Search Documents

By A. D. Davis

Limestone-based material shows great promise for removal of arsenic from water. In laboratory tests, it has removed more than 95% or arsenic and more than 99% of cadmium and lead. In addition, the waste material appears to be suitable for recycling or disposal in an ordinary landfill. However, the efficiency of limestone for arsenic removal could be improved. Recent research has shown that iron treatment of limestone can enhance its arsenic-removal efficiency greatly, increasing its attractiveness as an alternative to other methods.

Jan 1, 2012

By Fabian Kirsch

Cyclic behaviour of axially loaded piles has been an issue since studies revealed that the capability to transfer skin friction into the ground is highly depending on the level and the number of load cycles the pile is subjected. It has been shown that degradation of skin friction due to axial cyclic loading leads to accumulating displacements and a severe reduction in pile capacity. In Germany the DIN 1054 as well as the Recommendations of the Working Group 2.1 ?Piles? of the German Geotechnical Society (EA-Pfähle) require the consideration of cyclic loading for the assessment of both the displacements and the capacity. Up to now no broadly accepted design method exists, which enables the engineer to give a reliable judgement on the pile capacity under axial cyclic loading and the displacements respectively. Instead numerous design charts make it possible to distinguish between stable and instable loading levels in order to ensure a design on the safe side. A newly developed design approach based on engineering models is presented which delivers a calculation algorithm for the remaining axial pile capacity after a defined number of load cycles to allow for the analysis of stability of the foundation. Furthermore the computation of accumulating displacements is made possible. The results are verified with pile load tests undertaken at Dunkirk, France and showed that the axial capacity after cyclic loading calculated with the newly developed design approach predicts actual capacity with an accuracy of ±20%.

Jan 1, 2011

LIST OF THE MEETINGS OF THE INSTITUTE AND THEIR LOCALITIES FROM ITS ORGANIZATION Transactions Number Place Date Vol Page 1 Wilkes-Barre, Pa May, ?71 1 3 2 Bethlehem, Pa August, ?71 1 10 3 Troy, N Y November, ?71 1 13 4 Philadelphia, Pa February, ?72 1 17 5 New York, N Y May, ?72 1 20 6 Pittsburg, Pa October, ?72 1 25 7 Boston, Mass February, ?73 1 28 8 Philadelphia, Pa May, ?73 2 3 9 Easton, Pa October, ?73 2 7 10 New York, N Y February, ?74 211 11 St Louis, Mo May, ?74 3 3 12 Hazleton, Pa October, ?74 3 8 13 New Haven, Conn February, ?75 3 15 14 Dover, N J May, ?75 4 3 15 Cleveland, 0 October, ?75 4 9 16 Washington, D C February, ?76 4 18 17 Philadelphia, Pat June, ?76, 5 3 18 Philadelphia, Pa October, ?76 5 9 19 New York, N Y February, ?77 5 27 20 Wilkes-Barre, Pa May, ?77 6 3 21 Amenia, N Y October, ?77 6 10 22 Philadelphia, Pa. May, ?78 6 18 23 Chattanooga, Tenn May ?78 7 3 24 Lake George, N.Y. Oct. ?78 7 25 Baltimore, Md. Feb. ?79 7 26 Pittsburgh Pa, May ?79 8 27 Montreal, Canada Sept, ?79 8 28 New York, N.Y. Feb, ?80 9 29 Lake Superior, Mich Aug, ?80 9 30 Philadelphia, Pa. Feb, 81 9 31 Staunton, Va May, 81 10 32 Harrisburg, Pa Feb, 81 10

Jan 1, 1952

By C. W. Morris

This study was performed for the U.S. Bureau of Mines. An existing computer simulation of a dragline was modified to simulate a dragline dumping into the hopper portion of a cross-pit conveyor system. This revised computer model was then used to study four proposed cross-pit conveyor systems. Parameters such as dragline position, hopper position, and digging procedure were varied to maximize the dragline production. This performance was compared with the conventional side-casting spoil method. I t was concluded that the cross-pit conveyor systems were competitive with the conventional side-casting technique.

