Search Documents

Flow Sheet Simulation of Municipal Waste Treatment Processes

Sep 13, 2010

By Wendy L. Mathieson

The Bonneville Power Administration (BPA) will build about 500 miles of new 500-kV transmission lines in the next 5 years. Many new lattice towers will be built in remote locations or in environmentally sensitive areas. Therefore, micropile foundations were designed that could be installed in remote areas, in variable subsurface conditions, and in a manner that would reduce excavation volumes and potential erosion concerns. Typical lattice tower foundation axial loads range between 75 and 1,500 kips (300 to 6,700 kilonewtons [kN]) per leg, with uplift loads being slightly less than compressive loads. Lateral loads range from 5 to 320 kips (20 to 1,400 kN) per leg. Full-scale axial and lateral load tests were conducted in geologically representative soil units during the micropile design for the 9-mile-long (14-kilometer [km]), Kangley-Echo Lake transmission line that extends through a protected watershed east of Seattle, Washington. Micropile foundations for single and double circuit suspension and dead end towers were designed using these load test data.

Jan 1, 2004

By A. W. Bester

Paper written on project work carried out in partial fulfilment of B. Eng. (Mining Eng.) Cullinan Diamond Mine currently handles 3.2 million tons of run of ore per annum. This is done by means of an underground train system, which is located at 763 metre level. Four trains, one in each quarter of the pipe, collect ore from passes and transport it to centrally located tips in the north and south of the pipe. The ore is then split into coarse and fine fractions. The coarse fraction proceeds to the primary crushers in the north and south. Historically, mining has been performed in such a manner that an equal amount of ore has reported to each quarter of the pipe. However, the tonnage profile of the mine will change such that the ore will no longer be split equally. For approximately five years the majority of ore will report to the east and thereafter most of the ore will report to the western portion of the mine. This will continue for the remainder of the current infrastructure level?s operational life. Coupled with this is the fact that the mine is aiming to increase its annual production to 3.8 million tons. The result is that the current ground handling system cannot accommodate the additional tons and therefore alternative ground handling options have been investigated. The continued existence of Cullinan Diamond Mine relies on finding a system that can economically handle the additional tonnage. Three options were investigated. Firstly, a train option, which would be an upgrade of the current system, was investigated. Two truck options were also investigated, the first of which was a conventional truck option. The second truck option was more interesting and involved an unfamiliar Combi truck system. The truck options were investigated primarily due to the fact that the block height of the BA West (a new production block) can be increased by 15 meters if a truck option is decided upon. This would create a significant increase in revenue for the BA West project. Each of the options was assessed in terms of its physical and financial feasibility. In terms of the physical constraints, it was found that all three systems could work. Detailed financial analysis indicated that either of the two truck options would be a suitable solution. However, due to the limited information regarding the Combi truck option, it should be further investigated. This applies particularly to the actual running and maintenance costs for the equipment.

Jan 1, 2005

By Vladimir Admek, Paul W. Jeran, Michael A. Trevits

It has' been found that lithological conditions over the Pittsburgh Coal bed cause the subsidence coefficient to vary within the area of the subsidence trough. This precludes the use of European developed predictive models, which are based upon a constant subsidence coefficient. Regression analysis of the distribution of subsidence coefficients from 11 Bureau of Mines, U.S. Department of the Interior, longwall panel studies on the location relative to the edge of the panel has yielded a third degree polynomial equation. This equation has been incorporated into a BASIC computer program for use on a personal computer that allows users with no previous knowledge of the theory of subsidence to predict vertical movements over typical longwall panels in the Northern Appa1achian Coal Basin.

Jan 1, 1986

Virtual Reality (VR) simulations are excellent tools for training, education, simulation of abnormal and dangerous conditions in mines and solving complex problems. Although the concept of VR has been around for nearly half a century, it has taken recent advances in hardware and software to bring this technology to within the budgetary reach of ordinary users and researchers. VR is now successfully being used in the minerals industry for: data visualization, accident reconstructions, simulation applications, risk analysis, hazard awareness and training. The Institute of Sustainable Minerals Industry, Advanced Computer Graphics and Virtual Reality Research Group (SMI-VR) at the University of Queensland, established in late 2000, has been involved in developing VR applications for the minerals industry in conjunction with various research centres. This paper illustrates the benefits of using advanced computer graphics and VR techniques in the minerals industry with some examples of applications developed.

