Search Documents

By Kang-Hyun Lee, In-Mo Lee, Byung-Kyu Kim, Parkm Jinho, Seoung-Won Lee

"In this study, the TBM Resistivity Prediction (TRP) system is developed for predicting the location, thickness, permittivity ratio and electrical conductivity of anomalous zones ahead of tunnel face using the measured resistivity of the ground. The applicability of the developed system was verified by performing field tests at a construction site in which an EPB-shield TBM is used for tunnelling work. In the first field test, it was found that the rock around the tunnel face had the same resistivity and permittivity with the rock ahead of the tunnel face indicating no anomaly ahead of the tunnel face. In the second test, a stronger zone 5-m thick was predicted ahead of the tunnel face based on lower permittivity than that of the rock around the tunnel face. The ground condition assessed by the newly developed TRP system matched well with that either predicted from geophysical exploration or directly obtained from drilling boreholes or from daily observed muck conditions. INTRODUCTION During tunneling work, the emergence of unpredicted zones of relatively weaker or stronger ground can lead to delays in construction work or an increase of construction cost. Predicting anomalous zones ahead of tunnel face in advance can thus prevent time and economic loss. For these reasons, various methods to predict the ground condition ahead of the tunnel face have been studied and developed. Prediction methods using various kinds of equipment include tunnel seismic prediction, ground penetrating radar, electromagnetic surveys based on electronic antennas, and electrical resistivity surveys conducted by analyzing electric currents in the ground ahead of the tunnel face (Ryu et al. 2008). However, most of the prediction methods are only applicable to conventional tunneling job sites, which feature free access to the tunnel face. In mechanized tunneling projects, accessibility to the tunnel face is very limited because the tunnel face is occupied by the TBM."

Jan 1, 2016

By Patricia Pride, Kurt Bettger, Jack Raymer

"INTRODUCTION The Jefferson Barracks Tunnel is in the final stages of design and is expected to go out to bid in the summer of 2016. The project is located in south St. Louis County along the west bank of the Mississippi River, about 13 km downstream of the St. Louis Gateway Arch. The project consists of a deep sanitary sewer tunnel, a deep pump station and several intakes. The intakes will divert sanitary flows into the tunnel and the tunnel will convey the flows by gravity to the Lemay No. 3 Pump Station, which will pump them up into the Lemay Waste Water Treatment Plant. The tunnel is about 5.4 km long and will be lined with 84-inch (2.1 m) fiberglass pipe. It drops at a gradient of 0.1 percent from south to north and will be bored through strong limestone using a hard-rock tunnel boring machine (TBM). The diameter of the TBM is anticipated to be about 3.4 m. The Owner’s original concept was for a relatively shallow tunnel so as to minimize construction and pumping costs. The preferred alignment ran close to the river, next to the existing force main, which was to be abandoned. Keeping the tunnel close to the force main would reduce the amount of shallow sewer work needed to connect the existing feeder sewers to the new tunnel. Several geotechnical investigations were performed, with shallowly focused geophysics and the borings all going exactly down the conceptual tunnel depth. Limestone bluffs run along the Missouri side of the river. These bluffs are pockmarked by sinkholes and riddled with karst. Large, well-known caves occur both north and south of the alignment. Karst features, including deep crevices and possible caves, were found in those early geotechnical investigations. Many of these features extended well below the level of the Mississippi River and would have been encountered by the tunnel. If a large crevice or cave were encountered, then the inflow of mud and water into the tunnel could have been large and possibly uncontrollable. Something had to be done to mitigate this situation. Pre-excavation grouting was considered, but the program would have been huge and extremely expensive. Using a closed-face TBM with bolted and gasketed lining was also considered, but that too was both risky and extremely expensive. The Owner could have abandoned the tunnel altogether and built a new force main, but that would have brought a whole new set of problems and was undesirable to the Owner. The last option was to move the tunnel away from the karst."

Jan 1, 2016

By C. Musingwini, A. S. Nhleko

"Since the Global Financial Crisis (GFC) in mid-2008, capital has been more difficult to access. Mining projects must contend with projects from other industries for scarce capital. A decision to invest available capital in mineral projects requires that valuation be conducted to assess the expected return on the projects. The discounted cash flow (DCF) analysis is generally applied for the valuation of mining projects, whereby future cash flows are discounted to present value using an appropriate discount rate. The discount rate significantly affects the outcome of a valuation. Economic and finance theory provides tools to calculate discount rates. The discount rate must account for factors such as the risk and stage of development of the mineral project; hence the appropriate discount rate to utilize in a project is often a subject of debate.The discount rate is the weighted sum of the cost of debt and equity. There are several methods for determining the cost of equity. This study considers the commonly applied Capital Asset Pricing Model (CAPM) and Gordon’s Wealth Growth Model because of their simplicity and availability of parameters required to estimate the cost of equity. This study explores how differences in the cost of equity obtained by these two methods can be explained for a mining environment. Data for empirical analysis were collected from the I-Net Bridge, McGregor BFA, and Bloomberg databases. It was found that Gordon’s Wealth Growth Model provides better estimates of the cost of equity compared to the CAPM under depressed market conditions. Therefore, this research recommends that Gordon’s Wealth Growth Model be used to estimate the discount rates for mining projects during periods of depressed market conditions."