Jan 1, 1977

By Q. J. Browne, M. A. Miller

Silver Bell produces about 22,000T of fine copper annually from low-grade chalcocite and oxidized copper ore that is recovered by sulfuric acid leaching and SX-EW processing. The current mineable reserves are 146 million short tons averaging 0.39% Cu, at a 0.15% cutoff. Silver Bell utilizes two types of mining methods to develop the low-grade reserves: (1) a conventional blast, load and haul method for run-of-mine leach ore, and (2) rubblization of material on the margins of existing pits. Rubble leach ore is blasted, terraced with a bulldozer, and leached in place. Mining and/or rubble leaching is currently active in four separate pits. Laramide-age intrusive rocks host porphyry copper mineralization at Silver Bell. Quartz monzonite porphyry dikes and stocks, mafic-poor equigranular granite (alaskite), and sub-volcanic dacite porphyry are the predominant host rocks. Most of the ore currently mined comes from near-horizontal enrichment zones containing veinlets and disseminated grains of pyrite and chalcopyrite rimmed by chalcocite. Conversion from a milling operation to a leach only operation allowed for a much lower cutoff grade than was historically used at Silver Bell. Mine geologists were able to increase copper resources by drilling exploration targets that were previously interpreted to provide lower-grade mineralization below cutoff-grade for milling. Geologic parameters that effect the distribution of rubble and mineable leach ore include: ore grade and thickness, variable alteration styles in intrusive host rocks that affect fragmentation during blasting, acid consuming carbonate wallrocks (reactive skarn) which influence leach solution pH, solution flow paths and drainage, presence of leachable oxide mineralization in non-reactive skarn, and depth to hypogene mineralization which is currently uneconomic. Geologic parameters are used to predict rubble bench limits, vary blast hole spacing for consistent fragmentation, and correct errors in mineral zone classification based solely on blast hole assays. An expansion-drilling program has identified approximately 150 million tons of new leachable copper resources with an average grade of 0.35% Cu.

Jan 1, 2002

Models are used in engineering to reproduce reality as faithfully as possible so that the expected response of a system for given actions or inputs can be determined. In the field of rock engineering, both empirically based and numerical models are widely used to determine the likely response of the rock surrounding excavations. Many of the empirical models are developed from statistical analysis of case histories or from direct observation; however, empirical models are limited because they should be used only within the range of conditions of the observational database. Synergy exists between empirical and numerical models, because empirical models can be used to calibrate and validate numerical models. The empirical approach can benefit from the capability of numerical models to investigate specific mechanisms, which would not be possible using observations alone. Two cases are presented in which the synergy between empirical and numerical models is demonstrated. The first case examines the analysis of discontinuity effects on the strength of slender pillars in limestone mines, and the second case evaluates the effects of stress orientation on coal mine entry stability. It is concluded that numerical model calibration and verification comprises an important first stage in the successful application of models in rock engineering design. Application of numerical models allows mechanisms and interactions of various parameters to be analysed, greatly improving the understanding of the system. The improved understanding can be used to extend the application of empirical design methods, resulting in improved safety and efficiency of rock engineering designs.

Jan 1, 2014

By Shemek Oginski

The 5 km (16,194 lf) of 6.1m (20 ft) diameter TBM driven tunnel built by the J.F.Shea Co. will serve as sewage overflow storage. The TBM tunnel and four connecting tunnels excavated by drill and blast methods in hard granite will remain unlined. Based on the Geotechnical Baseline Report (GBR), the Contract documents provided a design with no required pattern of rock bolts, no probing, no pre-excavation or consolidation grouting, and lastly, no final lining of the tunnels was deemed necessary. This paper will provide a general overview of these topics with the emphasis on the actual ground conditions encountered versus the projected conditions provided in the GBR and how the GBR reflected the design of the project. Proposed modifications to the temporary and permanent ground support will be presented and the necessity of probing and pre-excavation grouting will be evaluated.

