Search Documents

By Louis H. Berkelhamer

"INTRODUCTION In the present war, with increasing demands on foundrymen for speedy production of sound castings, the role of sand in foundries has paramount importance.Foundry sands include both molding sands and core sands. Molding sands are those used in making molds, whereas core sands include those used for ""cores"" that fill the parts of the mold intended to be openings or hollow spaces in the casting. Core sands are, as a general rule, relatively coarse-grained as compared to molding sands. Coarse-grained sands, however, are required in making molds for large castings.Owing to the intimate relationship between properties of the sand and casting defects, it is necessary (for most efficient foundry work) to keep a close check on the molding sands used and to properly select and prepare a sand for a specific job. A mold is essentially an unfired refractory composed to meet specific requirements as to strength, permeability, and resiliency. Good green strength is important in preparing and handling the mold. Low dry and hot strengths contribute to cutting and washing, whereas high strengths cause difficult shake-out, with subsequent loss of sand. When molten metal is poured into the mold: a dried skin is attained, and gases from moisture and combustibles are driven off. Excessive moisture necessary for the proper working of a sand, as well as poor venting due to low permeability, are factors responsible for producing such defects as blows and pinholing. The skin of the mold, upon contact with molten metal, first expands and later contracts; these conditions are favorable for producing scab defects. Contact with the molten metal sometimes causes the skin of the mold to sinter or fuse and may produce a sand burn on the casting. Then again, the mold may develop excessive hot strength rapidly, thereby causing a cracked casting. Experienced foundrymen can other such relationships, too numerous to be included here."

Sep 1, 1944

Traditionally, the gravity cleaning of coal has been evaluated in pilot plant tests. Attention is now turning to the development of empirical models of gravity cleaning equipment that can be used for the design and evaluation of circuits. This paper presents some preliminary information for spirals and water-only cyclones treating fine coals. Also discussed is how such information gives a better understanding of the operating and performance characteristics of this equipment, how realistic comparisons can be made between different types of equipment, and how small mobile plants could be designed for treating the fine coals 'stockpiled' at many NZ mines.

Jan 1, 1985

By William Gleason

The numbers tell the story of this one. More than 50,000 people and 1,890 exhibitors took over the Las Vegas Convention Center Sept. 24-26 for the largest mining trade show in the world ? MINExpo. Inside the convention center, some of the largest machines used in mining were on display. Caterpillar, Liebherr, Komatsu and Hitachi displayed ultraclass offroad mining trucks and shovels. Atlas Copco and Schramm were among companies that rolled in mining drills and Bridgestone, Goodyear and Michelin were among the companies showing off the massive tires used by the trucks. Throughout the three halls and an outdoor display area, just about every kind of product, gadget or service used in the mining industry could be found on display somewhere.

Jan 1, 2012

By Michael S. Wieland

Toxic fumes cause fatal and nonfatal incidents in underground mining, where the working environment tends to trap the fumes, hindering the restoration of nonharmful conditions. Workers can underestimate the residual fume toxicity and return to the work site too quickly. The toxic fumes from charge explosions depend upon a number things: formulation ingredients, mixture uniformity, water resistance, hole contaminates, rock hardness, and dust interactions. Hole-to-hole shock waves and rift compressions can partially desensitize charges, ruin the reaction kinetics, and worsen the fume toxicity. Traditionally the fume hazards for candidate explosives are resolved for a restricted set or tally of theoretical or measured fume components, transformed to standard reference conditions. The relative fume toxicity RFT is the resultant influence reckoned from a formulated sum of concentrations within the tally that are unweighted or weighted with chosen multiplying constants. The RFT result is compared to a rule criterion that represents the worst case tolerable fume toxicity stipulated by regulations or otherwise. The ranking and comparison of different hazard potentials that would otherwise remain unwieldy is rendered tractable by the common format of the RFT notation.

Jan 1, 1998

Many mining operations are uncertain of what costs they should be achieving. The majority of cost estimates are based on historical costs that have added contingency factors. Historical costs are a valuable source of information but a more precise costing method is necessary. There are several alternative methods for predicting costs. A methodology which provides the best indication of the achievable costs is one using a standard inventory list and a bill of quantities. The model is termed a Basic Principles model and addresses basic design principles and engineering constraints.

