Search Documents

By Tim Chapman

This general report considers what promoters of deep basement projects want from their teams and whether they get it often enough. Most large projects are based on complex financial models where the funding is related to a future income stream. Project delays and cost over-runs can critically affect the financial model. Too often, delays and cost over-runs originate in the substructure and foundations. We must take positive steps to improve our industry's reputation for reliability.

Jan 1, 2006

Data released by the Commerce Department's Bureau of Economic Analysis show continued gradual change in the real GNP's rate of growth in 1984, which has eased from an annual growth rate of 10.1 percent in the first quarter lo 7.1 percent in the second quarter, and then to 2.7 percent in the third quarter. The automobile industry strike in the last half of September had only a small effect, estimated at less than a 0.1 percentage point reduction in the growth rate. Among the components that comprise the GNP, personal consumption and fixed investment grew at lower real rates in the third quarter than in the second quarter, while net exports decreased. Personal consumption expenditures increased $0.4 billion in the third quarter, compared with an increase of $20.1 billion in the second quarter. Nonresidential fixed investment increased $3.9 billion in the third quarter, compared with $9.6 billion in the second quarter. The other component of fixed investment--residential investment--increased from $60.8 billion in the second quarter to $61.2 billion in the third quarter. Real net exports of goods and services decreased $1 1.3 billion in the third quarter, compared with a $3.1 billion decrease in the second quarter. Although exports increased from an annual rate of $144.7 billion to $150.2 billion, imports increased much more, from an annual rate of $1 56.2. billion to $172.8 billion (table 1).

Jan 1, 1984

By D. M. Aloi

In today's evolving and globalized world, mining companies are being pressured to move beyond compliance towards long-term sustainability and sustainable development. Companies are expected to "engage" with communities and measure the success of these engagements without a clear understanding of "how" to do this. This move, away from "Corporate" Social Responsibility (CSR) and compliance, develops more of a focus on "Community" Social Responsibility and sustainability. This shift in focus leads to the development of world-class projects that provide sustainable development for people, reduces the incidence of costly delays, and promotes good global citizenship for corporations. The process of "engaging" communities in mining project design and development leads to a stronger license to operate and sustainable development. To create this mutually beneficial relationship between communities and companies, communities must be "engaged" in the mining process as early as possible, preferably during the exploration or the concept phases. How to create this "engagement" remains elusive. How to measure the progress of this engagement is also problematic. The quantitative and qualitative metrics needed to measure both positive and negative impacts of the mining and community relationship will be discussed.

Jan 1, 2007

By R. V. Taborelli, P. B. Bucky

This investigation was carried on by means of models and the application of the principles of similitude to determine the effects of props, props and cribs and sand filling in longwall mining. The geologic structure and rate of face retreat were kept constant and the only change introduced was in the method of support. It is not felt necessary to repeat a description of apparatus, or to explain the fact that a scalar model made in all parts of the same material as the prototype will behave similarly to the prototype when rotated at speeds such that the centrifugal force is as many times the gravitational force as the prototype dimension is a similar linear model dimension. The reader is referred to earlier papers1,2 for further information regarding these statements. All models were made of sandstone and were as in Fig. 6. They are composed of a 3/16-in. ore body bed A, overlain by a 3/16-in. bed B, a ?-in. bed C and two ?-in. beds D and E. The model was rotated at + 2350 r.p.m. equivalent to a model ratio of 1268. It was worked back ¼ in. at a time before being replaced in the centrifuge and again rotated. Table 1 gives model and prototype dimensions occurring in this discussion, the prototype dimensions being 1268 times the model dimensions. Figs. 1, 2, 3 and 4 were taken while the model was rotating at 2350 r.p.m. One was taken for each face retreat of 26.4 ft., but for obvious reasons all are not presented. Fig. 1 (A-E) shows the behavior of this type of structure with face retreats of 26.4 ft. and no artificial support. Fig. 2(A-E) shows the behavior of this type of structure where breaker and face props were used. The props were exceptionally strong, being of steel ? in. square in cross section, and capped with 1/16 in. ± of soft wood and paper, to allow for roof deflection. The face props were