Jan 1, 2003

Ferrochrome is the major chromium source for stainless steel production, and submerged-arc furnaces (SAF) are most commonly utilised to smelt chromite ores into ferrochrome by using suitable carbonaceous reductants such as coke. Because of the complexity of feed structure and electrical-thermal-chemical interactions, there exist large gradients and wide distributions of temperature, mineralogy and other process variables in the furnace. This leads to various zones in the furnace, and different reduction mechanisms. Control of the furnace is thus often difficult due to the complicated physical and chemical situations in the furnace. The temperature profile in the submerged arc furnace has a great influence on the reduction rate and the production efficiency. Therefore, the energy generation through electrical arcs submerged in the solid feed and its distribution within the packed bed play an important role. In the present paper, an overall process model is illustrated to simulate inter-linked transport processes of fluid flow, heat transfer and reduction kinetics within the submerged arc furnace. The application of reaction kinetic data to simulate the chromite pellet/lumpy ore reduction with CO gas is presented and further adjusted to provide a submodel for a flow and heat transfer simulation for the packed bed by using computational fluid dynamics (CFD) technique. The comprehensive process model is aimed to simulate materials and gas flow, temperature and energy distribution throughout the furnace system. A preliminary model for gas flow and temperature distribution for the upper part of a 20 MW furnace (the packed bed) for high carbon ferrochrome production has been developed under simplified conditions. The integration of the reaction kinetic model into process simulation, and the future vision for a more comprehensive process modelling are discussed. It is expected that better understanding of the furnace insights through process modelling will help process optimisation and furnace control.

Jan 1, 2004

By Leon Maday, Robert Robinson, Judy Cochran, Don Davis

Over the past 20 years, several soft-ground tunnels have been successfully completed in the Seattle area. These tunnels were built using design-bid-build contracting methods, and have benefited from advancing technologies in exploration, design and construction methods. Owners have utilized various contractual means to share some of the risks that are inherent to tunneling projects. This has helped to foster a competitive bidding environment and to resolve issues related to unanticipated underground conditions in a fair manner. This paper presents case histories of tunnels constructed by King County and the Washington Dept. of Transportation that illustrate a common approach to design and construction issues. The common thread is successful project completion with minor cost changes under the design-bid-build contracting method. Lessons learned from these projects are being applied to the upcoming King County Brightwater Project tunnels, Sound Transit’s Light “Link” Rail tunnels and other tunnel projects.

Jan 1, 2005

Analysis of rock discontinuities, collected using a scanline method, has been undertaken at the Iron Duke open cut mine, on the southern margin of the Middleback Range in the Gawler Craton, South Australia. The iron mineralisation, which is a product of supergene enrichment of carbonate sediments, is located on the W (western) limb of a gently N plunging D2 macrosyncline. Mesofolds plunge shallowly to the NE or steeply to SE, suggesting two shortening events, of which the second produced significant macrofolds. Discontinuities include:faults and shears which display variable orientations, mainly striking WNW dipping steeply N; mesofractures or joints maintaining a well constrained orientation, dipping steeply S, subvertical striking E-W; and bedding surfaces which are folded about a gently N plunging axis. Through this example of the regional control exerted on local discontinuities, it is clear that discontinuities are not randomly distributed as often assumed in purely statistical approaches. Commonly for rocks of any age there is a distinct discontinuity pattern, reflecting the geological deformation history. If the controls exerted on local rock discontinuities can be determined and assigned a number related to their significance, the way forward is available to develop a site specifc knowledge base that can make realistic predictions for any position in a given rock mass. Such a procedure would involve assessment of the regional geology, linked to scanned discontinuities either via manual or automatic means. Recent advances in automatic scanning rock faces (eg by the I-SiTE Laser Radar) to determine discontinuities distributions, enable the rapid calculation of rock characteristics. This is a significant advance in rock engineering, providing a method of safe and quick collection of data. However it creates problems in the presence of an increase in the geotechnical data available, which should be assessed in the context of the regional geology. Although techniques are underway to analyse post-blast discontinuities, the next signifant potential advance in this area could be the integration of a knowledge based system to assess discontinuities ahead of mining, incorporating regional assessment and human intuition.

