Search Documents

By T. C. Green

A two-phase program evaluated commercial proximity warning devices and then served to design and develop an automatic electrostatic field strength measurement device with improved performance. The Phase I program consisted of test and evaluation of three commercial proximity warning devices, all of which operate on the principle of electrostatic field intensity measurement for determining proximity to high voltage power lines. Performance testing of these devices utilized full-scale cranes and power line systems and a scale model facility. The evaluation results were reported in the Phase I report entitled "Evaluation of Proximity Warning Devices" dated 22 February 1980. Under the Phase II program, a microproressor-based data acquisition system was designed and developed to collect and measure field strength at distributed points around the crane boom. This unit (referred to as the Distributed Sensor AC Electrometer) measures the field strength about a crane boom using 17 distributed sensors. Keyboard control is provided for the equipment operator. Measured field strength values are displayed on a line printer and recorded on magnetic tape. Laboratory testing of this unit demonstrated performance characteristics and field strength measurement accuracy within the design goals. A Phase III measurements program is proposed using the AC Electrometer to map the field strength contours about power line configurations.

Jan 1, 1981

By J. H. Jones

The original term of grant No. 1115174 was September 1980 through December 1983. An extended progress report, covering this time period, was forwarded to the Bureau of Hines in January 1984. The principal investigators were given a no-cost extension of their grant to cover the period January through December 1984. The report which follows covers this latter time period only.

Jan 1, 1985

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By McHenry Mosier

This progress report on a national survey of the use of detachable bits in metal mines covers 10 mines. It presents comparative costs for drilling with conventional and detachable bits, describes the reconditioning of drill steel, and gives various data on rock drilling at these particular mines. Reports to follow will include similar data on drilling at other metal mines in the United States. ACKNOWLEDGMENTS This report is based on costs and data developed and furnished by the operators of the mines visited. The author is greatly indebted to the officials and staff members at these mines for their cooperation and assistance.

Jan 1, 1936

Hydrometallurgy has a history of over 300 years with copper leachingand cementation having been exploited in Spain as far back as 1670.Since then, hydrometallurgy has become an integral, expanding branch of extractive metallurgy. This paper reviews major developments in hydrometallurgy over thepast century with emphasis on recent commercial developments and their impact on the mining and metals industries. The environment in which these developments has taken place has changed significantly in the past two decades and many factors, often non-technical, have emerged as constraints on the operation of existing plants and the expansion and development of new hydrometallurgical operations. Finally, a number of possible new developments that will shape thefuture of hydrometallurgy in the new millennium are discussed,particularly as they relate to the assimilation of technical advances in other areas of science and engineering. The impact of current trends in the education of hydrometallurgists and the provision of research in support of these future developments is also addressed.

Jan 1, 2001

By Dave Bulled

"This paper describes the design of a molybdenite flotation circuit using FLEET technology applied to kinetics data produced from laboratory flotation testing and distributed across the blocks of a mine plan using a geostatistical approach. The geostatistics assigned the statistical error that arises from having a limited amount of sample testing data to the kinetics estimates of each block of ore in the mine plan. The final design then included a quantification of risk based on the accuracy of the block flotation kinetics and model fitting. The design made reference to the extensive technical reports describing earlier metallurgical test work including some pilot plant work over thirty years ago.The testing involved conducting MinnovEX Flotation Tests (MFT) to determine the rougher flotation kinetics at the specified reagent conditions and rougher-cleaner tests to determine the change in kinetics resulting from regrind. These flotation kinetics were used within FLEET simulations to create a full-scale flowsheet and plant design including recommended equipment sizes and the forecast of operating results. Measurement of detailed flotation kinetics for a wide range of samples allowed the effect of size of grind and efficiency of classification (i.e. width of size distribution) to be predicted for the whole ore body.INTRODUCTIONAdanac Moly Corp. proposed to develop a 20,000 ton per day mill to produce high quality molybdenite concentrate from its Ruby Creek resource in north-western British Columbia. It is a relatively clean low grade porphyry-monzonite occurrence containing minimal quantities of other sulphides such as chalcopyrite, pyrite, sphalerite and galena. Molybdenite occurs mainly as coarse flakes with lesser amounts of finer sized values. An optimum plant design was required to can achieve the predicted operating results, at a known level of risk, while treating the variability inherent in the ore body."