Jan 1, 2005

By A. P. Gize, J. F. W. Bowles, D. J. Vaughan, S. J. Norris

Paper presented at the IAGOD international symposium on mineralization related to mafic and ultramafic rocks held in Orleans, France, 1-3 September 1993. Geological evidence from tropical laterites indicates clearly that platinum group metals are taken into solution and precipitated to form grains larger than those in the source rocks. Platinum and palladium move differentially in the surface environment, with Pt partitioning into soils and eluvial or alluvial deposits while Pd remains more mobile in natural waters. Natural organic acids, particularly humic acid, can interact with platinum-group elements and concentrate them even in areas where their content in rocks is very low. Experimental work has confirmed that Pt and Pd can be taken into solution by humic acid at room temperature and in geologically short time-spans. Solubility and deposition may be controlled by physicochemical conditions, reaction kinetics or an adsorption effect, or there may be two competing reactions, solubilisation assisted by organic matter and a kinetically slower metal precipitation

Apr 1, 1994

By Clarence A. Wright

The Missouri-Kansas-Oklahoma lead and zinc district, better known as the Joplin district, includes the mines in southwest Missouri and in those parts of Kansas and Oklahoma that are directly adjacent. (See PI. I.) This report of investigations carried on by the Bureau of Mines gives the methods used in mining and milling and indicates in some detail the conditions that affect the efficiency of those methods; it does not attempt to discuss the geology of the district, except incidentally, as this has been described in numerous reports by several geologists. Some of the more important recent publications are those of the United States Geological Survey by Smith and Siebenthal, a Bain, b and also those of the Missouri State geological survey by Buckley and Buehler." Other reports are those by Schmidt and Leonard," and Winslow,e of the Missouri geological survey, by Haworth and Crane,! of the Kansas geological survey, and by Jenney.g Although the lead and zinc ores are closely associated, the proportion of zinc ore mined at present is far greater than in former years. For this reason and because the losses in milling zinc ores are proportionately greater than in milling those of lead, the zinc ores are here given most consideration. Only the mines and mills actually examined and tested are discussed in detail, statements of results being restricted to the mines in general, with no special reference to anyone mine. Several mill tests were made to determine in a general way the efficiency of the milling practice in this district and to discover at what stage of the process the losses were greatest. Making these mill tests proved difficult,for, because of the arrangement of the mills and the necessity of estimating the tonnage treated, systematic mill testing and sampling can be done at only a few plants. Many tables giving results of mill tests and screen tests have been omitted because they would serve only to emphasize the important points shown by other data given. The writer has tried to bring out the possibilities of making certain improvements that would effect a greater saving, and has endeavored to avoid the use of technical terms and phrases in order that all statements may be clear and easily understood.

Jan 1, 1918

Exploring the Breakage Environment in Mills with Discrete Element Methods

Sep 13, 2010

By Don M. Coulter

"INTRODUCTION Bauxite, in Appalachian Alabama, occurs in the Rock Run and Goshen Valley districts in Cherokee County; in Nences Creek Valley near Jacksonville; near Anniston in Calhoun County; north of Fort Payne in DeKalb County; near Ashville in St. Clair County; and near Talladega in Talladega County.In February 1942, Preston E. Cloud, Jr., assistant geologist, Federal Geological Survey, began a study of these bauxite deposits and the geology relating thereto.The Bureau of Mines established field headquarters at Piedmont, Calhoun County, in July 1942. Mineral agreements covering a total of 11,097 acres were executed with 15 landowners in the Rock Run district; 38 in the Goshen Valley district, covering 7,575.5 acres; and 3 in the Nances Creek Valley district, covering 988.5 acres. Drilling was done on the properties of 9 land¬owners in the Rock Run district, and on the property of 1 landowner each in the Goshen Valley and the Nances Creek districts. Drilling began October 26, 1942, and ceased on May 17, 1943.Power drilling was supplemented by a labor crew that drilled hand-auger holes in shallow deposits and sampled .old shafts, mines, and mine dumps.In all, 222 holes for a total of 13,250 feet were drilled. Of these holes, 88 penetrated bauxite but too low in grade to constitute ore."

