Search Documents

By R. O. Dannenberg

The Bureau of Mines conducted laboratory batch and small-scale continuous tests to remove traces of dissolved molybdenum from water simulating waste discharged from a molybdenum concentrator, Molybdenum concentrations, initially ranging from 2 to 10 ppm, were decreased to 0.5 ppm or less by coprecipitation of the molybdenum with freshly precipitated ferric hydroxide" The precipitate was separated as a froth by dissolved-air flotation for subsequent disposal. Although the treated water met current environmental standards for contained molybdenum, contained particulate iron might have to be removed by filtration for the water to be acceptable. Estimated costs for treating concentrator effluent water were 55 cents, 57 cents, and 64 cents per 1,000 gal at initial molybdenum concentrations of 2, 4, and 10 ppm, respectively.

Jan 1, 1982

By M. J. Sapko

From 2001 to 2007, the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH) conducted studies to develop alternative methodologies to full-scale explosion testing for deter-mining the ultimate strength of mine seals. As a result, the PRL developed and proposes an alternative seal-strength evaluation method based on a hydrostatic pressure-loading concept. The researchers suggest pressure loading a seal using water to twice the expected dynamic design load. The hydrostatic chamber test offers a means of validating seal designs, establishing appropriate resistance functions and determining the ultimate strength of seals through testing to failure. This article contrasts the full-scale explosion and hydrostatic testing of mine seals using a simple dynamic system model and principles.

Jan 1, 2008

By Kelsall D. F, Trahar W. J

The size by size batch flotation behaviour of copper activated sphalerite from synthetic mixtures with quartz was determined. In terms of recovery of sphalerite, the size fractions could be grouped into coarse, intermediate, and fine ranges. The behaviour of the coarse and fine ranges was significantly poorer than that of the intermediate range in both the extent and rate of flotation.Each size fraction had a fast and a slow floating component.The main effect of changing the copper sulphate addition was to alter the proportion of any size fraction which was fast floating. No correlation could be found, between the amount of copper on the spha:lerite andeither the flotation rate of the mineral or the amount of copper added to the system. It was found that fine particles did not appear to consume greatly disproportionate amounts of copper sulphate during conditioning. A modified conditioning procedure was found to lead to a higher rate of flotation and recovery of coarse sphalerite and to make poss1ble substantial savings of copper sulphate.

Jan 1, 1975

By Michael E. Meadows

The results of tests to determine the .regional applicability of four synthetic unit hydrograph models are presented. The SCS curvilinear (Haan), SCS single triangle, Williams and TVA double triangle unit hydrograph models were tested on 271 events from 38 USDA experimental watersheds in 14 physiographic provinces. Though inconclusive due to the limited number of events analyzed, the results indicated a regional tendency for each model, with the SCS curvilinear unit hydrograph method generally performing best overall. It outperformed the SCS single triangle by predicting better shape; they differed less than 2 percent in time of peak and peak rate predictions. The Williams model performed well at Oxford, Mississippi and Coshocton, Ohio, which suggests it may be applicable to surface mined lands within the Northern and Central Appalachian Plateau and Texas coal producing regions. The TVA model is applicable to the Appalachian Plateau, specifically the Cumberland Plateau. A second test using only the SCS curvilinear unit hydrograph on 11 small watersheds and 50 events was conducted to investigate the effect of the excesss rainfall pattern on simulation results. A Green and Ampt infiltration model was coupled with the SCS unit hydrograph model to determine if peak rate and timing errors noted in the regional test could be minimized with an alternate to the SCS curve number model for determining infiltration losses. The results confirm the curve number model is the better approach to determining the excess rainfall pattern for unit hydrograph simulation.