Jan 1, 2007

By James A. Finch

"I offer a personal view of what the next 30 years holds for mineral processing. Re-stating that mineral processing will remain a vibrant industry in raw material production, growth opportunities in waste management are identified. The processing sequence familiar now (mining -mineral processing -extraction) will become more interwoven. In situ processing (i.e., milling underground) will evolve from concept to demonstration. Opportunities to exploit physical properties altered in chemical (pyro-and hydro-) processing will present themselves. In primary grinding, the path to AG/SAG milling will progress with little deviation but opportunities in regrinding are wide open. Flotation will see the trend to designing bubble/particle reactors accelerate simultaneously with a vigorous response from mechanical cell suppliers. Gravity separation remains a bastion of the lone inventor but I anticipate that the new lines will come from the waste management business. I finish by examining the ""research cycle"", identifying growth in small ""high tech"" companies and university research centres.IntroductionI have been asked to offer a personal view of""where we are going in mineral processing?"". Gazing into crystal balls is quite a cottage industry as we approach the end of the millennium. Academics are often asked to assume the role of visionary, I presume because it is considered in their mandate, to reflect and philosophize (or, less charitably, because they are considered to have the time). Since this is the 30th Annual Canadian Mineral Processors Operators Conference, I am tempted to suggest the next 30 years as my frame of reference. This is about equivalent to one engineer's career or, given it takes typically 15 years to go from concept to realization in mineral process engineering (Napier-Munn, l 997a), about 2 ""invention cycles"". With this length of cycle, much that is familiar now will remain so over the 30 years.Research and development (R&D) is in response to need. The overarching need in mining is to find new ore bodies. Process developments cannot compensate for a depleting deposit or a declining commodity price. Mineral processing R&D is characterized by incremental gains, aimed at pushing the mine down the cost per tonne league table. Breakthroughs are the exception (flotation at the turn of the century was one). This must be kept in mind when trying to predict the future in our business."

Jan 1, 1998

By S. Frimpong

Hydraulic shovels are widely used for primary production in surface mining operations. Variability in material diggability, unstructured mining environments and limited space and operator inefficiency affect the performance of these shovel excavators. Dynamic models of the hydraulic shovels are essential for understanding and improving machine performance. This paper contributes to this subject area by advancing hydraulic shovel kinematics and dynamics using the modified Newton-Euler method. A virtual simulator is developed to simulate the hydraulic shovel performance in the ADAMS environment. The simulator is validated with data on shovel geometry and the physical and mechanical properties of a formation in a surface mining environment. The results indicate that a shorter digging time increases the shovel operating power requirements, and that the required peak power increases by 100% when the digging time reduces by 50%. Simulation results also show that a shallow trajectory facilitates the digging process, with 50% reduction in peak power requirements compared to a deep one. This simulator provides a powerful tool for performance monitoring, excavation process designs and structural optimization of hydraulic excavators. This work also forms the basis for developing comprehensive simulator models for automated shovel operations in constrained mining environments.

Jan 1, 2005

By R. J. Seibel

A statistical comparison of the dust exposures of coal miners with identical occupations in Pittsburgh, Pocahontas, Freeport, and Kittanning seams was conducted. Results indicated that, in some cases, identical occupations have different dust exposures in different seams. For example, the continuous miner operator in the Pittsburgh and Pocahontas seams is exposed to more dust than the same man in the Kittanning seam, but the Kittanning seam has more dust along the haulage roads than the other seams. Also, average dust exposures for similar occupations in continuous and conventional mining operations are similar.

Jan 1, 1974

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the peat producers in the United states and publishes economic data on the peat industry, based upon reports submitted by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all commercial producers, although a few small companies may not have been canvassed as the industry has many small operations that operate intermittently. Output of the various companies listed ranged from a few tons to more than 50,000 tons. Peat is included in the Bureau's annual surveys of the mineral industries because peat is classified as a mineral fuel. Although none is used for fuel in the United States, peat is a potential source of energy and ranks as one of our large mineral resources. The domestic peat industry sells peat, chiefly, for use as a soil amendment for general soil-improvement purposes. During the past decade the industry has expanded rapidly with operations increasing from 45 in 1947-494/ to 115 in 1960. Output during this period has more than tripled, increasing from 131,782 short tons to 470,889 short tons.

Jan 1, 1961

By Jan E. Nesset, Phillip J. Mackey, Joo Y. Kim, Giovanni Di Prisco, André R. Laplante

Understanding the appropriate gold recovery to associate with copper recovery when assessing laboratory testing on porphyry deposits is often complicated by several factors including variable and/or complex mineralogy, and the variability contributed by the low Au content of the various flotation products. As a result, gold recovery is often underestimated and the value contributed by the gold to project economics is less than it should be, a problem that could influence overall project viability. Typically, for these types of deposits, the gold recovery is found to be lower than the copper recovery. In this unique project, having the objective of seeking a better understanding of gold recovery relative to copper recovery, mill feed samples from a selection of six operating world-class Cu-Au low-grade deposits were collected along with the mill metallurgical results for the corresponding sample periods. The samples were subjected to laboratory flotation tests, as well as the Laplante gravity recoverable gold (GRG) test, mineralogical assessment and cyanidation leaching. The aim was to better understand the copper and gold recovery relationship, the links between laboratory and plant flotation performance, the influence of mineralogical differences, and the potential for enhancing gold recovery by gravity recovery techniques. A new correlation of copper and gold recoveries based on the results is presented in the paper. The results showed that the link between copper and gold recoveries established in the best laboratory tests were maintained in the plant results, and further, that the potential for improving Au recovery by gravity or flash flotation methods is directly proportional to the amount of gold greater than 75 microns.