Mar 1, 1948

Jan 1, 1968

By Paulo F. T. Sachs

ERP systems have been widely implemented nowadays in several industries. However, ERP was originally designed to fit former MRP and MRP II users, and most of the ERP research has been focused on discrete manufacturing . On the other hand, process industries ? and mining in particular ? present many peculiar characteristics, which are difficult to comply with ERP systems standard functionalities. Again, very limited research has been developed covering enterprise management systems in mining. The objective of this paper is to identify, through an explanatory study that includes a case study methodology, how ERP systems manage the functional areas of the mining industry, and how they fit into the mineral value chain IT requirements. A secondary objective is to identify the gaps between ERP?s functional capabilities and the mining industry business requirements, and to point out the perceived benefits they generate to the companies.

May 1, 2004

Silver is one of the three major metals produced from the Broken Hill mines. The accurate determination of the silver in these ores, therefore, is of economic importance.With due appreciation of the divergence of opinion of many who are interested in the subject of the determination of silver, the writer has been prompted to present the results of some recent experiments on silver losses during cupellation and conclusions from these experiments in the present paper. The losses of silver in the fire assay for this metal are due to silver retained in the slag during the fusion or scorification of the ore, and to silver volatilized from, and absorbed by the cupel during the process of cupellation.The literature describing the results of experimental work on silver losses due to the above causes is extensive, and the general conclusion of these experiments is that the silver lost in the slag is small, but that lost by cupellation is larger and more variable.The term cupellation loss in this paper refers to the total cupellation loss, no distinction being made between the absorption and volatilization losses.Volatilization loss is shown by King to be 0.5% of the total cupellation loss and, as it is generally accepted among assayers as being only a small fraction of the cupellation loss (3) (5), it will not receive further consideration in this paper.The factors causing the loss of silver by cupellation and the precautions to be obs~rved to reduce the loss in this operation are described in (1), (2), (3), (4) and (5). The...

Jan 1, 1940

By D. A. Ainsworth

"The first known use of activated carbon dates back to the Ancient Egyptians who utilized its adsorbent properties for purifying oils and medicinal purposes. Centuries later, the early ocean going vessels stored drinking water in wooden barrels, the inside of which had been charred. (However, by modern definition the carbon used in these applications could not truly be described as activated.) By the early 19th century, both wood and bone charcoal was in large scale use for the decolorization and purification of cane sugar.However, it was not until the beginning of the First World War that the potential of activated carbon was really capitalized upon. The advent of gas warfare necessitated the development of suitable respiratory devices for personnel protection. Granular activated carbon was used to this end as, indeed, it still is today.By the late 1930's there was considerable industrial scale use of carbon for both gaseous and liquid phase application and new manufacturing processes had been developed to satisfy the needs of industry. During the 1939-1945 war, a further significant development took place - the production of more sophisticated chemically impregnated carbon for the removal of both war and nerve gases."

Jan 1, 1984

By W. H. Schiffbauer

NIOSH has developed an active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) for warning workers as they approach known dangerous areas around heavy mining equipment and other dangerous work zones. HASARD is composed of a transmitter and a receiver. The transmitter generates a 60-kHz magnetic field using one or more wire loop antennas. Each antenna is adjusted to establish a magnetic field pattern for each hazardous area. The receiver, worn by the worker, is a magnetic field strength meter. The received signal is compared against preset levels which are calibrated to identify levels of danger. The receiver outputs can include visual, audible, and vibratory indicators and it can also be made to disable machine functions. HASARD was field tested on a Joy 12 continuous miner, a Komatsu 210 M Haulpak, and on a highwall launch vehicle. Slight modifications were made for each application. HASARD provided warnings as designed and proved to be rugged enough to withstand the harshest of production environments.