Jan 1, 2016

By P. Hickey, G. Hubert, P. Healy

"J. S. Redpath Limited, an underground contractor with a worldwide presence, has implemented innovative techniques in various projects in Canada to shorten the development cycle. Conventional methods currently used for installing primary ground support are compared with the Australian technique of bolting and meshing with jumbos equipped with twin telescopic booms, in-cycle shotcreting, and the use of two jumbos and two scissor bolters set up side by side in wide headings. Recommendations and lessons learned are presented with the aim of providing realistic expectations with regard to development advance rates in a mining environment.RÉSUMÉ J. S. Redpath Limitée, un entrepreneur minier souterrain d’envergure mondiale, a complété plusieurs projets au Canada où des techniques novatrices ont été mises en oeuvre pour raccourcir le cycle de développement. Cet article présente une comparaison entre les méthodes conventionnelles fréquemment utilisées pour le support de terrain, la technique australienne de boulonnage et d’installation de grillage au moyen de jumbos équipés de flèches télescopiques doubles, du béton projeté appliqué durant le cycle de développement et de l’utilisation de deux jumbos et deux boulonneuses côtes-à-côtes dans des galeries de grandes dimensions. Les recommandations et les leçons apprises sont présentées dans le but de fournir au lecteur des attentes réalistes quant aux taux d’avancement du développement dans un environnement minier."

Jan 1, 2016

By Q. Ricoux, F. Goettmann, A. Maihatchi

"Electrodeposition processes are widely used in the metallurgical industry to produce, extract and refine metals from various feed materials. However, raw materials used to provide non-ferrous metals often contain high amounts of iron. In the presence of iron, while metals are plated at the cathode, electrowinning processes produce corrosive and highly oxidative ferric ions at the anode that are harmful for the process sustainability. In fact, these ferric ions cause dramatic current efficiency loss, induce high maintenance expenditures to limit the corrosion of devices and it results in the formation of impure and dendritic deposits on the cathode. Consequently, the management of iron in electrodeposition process became a major issue in non-ferrous metals production. Actually, numerous methods have been developed to limit the ferric ion concentration in the electrolyte or, at least, to limit its harmful effect. Many methods aim to limit the iron(III) concentration in the electrolyte, generally by coupling electrowinning to extraction process such as solvent extraction (SX) (Bender & Emmerich, 2015), ion exchange (IX) (Gula, Dreisinger, & Horwitz, 1996) or cementation (Kust, 1979) processes to remove ferric ions. Other routes consist of (i) using the ferric ions oxidant properties to leach raw materials, either directly in the electrolytic cell (Fanta & Tributsch, 1975) or through a secondary circuit (Cain, 1950), or (ii) reducing ferric ions through periodic reversal of direct current to enhance the formation of Fe2+ (Loutfy & Bharucha, 1980). On the other side of the spectrum, papers discuss methods to valorize the iron from by-products of the non-ferrous metal industry, that generates vast quantities of iron containing wastes (A. Agrawal, Sahu, & Pandey, 2004). Many studies on iron electroplating and electrolytic iron production from ores have been carried out (Cain, 1950; Mostad, Rolseth, & Thonstad, 2008), but very few have been conducted on waste or by-products. Therefore, we propose to build on the previous literature review to develop a process for the production of electrolytic iron from by-products.INTRODUCTIONNon-ferrous metals and their alloys are used in a large variety of applications. Aluminum and titanium are used for their strength, light weight and corrosion resistant properties in structural applications. Copper has been used in various applications requiring high thermal and electrical conductivity, as kitchen products and electrical wires. Nickel and zinc are commonly used as plating materials; nickel offers a wide range of working temperature and zinc is used for steel plating. Gold, silver, and platinum group metals are used in electrical/electronic applications, jewelry and chemistry as catalysts."