Jan 1, 1983

By Robert C. Rabeler

Soil and Materials Engineers, Inc. (SME) has utilized drilled cast-in-place (D-CIP) piles on a number of projects in the midwest. These foundation systems have typically consisted of drilling an 8 to 9-inch diameter borehole with a rotary type drill rig or driving a casing with a small hammer. A structural steel member is installed in the center of the excavated space, and the borehole or casing is grouted to complete the installation of the D-CIP pile. This type of piling system has also been called: mini-pile, micro-pile, or drilled-in pier. The capacity of these piles varies depending upon subsurface conditions, as well as the structural capacity of the pile. The structural capacity can be modified based on the size and yield strength of the structural steel member. SME has used the D-CIP piles for underpinning of lightly-loaded structures for a number of years. Steel brackets can be welded to the structural steel member in the center of these piles, and the bracket extended underneath existing foundations to provide proper foundation support. D-CIP piles have also been used for new construction where access was limited. Recently, SME had the opportunity of providing design as well as construction monitoring services for a unique project where these piles were used, but at much higher capacity. The project involved adding seven additional floors on top of a five-story building (total of 12 stories). New columns were extended through the existing building to support the new floors. Access to construct foundations was available to one level of underground parking beneath the structure, as well as to a basement area. Access required equipment to travel through a 3-foot wide hallway. A special duplex drilling machine was used to access the foundation locations and to install the piles in a limited headroom condition. Eight-inch diameter D-CIP piles were extended to a depth of approximately 40 to 50 feet below grade and socketed into a dense clay till or sandstone, and No. 18 or No. 20 threaded bars were installed in the center of these piles. The design pile capacity was as high as 190 kips and were verified by a compression load test. The load test was performed with limited access and headroom. These piles were installed by Spencer White and Prentis Foundation Corporation (SWP). For conditions where rock or hard soils are encountered at reasonable depths, D-CIP piles can provide working load capacities comparable to larger driven steel piles. The ability of the equipment to access very restricted areas, combined with the high capacities results in a very attractive solution to a number of difficult foundation problems.

Jan 1, 1999

By James L. Poole

The gold and silver markets from the late 1960's to the present are reviewed and the outlook for these metals in the 1980's is presented. Included in this discussion is a summary of the basic supply and demand balance for gold and silver since the mid-1960's. an explanation of the price formation for the metals, some of the relationships between the prices of these metals and selected economic parameters, and how these factors affect the outlook.

Jan 1, 1981

Horizontal holes are drilled underground into coalbeds to control methane flow from ribs and active face areas and to make gas pressure measurements in coalbeds. Gas pressure measurements are made by drilling the same hole incrementally. After each increment, the hole is filled with some type of packers and allowed to reach equilibrium before a gas pressure reading is taken. As the length of hole increases, more packers are required to effect a seal and obtain a reliable pressure measurement. Problems have been encountered in obtaining satisfactory packer seals due to the friable nature of the coalbed. New methods of packing the holes must be used. Therefore, this project was established to evaluate materials and develop a new technique in which a semiliquid and/ or rigid type grout could be placed in the hole to provide satisfactory sealing.

Jan 1, 1972

By John C. Gagliardi, Walter K. Utt

The U.S. Bureau of Mines, in cooperation with Carter Mining Co., conducted vibration tests of four off-road vehicle seats. The purpose of the tests was to determine which seat provided the best vibration attenuation under laboratory conditions. Laboratory tests were constructed to simulate the mining vibration environment within the limitations of the test equipment. The acceleration test levels and corresponding response of the seats were low compared to IS0 2631's fatigue-decreased-proficiency time limits. Two of the seats employed mechanical suspensions and two seats employed air suspensions. The seats were tested using a 22,241-N (5,000-lbf) electrodynamic shaker. Mechanical suspension seats were tested with various preload-to-mass ratios (PMR's) and cushion densities. Air suspension seats were tested with various air pressure levels and seat cushion densities. Air suspension seats provided good vibration attenuation if pressurized greater than 552 kPa (80 psi). Mechanical suspension seats' attenuation performance decreased if the PMR exceeded 9.8. Seat cushions of lower density provided less vibration damping.

Jan 1, 1993

By C. Patel, George H. Hope

"INTRODUCTIONThe Hemlo area is located in Northern Ontario, some 350 km east of Thunder Bay along highway 17. Hemlo is Canada's largest, recent discovery of gold ore. Three companies, Lac, Noranda, and Teck are currently developing mines and processing facilities in the area. A combined milling capacity of approximately 10,000 tonnes per day will ultimately be available in the area. The gold yield will be between 750,000 to 1,000,000 ozs. per year. This will slightly more than double Ontario's gold production but only represents 2.5% of the total world gold production.Lac Minerals Ltd. is substantially committed to the gold mining business. Lac currently operates four (4) gold mines and mills and produces 300,000 ozs. per year. Lac's Hemlo development will put the company in the position of number one gold producer in Canada.The Lac Hemlo ore body has an estimated reserve of 37 million tonnes at 6.2 g/t. The mining will take place at an initial rate of 3,000 t/d commencing in the first quarter of 1986. The mine and plant will be expanded to 6,000 t/d in 1988. At this capacity, Lac will be the largest producer in the Hemlo area.1. GEOLOGYThe orebody is divided into two (2) zones for mining purposes. The 'A' Zone is to the east and dips to the Northeast from surface to 300 m below surface. This zone has a strike length of 250 m to 300 m at an average width of 20 m. The upperpart of the zone will be mined by open pit and the remainder from underground. The 'B' Zone, to the north west of the 'A' Zone, although lined up is not necessarily an extension of 'A' Zone. 'B' Zone has a known strike length of 600 m and is open to depth and along the strike. It is over 70 m wide in the core. This zone holds most of the property's known reserves. 'C' Zone with narrow gold zones is under exploration in the south west portion of the property."

