Search Documents

By K. Rainer Massarsch, Bengt H. Fellenius

"Abstract Vibration limits for buildings with respect to ground vibrations from pile driving published in international standards are reviewed. At first, relevant vibration parameters are defined and the evaluation of vibration records is described. The sensitivity of structures to different vibration parameters (displacement, velocity and acceleration) is discussed. Most vibration standards relate to blasting activities, the dynamic characteristics of which can be significantly different to those from construction activities and in particular, pile driving. Several vibration standards are reviewed. The Swedish vibration standard is described in detail, as it is the only one accounting for several important factors, such as ground conditions, building material, and type of building foundation. Many standards limit the guidance to values based on the dominant vibration frequency and a wide scatter of frequency-dependent vibration limits exists. It is difficult to compare limiting values of ground vibrations proposed in different standards.1. INTRODUCTIONFor poor ground conditions, placing structures on piles is the most common foundation solution, while sheet piles are widely used to support deep excavations. Piles and sheet piles must often be installed in the close vicinity to buildings, structures or installations in the ground, which can be affected by ground movements and vibrations, (Massarsch and Fellenius, 2014). In many areas, environmental concerns with respect to noise and ground vibrations can restrict or even prohibit driving of piles or sheet piles or reduce the efficiency of installation. The design engineer must prescribe – often at an early stage of a project — the permissible levels of ground vibrations in order to minimize the potential risk of building damage. When seeking guidance from the literature, little or practically no applicable information can be found on how to assess permissible levels of ground vibrations."

Jan 1, 2014

By Charles H. Simmons

Two versions of a VF transceiver to aid in location of trapped miners has been developed and tested. The belt worn model was produced in both transmitter and transceiver configurations. In addition, a quantity of the belt worn models were fabricated using aluminum wire instead of copper in order to reduce unit weight. Ten prototypes of a battery cap model VF transceiver were also fabricated demonstrating further unit size and weight reduction while maintaining electrical performance. Samples of- both versions were tested environmentally and the test data is included in this report. While both versions of the VF transceiver are similar electrically, and are constructed using convential manufacturing techniques, the battery cap model realizes a lower total weight, smaller volume and production cost than the belt worn version. Operationally, the battery cap model assures that the VF transceiver will always be with the miner.

Jan 1, 1981

By J. A. H. Church

The report is too voluminous to be considered in detail within the scope of a single paper, so I will confine my consideration of it to the broader aspects, leaving other members to deal with points of particular interest. The method of presentation leaves one with an uneasy sense of prolixity and confusion of thought; the foreword by the Chairman may well be accepted as a true index of the whole. His argument amounts to this: Recognizing at the outset the futility of divided counsels, it was deemed advisable to arrive at unanimity. To this end, some members subscribed to views to which they do not whole-heartedly assent, thus giving weight to conclusions with which they were at variance. Unanimity cannot be qualified-either it exists or is absent-and, moreover, in the text of the Com-mission I can find no word that unanimity is required. Surely it would have been preferable to have a unanimous report covering such aspects as were acceptable to all members, with minority reports by individual members on such other aspects as were controversial, leaving it to the Government to give such weight to the divergent views as the personality of their sponsors might warrant. In the final analysis the value of an opinion varies directly as the personality of its exponent.

Jan 1, 1926

By Russell J. Miller

A high-pressure intensifier system was designed, constructed and field tested as part of a program to determining the feasibility of applying high-pressure water jets on conventional mechanical rock excavation equipment to increase advance rates. Also developed were a high-volume swivel, capable of transferring the high-pressure water to a rotating cutterhead and manifold system for locating and protecting the jets on the cutterhead. Field tests were conducted in a granite quarry near Skykomish, WA, approximately 90 miles east of Seattle. The concept of improving excavation rates by using water jets to assist mechanical cutting was proven to be successful, with an average increase in excavation mete of 50 to 60%. For some tests, the excavation rate was more than doubled. Machine torque requirements were reduced approximately 25% when the water jets were used. It was suggested this was due to reduced cutterhead friction in the presence of the water jets. A comprehensive economic analysis was undertaken as part of a concurrent study to determine the degree of cost benefits attainable from increased advance rates. Very significant savings were seen to be possible. It was concluded that the basic concept of combining a water jet capability with a mechanical excavating machine is definitely possible.

Jan 1, 1976

By Michael S. Miller

In 1987 and 1988, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 3,100-acre Borah Peak Wilderness Study Area (10-047-004) and a 708-acre parcel adjacent to the north in order to evaluate their identified mineral resources. The study area is located in Custer County, ID, about 18 mi northwest from MacKay. The study area lies along the western foothills of the Lost River Range and is underlain by quartzite, sandstone, shale, argillite, dolostone, and limestone. The Lost River fault, a major active fault, lies along the length of the study area. Large alluvial fans spread out from valleys originating east of the study area.