Jan 1, 2016

By Olivier Kraft, Olaf Kortz

"Project-specific optimized tunnel boring machines represent the spearhead of technological progress in tunneling because with their use, very long-lasting, high quality tunnel structures in almost any geology, depth and topography can be produced with a high degree of automation. The mechanized excavation of tunnel structures ensures the greatest possible environmental protection during tunneling itself. Professional, systematic and high quality rebuilds and reuse of already proven equipment also ensures maximum efficiency in the use of materials and energy resources. It offers an enormous potential for a highly optimized environmental balance. Here the manufacturers of tunnel boring machines and their users in particular have a duty to ensure transparent, high quality and binding standards in the entire rebuild cycle and in the refurbishment management of innovative tunneling technology. This paper deals with the comprehensive processes with rebuild levels of tunnel boring machines and highlights some exemplarily implemented projects. 1 INTRODUCTION All over the world, the number of tunnel boring machines (TBM) in which equipment rebuilds from previous projects are re-used has increased over the last few years. This text presents the technical and economical aspects of this market development. It also takes a look at the practical implementation of rebuild measures. The ""ITAtech Guidelines on Rebuilds of Machinery for Mechanized Tunnel Excavation"" from 2015 lay down the requirements that the machine manufacturers must meet. 2 ECONOMICAL AND ECOLOGICAL ASPECTS OF RE-USING COMPONENTS The globalization of the construction sector and the consideration of environmental aspects promote an increased re-use of machines and machine components. Nowadays, large-scale construction projects are often carried out by international joint ventures of several individual companies that are established specifically for this purpose. After the completion of the project, the joint ventures are dissolved and they liquidate their project-specific equipment, such as tunnel boring machines. Today, it is much more uncommon for such machines to remain permanently in the possession of construction companies. Joint ventures offer TBMs on the free market, or they exercise contractually agreed repurchase options with the manufacturer. On the whole, this increases the number of re-usable components or complete tunneling systems available on the market."

Jan 1, 2016

By R. H. Matjie, J. R. Bunt, C. A. Strydom

"A number of conventional and advanced analytical techniques (proximate and ultimate analysis, low-temperature oxygen-plasma ashing, X-ray diffraction, X-ray fluorescence spectrometry, coal petrography, and lightelement electron microprobe analysis) have been integrated and crosschecked to provide detailed characterization of coals from the Highveld coalfield in South Africa, as a basis for better understanding of the mineralogical and chemical properties of the individual coal sources that are blended as feedstocks for combustion and carbon conversion processes. The techniques included methods to quantify the abundance and composition of the mineral matter (minerals and non-mineral inorganic elements), and also the abundance and chemical composition of the individual macerals in the individual coals concerned.Kaolinite is the most abundant of the minerals in the coals studied, with lesser but still significant proportions of quartz, mica and/or illite, dolomite, calcite, and pyrite. Small but variable proportions of anatase, goyazite, and siderite are present in some coal samples. Electron microprobe analysis, based on a special configuration for light-element study, shows that the vitrinite contains less carbon and more oxygen, and has significantly higher concentrations of nitrogen and organic sulphur, than the inertinite macerals in the same samples. Minor proportions of organically-associated inorganic elements, including titanium, were also identified in some of the maceral components.A comprehensive knowledge of the minerals and non-mineral inorganic elements in the coals used for feedstock preparation, obtained by integration of data from these advanced analytical techniques with more conventional analyses, may be of benefit in understanding the processes that take place during coal utilization, and also in avoiding or ameliorating some of the operational and environmental problems that may occur in different sectors of the coal utilization industry."

Jan 1, 2016

By P. Erskine

"Hyperaccumulator plants can be utilized as ‘metal crops’ in agromining operations. This emerging technology produces ‘bio-ore’ by growing ‘metal crops’ on sub-economic ore materials, such as natural ultramafic soils. In a typical application plant material is periodically harvested, followed by air-drying and incineration to produce the bio-ore intermediate. The bio-ore is of very high grade (>15 wt. % nickel), and of high purity, and may be processed into a number of different products (including nickel metal, nickelbased catalysts and pure nickel salts). Current research efforts from our team focus on Mediterranean climate field trials (Albania, Spain) and tropical climate field trials (Malaysia, Indonesia). Field-scale demonstrations are required to provide evidence of real-life performance and of economic viability. If the trials are successful, agromining may in the near future support local livelihoods with income opportunities as an alternative type of agriculture: to farm nickel.INTRODUCTION AND BACKGROUNDHyperaccumulators, plants with the exceptional ability to uptake and concentrate trace elements in their shoots, can be utilized as ‘metal crops’ in agromining operations (Van der Ent et al., 2013a; Chaney et al., 1998; 2007; Baker et al., 2010). Agromining produces ‘bio-ore’ from harvested ‘metal crops’ grown on unconventional resources such as natural ultramafic soils (Van der Ent et al., 2015a). The bio-ore is a high purity and very high-grade (>15 wt. % nickel) product intermediate that may be turned into a range of different nickel products (nickel metal, nickel-based catalysts and pure nickel salts). The potential for agromining is greatest in tropical regions (Asia-Pacific Region: Indonesia, Malaysia, Philippines, Papua New Guinea and New Caledonia) where very large expanses of ultramafic soils exist (Van der Ent et al., 2013b). Agromine operations may replace existing marginal agriculture on poor ultramafic soils, for example oil palm plantations that require high fertilizer inputs to be profitable, or take place under a cocropping regime. The ability of ‘metal crops’ to achieve high nickel concentrations in biomass (and hence in harvested bio-ore) from soils with just <0.5 wt. % nickel, makes it possible to access non-conventional resources, not accessible by traditional mining techniques. For example, agromining could be implemented both on the large ‘halo’ around the mine leases, and as part of the progressive rehabilitation process after conventional resource extraction. As with all methods for resource extraction, agromining will be finite due to the diminishing concentrations of nickel in the zone accessible by plant roots (Chaney et al., 2014). Nevertheless, considering soil materials with 0.2 wt. % nickel and ‘metal crops’ with a yield of 100 kg nickel ha-1 the agromining venture may be sustainable for decades (Van der Ent et al., 2015a)."