Jan 1, 2000

By Derek Ellis

Volume II of this two-part series on Submarine Tailings Disposal (STD) as a tailings management option for coastal and island mines contains descriptions of lesser known case histories. The Misima gold mine (Papua New Guinea) and the Black Angel lead-zinc mine (Greenland) are described in some detail as the best documented cases. Atlas copper mine (The Philippines) is less fully described due to relative lack of documentation. The Misima and Atlas STD systems are working to their design criteria. At Black Angel the system adopted did not prevent contamination for a number of reasons, which are now understood. Two cases are described where STD is being developed. They are the Cayeli Bakir copper mine Turkey), and the Toquepala and Cuajone mines (Peru). There is excellent documentation available for both cases. Three case histories are described where tailings have reached the sea either through beach or river discharge. In one case the STD option has been explored (Marcopper Mine, The Philippines). In the others we explore in hindsight whether STD might have been a viable alternative using the Screening Criteria that this Volume develops - see below. The mines are Bougainville Copper Mine in Papua New Guinea, and Jordan River Mine (Canada). There is potential for STD at all three sites. Finally, the Volume presents Screening Criteria for appraising STD, based on the experience in design, operation and environmental impact reviewed in the case histories.

Jan 1, 1994

By Bernard J. Steblay

The U.S. Bureau of Mines has attempted to use ultrasonic signal travel-time measurements to measure loaded roof bolt strains. The strain measurements are then related to roof bolt loads through equations or empirical calibrations. Such techniques offer the potential of accurate, rapid bolt load measurement that does not disturb the anchotage. This report presents 6e research findings for a specific type of ultrasonic measurement instrument using a pulsed-phase-Iock-Ioop technique. This technique measures signal travel time indirectly by measuring frequency changes. A complete development of the applicable theory and detailed derivations of key equations is presented along with empirical laboratory and field results. The differences between anticipated and measured behaviors are analyzed and discussed. The report identifies problems encountered in applying pulsed-phase-Iock-Ioop technology to roof bolt load measurement and provides potential solutions to many of them. A key assumption of pulsed-phase-lock-loop theory is that driving and reflected signal frequencies will always be equal. Findings showed that not only were actual frequencies not equal but they were not stable or simply related. Reflection wave shape also was not stable. The ramification of these findings and ways to minimize their adverse effects are presented.

Jan 1, 1990

By W. A. Dunkley, W. W. Odell

About two-thirds of the manufactured gas supplied to the public by the gas plants in the Illinois district is cnrbureted water gas. The leading generator fuel is coke, ma.de in by-product c.oke ovens or in retorts, chiefly from eastern gas coals. During the fall and winter of 1917-18, when the demand for coke by war industries and the restrictions of the Fuel Administration in connection with the transportation of coke from eastern States made it almost impossible for many gas companies to obtain their coke requireml'nts, several water-gas plants had to use bituminous coal as generator fud. Many operating difficulties were encountered, some of which were solved more or less satisfactorily in different plants. A number of plants attacked the problem rather blindly because facilities for making tests were lacking and because technical men were too busy with labor and supply problems to study thoroughly the conditions involved or to ascertain what other plants had done with this fuel. It was therefore with the hope of assisting the gas industry during this critical period, and of promoting the use of Central District coals for gas making, that the Illinois Mining Investigations, a joint agency of the U. S. Bureau of Mines, the University of Illinois, and the Illinois Geological Survey Division undertook the, tests discussed in this paper. • This report was compiled under the auspices of a technical committee appointed by Gov. Frank 0. Lowden to promote the use of Central District coals in gas manufacture as a war measure. This committee included the following representatives of the various agencies concerned: U. S. Bureau of Mines, E. A. Holbrook and W. W. Odell; Illinois Gas Association, C. W. Bradley and R. B. Harper; University of Illinois, Dean C. R. Richards, Prof. S. W. Parr, and Prof. H. H. Stoek; State Geological Survey Division, F. W. De Wolf, G. H. Cady, a.nd W. A. Dunkley. F. W. De Wolf was chairxnan of the committee and E. A. Holbrook was secretary.