Jan 1, 1940

By P. B. Bucky, R. V. Taborelli

This investigation was carried on by means of models and the application of the principles of similitude to determine the effects of props, props and cribs and sand filling in longwall mining. The geologic structure and rate of face retreat were kept constant and the only change introduced was in the method of support. It is not felt necessary to repeat a description of apparatus, or to explain the fact that a scalar model made in all parts of the same material as the prototype will behave similarly to the prototype when rotated at speeds such that the centrifugal force is as many times the gravitational force as the prototype dimension is a similar linear model dimension. The reader is referred to earlier papers1,2 for further information regarding these statements. All models were made of sandstone and were as in Fig. 6. They are composed of a 3/16-in. ore body bed A, overlain by a 3/16-in. bed B, a ?-in. bed C and two ?-in. beds D and E. The model was rotated at + 2350 r.p.m. equivalent to a model ratio of 1268. It was worked back ¼ in. at a time before being replaced in the centrifuge and again rotated. Table 1 gives model and prototype dimensions occurring in this discussion, the prototype dimensions being 1268 times the model dimensions. Figs. 1, 2, 3 and 4 were taken while the model was rotating at 2350 r.p.m. One was taken for each face retreat of 26.4 ft., but for obvious reasons all are not presented. Fig. 1 (A-E) shows the behavior of this type of structure with face retreats of 26.4 ft. and no artificial support. Fig. 2(A-E) shows the behavior of this type of structure where breaker and face props were used. The props were exceptionally strong, being of steel ? in. square in cross section, and capped with 1/16 in. ± of soft wood and paper, to allow for roof deflection. The face props were

Jan 1, 1940

Edward Keller, Baltimore, Md. (communicatioin to the Secretary*):—It is pleasing to note the increasing amount of work on metallurgical problems that is being carried on by exact scientific methods, and the results of such labor issued by the laboratories of our universities. Without doubt, Mr. Bolles's paper will be welcomed by all progressive practitioners. Many of the results which Mr. Bolles presents to as are new; and I take exceptioil to a few minor points only. The first of his concluding remarks is as follows: "Mattes are not homogeneous, but are composed of distinct mineral entitier, and may be likened to igneous rocks, in which the mineral constituents fall out upon the lowering of the temperature and ensuing solidification." He quotes an introductory remark to a paper1 of mine, as follows: "The true chemical character of copper-mattes does not yet seem to have been definitely determined, i.e, it is still more or less of an open question whether they are true chemical compounds, or mixtures, such as igneous rocks." This quotation, taken alone, would convey the impression that Mr. Bolles's conclusion is entirely new. Had he quoted also another paragraph from my paper in question, it would be clear that he was, to a certain extent at least, anticipated. I take the liberty, therefore, to state the substance of my own work. In the paper referred to, I showed the existence of the phenomenon of liquation in mattes, and, continuing, said: " A more direct method to test whether a matte is a compound sulphide or a mixture of individual sulphides was attempted by applying hydraulic separation. A clean piece of matte was selected containing practically no magnetic oxide and of the following composition: Cu, 37.96; S, 24.45; Fe, 33.63; Zn, 1.25; Pb, 1.02 ; Sb, 0.26 ; As, 0.065 ; insoluble, 1.15 per cent. ; Ag, 26.7 ; Au, 0.04 oz. per ton. For such a test it is essential to select a chemically uniform piece, other-

Jan 1, 1905

By J. C. Uy, T. E. Davidson, A. P. Lee

The effects of hydrostatic pressures to 26 kbars on the micro structure of poly crystalline Cd, Zn, Bi, Sn, Zr, Mg, Cu, and Fe were examined. Pressure-induced microscopic plastic flow in the form of boundary migration, slip, multiple slip, or twinning has been observed either singly or in combination in cadmium, zinc, bismuth, and tin. No deformation was observed in zirconium, magnesium, copper, and iron. The occurrence of such deformation, in terms of its intensity and initiation pressure, relates directly to the degree of anisotropy in the linear compressibility. Pressure cycling does not significantly affect the residual tensile properties of a zinc alloy which exhibits pressure-induced deformation similar to that of Pure zinc. CLASSICAL elastic theory predicts that a superim-posed hydrostatic pressure will not induce shear stresses in an ideal material. Thus, in the case of homogeneous and isotropic materials plastic flow will not occur as a result of pressure exposure, regardless of the magnitude of the pressure, unless some form of phase transformation or permanent density change takes place. However, real materials, such as metals, often vary considerably from the condition of homogeneity and isotropy. For this reason, Vu and johannin' examined and observed hydrostatic pressure-induced microscopic deformation in polycrystalline cadmium and, zinc, but not in aluminum, to pressures of 9 kbars and indicated that its occurrence is related to anisotropy in the linear compressibility. In addition, Davidson and omaan' have reported pressure-induced deformation in polycrystalline bismuth below the 1-11 transformation pressure. It becomes apparent then that under certain conditions hydrostatic pressure can induce localized internal shear stresses in some metals of sufficient magnitude to cause plastic flow. In this work, eight pure single-phase metals of different lattice structures and degrees of elastic anisotropy were examined after pressure exposures of up to 26 kbars in order to establish the conditions under which such deformation occurs and the type of deformation as a function of pressure. The effects of pressure cycling on the mechanical proper-