Jan 1, 2016

By T. Wajima

"A novel carbonaceous adsorbent for recovery of nickel from nickel plating waste solution was prepared from rice straw using sulfur impregnation. The rice straws were cut to 1 cm pieces, and then immersed in 0.01 - 3 M K2S solution to prepare sulfur-immersed materials. The immersed-materials were heated at 100-700 ºC in nitrogen gas to produce the sulfur-impregnated carbonaceous adsorbent by pyrolysis. The contents of carbon and sulfur in the adsorbent and abilities of adsorbent to recovery nickel from aqueous solution were examined. The contents of carbon and sulfur in sulfur-immersed materials are almost same as those in raw material. In pyrolysis, with increasing the heating temperature to 200 ºC, the contents of carbon and sulfur are almost constant, and then above 300 ºC those increase. The recovery for nickel using raw material, sulfur-immersed material and the product pyrolyzed at 100 - 200 ºC are almost same, and with increasing the heating temperature to 400 ºC, that of the product increases, and above 500 ºC that of the product decreases. In immerse step, with increasing K2S concentration, the carbon content of the product at 400 ºC gradually decreases, the sulfur content of the product increases, and the recovery for nickel using the product gradually increases and then above 1 M K2S decrease. The product prepared from material immersed in 1 M K2S solution at 400 ºC indicates a maximum recovery for nickel ion. The product can adsorb nickel ion in nickel plating waste solution coexisting with phosphate ion, and adsorbed nickel ion in the product was deposited as nickel metal after heating at 1000 ºC under N2 atmosphere.INTRODUCTIONRice is the second world’s largest cereal crop after wheat, but produces large amount of straw residues, of about 330 million metric tonnes. Rice is a widely grown crop in Asia, and rice straw is produced as a by-product of rice production. In most parts of rice fields, open-field burning of rice straw is commonly practiced in the region when there is limited time to prepare a field for the next crop. However, open-field burning of crop residues is an uncontrolled combustion process during which air pollutants are emitted into atmosphere. These air pollutants have significant toxicological properties and are potential carcinogens (Gadede et al., 2009). Although wildfires are prohibited in cultivation fields of most countries, farmers usually keep on burning their crop by-products. Biomass burning is an important source of aerosol particles which may affect local and regional air quality (Gao et al., 2011), and also contribute to global climate changes."

Jan 1, 2016

By J. T. Liu, G. H. Han, W. C. Chai, Y. F. Huang

"In beneficiation process, metal ions could adsorb onto clay mineral surfaces or interact with flotation chemicals, and then result in the flotation behavior changing of desired minerals. Al(III) is the dominating ion existing in the bauxite flotation system. In this research, the adsorption behaviors of Al(III) on two silicate clay minerals (including bentonite and kaolin) were investigated by means of UV-Vis spectra, zeta potential testing and scanning electron micrograph analysis. The adsorption experiment results show that the adsorption capacity of clays for Al(III) ions increases with the initial Al(III) concentration, contact time and solution pH. There are some different adsorption behaviours for two clays. Increasing the clay concentration decreases the adsorption capacity of bentonite, while increases first then decreases for kaolin. Higher temperature favours the adsorption of Al(III) on bentonite but goes against for kaolin. The adsorption capacities of bentonite and kaolin for Al(III) respectively reach 12.48 and 0.875 mg/g at initial solution pH 5. Zeta potential results show that the adsorption of Al(III) on two clays is characterized by electrostatic attraction mechanism.INTRODUCTIONIn beneficiation process, there is inevitably a wide variety of metal ions generated from mineral crushing, mineral dissolution and water chemistry conditions. Metal ions adsorb on the mineral surfaces or interact with the beneficiation agents, affecting the flotation efficiency of desired minerals (DiFeo et al., 2001; Parolis et al., 2008; Shackleton et al., 2012; Shengo et al., 2014). Therefore, it is necessary to have a detailed investigation on the adsorption behaviour of metal ions on clay minerals.Having good ion exchange capacity and negative surface charge, the clay minerals could take up various metal ions from the mineral-water system. Bentonite and kaolin are very common aluminosilicate clays in the mineral processing system. These two clays both hold a permanent negative charge, =X- on the basal surfaces, and a smaller variable charge, =SiOH on the mineral edges (Gu & Evans, 2008; (Gu et al., 2010). Adsorption experiments are usually used to study the adsorption affinity of metal ions for clay minerals (Sen & Bhattacharyya, 2012). The adsorption of Zn(II), Cu(II) and Pb(II) onto natural bentonite showed that the adsorption amounts of metal ions increase with contact time, solution pH and metal ion concentration, but decreases with adsorbent concentration and system temperature (Sen & Gomez, 2011; Melichova & Hromada, 2013). Cr(III) adsorption on bentonite was significantly pH dependent. The adsorption process followed pseudo-second-order model and the equilibrium adsorption was consistent with Freundlich isotherm (Lollino et al., 2015). The adsorption behaviours of Pb(II), Cd(II), Ni(II) and Cu(II) onto kaolin indicated that increasing pH favoured the adsorption of metal ions (Jiang et al., 2010). The adsorption of Cd(II), Cu(II), Pb(II) and Zn(II) onto kaolin showed that an ion-exchange reaction occurred at pH<7.0 and inner-sphere surface complexes were prone to form at higher pH (Srivastava et al., 2005)."