Jan 1, 1989

By L. B. Hales

Expert control of grinding and flotation plants has been successfully used in the minerals industry since the 1970?s. The earliest of these systems were written in a hard-coded fashion in FORTRAN, BASIC or Pascal. Second generation systems were built using the first experimental expert system shells that were being developed in the artificial intelligence community. Later systems were deployed in expert systems designed for real-time processing plants that also include the ability to model the process with neural network models and optimize setpoint selection through the use of genetic algorithms. [1,2] In spite of the fact that significant performance increases have been achieved using these systems they are not perfect and can be improved. They suffer from the static nature of their rules and to a degree the process models. There is an opportunity to further increase system performance by systematically taking advantage of the tremendous amount of data produced by the expert system to improve the design, the heuristic rules, the model topologies and the use of the models. Data mining refers to extracting or mining knowledge from large amounts of data where the objective is to automatically analyze, classify and summarize the data to automatically discover and characterize trends in it and to automatically flag anomalies. [3] Clearly, modern process control systems are capable of collecting vast amounts of data. Without a doubt, these data contain important information on the operation of our plants and their ultimate optimization. Coupling the information mined from these data with Expert Control Systems should produce more effective control and greater knowledge of the grinding process and the flotation process. Now, with the advent of effective monitoring of entire minerals plant electric consumption it is possible to not only optimize plant production in real-time it is possible to analyze total plant electrical consumption and incorporate it into the plant control logic thereby improving the overall plant economic performance. This is particularly important with the ever more complex power contracts that plants operate under.

Jan 1, 2012

A wide-ranging base of jig data was collected from various types of commercial jigs in 9 coal preparation plants in China, and a complete data analysis was made. It was found that the sharpness ofseparation was very variable, which demonstrates the complex interplay of the many factors which influence jig performance. Tests showed that there exist optimum frequency ranges in each compartment of a jig. Stepwise regression analysis indicated that the sharpness of separation is most sensitive to the intake fraction ofthe air cycle, the frequency, and the feed rate. By means of non-linear curve fitting techniques and statistical analysis, several mathematical models were developed to describe both partition curve and the jig performance, for simulation purposes.

Jan 1, 1986

Nominating Committee.-On the recommendation of the President, the Board of Directors, at their meeting on Apr. 25,1913, appointed the following Nominating, Committee to nominate officers and directors for next year: John Hays Hammond (Ex-President), Chairman. Robert H. Richards Chairman of Boston Local Section. Richard S. McCaffery, . . . . Chairman of Spokane Local Section. Chester F. Lee Chairman of Puget Sound Local Section. Frederick G. Cottrell, . . . . San Francisco, Cal. Charles W. Goodale Butte, Mont. James W. Maleolmson, . . . . Kansas City, Mo.

Jan 5, 1913

By Tianfei Liao

Extensive site investigations revealed that abandoned shallow mine workings exist under a site planned for construction of a major new facility. Since the mine voids were susceptible to collapse, they were stabilized by grouting. After completion of the mine remediation, three types of deep foundations (micro-piles, auger-cast piles, and drilled piers) were considered for this site. Micro-piles spread the load via the bond between the pile and the bedrock. Without significant length socketed in rock, the axial load of auger-cast piles and drilled piers has to be concentrated on end bearing. Although spreading the load is preferable in this environment, economic consideration dictated the choice of drilled piers for construction.

Jan 1, 2009

By Craig Compton

Falls of small pieces of rock from between roof bolts continue to cause fatalities and to injure hundreds of coal miners each year. Roof screen is the most effective way to prevent these incidents, but some mines are reluctant to use it because they believe installing screen can be awkward, expensive and time-consuming. The most common type of roof bolting machine used in mines today is the dual boom, outside-controlled roof bolter. Mines who install roof screen using these machines have developed some machine modifications and techniques to ease roof screen installation. This paper describes some successful techniques and machine modifications that are being used in productive mines to assist with roof screen installation. Since the material handling involved with roof screen installation can expose miners to an increased risk of musculoskeletal injuries, the National Institute for Occupational Safety and Health (NIOSH) ergonomists, designed machine modifications and implemented a series of tests to evaluate roof screen handling procedures for outside-controlled, dual boom roof bolting machines. Roof screen installation can also have a positive economic impact on a mine by reducing the cost of injuries, workers? compensation, required spot or re-bolting, and clean-up of long term travel and belt entries.