Jan 1, 2005

By J. E. Bernick, J. Davies

This paper describes the design and construction of a 22.86 m (75 ft) long jacked tunnel, which was successfully installed, despite difficult mixed face conditions at Metro-North’s Westport Station, in Connecticut in the fall of 2003. The tunnel utilized what is believed to be, the first application of a steel grillage system within the United States. This grillage was installed before the jacking started and allowed the tunnel to be jacked under four live railway tracks, which included the Acela high speed line, without affecting train operations. The clearance between the top of the tunnel and the rails was only 0.9 m (3 ft).

Jan 1, 2005

By Harry Perry

One of the most notable achievements of the iron and steel industry in the United States in this century has been the general increase in productivity of individual blast furnaces and the reduction in coke rate. Most of the improvement in furnace operations has occurred within the past decade. During this time the output of the average furnace increased about one-third, while fuel rates decreased from 15 to 20 percent. For example, in 1949, the iron and steel industry produced 811.2 short tons of pig iron per blast-furnace day with a coke rate of 1,870.4 pounds per ton of pig iron, By 1960, the average production of pig iron per blast-furnace day had risen to 1,182.4 tons, while the coke rate had decreased to 1,497 pounds per ton of pig iron. These figures are averages for the entire industry; many furnaces produced over 2,000 tons per day and one furnace, operating on pellets, reached 2,700 tons of pig iron per day, Coke rates of individual furnaces varied, but some furnaces operated on less than 1,200 pounds per ton of pig iron. The significance of this decrease in coke rate is shown clearly when data on pig-iron production and coke consumption in 1959 are compared with 1948. In 1948, 57.3 million short tons of coke was charged into blast furnaces to produce 60.1 million tons of pig iron; in 1959 only 47.6 million tons of coke was needed to produce 60.2 million tons of pig iron. Thus, in 1959, nearly 10 million tons less coke was required to produce about the same amount of pig iron as was produced in 1948.

Jan 1, 1962

Advances in Thickener Feedwell Design via Computational Fluid Dynamics Modelling

Sep 13, 2010

By Greg Rasmussen

"Huckleberry Mines Ltd is an open pit porphyry copper-molybdenum mining operation located 120 km south of Houston, British Columbia with a 18,000 tpd milling facility. Huckleberry Mines is owned 60% by Princeton Mining Corporation, the operator, and 40% by Japanese partners.The Huckleberry deposit is one of several porphyry systems located in the Tahts a district of the intermontane belt of British Columbia. The principal economic minerals are chalcopyrite and molybdenite. The ore deposit is split into two ore deposits, the Main Zone, consisting of24,241,000 tonnes of mineable reserves grading 0.484 %Cu and 0.013 %Mo, and the East Zone, consisting of 66, 131,500 tonnes of mineable reserves grading 0.523 %Cu and 0.014 %Mo.The milling begins with gyratory crushing. This sizes the product down to 100% passing 6 inches. This product is discharged onto a stockpile by a stationary conveyor. The stockpile was designed for a capacity of 144,000 tonnes with a live capacity of 20,000 tonnes. Two apron feeders draw the ore from the bottom of the stockpile and discharge onto a SAG mill feed conveyor which in turn feeds a grinding circuit consisting of one 32' x 15' SAG mill and two 30' x 16.5' ball mills. The grinding cyclone overflow feeds bulk flotation at 55 -65% minus 200 mesh.The bulk flotation uses conventional rougher and column flotation methods to float a bulk concentrate recovering 92.6% copper on the East Zone and 95% copper on the Main Zone with 75% recovery molybdenum on both zones. The bulk concentrate feeds the bulk thickener which produces a density of 60 %solids. This in turn feeds the molybdenum circuit, which separates the copper and molybdenum, by depressing the copper then using conventional rougher and column flotation produces a copper concentrate of 27 %Cu and 0.02 %Mo, and a molybdenum concentrate containing 1.5 %Cu and 54 %Mo at 67% recovery. These concentrates are separately thickened, filtered, dried, and shipped to the smelter for processing."

Jan 1, 1998

Essential features of the role of the fill material in mechanized cut and fill mining are discussed, with particular emphasis on its dewatering and strength development after emplacement. The fill material is regarded as a chemically-reactive porous medium, the most important property of which is permeability. Methods are described for measurement of permeability and other fill properties and results of such measurements applied to develop an orderly approach to the operation.