Jan 1, 2016

By Romel Villanueva L.

"Peru does not produce ammonium nitrate; nevertheless it is a large consumer of both, porous prill (PP) and high-density (HD) varieties. Explosives cost is an important preoccupation in Peru, due tofluctuations of the imported ANFO grade Ammonium Nitrate (AN). The use of Gasified Emulsion (GE)-manufactured with much cheaper HDAN- has become an alternative to reduce such costs. However, some problems were reported in the application of pure GE, including explosive percolation in highly fractured rock and lack of sensitivity by the effect of hydrostatic pressure in very deep holes. It was, hence, proposed to have an explosive based on GE too, but more robust and capable to keep the shape of the explosive column into the blast hole, by minimizing the leakage into the cracks. This could be achieved by adding limited amounts of lower priced HDAN, at the same time of providing gas pressure benefits. Other alternative is to add a low-density material, such as polystyrene prills, into the GE, although it reduces the explosive energy. The chemical gassing controls the density of GE, thus it can be obtained a wide range of densities."

Jan 1, 2016

By C Jincheng, L. Liang, L. Wenjun

"Considering overgrinding in a grinding process, the grinding characteristics of comminuted hematite products using a HPGR and a conventional CC were comparatively studied. The major properties including particle size, grinding kinetics and grinding technical efficiency (Et) were investigated. Individual size distributions (ISDs) of -2.0mm in a HPGR product showed a more significant “double-peak” characteristic than a CC product. As a result, HPGR products were finer and had a wider full-size distribution because of the greater proportion of fines. The parameters m and zi in m-th order grinding kinetics were analyzed by the partial-derivative method and the critical time tc(tc = exp (1/ zi)) was obtained. zi mainly affected the breakage rate when t < tc; otherwise, m mainly affected the breakage rate. In these tests, tc was considerably higher than the grinding times, and HPGR products yielded a higher zi-value than the CC product for the same sieve size. This indicated that HPGR products had a higher breakage rate and needed a shorter grinding time for a certain grinding fineness. Et was calculated by simulating the size distributions of batch grinding products. HPGR products gave a lower Et at a decreasing rate than the CC products for -2.0 mm feed and -0.5mm feed, and then showed a slightly higher Et for -2.0+0.5 mm feed. This indicated that overginding in HPGR full-size products was more serious under the condition of coarse grinding, whereas the efficiency was higher and overgrinding weakened significantly in HPGR coarse products because of screening-out fines. Based on the above research, a new process of “ultra-crushing in HPGR – classified grinding” was advanced, reducing ores tonnage into first stage ball mill significantly, improving grinding efficient and weakening overgrinding in the whole grinding process.INTRODUCTIONIn mineral processing, comminution accounts for a substantial portion (approximately 60~70%) of the energy consumed in plants. As an ultra-fine crushing equipment,the application of the HPGR for industrial comminution has been paid close attention because of its low specific energy, low steel consumption, high capacity and high ratio of reduction, among others (Schonert, 1998; Norgate & Weller, 1994; Fuerstenau & Kapur, 1995). HPGRs comprise two counter-rotating rolls that draw feed material into the roll gap. One roll is fixed to the mainframe, while the other movable roll is mounted on slides and positioned by hydraulic rams. The specific pressing force (SPF) (i.e., total force divided by projected roller area) is typically in the range of 3~9 N/mm2 depending on the application, while pressures of up to 1000 N/mm2 have been measured within the operating gap (Maxton , Morley, & Bearman , 2003)."

