeling results and a good agreement was obtained. Overall, the successful simulation of the rock excavation during a certain time period indicated the possibility of using the procedure developed in this study to investigate rock slope stability with respect to expected future rock excavations in mine planning.

Jan 1, 2015