Jan 1, 1985

How Particles Stick to Bubbles - The Influence of pH and Hydrophobicity in Flotation

Sep 13, 2010

By S L. Birch, M D. Raven

X-ray diffraction (XRD) is a well-recognised, invaluable tool to provide detailed mineralogical analysis on a wide range of applications. However, despite the wide use of XRD in many industries, there are currently few recognised standard methods for quantitative XRD analysis and none for the analysis of iron ore materials. An initial step towards preparing a standard method for XRD analysis of iron ores was to assess the current level of precision achievable by practitioners of the technique by organising an international round robin. Six Australian chemically certified iron ore reference materials were distributed to over 100 international participants. A summary of over 120 data sets from more than 80 participants is presented. Results show that a bewildering array of techniques for sample preparation, data collection, phase identification and quantification were used. The reported values for the main components (ie hematite, goethite, quartz and amorphous content) show not only extensive variability between participants but also within participants’ results for those who submitted multiple data sets. The disappointing low level of precision exhibited for a relatively simple mineral phase system indicates a strong requirement for development of a standardised procedure.CITATION:Raven, M D and Birch, S L, 2017. Summary of results of an international X-ray diffraction round robin for mineralogical analysis of iron ores, in Proceedings Iron Ore 2017, pp 599–604 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Claude Deveau

"Studies on the performance of Falcon batch type concentrators treating ultrafine tantalum at Tanco have revealed that very fine heavy minerals are concentrated within certain areas of the concentrate bed. This information led to the design of a bowl which would allow entrapped lighter low grade particles to escape while providing more space for heavier particles to be recovered in the bed.Numerous tests were then completed with a modified batch-type and non-fluidized Falcon bowl in which the diameter of the discharge lip was adjusted downward manually in steps. This allowed for the gradual building of a higher grade concentrate bed.This work ultimately led to the design of a new Falcon with an automated continuously variable lip. In April 2005, Tanco commissioned the first Falcon UF600.This paper will discuss laboratory scale results and also plant performance of the Falcon’s UF technology.INTRODUCTIONTantalum Mining Corporation of Canada, also known as Tanco, is a wholly owned subsidiary of Cabot Corporation based in Boston, Mass. Operating since 1969, the underground highly mechanized room and pillar operation produces tantalum, lithium and cesium minerals and is located a 2 hour drive east-northeast of Winnipeg Manitoba, Canada.At Tanco, tantalum is recovered using conventional gravity concentration, enhanced gravity concentration and flotation. This paper will discuss how the need for improved equipment to treat very fine tantalum particles was filled by a machine which was modified to the point of creating a completely new technology.In November 2003, Tanco began the investigation for the potential use of a high g-force smooth walled concentrator for treating ultra fine tantalum produced by its flotation circuit. Until then, the tantalum flotation concentrate had been treated by a circuit which consisted of a Mozley Multi-Gravity Separator 902 (MGS), a Mozley MGS 900 and a Bartles cross belt concentrator. Through QemScan analysis, it was found that the majority of the losses from this circuit were of an extremely fine nature which exceeded the recovery limits of equipment on hand. Mean particle size of the tantalum losses was less than 10 µm."

Jan 1, 2006

By H. F. Fuls

The quality of Pregnant Leach Solution (PLS) at Skorpion Zinc is of utmost importance for efficient operation of the Solvent Extraction (SX) Plant. Suspended solids in the PLS forms CRUD in the settlers, resulting in reduced zinc transfer capacity and increased impurity carry over to Electrowinning. The Ishigaki Fibre-Wakishimizu filter (fibre media rapid filtration equipment) has been identified as polishing filter that potentially could remove solids from the PLS of Skorpion Zinc. A pilot unit with 20m³/h capacity was tested on site over a period of 9 months under plant operating conditions in the refinery. The FW filter produces a clear filtrate, acceptable for the Solvent Extraction. Turbidity is improved by 72%. Gravimetric analysis indicates a 47% removal of solids. However, the gravimetric method is biased by a co-precipitation of saturated salts during the analysis. Filter media is blinded by the Skorpion Zinc PLS solution, as result of suspended solids and process chemistry. The media could not be regenerated to acceptable conditions. Further testwork to investigate the impact of process solution chemistry modification on blinding is undertaken. Based on the outcome of this investigation a final decision on the FW filter can be taken.