Jan 1, 1924

Two new inorganic-organic hybrid polymers, Al(OH)3-polyacrylamide (Al(OH)3-PAM) and Mg(OH)2-polyacrylamide (Mg(OH)2-PAM) were synthesized and successfully applied for the treatment of oil sand tailings. The results indicate that both Mg(OH)2-PAM and Al(OH)3-PAM were unaffected by the change in pH, and could be applied to oil sand tailings with varying sand-to-fine ratio (SFR). The optimum dosages for the Mg(OH)2-PAM and Al(OH)3-PAM were about 330 g/ton and 650 g/ton, respectively for SFR 3.75. The flocculated oil sand tailings dewater quickly producing 66-68% solids. The flocculated tailings produced similar filtration rate before and after shear. Mg(OH)2-PAM treated oil sand tailings produced twice the filtration rates (220 ml/min) compared with Al(OH)3-PAM. This study clearly indicates that Mg(OH)2-PAM and Al(OH)3-PAM is a viable solution while decreasing the mass-production of tailings and increasing the rate of water-recycle.

Jan 1, 2012

By William H. Pomroy

The Bureau of Mines, through a 4-year program of combined in-house and contract research, has developed the necessary hardware and software technology to provide rugged, reliable automatic fire protection for surface mining mobile equipment. One element of this program was a continuing effort to help foster rapid mining industry acceptance of the technology by keeping end user costs reasonable. This report is an analysis of the economic impact of surface mining mobile equipment fires and the cost benefit of utilizing automatic fire protection systems to abate these losses.

Jan 1, 1982

By T. C. Eisele

The use of column flotation was considered for the ?reverse flotation? of iron ore, where the gangue (quartz) was recovered in the froth product. This use of the froth for carrying the gangue mineral rather than carrying the valuable concentrate significantly changes the operational requirements of the column. The objective of this work was to determine which of several column flotation technologies would be most suitable for this type of flotation operation. Studies were carried out using both the Jameson column and the Deister column. Comparative results are presented that show the capabilities of both column types in this application relative to conventional Wemco flotation cells. Columns were demonstrated to have grade-recovery performance superior to what could be achieved with conventional cells. Two-stage flotation with the columns could produce a concentrate that was up to 70.2% Fe at 87.5% iron recovery, compared to 70.4% Fe at only 77.7% iron recovery for four stages of flotation in conventional cells. It was shown to be particularly important to operate the columns to recover a maximum of the quartz gangue into the froth. It was noted that there are often problems in scale-up of laboratory columns to plant scale, because the increase in height and the decrease in the ratio of height to diameter at the larger scale allows more axial mixing and bubble coalescence, both of which degrade the column performance. Horizontal baffling was shown to improve column performance by reducing axial mixing and breaking up large bubbles, and so the use of such baffles in the reverse flotation application was investigated.

Jan 1, 2007

By M. M. Tilman

In a Bureau of Mines investigation to develop lead alloys with improved tensile strength and creep resistance, lead-base alloys containing cadmium and antimony in nominal 1-to-1 atomic ratios were melted in air, cast, and rolled into sheet to 90 percent reduction at temperatures varying from room temperature to 175° C. Tensile testing at room temperature and stress-rupture testing at 900±3° F were conducted on the as-rolled alloys. The best tensile properties were observed in an alloy of Pb-4.2 wt pct Cd-4.5 wt pct Sb which exhibited an average tensile strength of 7,270 psi with 36 percent elongation in 2 inches. An alloy of Pb-5.5 wt pct Cd-6.0 wt pct Sb had 100-hour stress-rupture values of approximately 2,100 psi and 1,000-hour values of approximately 1,700 psi.

Jan 1, 1969

By Alvin Kaufman

To aid industry and Government in planning water developments the Bureau of Mines in 1963 canvassed mineral producers to determine water use in 1962. Water use by the mineral industry comprises only 2 percent of the water withdrawn by industry as a whole. The major water-using mineral industries are natural gas processing, phosphate rock, sand and gravel, and iron ore. Analysis indicated the following conclusions: 1. Total water use and new water intake is dependent on the quantity of material processed and the process water requirements of the particular industry or commodity. 2. Recirculation is dependent on the processing requirements of a particular commodity, the manner in which the water is used, cooling and condensing requirements in certain large industries, the quality of new water intake, and the need to treat new and discharged water. 3. Consumed water is dependent on the quantity of water recirculated, the temperature and humidity in the area, and the proportion of water used for cooling and condensing. 4. A threefold increase in water use by the mineral industry by 1985 is forecast

