Search Documents

By Benno Ring

"When designing segmental lining at a cross passage, modern solutions try to bear the loads transferred around the opening within the rings by using shear elements in the ring joints. Commonly used shear systems providing coupling are cam & pocket, shear keys, bicones and steel dowels. These solutions have advantages and disadvantages, but most importantly they have limits in their capacity to stabilize the lining at cross passages. With the help of 3D-FE-analyses for an opening of one segmental ring these different solutions are compared taking various ground conditions into account. As a result the capacity of the individual system is determined. Notice is made regarding the applicability of the system as well as the consequences for the design and the verification. INTRODUCTION The design of the lining at a cross passage is among the most difficult tasks when designing TBM-tunnels. At one time the bedding of the lining disappears due to the excavation behind the lining, at another the ring-structure is interrupted when parts of the lining are removed for the opening. The trick is to transfer the loads around the opening into other segments and to areas of the lining which are still supported by the ground. In the rings immediately at the cross passage this creates a distribution of forces within the segments that strongly deviates from that of the regular lining. The design needs to consider the boundary conditions of the respectively chosen solution for stiffening of the opening and its peculiarities in the modeling as well as in the verifications. In the past segments of steel or an internal strutting of steel (DAUB 2013) placed around the later openings were commonly used, see Figure 1. The application of a strutting from the outside to the rings is restricted to such circumstances when for example a connection from a shaft to the tunnel can be made in suitable ground conditions (Ring and Glomp 2012). Though steel segments provide a robust solution, they are expensive due to their laborious manufacture, the high proportion of construction steel required and the time consuming installation in the tunnel (Häfliger 2013). A strutting of steel requires extensive design and verification. The resulting structure usually weighs several tons and must be erected as well as demounted within the confined space of the tunnel, requiring suitable transport and assembly equipment. The cross section remains restricted, thus causing a bottleneck for TBM operations and hindering the works and installations for the cross passage works."

Jan 1, 2016

By William G. Pariseau, Michael K. McCarter

"The challenge of estimating mine-wide subsidence and linkages to seismicity over tabular deposits is addressed by a special finite element technique (dual node - dual mesh). Subsidence and mine-induced seismicity begins near the face when caving occurs and propagates to the surface as extraction reaches a critical extent. Thus, the challenge is to obtain details at the face at the meter scale and also at the surface over the whole mine at the kilometer scale. Interactions between old and new sections of a mine are automatically taken into account with this technique. The finite element method is well established technology based on fundamentals of physical laws, kinematics and material laws. With this technique, no empirical ""scaling"" or fitting computer output by input data ""adjustment"" to mine measurements is necessary. Capability is demonstrated for doing practical whole-mine subsidence analysis from first principles. Mine-induced seismicity is shown to correlate well with face advance and element failure.INTRODUCTIONSeismicity associated with coal mining has been under study for several years by a team at the University of Utah. Team members include mining faculty, research geophysicists and students from the Departments of Mining Engineering and Geology & Geophysics. Mines in central Utah that have been studied include the Trail Mountain Mine (Pariseau, 2015; Pariseau and McCarter, 2015), the Beehive Mine, also known as the Des-BeeDove (Pariseau, 2014), and the Crandall Canyon Mine (Pariseau, 2015). These mines were developed from outcrops in the Wasatch Plateau coal field west of Price, Utah, where the topography is characterized by . steeply incised canyon drainages and high plateaus with relief of a thousand meters or so.Seismicity associated with coal mining in central Utah has been of interest for many years and includes studies in the Book Cliffs to the east of Price, Utah, where mining is still active (Smith et al, 1974; Agapito, Goodrich and Moon, 1997; Arabasz et al, 2001; Arabasz et al, 2002; Fletcher and McGarr, 2005; McGarr and Fletcher 2005; Maleki, 2005) and to the northwest (Ellenberger et al, 2001). Results of many micro-seismic studies are summarized perhaps best by lannacchione, et al (2005) in stating, ""Deviations from normal strata response can provide useful stability information.""This study concerns a fourth underground coal mine in the southern portion of the Wasatch Plateau coalfield, hereafter referred to as the MINE. Focus is on mining from 2004-2008 with the objective of examining mining in relation to seismicity."

