Search Documents

By Cesar Santos, Marcelo Duarte Silva, Ediron Antônio Lage, Fábio Silva dos Santos

Ceramic filtration technology, despite consuming about 90% less energy than conventional vacuum filters and producing clean water ready for reuse, faced a big challenge that put in doubt its technical and economic viability. In 2015, the production of pellet feed in this last stage of the process of the Minas-Rio Complex of Anglo American was impacted by deep fillings in the filter medium. The chemical regeneration process indicated by the filter manufacturers did not have the necessary effect. SUEZ then carried out a research work on the potential causes and indicated specialty chemicals. After an intense work of the Anglo American technical team supported by SUEZ, an efficient regeneration methodology was developed. From this reference, SUEZ received another 03 similar challenges with ceramic filters. Among them, the Herculano Mineração Dry Stacking pioneer project, which until 2017 could not process more than 20% of the tailings generated in the pellet feed concentration process. Following adaptations in the regenerative methodology as a function of the mineral characteristics facilitated by the development of a pilot backwash system, success was achieved, providing a condition for production of 3.0Mtpy without the use of tailings dam and with continued decline in the unit cost of the tailings filtration operation.

Oct 3, 2019

By Raquel Húngaro Costa, Jonathan Tenório Vinhal

The demand for natural resources has grown over the years, however, the environment offers a limited amount of these resources for exploration. Then, the investigation of new methods for recovering and reuse some compounds and elements are essential to know later tailings purposes. Zinc is used in corrosion resistance as a protective coating for several products. One of the steps for the extraction of zinc is by flotation process to obtain the concentrated ore, in which a residue is generated. The aim is to characterize this residue, allowing the choice of recovery routes for compounds and elements in future stages. The methods of analysis were Malvern, VA, Eltra and ICP-OES, besides the water content. In this study, a characterization of elemental chemical analysis was performed, in which the main elements presented were: calcium (17.4%), magnesium (10.3%) and iron (7.97%); the water content was 27% and the grain size of the material presented an average size of 50μm. With the presented characteristics the material can be used, after treatment, in the recovery of other compounds for applications in the sector of fertilizers, ceramics and steel industry.

Oct 3, 2019

By Caio Trindade Almeida, Tharcysio Oliveira Rocha Paiva

Tharcysio de Oliveira Rocha de Paiva2

Oct 3, 2019

By Flanelson Maciel Monteiro, Marcondes Mendes de Souza, Mauro Froes Meyer

This research is based on a bibliographical review of a field work that was done in the municipality of Parelhas / RN. The area explored, in turn, is known for its richness of mineral resources that are present in pegmatitic rocks. The general objective of this research is to characterize the main properties of the pegmatites and quartzite, in order to verify the heterogeneity of the elements, to raise a possible viability of extraction for economic purposes. The quartzite also presents a siliceous chemical composition. This rock is a source of bricks and silica refractories used in the steel industry and for the preparation of the blast furnace bed, ornamental rock used in different ways (rustic, carved, polished, among others). However, this research resulted in preliminary data, but it would be interesting to be more detailed in order to evaluate the economic viability of these rocks.

Oct 3, 2019

By Delciane Porfiro, Tiago de Mattos Serodre, Antônio Eduardo Clark Peres, Valdirene Gonzaga de Resende

The evaluation of the effect of the addition of carbon nanotubes (NTCs) directly to a etheramine on the flotation recovery of the quartz at pH 10.5 was carried out by means of microflotation tests in Hallimond tube. The quartz flotation was evaluated using 0.1% (w/v) etheramine solution with different percentages of carboxylic functionalized NTCs. The increase in the percentage of functionalized NTCs increased the flotation recovery to a maximum and from this it was observed a reduction of the recovery of the mineral. Pure etheramine and etheramine with the NTCs were characterized by FTIR spectroscopy and thermal analysis. FTIR spectra of both pure etheramine and etheramine with NTCs clearly showed peaks with the same wavelengths and diagnostics of the cation etheramine and acetate anion. Thermogravimetry indicated that the etheramine + NTCs-COOH mixture lost approximately the same weight percentage over a larger temperature range. In addition, the interaction of the nanotubes with the etheramine caused them to decompose at a lower temperature.