Jan 1, 2007

The Australian Centre for Minesite Rehabilitation Research (ACMRR) was established through a mining industry initiative to meet the need of industry, governments and the community for sustainable systems for land affected by exploration, mining and mineral processing activities. The Centre, which is a consortium of the major groups associated with mining rehabilitation research in Australia, has a focus on both strategic research and technology transfer and combines a wide range of multidisciplinary skills covering engineering and the physical and biological sciences. The paper briefly describes the goals, structure, expertise and research and technology transfer activities of the Centre. The major research program areas of waste rock dump and final void stability, acid mine drainage, tailings disposal, and remediation of ecosystem reconstruction are described in the context of national priorities.

Jan 1, 1995

By G. F. Butterworth

The metallographic structures most frequently encountered in rifle barrels, and which are illustrated by the accompanying photomicrographs, fall naturally into two groups, distinguished by the method used to, produce in the stock a physical condition having the requisite properties. The fist group consists of "rolled" barrels; that is, barrels subjected to hot working by rolling in or near the critical range. In the second group, the stock, which is smaller in diameter than the first, is upset to form the butt end and is then heat treated by giving it a quench and a draw. These barrels will be referred to as " heat-treated " barrels. The structure of the rolled barrels resembles closely that of the same steel after annealing. There is the same network of excess ferrite outlining the grain boundaries, but the grains themselves are composed of sorbite rather than pearlite. The grain size is closely related to the rolling temperature. The critical-point curves of this grade of steel, which is approximately 0.50 to 0.60 per cent. of carbon and 1.00 to 1.30 per cent, of manganese, show a single very pronounced point between 1300" and 1350" F. (704" and 732" C.). Barrels rolled within this temperature range give an exceedingly fine grain, shown in Fig. 1. In fact, the grains may be so fine that, at a low magnification, they may be confused with the heat-treated structure shown in Fig. 6. A magnification of 500 diameters, however, will always resolve a rolled barrel into the characteristic structure shown in Fig. 2. As the temperature is increased, the grains are found to be larger. If, on the other hand, the rolling temperature is below the critical range, the structure previous to rolling will not be obliterated, the only effect of rolling being to elongate the coarse sorbite grains in the direction of rolling, Fig. 3. This distortion is greatest at the muzzle. Heat-treated barrels are quenched in oil from above the critical range, which should give a martensitic structure, Fig. 4, but the presence of some troostite in the martensite is frequently noted when the quench has not been sufficiently drastic, Fig. 5. The structure brought about by the subsequent draw is not so striking, though quite as typical. It is sorbitic or sorbito-pearlitic, and under a low magnification appears almost homogeneous, as in the case of fine grains of pepper and salt well mixed together, Fig. 6. This structure is substantially the same for all

Jan 1, 1920

By John McDonald, Peter C. Raleigh, Christopher Dishlip

This paper will discuss how the construction management team and the contractor working together on the City of Los Angeles, North East Interceptor Sewer project, managed information on a daily basis. Data was synthesized from various sources including: inspection, survey, instrumentation, laboratory and the tunnel boring machine data logger systems to produce state-of-the-art reports and graphics which will become industry standard. Special emphasis is placed on how the data is managed and interpreted in a clear and objective manner, permitting the tunneling processes to be carefully monitored and suggesting appropriate action to be taken by the construction management team and contractor.

Jan 1, 2005

By M. V. T. Da Silva, J. C. Harrison

Eldorado Gold Corporation of Vancouver, B.C. owns and operates three gold mines. The São Bento underground gold mine in Minas Gerais State, Brazil produced 105,907 ounces in1997. The La Colorada and La Trinidad open pit, heap leach mines in Mexico produced over 83,000ounces in 1997. With a deteriorating gold market plaguing the industry throughout 1997 Eldorado had to take critical measures at each mine to enhance gold production while lowering cash operating costs. Each mine had its own unique problems to confront. This case study will discuss three distinct courses of action taken at the three mine sites.