Jan 1, 1965

By Robert B. Parsons

"Canada's mining industry has reason to celebrate the federal government's budget which was tabled on February 26, 1986. The budget contains an important proposal to improve the flowthrough share rules by effectively eliminating the investor's liability to third parties. This proposed rule change and other important budget proposals are the subject of this month's edition of Tax Notes. IntroductionWhile Finance Minister Michael Wilson's February 26, 1986 budget received a mixed reaction from business and labour leaders, the budget was mainly ""good news"" for the mining industry. A long-standing bugaboo in the flow-through share rules will be cleared up, a permanent set of rules will be installed for the tax treatment of Northern allowances, and limited partnerships will apparently be able to continue to serve a useful role in financing exploration programs. Flow-Through SharesThe present rules which apply to an investment in flow-through shares are structured in such a way that the relevant Canadian exploration expense (""CEE"") must be incurred by the investor, and not by the issuing corporation. Obviously, in the case of most flow-through share issues, this requirement that the investor incur the CEE poses a practical problem-the investor typically does not have the expertise or organization to incur the CEE. As a result, an integral part of most flowthrough arrangements is an agreement whereby the investor appoints another party (usually the issuing corporation) as his agent to spend the flow-through funds on CEE on his behalf. Although the issuing corporation might consequently be the party which actually spends the flow-through share funds on CEE, nevertheless the legal structure is such that the investor is the ""principal"" who is incurring the CEE. As such, the investor is legally responsible for any third-party claims with respect to the exploration program. Third-party liability might arise, for example, in the case of property damage, personal injury, environmental infractions, and so on."

Jan 1, 1986

By G. R. Phare

Explosives formulation is dictated by desired field performance, which in turn is dependent on such physical properties as strength, velocity of detonation, sensitivity, and water resistance. The design of explosives to obtain these properties is discussed with some reference to detonation and rock mechanics theory.

Jan 1, 1958

By A. C. Fieldner

THE Bureau of Mines has received many requests for Information concerning the methods its laboratories use for analyzing coal and coke and determining their heating value. The fuel investigations now conducted by the Bureau of Mines are an outgrowth of the work undertaken at the Government coal-testing plant erected in 1904 at the Louisiana Purchase Exposition in St. Louis, and the methods for proximate and ultimate analysis of coal used by the Bureau of Mines are based on those originally adopted by the chemists of the coal-testing plant and followed in the subsequent chemical work of the Government fuel-testing plants at St. Louis, Mo., Norfolk, Va., and Pittsburgh, Pa. The many valuable suggestions and criticisms received from N. W. Lord, director of the School of Mines, and from E. E. Somermeier, professor of metallurgy, of Ohio State University, at that time, are greatly appreciated; development of many of the methods for the proximate and ultimate analysis of coal now used by the Bureau of Mines is chiefly clue to these men.

Jan 1, 1951

By S. H. Ash

Unusual mining conditions prevail in the State of Washington because the majority of the coal seams lie on extra steep dips, and the roof and floor of the seams are of such a character as to require an excessive amount of timber- ing. The seams as a rule give off a considerable amount of methane, which makes good ventilation imperative. Due to physical conditions, supervision is costly and travel about the workings is difficult. Because of the facts stated, the accident rate has been above the average, and for some time considerable thought has been given the idea of making promotion of safety in and about the mines a responsibility to be shared equally by the employees and the management. With this idea in mind the legislature of the State of Washington, turing March, 1927, passed laws providing that safety committees be selected to function at the coal mines of the State and at the same time recognizing the fact that first-aid education is an integral part of any safety movement; legislation was passed making it mandatory to have all persons in and about the ines trained in first-aid administration. The provisions of the State mining law3 are as follows: "In every mine a general safety committee shall be selected, composed of the mine superintendent or manager of mines, one man selected by the employees or any association of employees in or around said mine, and a third member selected by these two. "The general safety committee shall elect one of the members to act as chairman and one to act as secretary. The duties of the chairman shall be to preside at all meetings of the general safety committee, enforce its rules and regulations and see that its business is conducted in a prompt and business-like manner. The secretary shall keep an accurate written record of the proceedings of all meetings, conduct its correspondence and post notices of regular and special meetings and other matters pertaining to safety. The duties of the general safety committee shall be to investigate all serious and fatal accidents; make bi-monthly.