Jan 1, 1966

By H. K. Lin

Cyclic voltammetric and potential step chronoam-perometric techniques were used to study gold dissolution in cyanide solution. Three distinct anodic and one cathodic peaks appear on the voltammogram between -0.50 and 0.80 V vs SCE. The corresponding reactions were proposed to explain the peaks and the passivations. The proposed reactions were in agreement with the effect of pH, cyanide concentration and the rotating speed of the electrode on the magnitude of the peak currents. Cyclic voltammetric tests, with various vertex potentials, were also conducted to examine the proposed reactions. Steady-state currents at various potentials were obtained by potential step chronoamperometric technique and were compared with transient currents obtained by the cyclic voltammetric technique.

Jan 1, 2000

By Paul M. Buttermore

As part of a national canvass of water use the Bureau of Mines compiled data on water requirements in the petroleum and natural gas industries for the calendar year 1962, specifically in well drilling, secondary-recovery operations, and natural gas processing plants. Total new water use in the petroleum industry of the United States, excluding refining, was 5.3 billion barrels. Secondary-recovery operations and natural gas processing plants required about 2.5 billion barrels of new water input; each of these requirements was about eight times greater than that for well drilling. Total use, including recirculated water, was 45.3 billion barrels of which 3.4 billion barrels was consumed. The greatest use of recirculated water was for natural gas processing, amounting to 38.2 billion barrels. Projections of total water use show that by 1975, 75.4 billion barrels will be used by the petroleum industry, of which 10.2 billion barrels will be new water. By 1985, the total use requirement will be 92.8 billion barrels, of which 13.1 billion barrels will be new water.

Jan 1, 1966

By Paul M. Buttermore

As part of a national canvass of water use the Bureau of Mines compiled data on water requirements in the petroleum and natural gas industries for the calendar year 1962, specifically in well drilling, secondary-recovery operations, and natural gas processing plants. Total new water use in the petroleum industry of the United States, excluding refining, was 5.3 billion barrels. Secondary-recovery operations and natural gas processing plants required about 2.5 billion barrels of new water input; each of these requirements was about eight times greater than that for well drilling. Total use, including recirculated water, was 45.3 billion barrels of which 3.4 billion barrels was consumed. The greatest use of recirculated water was for natural gas processing, amounting to 38.2 billion barrels. Projections of total water use show that by 1975, 75.4 billion barrels will be used by the petroleum industry, of which 10.2 billion barrels will be new water. By 1985, the total use requirement will be 92.8 billion barrels, of which 13.1 billion barrels will be new water.

Jan 1, 1966

By P. Fredriksson, S. Seetharaman

In the ladle refining process, the ?FeO?-content of the ladle slag is of great importance in the chemistry as well as the energetics of the process. An optimization of the process requires an accurate knowledge of the thermodynamic activities of ?FeO? in the ladle slags. Due to the discrepancies in the existing data, renewed attempts are being made at the Royal Institute of Technology to generate reliable data for binary, ternary and multi component slags containing ?FeO? at steelmaking temperatures. In order to measure the activities of ?FeO? in the slags, a gas equilibration technique was employed in the present work. The slags, kept in Pt-crucibles, were equilibrated with a CO-CO2-Ar gas mixture and quenched after equilibration. The chemical composition of the slag was analyszed. From a knowledge of the thermodynamics of Fe-Pt system, the ?FeO? activities in the slag could be evaluated. The results of the present studies, together with other literature values, were optimized in the slag software, THERMOSLAG® developed in the Royal Institute of Technology, Sweden. The results of the optimization are presented. Model calculations were performed with the KTH slag software, THERMOSLAG®, by using plant data from OVAKO Steel, Hofors, Sweden. It was found that oxygen estimations in the metal from the ?FeO? analyses of slags, obtained by conventional sampling and analysis methods, where less reliable. Estimation of the oxygen levels utilizing the sulphur partition between the slag and the metal were carried out using the THERMOSLAG® software. Reasonable estimations of the oxygen contents in the metal confirmed that this could be a very useful tool for the plant operator. Keywords: ladle, thermodynamics, slags, ?FeO?, experimentation, modelling, sulphur partition

Jan 1, 2004