Oct 3, 2019

By Rodrigo Fina Ferreira, Jacek Kolacz, Luciana Gois, Neymayer Pereira Lima

The recent developments on the sensor detectors together with the higher capacity of the machines, due the high-speed computing recent advances, have made possible extending the application in the mining industry. The use of x-ray fluorescence, x-ray transmission and radiometric sensor based sorting can selectively remove gangue minerals in different size fractions for different minerals. This paper summarizes the potential application of SBS for an iron ore in three size fractions aiming to increase the %Fe after the removal of particles with main gangue minerals associated. Pilot plant tests were carried out with samples of iron ore in different size fractions and different content of hematite and gangues. The use of x-ray transmission sensor showed the possibility to increase the %Fe from about 63% to above 68% for particles below 80mm and 45mm, after the removal of low density particles. The presence of fines on the feed affected the performance of the SBS X-rays transmission machine, especially for the fine fraction feed. The mineralogical determination, carried out to know the association between hematite and gangue minerals, and the density of the particles on the feed, can be used to preview the quality of products of the x-transmission sorting process.

Oct 3, 2019

By José Francisco Cabello Russo, Denilson Rodrigues de Araújo, Elias Fonseca de Castro, Henrique Dias Gatti Turrer

The Minas-Rio project of the Anglo American group was designed to produce pellet feed from a low-grade itabirite. The comminution circuit has three HPGR’s and two ball mills. This type of circuit, with HPGR (open circuit) followed by ball milling (closed circuit), is called a hybrid circuit. The literature shows this hybrid circuit as being more energy efficient. The main objective of this work was to evaluate the benefits of using the HPGR in the energy consumption of the grinding and regrinding and the secondary objective was to show the impact of the press on mass recovery of desliming and flotation, in view of a possible higher generation resulting from the pressing of the material. The results obtained in this work showed that the HPGR reduced the specific energy consumption in the comminution stages existing downstream of the press, increased the recovery of the flotation and did not decrease the recovery of the desliming stage.

Oct 3, 2019

By Walter Mazon, Marcello Rodrigues Cruz, Leandro Carvalhar Maciel

Filtration is the operation of liquid solid separation commonly applied in the mining industry. The use of filtering chemical agents is a technical solution viable for filtering optimization. The present work proposed to evaluate two filtering chemical agents (surfactants) to reduce the final moisture content of iron ore concentrate from Ferrous Resources. The leaf test top feed was done with the FLOTICOR FA 7241 and FLOTICOR FA 16557 products. The foaming profile of the filtrate was also evaluated, once excessive foaming is undesired when using this kind of products. The results showed a reduction in the final moisture of the filter cake. The product FLOTICOR FA 16557 achieved the best results, reducing final cake moisture from 10.4% to 9.8% at the dosagem of 25 g/t, besides presenting a fast kinetics in the foam drainage, presenting itself as a technical alternative for filtration optimization.

Oct 3, 2019

By César Junior dos Santos, Fábio da Silva dos Santos, Robson Rodrigues Martins

Tailings disposal has been a recurring theme of research in the major mining process development centers. This is due to the great interest of companies in reducing the social and financial impacts of their environmental liabilities. Another major driving force behind the search for new alternatives is the recent cases of environmental accidents in Brazil and abroad. According to the International Commission on Large Dam (ICOLD), two major accidents per year involving dams are reported worldwide. Hence, we realize that the analysis of the topic as well as the search for solutions becomes a challenge for both entrepreneurs and research institutions. In this work, a case study of the Herculano Mining will be carried out, working in the extraction and processing of iron ore. The main stages of the study are: technological characterization of tailings from the beneficiation process, analysis of filtration processes of this material for disposal in piles, bench tests and evaluation of the performance of the industrial facilities of the company in question. Herculano has an installed ceramic filtration equipment that faces operational difficulties in certain types of ore. At first, all the possibilities of adjusting this process will be analyzed so that it can filter the necessary mass of waste, acting in the rheology of the pulp (sedimentation, flocculation), regeneration of the ceramic plates and adjustments of the machine (filter), in order to obtain the best condition.

Oct 3, 2019

By Flanelson Maciel Monteiro, Yago Lutz Castro Pinto, Marcondes Mendes de Souza, Mauro Froes Meyer

This article is based on a bibliographical review of a field work that was done in the Salina São Camilo in the region of Mossoró - RN. The general objective of this research is to present the main exploratory and beneficiation aspects of salt production. Among the aspects of salt is the properties of salt, history and mining, besides the aspects of environment and work safety. However, this research resulted in preliminary data, but it would be interesting to be more thorough so that the extraction of salt in the academic world is disclosed

Oct 3, 2019

By Luiz Peixoto, Andrea Falcon

There are a few ways to impact the capacity of a reciprocating compressor, by altering suction and discharge pressure and recirculation. By reducing the pressure drop in the section before the compressor it is possible to provide a higher suction pressure and subsequently achieve a higher compressor flow rate. The increase in the suction pressure while maintaining the discharge pressure reduced the demanded compressor Head. When considering oxygen compressors it is necessary to cautiously evaluate the safety norms and parameters due to the risk of explosions and fires due to high oxygen velocity.