Jun 1, 1930

By J. Richter, D. Schulze

J. Richter and D. Schulze (Deutschen Akademie der Wissenschafte zu Berlin)—Introduction. In a recent paper R. G. Garlick and H. B. Probst reported on experimental results of investigations of room-temperature slip in zone-melted tungsten single crystals.17 In the paper it was pointed out that slip lines could be detected with an optical microscope only after about 10 pet plastic strain of the crystal. In our investigations we could observe slip lines in tungsten single crystals of defined orientations already with an elongation of 0.02 to 0.03 pet.18"9 Experimental Technique and Results. The tungsten single crystals were produced from 4 to 5 mm sintered rods* as starting material by electron- beam zone melting. With single-zone-pass melting a speed of 0.5 mm per min was used, while three-pass melting could be handled at a speed of 3 mm per min. Crystal axis orientations were located in the shaded area of the stereographic triangle, see Fig. 6. Orientation 1 is located at about 18 deg and orientation 2 at about 5 deg on the great circle from [011] to [ill]. This corresponds approximately to the orientations P and M referred to by Garlick and Probst. Our single crystals had a length of about 70 mm and were profiled solely by electrolytic means, leaving grip ends at both ends of the crystals. Between the latter, a cylindrical crystal of 45 to 50 mm length and about 2.4 mm diam was obtained. The crystals were deformed at room temperature in a commercial tensile-testing machine to obtain a strain of 0.02 to 5 pet. The average strain rate e = eP/t for all tensile tests amounted to approximately 10 -6 to 10-5 per sec, with ep representing plastic strain and t the duration of applied stress. In Fig. 7 a crystal is shown elongated by 0.03 pet. The picture was obtained by means of an optical microscope. Figs. 8 and 9 give electron-microscopic pictures of slip lines of crystals elongated by 0.07 and 1.1 pet, respectively. For crystals with the orientation 1, see Fig. 6, only the two main slip systems (101)[111] and (110)[111] were found. With the crystals of group 2 the two main slip systems are again evident, with

Jan 1, 1965

By James R. Boyle

The value of Alabama's nonfuel mineral production in 1981 was $312.7 million, a decrease of $15.7 million from that of 1980. Output of most non fuel minerals declined; cement, crushed stone, lime, clays, and sand and gravel were the major commodities produced in the State. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in native asphalt, kaolin, and oyster shell; fourth in bentonite, dimension marble, and fire clay; fifth in masonry cement; and sixth in common clay, ferroalloys, and lime.

Jan 1, 1983

By H. De Cizancourt

The Pechelbronn (Alsace) field is the only important French producing field. During 1934, development was carried on as in previous years. The total output of this field reached 553,575 bbl. in 1934, showing a slight decrease from the 1933 figures. Of the total, 315,000 bbl. (56 per cent) was extracted by drilling, while 238,875 bbl. (46 per cent) was obtained by means of shafts and galleries. Exploration of deep Jurassic and Triassic horizons was still in progress at the end of 1934. A deep well reached the Upper Triassic at a depth of 34 m. (2736 ft.). (Information kindly supplied by M. S. Mena, Directeur Technique.) As mentioned before, the small Gabian field (Herault) is gradually being exhausted. No drilling operations were undertaken in 1934, the small production being restricted to the pumping of old wells. Two exploration wells, noted as "drilling" at the end of 1933, were completed in 1934; viz., Lavelanet (Ariége) at 3785 ft. and Santenay (Niévre) at 2578 feet. French Possessions Algeria.—No drilling at Tliouanet. Out of a total of 100 wells drilled in the area, only 8 are still producing. No exploration work is reported during 1934 in Algeria. Tunisia.—Two wells completed; one well drilling at the end of 1934. A total of 11 wells is reported to have been drilled before the beginning of 1935; out of these, 8 were completed before the present program was begun. Morocco.—Exploration work progressed actively last year. The outstanding event was the coming in of Ts. 26 well at 1243 ft. This well took fire, therefore great difficulties were encountered in the accurate measurement of initial production; the figure of 1500 bbl. of oil given here is a near estimate. Oil flowed accompanied by a great amount of water. The apparent decrease of drilling operations in 1934 is explained by the increase in field activities after the results of Ts. 26 were known;