Jan 1, 2016

By Rainer Antretter

"THE CHALLENGE The 14km long, Arlbergtunnel, closed for public traffic during summer 2015, receiving a comprehensive and substantial renovation from 2015 to 2017. The main works discussed here, carried out during 2015, comprise 37 drill and blast SEM/NATM emergency escape tunnels from road level to the ventilation duct plenum have to be constructed as well as eight additional lay-by niches and three transformer tunnels. This presentation comprises the construction ventilation design, designed according to national regulations, suitable for 150 employees working 24/7 simultaneously at more than 40 single working sites lined up along the tunnel. The ventilation-system chosen was utilising two existing shafts for intake/discharge and a cross passage to surface, to handle a total fan power of 1.600kW. DESCRIPTION OF RENOVATION WORKS Linking Tyrol and Vorarlberg, two Federal States of Austria, the Arlbergtunnel is a single tube two-way road tunnel with vent duct plenum, constructed in the mid-1970s. According to latest EU legislation, additional escape exits have become obligatory. The existing seven cross passage links to the adjacent Arlberg Railway Tunnel, with average spacing of about 1.500m constructed in 2007, an additional upgrade to shorter escape spaces of approx. 400m was now required to comply with the updated legislation. Additional transformer tunnels, lay-by niches and small niches for emergency maintenance use, cleaning and other purposes, as well as a the installation of a new fire main in the invert, coupled with the simultaneous replacement of virtually the entire power and signaling cables, generated several dozen small and large single sites distributed along the 14km of tunnel.Purpose of the 37 walkable emergency escape tunnels is to reach the “upper deck” of the Arlbergtunnel, the vent duct plenum. These have an 180deg curve in plan, inclined at 10% and approx. 60m (65yd) long tunnels, excavated using drill and blast method starting from road level and working upwards to the level of an “intermediate soffit”, the vent duct plenum in the crown of the tunnel. The vent duct plenum is separated into a fresh air part and an exhaust air part, shown in Figure 1. The escape tunnels end with a pressure door in the fresh air section of the ventilation duct plenum. From there illuminated signs show the shortest escape route to the safe area between the road tunnel and the railway tunnel, as shown in Figure 2."

Jan 1, 2016

By M. Raffaldi, J. Johnson, M. Stepan, D. Benton

"The Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD), is continuing its High-Energy High-Displacement (HEHD) testing of field-scale shotcrete panels. A test program was developed to determine the relationship between applied force, displacement, and energy for both unreinforced and reinforced shotcrete panels. Reinforcement options consisted of synthetic macro-fibers, sprayed polyurea liners, chain-link fence, welded-wire mesh, and combinations of these products. During testing, photogrammetry was used to measure the geometric changes of the panels, including volume changes and panel cracking. These measurements were correlated with the load and displacement data, allowing visual observation to be related to the applied force and displacement. The test results provide a comparison of the mechanical performance of the various panel types and can be used by the practicing engineer to evaluate installed support based on visual observation of cracking and deformation. Visual assessment of the loading cycle and strength capacity of shotcrete in underground excavations will improve mine safety by providing a means to quantify the stability of installed shotcrete support. INTRODUCTION The National Institute for Occupational Safety and Health (NIOSH), Office of Mine Safety and Health Research (OMSHR), Spokane Mining Research Division (SMRD) is continuing research on the behavior of shotcrete when used as the surface support component in mining ground support systems. Ground control safety often depends on supporting, or at least containing, the ground between the rockbolts. Shotcrete and mesh, in various combinations and with other components, are often used to accomplish this (see Figure 1). Maintaining support pressure during ground deformation is key to the performance of these systems, and to ensuring miner safety. However, the toughness of a ground support system–the ability to maintain strength over large deformations–is difficult to quantify. Researchers at SMRD have responded to this deficiency by designing a full-scale test device, described previously by Martin et al. [2015a], and beginning a testing program to assess the behavior of shotcrete surface support reinforced with a variety of products including: fibers, chain-link mesh, welded-wire mesh, spray-on polyurea liners, and combinations of these products. This paper presents the findings of these tests."

Jan 1, 2016

By Christoph Schulte-Schrepping, Bou-Young Youn, Rolf Breitenbücher

"The main requirements of two-component grouts are a high workability and sufficient stability against sedimentation with a retention time of more than 72 hours, as well as a rapid strength development im-mediately after grouting. Component A usually consists of OPC, water, bentonite, and retarding agent. Component B, a liquid accelerator, is added to Component A during grouting at the end of the shield tail. Current investigations on different compositions of Component A showed a high workability lasting for at least 72 hours. The workability could be extended with increasing amount of the retarding agent to a certain degree. An increase of the bentonite content improved the stability of the mix, but had a negative impact on the flowability respectively the workability of Component A. High compressive strengths could be rather achieved by an adapted mixing ratio of Component A and B than by increasing the amount of the accelerator. Thereby, the interactions and compatibility of the selected constituents play an essential role. INTRODUCTION In mechanized tunneling with segment linings, the annular gap between segment ring and soil must be filled instantaneously with an adequate grouting mortar. The main functions of the annular gap grouting are to stabilize the tunnel lining and to minimize settlements of the ground surface at the same time. Thereby, two contradictory requirements are demanded on annular gap grouts: On the one hand a high workability and sufficient stability against sedimentation, on the other hand a rapid strength develop-ment immediately after grouting. Besides single-component grouts, which achieve the necessary stiffen-ing by dewatering into the surrounding soil, two-component grouts are used, especially in cohesive soils with a very low permeability. Basically, annular gap grouts are almost exclusively defined on empirical basis. Fundamental studies about the constituents and composition of the grout as well as the related achievable properties are still missing so far. Therefore, it is necessary to investigate the material-specific correlations regarding the relevant parameters of annular gap grouts – workability and flowability, stability of the mix as well as strength development – in comprehensive experiments. Based on the knowledge gained from the investigations, it should also be possible, to perform the grouting material according to a real design concept and thus, to ensure an adequate grouting in prac-tice considering the geological and hydro-geological conditions."