Jan 1, 1999

By D. Lawrence, H. Lawrence, G. Saevil

Plant operators in the mineral processing industry have been implementing expert systems for several years now, with the intent to increase production and reduce costs. Most systems have been installed on grinding circuits of some type and have proven that the technology is viable in that application. However, few applications on other processes have been attempted for various reasons, such as lack of reference sites, complexity of the process, lack of suitable measurements and lack of confidence in the technology. The successful application of an expert system on an Alumina Calcining kiln is the first such application in the West Indies Alumina Company (Windalco), and demonstrates how this technology can be successfully applied to other processes. The key objective of an expert system is to optimize the process. To achieve this the process must first be stabilized, followed by optimization of the operating parameters. The steps taken by this expert system to optimize the process are: • Check for abnormal conditions and deal with them using a prioritized set of special actions. • Use a selection of rule blocks to stabilize the process. • Once the process is stable, achieve additional benefits through further optimization of the process. The potential benefits that a user can expect to achieve through installing an expert system can be assessed on the basis that performance will improve from that of an "average operator" to that of the "best operator" performing at his optimum for 24 hours a day, every day. The quantifiable process benefits include: • Increased production • More consistent product quality • Reduced operating costs • Reduced standard deviation of key variables • Consistent plant operation The success of this project was measured in several ways: project implementation, realised economic benefits, and realised non-economic benefits. With a commitment to maintain the system over the long term, the longevity of the system is assured and will become an important part of the Alumina Calcining control strategy at Windalco. This paper discusses the various phases of implementing the ABB Expert Optimizer expert system, what the benefits were and the procedure that is in place to maintain the system to ensure continued long term success.

Jan 1, 2002

By L Torckler, R L. Brathwaite

At Neavesville gold-silver (electrum) mineralisation occurs in steeply-dipping zones of intense fracturing, brecciation and quartz veining within rhyolitic pyroclastics, carbohaceous shales and andesites. Hydrothermal alteration extends over an area of greater than 3 by 1.5 km. In rhyolitic tuffs, highly silicified zones containing quartz-adularia-illite assemblages are flanked by less silicified assemblages composed of albite, illite-montmorillonite and chlorite. The mineralogy and sequence of alteration are comparable with the alteration zones which envelop the steam-producing fissures of the active Wairakei and Broadlands geothermal fields. Primary fluid inclusions in quartz from five fissure veins in the Neavesville field show maximum homogenisation temperatures ranging from 220 - 260¦C and salinities of 0.0 - 1.1 wt per cent NaCl equivalent, which cover a similar range to actual measured temperatures and salinities in geothermal fluids at Wairakei and Broadlands. The age of the rhyolitic pyroclastics and related alteration and mineralisation is probably Pliocene and Neavesville therefore represents a fossil geothermal system. The intensely fractured zones containing the gold-silver mineralisation were probably produced by hydraulic fracturing generated by accumulation under pressure of hydrothermal fluid in blind fault zones. Study of fluid inclusions indicates that hydrothermal quartz associated with electrum was deposited under boiling conditions. High grade electrum mineralisation at Graces workings appears to be localised by reaction of hydrothermal fluid with sedimentary marcasite in black shale.

Jan 1, 1980

By R. W. Fedors, S. T. Green, G. R. Adams, C. Manepally, L. B. Browning

This paper provides estimates of large-scale temperature gradients that can be used to support modeling of natural convection and cold-trap processes in thermally perturbed drifts. Temperature influences estimates of the quantity and chemistry of water contacting engineered components (e.g., drip shields and waste packages) in a potential high-level waste repository at Yucca Mountain, Nevada. Temperature gradients drive natural convection and cold-trap processes, which could affect the distribution, quantity, and chemistry of liquid-phase water contacting drip shields (waste packages).The confluence of high temperatures, liquid-phase water, and high chloride may lead to corrosion of drip shields and waste packages. An overview of the evolution of environmental conditions in thermally perturbed drifts is presented to provide a context for the estimates of temperature gradients. A mountain-scale conduction-only model is used to estimate temperature gradients and temperature differences for a drift located at the center of a potential repository. Thermohydrologic models and heat transfer algorithms are used to evaluate the reasonableness of the conduction-only results. Estimates of temperature using an in-drift heat transfer algorithm account for the possibility of drift degradation and formation of a rubble pile on the drip shield. Temperature differences between the center and ends of the drift are estimated to rapidly increase to 80 °C soon after repository closure. That temperature difference decreases over time to 15 °C after 10,000 years. Local temperature gradients are generally estimated to be less than 0.2°C/m, though the gradients can be much larger near changes in lithology and near the end of the drift. The estimates of temperature gradients do not account for intermediate- and small-scale variations, such as those influenced by differences in heat loads between waste packages, intra-layer variations in thermal properties of the surrounding fractured rock, or localized drift degradation.