Jan 1, 2016

By Georgios Kalamaras, Sebastiano Pelizza, Carlo Alessio

"This article describes, through the presentation of five cases-history, technological advances that the Authors together with Tunneling Contractors devised for coping with adverse geotechnical conditions. It is believed that by introducing these new elements in a method that has proven its value in Italy and abroad for the last 40 years, the umbrella arch method, due to its versatility and simplicity, can become a universal method for conventional tunneling in very poor ground conditions. After a description of common faults and mistakes in applying the method, 5 projects are presented which demonstrate that self-drilling pipes give excellent results in terms of performance a zero volume loss, while, function of the ground conditions the various grouting mixtures used, such as expansive jet-injected cement-base grouts and bi-component resins, extend the use of the umbrella-arch in variety of grounds even in presence of water-bearing lenses. The case-histories provide successful applications in different conditions.BASIC FEATURES OF UMBRELLA ARCH METHODThe umbrella arch method provides a short support of the tunnel vault just ahead of the excavation face. The method foresees the drilling and installation of peripheral, sub-horizontal steel pipes in the ground, followed by their grouting. The umbrella arch method is also known as forepoling, steel pipe umbrella, reinforced protective umbrella or simply “umbrella”. The umbrella arch method does not have a static function because the immediate stabilization of tunnel section is entrusted to the internal shell of steel ribs and shotcrete. The “umbrella” provides a pre-support of the excavation which has to be stable for an adequate length and duration permitting the installation of the next steel rib and shotcrete under conditions of safety (Figure 1).The umbrella-arch provides pre-reinforcement of poor ground around the tunnel perimeter in a simple and flexible manner that is adaptable to different ground conditions. In fact, it is possible to vary the number and length of pipes, the distance between them, their diameter and thickness as well as the overlapping length of two succeeding umbrella arches. The versatility of the umbrella arch technique allows its application to: clay deposits, granular alluvial deposits, moraine and debris materials even when containing large blocks, heavily jointed, foliated and tectonically disturbed rock masses."

Jan 1, 2016

By Ingo Ossenbühl, Wolfgang Dolsak, Vojtech Gall, Axel G. Nitschke

"Yielding support systems for application in underground construction have a long history, primarily in mining. Typical examples are tunnels subject to loading conditions that lead to overstressing of the newly installed support or existing tunnel structures in active fault zones. Recent applications for tunnel rehabilitation projects unveiled the capabilities and flexibility of combined yielding support systems presented in this paper. Frequently, the main requirements for tunnel rehabilitation applications are a fast, safe, and simple installation along with the need for flexibility with regards to existing tunnel geometries. A combined support system consisting of steel sets with yielding connections and special groutable hoses has proven to be an efficient support measure providing a multitude of advantages compared to conventional rehabilitation approaches. The presented yielding support system provides an immediate and active support, while it allows for controlled yielding upon experiencing loads beyond its support capacity. INTRODUCTION The excavation of underground spaces leads to redistribution in the existing stress regime. This load redistribution goes along with deformations in the surrounding rock mass. Magnitude and duration of these deformations depend on the tunnel’s depth and geological conditions, but also on the installed support system. Modern civil tunneling infrastructure has generally an envisioned service life of about 120 years. Conventional tunneling provides typically a dual support system, split into the initial (or primary) and final (or secondary) lining. A typical design principle in civil tunneling is to let the vast majority of deformations acting on the initial lining cease, before the final lining is installed. Based on this approach, the loading on the final lining is significantly reduced and signs of overstressing, such as cracking of the lining, are typically limited to the initial lining. However, special cases in swelling and squeezing ground require different approaches, including yielding support systems."

Jan 1, 2016

By J. F. Brune

"Re-occurring face ignitions in U.S. coal mines are concerning and require a closer look at air quality monitoring systems and practices employed in these mines. The explosion disaster at the Upper Big Branch mine in West Virginia in 2010 caused 29 fatal injuries and was largely caused by inadequate water sprays and inadequate ventilation monitoring. In this comparison, the author compares ventilation system monitoring in Australian, German and U.S. underground coal mines and makes recommendations for improvements and best practices. Mines in Germany and Australia are adhering to more stringent requirements for monitoring air quality and quantity and for monitoring water spray systems on cutters to prevent frictional ignitions. Air quality should to be monitored for sufficient oxygen, toxic gases, explosibility and for fire gases indicating a potential fire. Ventilation monitors must also confirm that sufficient quantities of air are available. Fully automated, continuously recording atmospheric monitoring and alarm systems are established practices in Germany and Australia and should be mandated for U.S. mines as well, in addition to the current, regular spot inspections of the ventilation system by certified mine examiners. BACKGROUND: METHANE EXPLOSIONS, FACE IGNITIONS AND NEED FOR AIR QUALITY MONITORING Accumulations of methane in face areas of underground coal mines frequently lead to ignitions that can cause burns, traumatic injuries and, in the case of the 2010 Upper Big Branch disaster, cause major explosions with multiple fatalities. Table 1 shows the number of reported face ignitions in U.S. coal mines between 2010 and 2014, based on statistical data published by MSHA (MSHA 2010 – 2014). Although there appears to be a downward trend in such ignition incidents over time, ignitions continue to occur with some regularity; and each ignition may cause a potentially catastrophic mine explosion.Per regulation, all U.S. coal mining machinery, continuous miners and longwall equipment, is outfitted with continuously monitoring methane sensors wired to cut power to the equipment as the methane level exceeds 1%. Face ignitions keep occurring because these sensors are usually not positioned in sufficiently close proximity to the coal cutting drums or to the freshly exposed coal face where the methane is most likely released. Therefore, methane may accumulate in explosive concentrations near the coal face and the cutting drums long before the gas concentration reaches the 1% level near the monitor and creates an alarm."