Oct 3, 2019

By Klaydison Silva, Maurício Curi Segato, Elves Matiolo, Neymayer Pereira Lima

Flotation is the main concentration process, has been applied with sucess for the removal of quartz on the iron ore industry aiming high quality concentrates. limiting the top size close to 0,300mm and the removal of slimes are fundamental for the efficiency of reverse flotation of quartz. The high consumption of reagents, leading to insufficient particle coverage, and increased foam stability, leading to the difficulty of removal of quartz particles, are the main deleterious effects of the presence of slimes. Recent characterization studies, together with the development of new collector of linear chain, allowed the obtaining of concentrate with SiO2 contents close to 3% with 94% of metallurgical recovery, based on pilot tests carried out on a sample flotation column of the Quadrilátero Ferrífero.

Oct 3, 2019

By Lucas Monteiro Corrêa e Lopes, Carolina Carvalho Nunes, Nathalia Luiza Nascimento de Carvalho

The characteristics of each ore make it impossible to predict the quality of a flotation concentrate without exploratory tests. The research begins with laboratory batch tests, and then, after advances in the determination of process conditions, the complexity of the tests increases in order to evaluate new parameters. The closed cycle test (LCT) simulate circuits with load recirculation and the greatest difficulty of this test is to stabilize the circuit and achieve equilibrium. Depending on mass availability, the types of tests that offer the highest reliability and informations about flotation in an ongoing process are mini-scale or pilot-scale tests. This work aimed to compare the results of the flotation tests in three scales (batch test, LCT and mini pilot) for the Bonsucesso ore, a new deposit, owned by Nexa Resources, that has sphalerite, zinc ore, and galena, lead ore. In the open flotation circuit of galena was obtained 27.57% content with 26.70% recovery, in the LCT test the content was 31.54% with 64.64% recovery and in the mini pilot reached 51.22 % content with 65.51% recovery. In the open sphalerite flotation the zinc content was 55.51% with 77.35% recovery, in the LCT test the zinc content was 56.71% with 84.42% of recovery and in the mini pilot of 50.02% content with 94.54% recovery.

Oct 3, 2019

By Jorge Alberto Soares Tenório, Susana Marracini Giampietri Lebrão, Guilherme Wolf Lebrão, Jefferson Salvador de Moraes, Viviane Tavares de Moraes

Os resíduos de mineração ou lamas são derivados dos processos de extração e beneficiamento mineral e por sua vez são geralmente armazenados em barragens de rejeitos, que são passivos ambientais. Algumas formas de recuperação de materiais desses resíduos já foram desenvolvidas, contudo a sua aplicação principal ocorre pela incorporação destes rejeitos em agregados da construção civil, visando a diminuição da geração de resíduos. Desta forma o objetivo deste trabalho é a caracterização do resíduo de lama vermelha visando a identificação de elementos que viabilizem os processos de reciclagem para a diminuição dos rejeitos. Para isso se fez uso de técnicas ambientais de classificação de resíduos, tais como: determinação da umidade; classificação granulométrica; determinação da alcalinidade; MEV/EDS e fluorescência de raios-X. As análises de caracterização convergiram para os resultados quantitativos elementar de 8,3 % de Al; 3,8 % de Na; 6,3 % de Si; 0,4 % de Fe; 0,4 % Zr; 0,004 % de Y, 2 % Ti e 0,009 % de Sc. Esta caracterização pode definir parâmetros que influenciam nos métodos para a recuperação de metais.

Oct 3, 2019

By Leonardo Araújo Peruch, José Fagundes, Henrique Carneiro Pinto, Marco Túlio Costa, Nayara Coutinho, José Fabiano Martins Assunção

The objective of this project was to increase the hot charge by reducing reheating energy consumption and raising the productivity of ArceloMittal Tubarão's hot strip mill by changing the HSM’s schedule process with optimization of the relocation process of slabs after HSM’s chance with focus on slab temperature in reheating time. The project began with the revision of metallurgical rules for the relocation of materials, definition of criteria temperature setting (hot / cold), definition of restrictions of the process and review of modus operandi scheduling process. With the implementation of the process / system it is expected to achieve a 10% increase in the hot charge index in slabs reheating furnaces and increase productivity of the ArcelorMittal Tubarão hot strip mill