Jan 1, 2016

By M. Maccagni, J. Nielsen

"Engitec developed the EZINEX® Technology some years ago to recover zinc from oxidized secondary sources. This process works at neutral pH and can take into solution any kind of metal, but iron is rejected and remains in the leach residue. Engitec has also developed the FLUOBORATE System, which is able to recover lead and copper from relevant concentrates. Some iron is leached into solution, but it is controlled through a solution purification bleed treatment. In this paper, we present the two above mentioned technologies. They are very different with regards to the chemical environments and the methods used to control the build-up of iron in solution, but both systems are suitable to treat iron bearing feeds.INTRODUCTIONIn the design of hydrometallurgical processes, the most important issues are the water balance, the filtration and the control of impurities. This is particularly important when the process includes an electrowinning unit. Iron has been one of the most problematic elements to remove, especially in acidic environments.Engitec Technologies has developed several hydrometallurgical processes divided in two different electrolyte lines: the Fluoborate Technology for the recovery of lead and copper from primary and secondary sources and the Ammonium Chloride System based on a chloride electrolyte for the recovery of different non-ferrous metals, among which zinc and lead are the most important. In both cases, iron is present in the feed and needs to be eliminated from the solution. It is not a problem for the quality of the metal produced, but when present in solution, it consumes the basic electrolyte reducing its free concentration which is very important both for both the leaching and electrowinning unit operations. Both process systems are very peculiar, the fluoborate case being much more intriguing."

Jan 1, 2016

By Verya Nasri, Kevin Akbarpour, Hiva Mahdavi

"The Sheppard East Light Rail Transit (SELRT) project comprises approximately 13 km of new light rail, which will be constructed along Sheppard Avenue East in Toronto. There is a 380 metre long section of the route that will be constructed as tunnel below Highway 404, which is owned by the Ministry of Transportation Ontario (MTO). MTO has published guidelines for tunneling under its highways. An impact analysis was undertaken to predict the surface settlement and angular distortion of Highway 404 resulting from the construction of the twin tunnels. The results were then compared to the performance criteria defined in MTO’s guidelines. As a result of this analysis, it was necessary to request an adjustment to MTO’s current performance criteria. This paper presents details and results of the impact assessment, approaches taken to satisfy the requirements defined by MTO, and provides details of the adjustment permitted by MTO. INTRODUCTION Several major rapid transit projects are planned for the Greater Toronto and Hamilton Area (GTHA) located in southern Ontario, Canada. These projects are part of The Big Move (Metrolinx 2008) initiative, a 25-year, and $50 billion plan aimed at improving regional transportation. Metrolinx, an agency of the Government of Ontario, is now working collaboratively across the region to deliver major Toronto rapid transit projects to the GTHA. One such project is the SELRT. The line will largely run along Sheppard Avenue East on the surface, except for a crossing of Highway 404 where it will be constructed using a combination of open cut and bored tunneling methods. AECOM has been retained by Metrolinx as the Technical Advisor (TA) to develop the Reference Conceptual Design (RCD) and Project Specific Output Specifications (PSOS) for the project. Also, Infrastructure Ontario (IO) is the Co-Sponsor and CH2M HILL is Metrolinx’s Owner’s Engineer (OE) & Project Management Support (PMS) for the new LRT lines. This paper presents information on the tunneling settlement analysis and further work undertaken to satisfy the MTO’s requirements."

Jan 1, 2016

By L. J. Bryson, C. A. Biley

"Anglo American Platinum’s Rustenburg Base Metals Refiners (RBMR) produces Ni and Cu cathode from slow cooled converter matte after Platinum Group Metals (PGMs) are magnetically separated for further processing. In 2010, execution of the RBMR expansion project was commenced to increase the production capacity to 33 ktpa Ni. The expansion, which is currently still in a ramp-up stage, brought about several fundamental changes to the circuit chemistry, including the installation of a dedicated Pressure Iron Removal (PIR) autoclave. This provided an independent outlet for iron from the refinery, which previously deported to the residue from the leach circuit and was toll refined. At the same time as changes in the circuit associated with the RBMR expansion were being made, the plant experienced a significant increase in iron and copper units per nickel unit in the feed. The decoupling of the leaching and iron removal process steps has had significant advantages for the robustness and control of the overall circuit, in particular pertaining to the preparation of a nickel electrolyte of sufficient purity to produce LME grade nickel. This paper details the primary changes to the RBMR circuit chemistry with a particular focus on iron deportment and the benefits derived from the installation of the PIR autoclave.INTRODUCTIONAnglo American Platinum mines and refines Platinum Group Metals (PGMs) through a complex processing pipeline in its South African operations. Mined ore is first treated through several mineral processing stages, geared to the recovery of base metals and associated PGMs, followed by smelting and refining operations that aim to separate base metals from PGMs and recover the value components to purified, saleable products. The focus of this paper is the Rustenburg Base Metals Refiners (RBMR) complex which receives a PGM-containing converter matte, then physically separates PGMs and base metals, and recovers nickel and copper to cathode by utilising leaching, precipitation and electrowinning processes.With new mining operations coming online and the continued increase in PGM ore arisings, it was necessary to undertake an expansion project at the Base Metal Refinery (BMR) to increase production capacity from 21 ktpa to 33 ktpa Ni. Complicating the expansion project was the requirement of continued production through all stages of design, construction and implementation and, due to stringent capital constraints, the utilisation of all existing equipment installed during a previous expansion in 1981. Against this backdrop, the expanded BMR flow sheet involved significant changes to the chemistry, especially iron management. These changes in iron management allowed for the separation of iron and copper residues and significantly increased the robustness of the plant to changes in feed mineralogy as well as the potential to increase production duties of the existing equipment."