Jan 1, 1990

By Stephen M. Smading

Unique onsite assembly of a 12.43 m Main Beam TBM and back-up system was completed on September 18, 2008 in the remote mountains of the Sichuan province of China. The equipment was assembled onsite, without previously having been assembled and tested in a factory, utilizing a method called Onsite First Time Assembly (OFTA). The Jinping-II hydroelectric project features four parallel headrace tunnels approximately 18 km long, two of which will be excavated by TBMs and two by drill and blast. A nearby fifth tunnel is being excavated by a 7.2 m TBM to draw down ground water in advance of excavating the headrace tunnels. This paper addresses the following topics: ¦Project description including geology and terrain; ¦The decision process leading to onsite first time assembly, the assembly process and logistics, and lessons learned; ¦Design features of the TBM and back-up system; and ¦Operational history from startup to the writing of the paper.

Column flotation has been successfully implemented on a production scale in the Athabasca oil sands. In this application, bitumen is recovered and mineral matter is simultaneously rejected from a middling stream originating from a primary separation vessel. Exploiting the natural hydrophobicity of bitumen, the middlings streams have traditionally been processed utilizing conventional, mechanical flotation cells. Although these cells offer adequate bitumen recovery and mineral rejection rates, operating costs are high due to the required maintenance of the wetted mechanical components. In comparison, column flotation provides superior metallurgical performance while offering a lower maintenance demand. Both metallurgical and mechanical characteristics of column flotation are discussed to demonstrate the benefits of this technology for the recovery of bitumen from oil sands.

Jan 1, 2012

By C. M. Smith

DELEGATES from 26 Local Sections and- Divisions of the Institute had three stimulating sessions during the Annual Meeting, a few topics still remaining to be discussed after the two Monday sessions.. The final session was held on Thursday morning. An abstract of the discussion will be transmitted to each delegate present. The topics included: Student relations. Section operation, membership, employment, MINING AND METALLURGY, a new nonmetallic minerals Division. licensing of engineers, and increased allotments of money to Local Sections. Some of the Sections felt that the present limit of $250 allotted to them - from the national treasury was insufficient to carry on their activities, and that this maximum should he increased. A resolution to this effect was passed for transmission to the Board of Directors.

Jan 1, 1935

By Ray Wood, Rene Sterk, Robin Falconer, Sean Aldrich, Simon Nielsen

"The Chatham Rock Phosphorite project is situated 450 km east of New Zealand at approximately 350 to 450 m water depth. The deposit occurs as a thin layer of phosphatebearing glauconitic sand at the surface of the sea floor and has a thicknesses typically ranging from 0 to 1 m. The sand layer consists of mainly silt and sand-sized sediments, with phosphatised chalk nodules up to 15 cm in diameter. Phosphate nodules were first discovered on the Chatham Rise in the 1950s by a New Zealand Government survey. During the 1960s to 1980s several private and government sponsored cruises explored the Chatham Rise and surrounding seafloor area. A total of 1174 samples were collected over a 600 km2 area with the majority of the samples collected using a pneumatic -or large Van Veen-style grab-sampler.Since acquiring the licence in 2010, Chatham Rock Phosphate Limited has conducted six cruises in two programs in the Project area. A total of 261 samples were collected using a Van Veen grab, box core and grab samples.Sample quality and QA/QC measures varied considerably between the cruises and within each cruise. A critical part of the assessment of the data collected in the Project area was to determine what quality thresholds to use to allow or disallow data to enter into the estimation process. As part of the data verification process, the relative and absolute quality of the data was assessed in as much detail as practically possible. The best samples were those that were collected using the pneumatic grab, sampled the full sand horizon, had a small location survey error and had no other apparent data ambiguities. This paper describes the challenges for mineral resource estimation for an unconventional style of mineralisation using unconventional sampling techniques."