Jan 1, 2004

By E. P. Sadowski, R. J. Raudebaugh

A study of micro structural characteristics of a 30 pct Cr, 42 pct Ni, 26 pct Fe alloy has been correlated with its behavior in creep and rupture tests at 1400°, 1600°, and 1800°F. Nitrogen pickup observed at 1600" and 1800°F was associated withfissur-ing of specimens prior to fracture. IN studying the high-temperature characteristics of a nominally 30 pct Cr, 42 pct Ni, 26 pct Fe alloy certain anomalies were observed, namely: The alloy had greater stress rupture and creep strength at 1800" than at 1600° F for time periods beyond 550 hr. As placed in test, this alloy was nonmagnetic. After test, some specimens were found to be fairly magnetic. The gain observed in magnetic response was not solely a function of time and temperature of testing. This is a report of the observations and a recounting of the results of studies made in an attempt to explain the behavior of the material under investigation. MATERIAL AND PROCEDURE All test material was taken from a production size heat of an experimental alloy melted and processed using commercial practice and having the following percentage composition: C Fe Cr Ni Ti 0.05 25.83 30.13 41.59 0.41 Al Mn Si S Cu 0.42 0.75 0.45 0.011 0.34 The material was tested in two conditions, namely mill-annealed and grain-coarsened. Mill annealing, which consisted of heating to about 1900° F in a continuous furnace for about 30 min and air cooling, gave a grain size of ASTM 8 and finer. To produce the grain-coarsened condition, mill-annealed material was soaked for 2 hr at 2050°F in a laboratory furnace and air cooled. This resulted in an ASTM grain size of 4 to 5. Rupture tests were carried out at 1400, 1600, and 1800° F in accordance with ASTM procedures. In tests where only rupture life and elongation at fracture were determined, specimens of 0.252 in. diam and 1 in. gage length were used. In tests where creep curves were obtained, specimens were of 0.375 in. diam and 4 in. gage length. Several of the tests under relatively low stress were discontinued short of rupture. Three low-stress tests are still in progress at this writing. Structural changes which occurred during testing were determined from examination of the tested specimens by light microscopy and X-ray diffraction. Diffraction pattern recordings were made with a diffractometer using copper radiation on samples heavily etched in a picric-hydrochloric

Jan 1, 1960

By Stephen C. Tadolini, Dennis R. Dolinar

The risk of injury caused by minor roof falls continues to increase in underground mining. Most ground control injuries result from small rock falls that occur in a supported area, but do not involve the failure of the support system. In the roof, these are the "skin failures" that occur between previously installed primary or secondary bolting systems. To minimize skin failures and the associated accidents, several devices were designed and tested in the laboratory to maximize stiffness, minimize material thickness and weight, and ease material storage and handling on roof bolting machines. The goal of this project was to design and evaluate devices that can be installed with traditional primary or secondary roof supports, and that are easy to handle/install under temporary or previously supported roof.

By Klaus Tietz, Hamish Adam, John Selby, Ian Glazier, Brian Sinfield

"Room-temperature tunable diode laser (TDL) analyzers are gaining in acceptance for highly critical safety monitoring applications in a variety of industries. This paper describes the testing, evaluation and deployment of a laser-based hydrogen cyanide monitoring system at the Campbell Complex of Goldcorp’s Red Lake Gold Mines in Balmertown, Ontario, Canada.A trial, single channel installation was followed by a staged multi-channel installation. Unexpected technical issues with the multi-channel installation were addressed and resolved.INTRODUCTIONLaser-based gas detection has several advantages over existing gas detection techniques (Ballangrud, 1993; Silver, 1992; Bomse, 1995; Table 1). For practical purposes, lasers generate light at a single wavelength. Room temperature tunable diode lasers (TDL) emit light in the near infrared (NIR) part of the electro-magnetic spectrum. Many gases of interest, including HCN, NH3 and others, absorb energy in the near infrared (NIR). Each gas has a unique absorption signature, or spectrum, made up of a large number of individual “absorption lines”. A TDL can be tuned to select a single absorption line of a target gas, which does not overlap with absorption lines from any other gases. Therefore, laser gas sensing is selective and does not suffer from interference from other gases. The single-wavelength nature of laser light also means that laser gas analysers have a linear response over a wide dynamic range.Tunable Diode Lasers (TDL) generate only a few mW of power. However, all this power is concentrated at one wavelength, the wavelength where gas absorption occurs, resulting in high signal-to-noise ratios and short response times, typically of about 1 or 2 seconds (Ballangrud, 1993). This also means that long path lengths can be used, enabling accurate measurements of very low concentrations, even with weakly absorbing gases. Tunable Diode Lasers provide all the advantages of other semiconductor devices: they are small, solid-state devices, operate at room temperature, and have long-term reliability (over 15 years). Currently, they can be obtained for any wavelength throughout the NIR (700nm to 2000nm). Because many gases absorb in the NIR, the technique is widely applicable."

Jan 1, 2011