Jan 1, 2016

By Emanuele Catelli, Paolo Vicentini, Manuel Petitat, Paolo Lanfranchi

"More than 800 million tons of material will be excavated during large underground projects such as tunnels, undergrounds and power plants by 2030 in Europe only. The raw material excavated is often classified as waste, which involves environmental impact and transport issues: landfill areas, CO2 emissions and noise. But how can such massive amounts of material be transported, processed and deposited? Using the example of the AlpTransit Ceneri Base Tunnel (15.4 km), we show that suitable excavated materials can be used sustainably as a primary resource for tunnel concrete. This requires careful planning of the installations and storage areas by the client, timely building of the processing plants and other handling facilities outside the tunnel and a continuous evaluation of the raw material quality. 1. INTRODUCTION Spoil management is a central element of large construction projects. The systematic reuse of suitable excavated material not only saves natural resources, reduces transport distances and landfill volume, but can also decrease overall construction costs. Ideally, all of the concrete needed for tunnel lining can be produced with this on-site material. Such a natural resource management concept was applied for the construction of the new Gotthard Base Tunnel (L = 57 km). Spoil management concepts are, how-ever, difficult to implement and call for innovative techniques, sophisticated logistics and organization. In the context of large projects, environmentally friendly transport, processing and storage of millions of tons of excavated loose material represent another logistics challenge (Simmen & Lieb, 2010). This paper shows key factors that led to the successful completion of spoil management at the Ceneri Base Tunnel, which constitutes a part of the AlpTransit Gotthard Project (Figure 1)."

Jan 1, 2016

By S. G. Britton

"INTRODUCTION Strategies to improve performance in mining production, maintenance and mineral processing operations has evolved over time from straightforward time studies of individual machine performance in the 1960’s-1970’s to more sophisticated and better focused statistical and financial tools that have emerged in the 1980’s-1990’s . These newer strategies fall under the broad descriptive category of “Operational Excellence”. Operational Excellence is the term that embodies a number of performance evaluating strategies, the most popular and relevant to mining includes the following: • Six sigma for addressing errors within mining or milling process and work standards • Lean manufacturing to optimize organizational and operational performance through continuous improvement. There are other strategies that can be applied as well and this paper is not focused on a review of the pros and cons of any one strategy. However, the common threads in these strategies embody the expectation that expected results from these efforts can be quantified and that value will positively benefit the targeted work process, organizational unit, equipment deployment or time schedule when applied to it as part of continuous improvement efforts. The priority for proceeding with any one or more of these efforts is based on the calculated net value of the required resources to affect the change versus the estimated value gained. The practice is identified as the value mapping process. This discussion summarizes the value mapping process methodology used at a mature uranium mine and mill in northern Canada to work through the myriad of potential improvement efforts available through the operational excellence process for continuous improvement.THE RABBIT LAKE MINE AND MILL The Rabbit Lake Mine and Mill are located in northern Saskatchewan, Canada on the shores of Wollaston Lake (Figure 1).The mine was discovered in the mid-1960s and was built by Gulf Minerals, Ltd. The mill began processing uranium ore into yellowcake in 1975 from an adjacent open pit mine. A whole ore acid leaching followed by solvent extraction and precipitation forms the basic milling processes. The operation continued to produce yellowcake through a succession of open pits and finally opened an underground mine in the early 1990s. Since beginning production, over 200 million pounds of yellowcake has been packaged from the site, making it the sixth highest producing uranium mine of all time."