Jan 1, 1935

By M. R. Shahan, C. E. Seaman, Mischler S. E., T. W. Beck

"Float dust deposits in coal mine return airways pose a risk in the event of a methane ignition. Controlling airborne dust prior to deposition in the return would make current rock dusting practices more effective and reduce the risk of coal-dust-fueled explosions. The goal of this U.S. National Institute for Occupational Safety and Health study is to determine the potential of open-air water sprays to reduce concentrations of airborne float coal dust, smaller than 75 µm in diameter, in longwall face airstreams. This study evaluated unconfined water sprays in a featureless tunnel ventilated at a typical longwall face velocity of 3.6 m/s (700 fpm). Experiments were conducted for two nozzle orientations and two water pressures for hollow cone, full cone, flat fan, air atomizing and hydraulic atomizing spray nozzles. Gravimetric samples show that airborne float dust removal efficiencies averaged 19.6 percent for all sprays under all conditions. The results indicate that the preferred spray nozzle should be operated at high fluid pressures to produce smaller droplets and move more air. These findings agree with past respirable dust control research, providing guidance on spray selection and spray array design in ongoing efforts to control airborne float dust over the entire longwall ventilated opening. IntroductionCoal mining processes produce airborne dust that naturally deposits on the floor, roof and ribs of mine airways. These fine dust particles, termed float coal dust when smaller than 75 µm in diameter, are deposited in the return entries of coal mines and can be reentrained by pressure waves induced by methane-air explosions (Rice et al., 1911; Nagy, 1981; U.S. National Institute for Occupational Safety and Health (NIOSH), 2006). These particles are also those most likely to participate in coal-dust-fueled explosions, which can potentiate and propagate explosions resulting in extensive damage. In order to meet compliance requirements of at least 80 percent incombustible content in the composition of material deposited in mine entries (U.S. Mine Safety and Health Administration (MSHA), 2016), coal mines apply an inerting agent, specifically, rock dust (Harris et al., 2009). Should methane be present in the mine atmosphere, the required fraction of incombustible content is further increased by 0.4 percent for each 0.1 percent methane. The removal of airborne float coal dust (AFCD) prior to deposition is an approach intended to make current rock dusting practices more effective by increasing the proportion of inert material to combustible material, resulting in a lower risk of coal-dust-fueled explosions."

Jan 1, 2018

By Tristan H. Jones

Beginning in 1987, miniature dataloggers approved by the Mine Safety and Health Administration (MSHA) were publicly available for sale. The principal among these was the model CR21XQM, manufactured by Campbell Scientific, Inc. These dataloggers had been tested and were deemed permissible by MSHA and thus could be installed in the return air of an underground coal mine. In 1996, production of all permissible Campbell Scientific dataloggers ceased due to lack of sales. Data collection with these dataloggers has been a staple of ground control research in the United States for decades, and, without them, or a replacement, the capability to monitor ground behavior is severely impacted. Since that time, any party requiring a permissible datalogger has needed to borrow one that was purchased during the production years. In order to fill this technology gap and ensure its own data-gathering capabilities, the National Institute for Occupational Safety and Health (NIOSH) has developed and refined its own miniature data acquisition system (MIDAS). On February 16, 2010, MSHA deemed the MIDAS to be permissible and approved it for use in the return air of an underground coal mine. The MIDAS is an intrinsically safe, 16- or 24-bit datalogger, compatible with a wide range of resistive, single-ended, and differential-type instrumentation. It contains enough data storage memory to operate for over a year with typical data rates and is efficient enough to do this on a single C-sized alkaline battery for that entire period. It is menu-driven and requires no programming knowledge to operate. It supports wireless or hardwired communication for datalogger setup and data download. This paper describes the design, field and laboratory testing, and capabilities of the MIDAS datalogger. While not as fully -functioned as the CR21XQM, it is the only new permissible datalogger available, and there is intent to make it available to the mining industry for purchase.