Jan 1, 1966

By R. E. Old

Through the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-halance methods and the equations for natural water encroachment. to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed. Introduction With the decreasing rate of discovery of new oil reserves, attention is necessarily focused on the efficient development, evaluation, and production of existing reserves. From the nation's viewpoint, the necessity of conserving resources is obvious. From the operator's viewpoint, the problem is to lengthen the period of profitable operation, in an attempt to increase the return on his investment. To do this the operator must take advantage of the natural forces acting on and within the reservoir. Natural water encroachment, the nemesis of profitable operation in the past, can be and is being harnessed to produce a greater oil recovery during the stage of flowing production. Proper evaluation of water encroachment rates and a fuller under- standing of reservoir behavior dictate the appropriate production procedures. Complacency in hit and miss production is obsolete. Oil production must and will approach the efficiency of other businesses, such as manufacturing. A manufacturer will not place an article on the market until he has fully investigated the processes involved, additional investment in equipment, costs of production, and expected profits. These may be modified by actual experience at a later date, but at least he begins with an idea of expected return. It is just as logical that an oil operator should investigate these same factors during the development and the early period of production of an oil reserve. The complexity of the problems existing in oil reservoirs should not be underestimated. Conversely, they should not be regarded as insoluble. Many completely defy solution, but there are others that can be solved completely or attacked intelligently to yield approximate results. The petroleum engineer has many tools, both figuratively and literally, at his disposal. Physical data such as core analyses, electrical logs, bottom-hole sample analyses, and bottom-hole pressures are accumulated extensively. Advances in the analytics of fluid flow have kept pace with the advances in measurement of physical data. It is the purpose of this paper to show how some of these records may be analyzed to define certain phases of reservoir behavior.

Jan 1, 1943

By R. E. Old

Through the use of pressure and production records, formation properties and bottom-hole sample data, the performance of an oil reservoir may be studied analytically to define and evaluate the natural forces acting on and within the reservoir. Use is made of material-halance methods and the equations for natural water encroachment. to estimate reserves. Methods for calculation of pressures are given. A study of the Jones sand, Schuler field, Arkansas, has been made and is given here to illustrate the value of the methods discussed. Introduction With the decreasing rate of discovery of new oil reserves, attention is necessarily focused on the efficient development, evaluation, and production of existing reserves. From the nation's viewpoint, the necessity of conserving resources is obvious. From the operator's viewpoint, the problem is to lengthen the period of profitable operation, in an attempt to increase the return on his investment. To do this the operator must take advantage of the natural forces acting on and within the reservoir. Natural water encroachment, the nemesis of profitable operation in the past, can be and is being harnessed to produce a greater oil recovery during the stage of flowing production. Proper evaluation of water encroachment rates and a fuller under- standing of reservoir behavior dictate the appropriate production procedures. Complacency in hit and miss production is obsolete. Oil production must and will approach the efficiency of other businesses, such as manufacturing. A manufacturer will not place an article on the market until he has fully investigated the processes involved, additional investment in equipment, costs of production, and expected profits. These may be modified by actual experience at a later date, but at least he begins with an idea of expected return. It is just as logical that an oil operator should investigate these same factors during the development and the early period of production of an oil reserve. The complexity of the problems existing in oil reservoirs should not be underestimated. Conversely, they should not be regarded as insoluble. Many completely defy solution, but there are others that can be solved completely or attacked intelligently to yield approximate results. The petroleum engineer has many tools, both figuratively and literally, at his disposal. Physical data such as core analyses, electrical logs, bottom-hole sample analyses, and bottom-hole pressures are accumulated extensively. Advances in the analytics of fluid flow have kept pace with the advances in measurement of physical data. It is the purpose of this paper to show how some of these records may be analyzed to define certain phases of reservoir behavior.

Jan 1, 1943

Change is inevitable but learning from change is an option. Willingness to learn is one of the first lessons that a leader must learn. Get comfortable and get left behind. I propose to outline the main social changes which are taking place and their impact on the Minerals Industry. Also the changing way we do business and what are the skills needed to manage that change and diversity. How are Associations and Institutes responding to this ever changing environment? More specifically, what is my Vision for the Institute to assist professionals to achieve greater and continuing professional excellence in their chosen professions?

Jan 1, 2000

By Lenin Salazar Dulanto

La baja de precios en algunos minerales ha obiligado que las empresas mejoren su proceso productivo a través del uso de equipos de última tecnología en los procesos de mecánica, hidráulica, electricidad y electrónica, así como en la eficiencia en el corte y taladrado, extracción y transporte. Sin embargo, tanto el desatado y sostenimiento manual desarrollaron un estréss y desgaste de energía en el trabajador. En este sentido, el presente trabajo señala una nueva forma de realizar tales operaciones en el ciclo de minado de la empresa Milpo a fin de garantizar la seguridad física de los trabajadores y equipos.

Jul 31, 2003