Jan 1, 2016

By J. F. Brune, A. Verma

"Face ignitions in underground coal mines are a major risk for underground mining operations, as they can lead to methane or coal dust explosions. The 2010 disaster at the Upper Big Branch Mine resulted in 29 fatalities due to a methane and coal dust explosion initiated from a face ignition. Much research has been conducted to mitigate face ignition hazards, from water sprays to installing passive and active explosion barriers. Despite the increased use of water sprays in U.S. coal mines, there have been more than 50 documented face ignitions in the U.S. underground coal mines since 2010, indicating that this hazard still prevails. This paper will examine the statistics of face ignitions and gas explosion in U.S. coal mines based on MSHA data. It will study factors contributing to these face ignitions and outline best practices for their prevention based on experience and practices worldwide. INTRODUCTION Methane and coal dust explosions are one of the major causes of coal mine disasters in the U.S. and around the world. Such disasters have resulted in the large number of fatalities and loss of mine infrastructure. The recent explosion at the Soma coal mine in Turkey has caused the death of 301 miners (Mining Turkey, 2014). As documented by U.S. Mine Safety and Health Administration (MSHA, 2015a), the U.S. coal mining industry has also experienced several catastrophic mine explosions with accidents at Upper Big Branch mine, Darby mine, Sago mine and Jim Walter Resources No. 5 mine in the last decade, causing the deaths of almost 60 miners. Every explosion requires a source of ignition, the right amount of fuel and oxygen. In underground coal mines, methane acts as a fuel while ventilation air acts as a source of oxygen. The source of ignition may vary from spontaneous combustion, electrical equipment and switchgear, mechanical heat sources, face ignitions due to friction rock-on-rock or from cutter bits and lightning strikes. Under the right conditions, energy of less than 0.3 mJ is sufficient to ignite methane-air mixtures (James, 2007) that can result in a catastrophic explosion. Much research has been done to mitigate the methane explosion hazard by proper dilution, continuous monitoring of methane and elimination of ignition sources. Historical studies indicate that face ignitions are the major cause of explosion in underground coal mining operations worldwide (Belle, Carey, and Robertson, 2012). Statistics shows that most mine disasters were started from a small face ignition, which turned into a major explosion fueled by additional methane and coal dust (Belle et al., 2012). To investigate face ignition hazards, researchers must study potential ignition sources as well as potential explosive atmospheres near mechanical coal cutting operations. Statistical analysis of U.S. coal mine face ignitions reported by the U.S. Mine Safety and Health Administration (MSHA, 2015b) shows that several factors are responsible for face ignitions."

Jan 1, 2016

By Chi Zhang, Junyi Wu

"The use of permanent stainless steel cathodes for electrorefining and electrowinning of cathode copper had been introduced to the market long time ago and now is a well-accepted technology worldwide. During the last decades, the Chinese copper refinery industry had been growing rapidly and many large scaled production plants had been built. In the modern refineries, permanent stainless steel cathodes are introduced and used instead of traditional starter sheets. The most common steel grade used is austenitic stainless steel S31603 (316L/1.4404), while both S30403 (304L/1.4404) and N08904 (904L/1.4539) have been used depending on the actual working conditions, especially with regarding corrosion environment. While 316L permanent cathode functions well in many plants, different kind of problems, such corrosion and deformation, have been reported. There is therefore an increased need for more suitable material. New stainless steels, such as duplex stainless steels, with better properties have been tried and introduced into the application of permanent stainless steel cathode with satisfied results. The article introduces first the Chinese copper refinery industry and properties of duplex stainless steel in general, and then describes the development of using permanent duplex stainless steel cathode, including the actual working conditions, production of cathode sheets as well as the experiences of application in details. After more than one year’s usage, the advantages of permanent duplex stainless steel cathodes are clear seen.INTRODUCTIONChina has become a major player in the international copper market, accounting for around 40 percent of global refined copper demand. Despite the slowdown of the Chinese economy, the consumption of copper products will still increase, but with a medium and/or low growth which will be the new situation for the coming years. The average growth rate is expected to be around 5 percent per annual. In the coming Five-Year plan for National Economic and Social Development a number of initiatives will be finalized which will require massive amounts of copper. In 2015, the expected consumption of copper products will be over 9 million metric tons. The main driver of the consumption is the electric power industry which accounts nearly the half of the total consumption; followed by cooling application with 15% and transportation with nearly 10%, see figure 1."

Jan 1, 2016

By P. Ramirez

"To achieve an optimal metallurgical performance in the flotation process the bubble diameter should be between 0.5 and 2.5 mm. To control bubble size, frothers are added, reducing bubble size and conferring bubble stability against coalescence. However, the bubble generation mechanism determines predominantly the bubble size distribution produced. In mechanical flotation cells, bubbles are produced by the shear stress generated by a rotating blade on a gas stream. This mechanism produces a log normal bubble size distribution. In contrast, in column flotation, jetting gas injectors are commonly used in Chile and the bubble size distribution is bimodal with small and large bubbles. Bubbles larger than 2.5 mm mean a loss in surface area, while bubbles smaller than 0.5 mm move with the pulp stream and therefore collide less frequently with particles. In this paper, a new device based on a jetting sparger and a deflector disc (impinging jetting) is evaluated as an alternative sparger for column flotation.The new device was tested in a rectangular acrylic cell 1 m × 0.5 m × 3 m. High-speed cinematography was used to compare bubble generation with jetting and impinging jetting at different gas velocity in the nozzle (5–50 m/s). From the image analysis, it was observed that the deflector induces a shear stress, in analogy to a rotating blade but in this case the shear results from a high velocity gas hitting a static surface. The device was evaluated in a 0.5 m diameter 3 m high column. The McGill bubble viewer technique was used to compare the bubble size generated by jetting and impinging jetting. It was found that the Sauter mean bubble diameter reduced from 7.4 mm to 2.8 mm, when the jetting sparger was modified with the deflector. In the case of the impinging jetting sparger, 70% of the bubbles were in the effective range for flotation, while for the jetting sparger, only 10% were in the effective range."