Sep 1, 2014

By Don Sakata

Jan 1, 2005

By J. Ostwald, L. T. Matthews, C. E. Loo

Australia has large reserves of pisolitic limonite. Mining recently commenced on the Yandicoogina deposit to produce a high-grade sintering ore. The ore contains about 10 wt% combined water and simulated sintering temperature profiles indicate that progressive dehydration of ore particles occurs in the temperature range 300-700 degrees C. Studies by optical microscopy show that although the dehyrdrated ore particles contain numerous cracks, there is no change in the microstructure of the ore because topotactic transformation to haematite results in the formation of compact masses of very fine-grained haematite microcrysts. When the ore is held at around 1 200 degrees C for 1 min significant recrystallisation of these microcrysts occurs, resulting in the formation of optically visible, micrometre sized haematite crystallites. Studies to simulate the behaviour of ore particles during sintering (as nuclear particles surrounded by a standard adhering fines mixture) show that the recrystallisation process occurs much earlier at temperatures of about 900 degrees C. Further studies indicate that CaO in the adhering fines mixture enhances the recrystallisation of the ore nuclei. The results of the investigation indicate that the pseudo-relict haematite in sinters produced from ore blends that contain significant levels of pisolitic limonite consists of dehydrated goethite that has undergone significant recrystallisation and grain growth, a phenomenon that is facilitated by the presence of lime derived from the sintering melt.

Jan 12, 1992

By Raja V. Ramani

Discussion in this section of the Handbook is limited to the working environment of miners, the mine workers themselves, and the machines used in mining (Fig. 11.0.1). The contents emphasize personnel health and safety aspects and engineering design and control practices to ensure a productive health and safety environment. Reference is to the health and safety of the individual miners as well as to the safety of the working environment. This Handbook also contains references to health and safety regulations in Chapter 3.2 and environmental protection in Chapters 3.4 and 7.3.

Jan 1, 2008

By Christopher Mark

A new method for the design of longwall pillars, called "Analysis of Longwall Pillar Stability" (ALPS), is described. The method is the final result of a research program that included two major field studies, extensive reanalysis of data from other in situ measurements, and detailed evaluations of available pillar design methods. The key problem addressed by ALPS is estimation of the abutment loads applied to longwall pillars. Based on underground stress measurements made in mines in three states, equations for predicting the magnitude, distribution, and time-of-arrival of abutment loads are proposed. Stress measurements are also used to evaluate empirical pillar strength formulas for use in longwall pillar design. ALPS has been verified by application to case histories from several mining areas, and examples taken from the Pittsburgh and the Blue Creek seams are presented. Step-by-step guidelines for using this design method are also given.

Jan 1, 1987

By Narong Thasnanipan

This paper presents the outcome of the contest on the prediction of the static axial load capacity of diameter 1.20m bored pile founded at 46m below existing ground. The test pile was constructed by wet-processed method and instrumented with vibrating wire strain gauges. Different methods used by the contestants in prediction of load-settlement characteristics are described and compared with actual load test results. Load-displacement behavior of test pile is found to be better than expected. Major difference between prediction and actual test is the higher frictional resistance of Second Sand Layer achieved in the actual load test. The hyperbolic load transfer method used by one of the contestants was applied to back-analyze the load-displacement characteristics of the test pile at different conditions.

Jan 1, 2006

Judicious placement of a range of geotechnical instruments was employed at the Tasmania gold mine, Beaconsfield, Tasmania, as a key strategy in the monitoring of rock mass conditions over the past four years. The range of instruments employed included vibrating wire stress-meters and hollow inclusion cells to monitor changing stress conditions, resistance wire and multipoint borehole extensometers to monitor the impact of stress changes on the integrity of the rock mass, and instrumented cable bolts and threadbar bolts to monitor the static and dynamic impact of rock mass changes on the installed ground control system. Initially the monitoring was of a qualitative nature, monitoring change from the time of installation. The value of the output was considerable when considered in relation to the ongoing seismic record which was also being monitored. It was clear from the seismic record and the monitoring results that stope blasting was the primary trigger for changing rock mass conditions. However, it was unclear how well observed behaviour was reflecting conditions anticipated by elastic numerical modelling. The latter had predicted significant stress increase in the near field of man-access footwall development. Qualitative monitoring and visual inspection did not support the modelling prediction, and this led to a program of quantitative measurement being undertaken. Measurement of the absolute stress condition in the backs of footwall development immediately adjacent to monitoring hollow inclusion cells provided the benchmark for tracking quantitative stress change. The program provided insight into the evolution of principal stress field magnitude and orientation in relation to rock mass change observed with extensometers and instrumented ground control elements, as well as providing a degree of calibration between the elastic numerical modelling and the virgin stress field. Calibrated monitoring data has also provided a useful benchmark for finite element modelling which is to be used for future mine-wide design.