Jan 1, 2008

By D Craw, P Upton

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Southern Alps of New Zealand and the mountains of Taiwan are both young transpressive orogens characterised by rapid uplift and exhumation, high heat flow and vigorous surface processes. Comparing and contrasting the two provides an ideal framework through which to explore the structural and lithological controls on fluid and gold mobility during collisional deformation. Both have two fluid flow systems centred about their drainage divide with shallow topographically-driven meteoric water above a deeper flow system dominated by mineralising rock-exchanged fluids. Despite similar tectonic settings, the distribution of heat flow, hot springs and veins in the two orogens are different. Taiwan has higher heat flow, distributed hot springs and localised veining whereas the Southern Alps have a narrow heat flow anomaly, localised warm springs and widespread veining. We use three-dimensional numerical models to evaluate key parameters that affect fluid flow and gold mineralisation. Models show that differences in crustal strength and thickness affect the locus, scale and rate of crustal fluid flow and hence influence gold deposition at a variety of scales. We explore how surface topography can lead to localised changes in the stress state, facilitating the switching of principal stresses and hence vein orientations.CITATION:Upton, P and Craw, D, 2015. Modelling structural and lithological controls on the mobility of fluids and gold in orogenic belts – examples from New Zealand and Taiwan, in Proceedings PACRIM 2015 Congress, pp 189–192 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

Geological information is essential for a diversity of public and other purposes, including land use planning, hazard mitigation, and the exploration and sustainable use of natural resources. This is especially important in New Zealand, where the complexity of the geology is due to its position on an active plate boundary - the ultimate cause of earthquakes, mountain building, subsidence and volcanic activity. The geological setting also controls the origin and distribution of New Zealand's varied mineral and energy resources. Providing information about the origin, quality and quantity of mineral resources has long been seen as a key function of national geological organisations such as the Institute of Geological and Nuclear Sciences. Such information is essential for wise land-use decisions under the Resource Management Act. One of the major goals of the Institute is to quickly and effectively disseminate research results to interested users. The most effective and internationally accepted method of presenting geological data is by means of geological maps, which show the distribution of rock types and structural features at the surface. Most countries have ongoing gelogical mapping programmes, and in recent years the need for up-to-date, reliable information has led to a trend to accelerate basic geological mapping (eg US National Geological Mapping Act 1992; Australian National Mapping Accord 1990; Plan 2000 in the UK). Over the last 25 years, the Institute of Geological and Nuclear Sciences and its predecessors (NZ Geological Survey and DSIR Geology and Geophysics) have concentrated on detailed mapping of priority areas selected on the basis of economic and scientific interest. This has included remapping of Nelson-West Coast and Coromandel, regions with high mineral potential, for which 1:63 360 or 1:50 000 maps have been prepared.

Jan 1, 1994

By S. E. Bretherton

This title introduces the subject I wish to describe to my fellow members, very few of whom, I 'hope, have ever had as much trouble with the smelting of ore containing much zinc, either in the lead blast furnace or the matting furnace, as circumstances have forced upon me: First, for several years in Leadville, Colo., after the sulphide ores containing zinc had been developed with greater depth and were sold to the intereats with which I was connected for smelt-ing in the blast furnace for the recovery of the lead, silver, and gold; then, in New Mexico and Arizona, where the principal source of ore supply for our custom smelter was from miners who sent most of their product in the form of concentrates, which we briquetted and smelted in the blast furnace, producing a matte containing copper, silver, and gold, for which we were paid; together with some zinc and lead, which was penalized if in excess of a maximum base set by the refinery to which we sold our copper matte; last, but not least, my experience in Shasta county, Gal., where for the sake of recovering $13 per ton value in copper, silver, and gold, I have smelted ore containing as high as 40 per cent. zinc (the last 18,951 tons smelted averaged 15 3/10 per cent. zinc) which we not only lost, but which it cost us money to lose. After such an experience, and knowing that, instead of being worth only $13 per ton, such 15 per cent. zinc ore should be worth about $30, including zinc at the present market value, the question of recovering the zinc in a profitable manner from such ore became very interesting to me. During several years' time I sent samples, of from 5 to 1,200 lb. each, to be tested by the different best-known zinc-recovery plants, and experimented with several processes proposed by others for the treatment of such ore, with but little encouragement, until I