Oct 3, 2019

By Leandro Augusto Viana Teixeira, Márcio Francisco Dill Junges, Adauto Caldara

Innovation in the mining industry is critical when facing ever growing challenges, like the need to increase safety, reduce social and environmental impact, deal with commodities price fluctuations among others. However, successful innovation is not only the product of technological innovation, but it is also dependent on Innovation Management, which consists of changing the way a company fosters innovation, creating a new structure able to leverage technology knowledge and the ability to convert this knowledge in value. This paper presents a restructure option for innovation that focus on R&D development linked to business needs and company strategy. This new system was approached based on four fundamental blocks for innovation management (Approach, Organization, Resources and Metrics), showing how the technology master plan and a management tool are able to bring together all aspects necessary for the proper operation of the system. The new system confirmed the importance of having the initiatives organized as innovation roadmaps, connecting techno-scientific development with the company needs through the use of KPIs that are relevant to the business.

Oct 3, 2019

By Fábio Heiji Yamada, Marcelo Koiti Fugihara, Ruano Fonseca Araujo

Conception the simulation and optimization technologies for industrial processes applied in the mining environment: tools and methodologies. Clarifications provided about the differences of these techniques when compared with static analysis (intuition, use of static spreadsheets, etc.). Presentation of practical cases at several big mining companies in Brazil. These projects will be presented and illustrated through dynamic simulation models developed at those companies, each one with its set of objectives, scope and results (for example: sizing the number of equipment, silo, piles related to the mining processing, logistics, ROM transportation, mine operations plan, etc.).

Oct 3, 2019

By José Hamilton Resende Tavares, Késsius Bortolan Menezes, Mariana Vieira de Moura

Sampling and its representativeness is of significant importance in process control and decision making in the mineral sector. In this way, the present work seeks to compare different methodologies for the sampling of the iron ore from Anglo American. Through a sample of 120 kg, representing the industrial flotation circuit feed, samples obtained by the method of long pile, random sampling and rotary sample divider were analyzed, being the latter adopted by the company. In this case, after sampling, the material obtained through each method was subjected to the same sequence of characterization tests and the difference between the results statistically analyzed. Through such analysis it was observed that the random sampling method showed high values of variability and is therefore considered as unsatisfactory when compared to the other methods tested. In addition, rotary sample divider also showed parameters slightly superior to the long pile method. This study confirms the importance of appropriate sampling systems and procedures systems in the pursuit of reliable results.

Oct 3, 2019

By Jackson Teixeira de Oliveira, Douglas Batista Mazzinghy, Vanderson Eney de Matos, Alexandre Camilo Leles de Figueiredo

This work studied the effect of different ball sizes in the secondary grinding stage of Samarco. The Moly-Cop Tools 3.01 spreadsheet was used for models calibration and simulations, considering grinding balls topsize of 15, 20, 25, 30 and 35mm diameters. A normal specific selection function up to the largest fed ore particle size (840μm) was obtained. The higher generation of fines and compliance with particle size specifications (+ 74μm and -44μm) proved to be more favorable for smaller ball sizes. The specific energy consumption was lower for the 15mm ball (10.7kWh/t), increasing up to the 35mm ball (13.0kWh/t). Although smaller diameter balls seem to be the best option for the size specifications, some factors may limit their use, such as: the higher generation of specific surface area; and the amount of ball purge in the discharge of the mills.

Oct 3, 2019

By Walter Valery, Kristy Duffy, Alex Jankovic, Peter Holtham

Hatch’s Mine to Process Optimization projects integrate mining and processing strategies, minimizing operating costs and maximizing overall profit. The methodology involves ore characterization, blast audits, plant surveys, analysis of historical data, and integrated modelling and simulation of mining and processing. Blast designs are tailored according to ore type and the downstream process is optimized for the changed feed. This approach has increased throughput and minimized costs for many operations worldwide. The implementation of this methodology at an iron ore operation that faced challenges with increasing mining strip ratio and ore body mineralogy changes is presented in this paper. The larger stripping ratio increased mining costs and constrained the run-of-mine (ROM) delivery to the process plant. Process performance was affected as the ore mineralogy shifted from predominantly hematite to include greater proportions of magnetite. The project objective was to minimize overall cost per ton mined and processed and maximize profit. Tailoring the blast designs according to ore type and process optimization increased the throughput of all process lines. This provided the potential to shut down one of the five processing line, aligning the mine and plant capacity and significantly reducing the processing costs.

Oct 3, 2019