Nov 25, 2010

By Tim O’Neil

“America’s mining industry brings good jobs to communities across America and provides the energy, minerals and equipment that are vital to our economic security and our way of life.” That was the surprise videotaped greeting from President George Bush at the official opening ceremony of MINExpo 2004in the Las Vegas, NV Convention Center. Jack Gerard reinforced the upbeat mood at MIN-Expo. He praised Nevada Gov. Kenny Guinn for his support of the mining industry, the state’s largest manufacturing sector. Gerard is the president and chief executive officer of the National Mining Association, the sponsor of MINExpo 2004.

Jan 1, 2004

By R. V. Ramani, C. J. Bise

INTRODUCTION Classification of coal seams as thin, medium, and thick is both subjective and relative and is more a reflection of the statistical mode of the thicknesses en- countered in a mining region. A geological factor more precisely understood as defined than thickness is the inclination of the seams to the horizontal, commonly referred to as the pitch or the dip of the seam. Thick and steeply pitching seams present far more challenges to the ingenuity of the mining men to devise methods for their extraction than the thick and less steeply inclined ones. In a marginal case, where a thick coal seam may be minable by surface or underground methods, the decision bears a close relationship to the technological developments in the mining scene. Near surface thick coal seams are a special gift of nature and are not as wide- spread as the ones that call for the application of under- ground methods. Recent advancements in surface mining equipment have made it possible to surface mine to great depths. Stripping ratios of 30: 1 (cu yd of over- burden removed per ton of coal) have been achieved. The extraction of thick seams which preclude the use of surface methods is the concern of this chapter. Specifically, the objective here is to outline the special technological factors in underground mining of thick coal seams and to illustrate through several case histories the methods that are practiced in the North American continent. For the purposes of this chapter, a thick seam is defined as one which is not readily minable with currently available equipment without modifications to the extraction method or the equipment. At the present time, a thickness of 4.8 m (16 ft) can be considered as the lower limit, although developments in equipment and methods can be expected to push this limit upwards. The data for the case histories were collected from two extended mine visits in 1975 and 1978, and from other published accounts of the mines visited. Reference is drawn particularly to reports by Bise, Ramani, and Stefanko (1976) and Rarnani and Kenzy (1979). THICK SEAM MINING METHODS The various methods of mining thick seams can generally be grouped into three major categories: full face methods, where the entire thickness of the seam is re- covered in a single pass; slicing methods, where the seam is extracted to its full thickness by horizontal or inclined slices either in an ascending or descending order; and caving methods, where the seam is undercut and the en- tire coal seam is recovered by caving the top coal into the excavated cut, or some variations of the basic sub- level caving method. As shown in Table 1, in each of these methods, the coal is removed by either room-and-pillar or longwall methods. Hydraulic mining and transport of the coal in open flumes or in pipelines are also practiced. Addition- ally, the void created by the removal of coal may be filled with a packing material (stowing) except in the caving methods. The pitch (dip) of the seam, particularly when it is greater than 0.26 rad (150), imposes severe operational limitations on mobile equipment. A more detailed general discussion of the methods can be found in Bise et al. (1976) and Vorobjev and Deshmukh (1964). Specific discussion on the many variations of the three basic methods can be found in the papers presented at the international symposia that were held in

Jan 1, 1982

By P. A. Croce

A total of 17 mine gallery fire tests (23 including sub-tests) were completed during this report period (10/1/76 - 11/30/77), directed at identifying a hazardous timber-set fuel-loading in a mine passageway that is otherwise free of combustibles. Results of these initial tests show that the capability of a particular fuel loading for propagating a fire is dependent upon the imposed ventilation air velocity and the ignition intensity, although this dependency needs to be better defined. It is also apparent that care must be taken when relating gallery test fire behavior to actual mine fire behavior, because of the restrictive length of the gallery. Present data indicate that some modification to the instrumentation scheme may be advantageous before proceeding with future tests.