Jan 1, 1914

By Frank W. Luerssen

Introduction "Austerity" is perhaps an overly generous description of the past three years in the American steel industry. Steel plants operated at an average of only 57% of their capability in 1982-84. The dismal losses for last year are still being totaled. But during the two years before this period, American steelmakers recorded an aggregate net loss of a staggering $6.8 billion. Steelmakers responded by closing numerous marginal facilities. And production capability was cut by 13.6 Mt (15 million st). Capital expenditures still averaged $2 billion annually. But this was inadequate to maintain the existing base of steelmaking facilities. The general economy experienced a satisfactory recovery during this period. American steel, however, continued to suffer from a lagging recovery in the capital goods sector. This was due to record penetration of its domestic market by imports and from very weak realizing prices on the volume that was available. In addition to the direct influx of offshore steel products - which itself depressed prices - the industry also became painfully aware of the growing importance of "indirect" imports. These came in the form of steel-containing producer and consumer durables. Industrial equipment and autos fabricated from foreign steel accounted for the equivalent of 6 Mt (6.5 million st) of lost market opportunity for domestic steel-makers last year. That is over and above the 23.5 Mt (26 million st) of direct steel imports. Given these factors, Inland Steel was not spared from the threeyear downpour of red ink. Despite its record of continuing modernization in steel, our single-plant location in the world's best steel-consuming market, and the high proportion of consumer durables related products, such as cold rolled and coated sheet in our mix, Inland suffered aggregate losses of $277 million during the 1982-84 period. Strategic Planning The foregoing establishes a perspective - a base from which we have restructured our view of the steel industry, and of our own role within that picture. Until possibly two years ago, this present weakness in steel demand was viewed around the world as an aberration, eventually to pass. By contrast, it is now recognized that austere times are the normal steel environment. The topic here is management of resources. This implies an emphasis on strategic planning. It is worthwhile to examine some of the more critical assumptions that were driving strategies among a number of steel companies just before the 1980s. Those projected characteristics of the future steel environment were arrived at through painstaking analysis. They were carefully and heavily quantified and were generally shared by outside observers and our peers within the steel industry. • First, the assumption was made that domestic steel demand would continue to grow at an average rate of 2% per year. • Second, it was assumed that this growth in the American market would continue to be filled predominantly by US mills. It was believed that increases in steel and steel-related demand overseas would absorb much of the ominously growing capacity of third

Jan 6, 1985

By F. Haessner, M. Wilkens, U. Jakubowski

ThOUGH at present there is a wide range of possibilities for the quantitative determination of preferred orientations, pole figures of identical specimen material have not been determined by different methods as yet.''' In this paper a comparison of (Ill), (200), and (220) pole figures is presented which were obtained from a 95 pct cold-rolled high-purity cop- per sheet (99.9998 pct Cu), by three different methods. The three methods are: a) The combined X-ray reflection-transmission technique of plane samples by schulz3 and Decker, Asp, and Harker. 4 A Siemens texture goniometer was used. The experimental details are described elsewhere. 6 b) The X-ray reflection technique of spherical samples by Jetter and Boric.' A Siemens texture goniometer with some modifications was used. The samples were prepared by sticking 140 polished sheets together with an adhesive and machining a sphere (20 mm diam).* Additional

Jan 1, 1967

By Chaoxun Zhao, Daniel Tao, Craig Blue, Narendra B. Dahotre, Rick Honaker, Bhupendra K. Parekh, Hongyang Han

Equipment wear and corrosion have significant adverse impacts on the operating cost and efficiency of mineral processing plants. In this project advanced surface enhancement technologies are being investigated to decrease the wear and corrosion rate of metal surface. Enhanced metal surfaces are achieved through surface conversion, enrichment, and coating by use of advanced High-Density Infrared (HDI) and other technologies. Studies have been done to determine the effects of process parameters on surface properties and identify optimum conditions. The microstructure of the enhanced metal surfaces was characterized by SEM, EDS, and microindentation. Laboratory wear testing was carried out to investigate the wear performance and the viable coating candidate was determined.

Jan 1, 2005

By Raymond Philippe

Background ?Hatch Water has worked with most major mining companies in Chile on water supply and optimization projects ?Many(copper) mining projects are located in Northern Chile, which hosts the driest desert on earth Water supply options in Northern Chile ?River ?Availability/Rights ?Well(Brackish) Water ?Availability/Rights ?Municipal Wastewater ?Water rights ?Volume ?(Desalinated) Seawater ?Infinite source ?Cost depends on distance and altitude ?Recycling/Reutilization ?Water losses All these options present water quality issues

May 1, 2009