Jan 1, 2001

By S Hapugoda, J R. Manuel, M J. Peterson

Microindentation testing using the square–pyramid–shaped Vickers indenter is a well-established technique to determine the microhardness of minerals and materials. However there is a paucity of published microhardness data from Fe ore samples. It is acknowledged that an iron ore’s particle mineralogy and texture is critical to its processing properties, and it is therefore considered that the microhardness of different mineralogical/textural types may also relate to these properties. Mineral microhardness potentially provides inputs to the modelling of breakage characteristics during comminution, as well as the relationship between mineral chemistry and microhardness, and mineral microporosity and microhardness. Microhardness can be determined as single crystal microhardness, for more coarsely microcrystalline samples, or as ‘aggregate microhardness’ for cryptocrystalline or finely microcrystalline samples.Variations in the texture and mineral chemistry of common Fe ore minerals (eg martite and microplaty hematite, ochreous and vitreous goethite etc) are well established and this study provides microhardness data on different textural forms of Fe (oxyhydr)oxides from a variety of different Fe ore deposits. The data indicated that in general, the mineral grain size, microporosity and texture were the main influences on Fe (oxyhydr)oxide microhardness. There were no apparent systematic variations between microhardness and minor element mineral chemistry, with the possible exception of Al content in goethite (for goethites with Al content >0.5 wt per cent), and for goethite total element contents >90 wt per cent (determined by electron probe microanalysis, EPMA). Higher Al concentrations and lower total element concentrations in goethite EPMA analyses correlated with lower goethite microhardness. Microporosity and grain size were more important than texture to hematite microhardness. Different textural forms of dense hematite (eg martite, recrystallised interlocking hematite and specular hematite) with similar grain size exhibited comparable microhardness. Microhardness values for hematite and hydrohematite with little or no evident microporosity were also similar, whereas more porous forms of martite, microplaty hematite or hydrohematite exhibited lower microhardness.CITATION:Peterson, M J, Manuel, J R and Hapugoda, S, 2017. Microhardness testing of hematite-goethite Fe ores – implications for their textural characterisation and geometallurgy, in Proceedings Iron Ore 2017, pp 319–330 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 24, 2017

By Paul R. Clark

Outline ? Coal As An Energy Resource ? Canadian Clean Power Coalition ? Phase I of the CCPC Project ? CO2 capture options ? Gasification ? CO2 use ? Results ? Phase II Plans ? Next Steps TransAlta - Profile ? 9,726 megawatts (MW) of capacity ? 46,877 gigawatt hours (GWh) produced at an average plant availability of 88.4% ? 47 facilities in four geographies: Canada; the U.S.; Mexico; and Australia ? Fuel mix of coal (62%), gas (26%), hydro and renewables (12%) ? 23.2 million tonnes of coal mined ? 47.0 million gigajoules (GJ) of gas consumed

May 1, 2004

By Mary F. Koehler

Continuing a program of thermochemical investigation of compounds of to ferroalloy elements, this paper contains ins values of the heats of formation of two sodium molybdates (Na2Mo04 and Na2Mo207) and three sodium tungstates (NO2W4, Na2W207, and NA2W207, and Na2W4013). The experimental method was solution calorimetry. The solution medium was sodium hydroxide solution, except that hydrofluoric acid solution was used for sodium tetratungstate. The heat of formation values are given with reference both to the constit¬uent elements and to the constituent oxides. These data are of prime impor¬tance in the thermodynamic consideration of these substances, as their accumulation includes the most difficult and time-consuming steps toward evaluating the free energies of formation and thus the potential reactivities and thermal stabilities. Except for values for sodium monomolybdate and monotungstate, no previous similar data were contained in literature sources.

Jan 1, 1962

By Robert Stefanko

The growing demand for energy during the post World War I and World War II periods has prompted underground coal production to increase rapidly. This has been met primarily by mine mechanization, resulting in the development and application of new mining machine types. Correspondingly, the total connected horsepower of each machine as well as the number employed has enlarged rapidly since 1950. (2,3,9,14,16,17) Electrical consumption for each mine has also grown. In the early years of mining electrical applications, only d-c power was utilized underground. Yet, d-c machine limitations were soon realized, and many a-c systems were substituted to permit economic and efficient utilization of a-c distribution and motors. Due to the attractive torque characteristics, ease of distribution and speed control, several traction applications have continued to be powered by d-c motors. The result has been the now prevalent use of mixed a-c/d-c mine power. However, augmented electrical power employment seems to have added to underground coal mining electrical accidents.

Jan 1, 1974