Jan 1, 2016

By A. Singh

"The flotation of fine minerals less than 10 µm in size is an age old challenge spanning both the precious metal and industrial mineral sectors across a range of commodities. This problem has been brought into sharper focus by the emergence of the practice of fine grinding of flotation feed to effect better liberation of the targeted minerals. However, the ability of conventional flotation cells to effectively float the liberated fines remains questionable. In order to overcome this problem, Gold Ore postulates the “Bringing the Mountain to Mohamed” hypothesis which comprises the steps of gas nucleation on particle surfaces, aggregation of particles and levitation of aggregates. Testing of this hypothesis at Mintek, South Africa, showed a ~180% increase in the Kelsall kfast factor coupled with a projected recovery improvement of ~4 % for the Mach Reactor case coupled with a final concentrate grade of ~2 times that of conventional flotation. These fundamentals were then extrapolated to plant scale with Mach Reactors installed on the flotation feed at Platmin’s Tailings Scavenger Plant (TSP) with the objective of scavenging the fine minerals lost to tailings by the main plant. This paper details the theory, pilot plant results as well as key aspects of the full scale plant design supplemented by operational plant observations after commissioning. This game changing application is regarded as being pivotal to future flotation plant design whilst providing the technology leverage required for the survival of mineral operations in an economically unfriendly environment.INTRODUCTION - THE CONUNDRUM OF FINE PARTICLE FLOTATION“If the mountain won't come to Mohamed then Mohamed must go to the mountain” is an age old saying written into the book of proverbs in 1670. Legend has it that Mohamed promised his people that he would summon a mountain to come over to him so that he could offer up his prayers from its summit. After numerous attempts at moving the mountain went in vain, Mohamed, quite unabashed, said “Well if the mountain will not come to Mohamed, then Mohamed will go to the Mountain.” In this analogy, Mohamed is a fine particle <10 µm and the mountain is a bubble within a flotation system. The age old challenge is how to bring these two together to achieve attachment?"

Jan 1, 2016

By Matthew Anderson, David Day, Paul Smith

"The Midwest is presently the focus for Combined Sewer Overflow (CSO) abatement in the United States (U.S.). Most of the EPA mandated utility and municipal long term CSO abatement programs in large metro areas in the Midwest such as Cleveland, Indianapolis, Columbus, Chicago, St Louis, Akron, Fort Wayne, Louisville, Kansas City, Omaha and Pittsburg use or will use deep tunnels for storage and conveyance of CSOs. This paper will compare design methods specified and implemented for tunnel construction in Midwestern geology such as soft ground and mixed face EPBM tunnels, hard rock TBM tunnels, drill & blast tunnels, road header tunnels along with tunnel lining systems. It will also review the performance of successful CSO systems that include design life cycle, vortex and drop shaft configurations, pump stations, storage and conveyance strategies and long term operation and maintenance criteria. HISTORY and BACKGROUND Prior to development of mandated wastewater treatment plants, collecting both wastewater and storm water runoff in a single-pipe system was an efficient and economical solution. The early combined sewer systems were typically designed and sized to carry several times the average dry weather wastewater flows and not designed to handle a mixed volume of waste water and storm water during a wet weather event. Beginning in the early 1970s, federal legislation (Clean Water Act of 1972, Clean Water Act of 1977 and the Water Quality Act of 1982) changed how municipalities and industries in the U.S. were required to treat and discharge wastewater into the nation’s surface waters. They were mandated to treat wastewater at federal regulatory standards for discharge into surface waters that is safe for humans, wildlife and aquatic life. The wastewater treatment facilities that evolved were initially designed and sized to treat only the peak volume of raw wastewater flowing during dry weather. Combined sewer system control sections or relief structures were installed upstream of wastewater treatment plants (WWTP) and were designed to protect WWTPs from potential damage that would be caused if peak volumes of raw wastewater mixed with storm water runoff reached and overwhelmed the WWTPs."