Jan 1, 2012

By Dale Preece, Ayman Tawadrous

This paper presents a number of examples of three-dimensional blast modeling in both surface and underground environments that include time-delay explosive decking. These examples include: 1) quarry blasting, 2) coal seam protection blasting, 3) mineral mine blasting with high energy time delayed decks, and, 4) underground single-level/single-shot drawbell blasting.

Jan 1, 2014

By R. J. Leary

The Bureau of Mines experimental blast furnace was blown with oxygen-enriched blast in combination with natural gas injected at the tuyeres. The air blast was augmented with oxygen to form an enriched blast containing 24,8 pct oxygen, and tests were run at natural gas injection rates of 4.5, 6.0, and 8.3 pct of the air blast. Similar enrichment to 26.8 pct oxygen was tested at natural gas rates of 7.2, 9.1, and 11,0 pct of the air blast. At intermediate proportions of natural gas to oxygen, (1) the fuel rate and the replacement ratio of coke by natural gas were unaffected by oxygen injections and (2) the productivity increased about 4 pct for each I pct oxygen added to the blast. The higher proportions of natural gas to oxygen were less efficient; in return for a lower coke rate, the fuel rate increased and productivity declined. A deficiency in reducing gas imposed a limit upon lower than normal proportions of natural gas to oxygen. Beyond this limit the formation of reducing gas was insufficient to support the rate of metal production. When this condition was encountered, the coke rate requirement for specification iron was abnormally high and production fell off badly. Adiabatic flame temperature is discussed as a means for proportioning oxygen and natural gas additions.

Jan 1, 1967

By H. T. Kennedy, S. M. Avasthi

An equation developed for gaseous hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 0.73 percent when applied to 264 natural gas and condensate systems including 2,043 PVT points. Another equation developed for liquid hydrocarbon mixtures predicts molal volumes with an average absolute deviation of 1.12 percent when applied to 346 crude oil systems including 1,759 PVT points. Both equations require composition of the mixture to be expressed as mole fraction of methane through heptanes-plus, hydrogen sulfide, nitrogen and carbon dioxide, together with the characteristics of the heptanes-plus fraction in addition to the temperature and pressure. The equations cover wide ranges of the variables involved, and their accuracy is considerably better than that of other available methods. The equations were differentiated to allow calculation of the coefficients of isothermal compressibility and isobaric thermal expansion. (In this paper the coefficient of isothermal com-pressibility and the coefficient of isobaric thermal expansion will be expressed as compressibility and thermal expansion coefficient, respectively.) Equations to calculate these quantities are presented. INTRODUCTION Calculations of reservoir performance for petroleum reservoirs require accurate knowledge of the volumetric behavior of hydrocarbon mixtures, both liquid and gaseous. Compressibilities are required in transient fluid flow problems, and thermal expansion coefficients are important in thermal methods of production. An accurate laboratory investigation of the PVT behavior of each reservoir fluid encountered would be costly and time consuming. For this reason various correlations for predicting fluid properties have been developed and recorded in recent literature. Correlations have been presented in the form of graphs, tables and equations. Since an increasing number of studies are being conducted with the aid of electronic computers, recent efforts have been directed toward development of correla-tions suitable for computer programming. Application of computers permits the use of more complex correlations which otherwise are not feasible. Moreover, methods for predicting reservoir performance, particularly those based on the compositional material balance, depend upon the capability of accurately expressing the molal volumes and other fluid properties as functions of pressure, temperature and composition. The coefficient of isothermal compressibility c is defined by

Jan 1, 1969

By Perry M. Jones

An important operational and environ-mental concern associated with in situ leaching activity is the balance between solution injection and recovery. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. The Bureau of Mines is investigating the factors that affect solution balance in an unsaturated ore deposit, as part of ongoing in situ leaching hydrologic investigations at the Cyprus Casa Grande Mine. Flow conditions in 58 injection and recovery wells at the Casa Grande In Situ Leaching Test Facility were monitored daily over an 18 month period. Changes in the balance between injection and recovery occurring during this period were evaluated using analytical and statistical methods. The results permit estimation of solution distribution and the volume of solution stored in microfractures and interstitial pore spaces within the deposit following 18 months of leaching. Approximately half of the difference between well injection and well recovery can be accounted for by solution movement through macrofractures into nearby drifts. Estimates of solution storage within the ore deposit at the end of 18 months of leaching range from 3.5 to 6.9 pet. of injected solution. These results also suggest that 13 to 26 pet. of the fracture/interstitial pore space in the deposit was saturated with solution after 18 months of leaching.

Jan 1, 1991