Jan 1, 1978

By C. J. Beevers

Tlze influence of zirconium hydride precipitate mprphology on the fructure of Zr-H alloys tested at strain rates of 10- sec at 20° and - 196°C and at strain rates of -500 sec.-1 at 20°C has been inves-tigated. The critical stage in the embrittlement of these alloys was the fracture of the zirconium hyhide precipitates to form large interval cracks at a stress of 25,000 10 137,000 psi. In specimens con-temping up to 100 ppm H the preciptates existed as isolafed platelets in the zirconium matrix and their fracture as enhanced by low temperature (—196°C) and high strain rate (-500 set-f) loading. These resl~lts lead to the conclusion that the rate of strain hardening of the zirconium metal controls the frac-tzrm of the hydride platelets. Increased hydrogen contents of 500 to 2000 ppm resulted in an increase in the 1)volume fraction and size of precipitates and crlso led to crack propogation in the hydride at both 20 and —196C at the low strain rates (10'* sec-'). Quenching led to refinerment of hydride precipitate size and reduced the degree of embrittlement at — 196°C; this effect is attributed to the absence of fracture of the fine precipitates. The formation of zirconium hydride precipitates has been shown to be the cause of hydrogen embrittlement of zirconium.' Several investigators'-" have studied the problem in broad outline, demonstrating that impact-loading conditions, testing temperatures below room temperature, and increasing hydrogen content produce increased brittleness. For example, Muehlenkamp and schwope2 showed that the transition temperature for notched impact tests was raised from 150" to 350°C on increasing the hydrogen content from 45 to 490 ppm. The degree of embrittlement is also controlled by the morphology of the zirconium hydride precipitates. The solubility of hydrogen in zirconium decreases from 600 ppm at 550°C to 10 ppm at 20"C,~ so that the form of the zirconium hydride precipitates (ZrH2) can be modified by varying the cooling rate through the Zr-aZr + ZrH2 phase boundary.= Forscher showed that quenching a specimen containing 35 ppm H from above 315°C resulted in a reduction in area of 70 pct at -196"C, whereas slowly cooling from above 315°C resulted in a ductility of half this value. The role of the hydride precipitate in the fracture process has been examined by Young and schwartz6 and more recently by westlake.' From metallo-graphic observations on slowly cooled Zr-H alloys they have suggested that cracks are nucleated in the hydride precipitates by the interactions of twins in the zirconium metal with the hydride. The experiments reported in this paper show that crack propagation in the zirconium hydride precipitates is the critical stage in the embrittlement of Zr-H alloys. The factors influencing fracture of the hydride precipitates and crack propagation in the zirconium metal will be related to the problem of embrittlement. EXPERIMENTAL TECHNIQUES The zirconium used in these experiments was produced from an ingot of vacuum arc-melted iodide zirconium forged down to 1 in. diameter at 800' to 850°C. The 1-in.-diameter bar was surface-machined and cold-swaged to 0.375 in. diameter. After a vacuum anneal at 800°C for 1 hr the hardness was 60 to 70 Vdh. The total impurity content was approxi-

Jan 1, 1965

By Víctor Guimaraes

El presente texto señala las estrategias de planteamiento de minado en la minera Tintaya con el objetivo de maximizar el valor neto de la operación minera y a un nivel aceptable de riesgo. Este ciclo de planeamiento, evalúan diferentes alternativas dentro de los siguientes procesos como: optimización del pit (Uso de ley corte durante el proceso, diseño de taludes, Pit descontado, inclusión de nuevos procesos metalúrgicos y de recursos inferidos), generación de fases de minado (Parametrización de fases), programación de la producción (uso de optimizadores basados en programación lineal), planeamiento de desarrollo mina (incluye planes de drenaje subterráneo y superficial), Planeamiento corto plazo y actualización del plan de cierre.

Sep 9, 2007