Jan 1, 2016

By N. Romani, R. Provost

"Commissioning of a circulating dry scrubber plant was recently completed at an existing facility, in order to treat the sulphur dioxide off-gas emitted from rotary kilns. Proper planning of the different commissioning stages and staffing an integrated team are the most important factors required for a successful plant start-up. A strong operational readiness plan must be in place as early as the start of construction in order to ensure a smooth transition from commissioning to operations. Plant performance can meet or exceed performance criteria within the required timeframe if the proper group dynamic and good communication is established between construction, commissioning and operations teams.INTRODUCTIONCommissioning of a circulating dry scrubber (CDS) plant was recently completed at an existing facility in Quebec, Canada. The CDS plant treats the sulphur dioxide off-gas emitted from rotary kilns in order to meet increasingly stringent environmental requirements. This installation enables the existing facility to reduce their sulphur emissions by over 90%.The CDS ProcessA general overview of the CDS process is presented in Figure 1 below. The combined, de-dusted off-gas from multiple kilns is sent to the CDS, which acts as an entrained fluid bed, where the gas is contacted with a water mist, re-circulated solids and hydrated lime. The SO2 from the gas stream and the available calcium hydroxide (Ca(OH)2) from the hydrated lime dissolve in the water and react to ultimately form calcium sulphites and gypsum. The solid residue (referred to as CDS residue), is the primary byproductof the process.Fresh hydrated lime and CDS residue is captured by the dust collection system and is re-circulated to the CDS via a fluidised transport system. Clean off-gas passes through the dust-collection system and is then sent to the atmosphere by a single exhaust fan.The CDS residue purged from the system is combined with the dust collected from the kiln offgas system and this mixture is wetted in the already exiting agglomeration system, to minimize dust generation during handling, and then sent to disposal."

Jan 1, 2016

By K. van Netten, T. P. Ernst

"Froth flotation has been used successfully for about a century in the beneficiation of both coal and mineral particles. With the on-going trend towards lower feed grades, however, there is a need to transform this technology in ways that can deliver ultrafast separations, with strong selectivity, and recovery, covering a broader size range. It should be recognised that the hydrophobic effect, with its highly selective and long-range interactions, will most likely underpin any new technology. We identified the separation of the concentrate from the tailings as the rate determining step of conventional flotation technology. This limitation was then addressed by developing a novel flotation technology, insuring the formation of a concentrate that could be separated more rapidly from the tailings. We introduced a novel binder medium, a highly concentrated water in oil emulsion, to act as the focal point for hydrophobic adhesion, effectively replacing the air bubbles used in conventional flotation. The hydrophobic particles adhere to and become embedded within the binder, forming saturated agglomerates that float upwards. Moreover, by forming these large and resilient agglomerates, the product can be quickly dewatered over a screen and separated almost immediately from the tailings. Remarkably, this new binder permits residence times in the order of a few seconds under batch conditions. This paper examines the performance of the technology as a function of the oil wt% added to the slurry. The paper also examines the performance of the technology as a function of the particle size, showing a decline as the particle size exceeds 0.50 mm.INTRODUCTIONFroth flotation involves the collision and adhesion of hydrophobic particles to rising air bubbles, the carrying of those particles from the bubbly-pulp zone into a froth zone, and subsequent drainage and migration of the pulp to achieve the final concentrate (Wills, 2006). Within a Jameson Cell the feed slurry and air bubbles are brought into intense contact within the active area of the downcomer, achieving rapid kinetics of hydrophobic particle adhesion to the air bubbles (Harbort et al., 1994). However, once the bubble laden product and tailings emerge from the downcomer there is the need for separation of the concentrate from the tailings, an inherently slower process. In other devices such as mechanical cells the initial kinetics of particle adhesion are far slower, relying on the turbulent eddies throughout the cell, while in a column the kinetics rely upon an even slower process of bubble interception with suspended and settling particles (Gorain, 2007). However, in all cases the driving force for segregating the bubbles from the tailings, and the drainage of the froth are inherently the same. We do note, however, recent advances by Galvin and co-workers in achieving so-called Fast Flotation, utilizing a system of inclined channels to dramatically increase the segregation rate of bubbles from the tailings, permitting much higher gas and feed fluxes to be applied, achieving up to a ten-fold throughput advantage (Dickinson et al., 2014). Any further improvement within the existing flotation paradigm would require the introduction of centrifugal forces, but this would also require the formation of much finer bubbles than is typically used given the tendency of relatively large bubbles to reach a limiting slip velocity due to deformations and increased drag. Across all flotation devices we argue the rate determining step remains the segregation of the bubbles from the tailings."

Jan 1, 2016

By Elliott Giles

"Measuring a blast’s performance based on the bucket fill time or “diggability” has always been achallenge due to the subjectivity generally involved. The diggability of a blast is often based onopinions and speculation without the data to properly support the claim. This paper focuses howthe blast design can impact diggability and how it can be properly measured."