Jan 1, 2016

By C. Birch

"A mineral resource royalty is payment to the holder of mineral rights for the utilization of the mineral resource. In South Africa, this payment is made to the State as holder of the mineral rights (The Mineral and Petroleum Resources Royalty Act of 2008). The principle purpose of this research paper is to identify if the State is benefitting from the mineral resource royalty by considering its impact on seven individual Witwatersrand gold mines.For this study, a simple financial optimiser model was created in Microsoft Excel that links the ore flow, block listing and the cash flow (excluding or including the cost of the mineral resource royalty). Mixed integer linear programing (the Excel Solver function) is utilised to optimise either profit or NPV (at 9% and 12%) by adjusting the cut-off grade.The impact on each of the seven mines mine was different but overall R7.9 billion is estimated to be paid in mineral resource royalty over their expected remaining lives. Due to the cost of the mineral resource royalty and increasing the cut-off grades, the total revenue decreases by R10 billion. A significant portion of this lost revenue would have been paid to the State in the forms of other taxation including company income tax which decreases by R2.8 billion. It is recommended that an industry wide investigation be conducted to determine if the resource royalty is adding to the State’s revenue, or destroying value including premature job losses. IntroductionTaxation of mining companies has become a very topical subject in the context of the postapartheid South African economy. There have been increasing calls for equitable re-distribution of mineral asset wealth for the benefit of all South African citizens and not just to an elite few. As part of the Mineral and Petroleum Resources Development Act (MRDPA) of 2002, the Mineral and Petroleum Resources Royalty Act of 2008 was introduced and came into effect in 2010 (South African Revenue Services, 2008). A mineral royalty is payment to the holder of mineral rights for the utilization of the mineral resource. In the case where the holder of the mineral right is the State, then this payment is made to the State (Cawood, 1999). Studies on the potential impact of the mineral resource royalty on the minerals industry have been conducted during the formulation of the Act and subesquently. These include Cawood and Macfarlane (2003), who suggested a cap of no more than 3% (Cawood and Macfarlane, 2003), as well as Cawood (2011), who predicted rising cut-off grades and thus reducing mineral reserves. In 2013, Grobler completed a Masters in the Faculty of Economic and Management Sciences at the University of Pretoria and concluded that the impact of the mineral resource royalty on the economy is positive. She stated that the royalty has caused operating expenses to increase, but this does not appear to be significant. Furthermore, she stated that the royalty has not affected the way the mining industry operates (Grobler, 2014)."

Jan 1, 2016

By Elbasher M. E. Ahmed, Indresan Govender

"A mechanistic model of axial charge segregation in rotating drums is presented. We show that granular material composed of different frictional properties diffuse into axial bands as a consequence of concentration fluctuations in the free surface layer that is caused by friction-limited mobility. A Bagnoldian stress assumption ensures an asymmetric free surface profile thereby providing the essential ingredients for the evolution of axial bands and the subsequent band coarsening observed in the literature. The formulation is sensitive to the boundary conditions of tumbling mills, including particle size and density, mill speed, inter-particle bulk friction, end wall friction and drum geometry (length and diameter).INTRODUCTIONA mechanism to fully describe the axial segregation of charge in a rotating drum remains elusive to the mineral processing industry. With regard to low aspect ratio mills (like ball mills), current thinking favours the use of closed circuit mills with correspondingly low residence times to offset the completely random contact probabilities between particles and balls (Wills & Napier-Munn, 2006). Conical end caps are argued to exploit the centrifugal force to achieve a regular gradation of ball size along the mill with larger sizes at the feed end and smaller ones closer to the discharge. However; segregation along the length has been observed in the absence of conical end caps (Oyama, 1939; Levine, 1999): In these investigations, sufficient differences in the particle’s mechanical properties (particle size, density, shape, surface roughness) was enough to successfully achieve axial segregation. Figure 1 shows the segregation of a bimodal distribution (by size) into bands of larger (darker colour) and smaller (lighter colour) particles."

Jan 1, 2016