Jan 1, 2016

By R. J. Hundermark, L. R. Nelson

"The critical importance of tap-hole design and management for furnace performance and longevity is explored through examining some of the specific matte, metal, and slag tapping requirements of non-ferrous copper blister and matte converting and smelting, ferroalloy smelting, and ironmaking systems. Process conditions and productivity requirements and their influence on tapping are reviewed for these different pyrometallurgical systems. Some critical aspects of the evolution of tap-hole design to meet the diverging process and tapping duties are examined. Differences and similarities in tapping practices and tap-hole management are reviewed. Finally, core aspects of tap-hole equipment and maintenance are identified – aspects that are considered important for securing improved tap-hole performance and life, so pivotal to superior furnace smelting performance. IntroductionThe sheer diversity of tapping configurations used on industrial pyrometallurgical operations is at first bewildering. They range from historical tilting furnaces without tapholes to modern eccentric bottom tapping (EBT) tilting and/or bottom slide-gate electric arc furnaces; to classical single tap-hole multiphase tapping (e.g. metal/matte and slag); to dedicated phase tap-holes (e.g. dedicated metal/matte-only and slag-only); to dedicated phase multiple tap-hole configurations (up to eight metal/matte-only tap-holes and six slag-only tap-holes); to more esoteric metal/matte-only siphons and slag overflow skimming, e.g. Mitsubishi Continuous Process (Matsutani, n.d.). This can be further complicated by periodic batch tapping; consecutive tapping on a given taphole; alternating tap-hole tapping practice; near-continuous slag-only tapping, with discrete batch matte/metal tapping on higher productivity, but low metal/matte fall (<20% by mass feed) Co and Ni ferroalloy and platinum group metal (PGM) matte furnaces; near-continuous tapping through batch tapping of individual tap-holes that are opened consecutively (Tanzil et al., 2001; Post et al., 2003); to fully continuous tapping on coupled multi-furnace cascades (Matsutani, n.d.)."

Jan 1, 2016

By Dean Treweek, Anthony Harding

"Creating stable, safe, constructible and cost effective support to openings in segmental linings is often an important component of successful delivery of a tunnel project. The many constraints on successful implementation include operational, spatial, geotechnical, structural, and constructability. Failure to address these adequately can lead to significant impacts on cost, schedule, and safety. With reference to past project experiences, this paper provides a guide to the most commonly deployed solutions and their pros and cons to help designers quickly identify the most appropriate solutions for a particular project, or act as a starting point for developing new and/or project specific solutions. It highlights the challenges that designers and contractors must address together for successful support of tunnel openings, and the constraints that arise. It then describes the common structural forms of support, and how each form can mitigate the constraints, allowing an effective opening support system to be implemented. INTRODUCTION While only a small portion of the total excavated volume of a typical tunnel, cross passages are often one of the most complex elements of a bored tunnel to construct. Cross passages in soft ground typically involve ground improvement, groundwater control, and multiple temporary support measures to ensure safe construction in ground that has been overstressed due to the construction of the running tunnels. Permanent lining construction requires careful detailing of waterproofing and reinforcement to support both long term ground and water loads and support the broken out rings of the main lining. While there is not a great deal of literature specific to cross passage construction, the main issues are discussed in some detail by Lawrence and Taylor (2011). However, the temporary support of the running tunnel segmental linings during cross passage construction is not always given the attention it deserves. The authors have been unable to find much literature on the design of such systems, much less the considerations that have led to a particular solution. Lawrence and Taylor only mention two potential methods of support. It may be easy to dismiss the opening support as an inconsequential item, but selection of the wrong support type can have significant impacts on both cost and schedule."

Jan 1, 2016

By Shen Zhengchang, Dong Ganguo, Chen Dong, Zhang Ming

"It is advantageous to process low grade ores with large scale flotation cells. Large-scale flotation cells have been enhanced with effective volume scale-up. In this paper, the latest and largest flotation cell with effective volume of 680 m3 in China is investigated. The hydrodynamics and flotation kinetics characteristics are conducted using CFD simulation. The similar circulating flow is formed compared to the previous BGRIMM (Beijing General Research Institute of Mining and Metallurgy) flotation cell and it is a suitable fluid dynamics environment. It is demonstrated that the flotation cell produces good gas dispersion and solid suspension. It is indicated that kinetic eddy dissipation plays a key role on collision kernel and collision probability profile. The higher collision probability profile appears at the impeller and stator regions aiding good metallurgical performances. The properties of the large-scale flotation cell are assessed using hydrodynamic numbers. The variation of hydrodynamic numbers such as the power number Np, the Froude number Fr, the air flow number Na, etc with flotation cell volumes show similar properties to previous flotation cells proven to be good in engineering applications. This research would aid structure optimization of the 680 m3 flotation cell.INTRODUCTIONFroth flotation is one of the mains method used in the mineral industry, which is used to process the most of metallic minerals. The proportion of low grade ores has increased with the minerals exploited around world. The increased capacity of concentrators demands large-scale flotation cells. Therefore, flotation equipment has seen a significant increase in size, for which large-scale flotation cells have prominent advantages in improving metallurgical performances, reducing area of plant blueprint printer, lowering the power consumption of the unit ore, decreasing labor cost and overall capital cost. Since the end of 1940’s, flotation cell sizes have continuously increased. To the end of 1990’s, flotation cells with the effective volume of 200 m3 were developed. In the last two decades, flotation cells have achieved a dramatic increase in size. In 2003, an industrial experiment on 257 m3 Smart Cell flotation cells was carried out in Minera Los-Pelambres, Chile. In 2007, the first 300 m3 Tank Cell flotation cell was designed and obtained industrial application in Macraes gold ore, New Zealand. And 320 m3 BGRIMM flotation cells are also in good operation in Toromocho Copper Mine, Peru and Wunugetushan Copper Mine, China. However, flotation cells are conventionally designed using empirically derived relations and geometric similarity. The continual scale-up of flotation cells is still a significant developing process. A 500 m3 Tank Cell was designed for the industrial experiment in Finland and a 620 m3 Tank Cell have also been completed the design. A 660 m3 Super Cell also was manufactured for the industrial experiment released in IMPC 2014. So, the flotation cells with volume exceeding 600 m3 become a pioneering research field for researchers worldwide."

Jan 1, 2016

By J. L. Carr, A. K. Smith, C. C. Jobes, G. T. Homce

"Underground continuous mining machines pose a difficult safety challenge since their operators generally work in close proximity to these machines in very restricted spaces. Intelligent software for use with magnetic proximity detection systems has been shown to accurately locate workers around mining machinery in real time. Calibrating these systems requires the manipulation of a lot of data to determine the calibration constants. Researchers have developed software to analyze, convert, and visualize data acquired during this calibration process to more accurately model magnetic fields and their interaction with the environment. This paper details the background, development, and operation of the resulting application software focusing on the utility of the graphical user interface to visualize the magnetic field calibration data. The refined data developed by this process can then be utilized by the proximity detection system to more accurately identify the location of miners working in an underground mining environment. INTRODUCTION Roughly half of the electricity consumed in the United States is produced with coal, and roughly one-third of all US coal production comes from underground mines [1]. Over the last century underground mining health and safety has seen a continuous and dramatic improvement. However, machine-related injuries and fatalities continue to be a major safety concern [2]. Every year, hundreds of miners are severely injured while operating underground mining equipment, and 39 miners have been killed in striking/pinning accidents involving continuous mining machines (CMMs) since 1984. CMMs, such as the one shown in Figure 1, are large mobile machines that are used to mechanically cut coal in an underground mine. These machines weigh approximately 40 to 50 tons, have hydraulically articulated appendages, and are capable of moving at speeds up to six feet per second [3]. Modern CMMs are remote-controlled, yet the operator and other miners are often in close proximity to the machine. Recent research by the National Institute for Occupational Safety and Health (NIOSH) reveals that the locations workers take relative to the CMM are usually influenced by visibility requirements and safety concerns [4]. The Mine Safety and Health Administration (MSHA) estimates that at least 28 fatalities involving CMMs since October of 1984 may have been prevented with proximity detection technology [5]. MSHA further estimates that proximity detection could prevent 20% of all deaths throughout the industry [6]."

Jan 1, 2016

By Behzad Vaziri Hassas, Firat Karakas, Esra Tanisali, Mehmet S. Çelik, Ahmad Hassanzadeh

Coagulation is basically an aggregation process where particles settle under the influence of interfacial forces with electrostatic forces playing a governing role. Although particle morphology consisting of shape and roughness dictates the physical encounter of two particles, their eventual coagulation is not only influenced by columbic forces but also other interfacial forces such as hydrophobic interaction, which affects the extent of aggregation of particles through increasing the distance of interaction. Roughness is well known to increase the effective contact angle on hydrophobic surfaces and also enhance interfacial forces. In this study, the effect of morphology of particles and particularly roughness on the settling velocity and in turn coagulation tendency was investigated. Batch settling tests (BSTs) of different particle morphologies were investigated as a function of pH. Two different morphologies of silica particles were utilized with the same particle size distribution (PSD) including smooth-spherical and rough-spherical (Etched). Rough particles were prepared by acid etching technique using hydrofluoric (HF) at different time intervals (15-300 sec). Etched samples were identified and quantified by optic profilometry. Settling test results showed that the settling velocity of particles in a suspension of 2% solids in the massive settling region is significantly affected by particle morphology of the suspension. Coagulation results further revealed that aggregation of rough particles is faster than smooth-spherical particles. Coagulation results are elucidated on the basis of particle morphology and its effect on distance of separation through hydrophobic forces.

Jan 1, 2016