Search Documents

By Michael Allen, Paul Worsey

In underground blasting, the pull of the initial cut is the limiting factor for the success of the rest of the round. By improving the pull of the first cut, a critical step is made towards improving the entire round. This project attempted to optimize a burn cut’s effective pull by varying the depths of the relief holes in the burn. The effect of varying the depths of the relief holes was investigated, including depths longer than that of the cut’s charged holes. The overall objective was to consistently achieve greater pull than in a standard burn, using an identical amount of explosives. Increased pull results in savings of both time and cost in underground heading advance.

Jan 1, 2015

By J. D. Bliss

The discovery that triggered the current gold rush in southeastern Peru was made in about 1975 along the Rio Madre de Dios in Madre de Dios Department (Fig. 1). About 5000 to 10,000 miners (called chichiqueros) were working in the area as of 1990. Placer mining is the principal source of revenue for people living along the Rio Inambari and west of Puerto Maldonado. As in past gold rushes, working and living condition are harsh. Supplies are expensive, and the area has poor access compared with other areas in Peru. Food, fuel and all mining supplies are trucked over dirt roads from Cuzco, a three-to-five-day trip (Fig. 1). Some material also comes from Brazil. Many placers have a similar life cycle, beginning with small-volume mining (surface or underground). At the end of this small-scale mining, the placer is exhausted or it has a sufficient volume of gravel high enough in gold grade to be worked by large-volume methods, which lead to exhaustion of the resource. The level of maturity of a placer can be determined from its gold grade. The amount of gold production from large-volume mining can be predicted, given detailed, cumulative gold-production data on placer deposits during small-scale mining (Bliss et al., 1987). Using this general model, the authors analyzed the placers in the Rio Madre de Dios area. Small-volume mining Most placer mining in the Rio Madre de Dios area is in alluvial deposits either in or bordering the major rivers. Locally, some placer mining is in terrace deposits above the rivers. All minerals (including the subsoil) in Peru belong to the state. However, a mining claim (denuncia) is easily obtained for mineral exploitation. It is separate from property ownership.

Jan 1, 1992

By Michel Ruel

"This paper describes how to make advanced control choices when difficult processes need improvement. The decision-making process involves choosing between a rules-based approach and a model-based approach as well as weighing benefits and drawbacks, complexity and simplicity, investment and results. This paper will present briefly each solution: basic control, advanced regulatory control, model predictive control, and expert systems such as fuzzy logic controllers and neural networks. The article then proposes a decision tree for selecting the most appropriate approach. A table will compare usage, development, commissioning, maintenance and lifecycle costs for each approach. Finally, conclusions and suggestions will summarize the methodology.INTRODUCTION Advanced process control (APC) is a popular topic. How can one decide whether advanced control should be added to an existing system? Advanced control is used to improve performance, stabilize production, handle constraints, protect equipment and manage grade changes. Most plants use feedback controllers, usually PID (proportional, integral, derivative) controllers. It is common to develop special control schemes to handle more complex processes. In classic PID process control, a controller brings a single value close to a set point using a single manipulated variable. On the other hand, APC brings several values close to optimal targets simultaneously using several manipulated variables. APC's four main strategies are advanced regulatory control, model predictive control (MPC), fuzzy logic and neural networks. Simple solutions are always preferred. Complexity will be increased if performances (production, quality, etc.) are below par. Profitability analyses should be conducted to validate project viability. Needs—not trends—should dictate choices! Before increasing complexity, it is important to define needs, goals, technical support, budget, etc. All these approaches entail strengths and weaknesses. Building a project based on technology rather than needs spells trouble."

Jan 1, 2014

A single compartment 100 A electrolytic cell charged with AICla-KCl-NaCl at 750°C was studied during an experimental campaign of 4 months. About 10 1b of aluminium were produced in continuous runs which lasted up to 1 week. The highest cathode current efficiency determined was 80 per cent. Anode current efficiency. cathode potential, analyses of melt, sublimate, and product, and reactivity of cell materials were also recorded and interpreted in terms of the role of lower valent aluminium species in the electrolysis mechanism.

Jan 1, 1971

The published liquidus data on the Pb-PbS system have been correlated on the basis of one-coefficient Margules equations. Thermodynamic properties of the components of this system have been obtained, and it has also been found that the calculated miscibility gap of this system exists over a very narrow range of temperature (1041 to 1058°C).

Jan 1, 1972

By Eraldo Florêncio, Paulo Couceiro, Manuel Lopez Cano

Specialized marine blasting techniques were required to deepen and widen the access channel and turning basin of the Sudeste Port Terminal in Rio de Janeiro, Brazil. This terminal has been designed to handle the exports of iron ore and other bulk solid cargoes to international markets. The Sudeste Port Terminal is connected to the iron ore quadrangle in Minas Gerais State by a dedicated railway line, giving Brazil’s independent miners a seamless access to global markets. However, the Sudeste Port Project is located in a protected marine environment. Blasting in this area has required a comprehensive blast induced ground vibrations monitoring and analysis program to ensure the safety of the sensitive structures surrounding of the blast areas. Nevertheless, the risk of generating higher ground vibrations on nearby structures due to the combination of short distances, larger excavations layers and complex geology, increased the complexity of the blast due to the limitations imposed by the maximum instantaneous charge and a demanding project schedule. Site-specific test blast programs were planned and executed in order to obtain in-situ vibration data to establish the local attenuation law, and also to better understand the role of dominant frequencies before production blasting started. This paper summarizes the main findings and solutions applied during the marine blasting project in the Sudeste Port Project.

Jan 1, 2018

By Carroll Forbes

INTRODUCTION MANY different shapes of drill bits are in use with hammer drills, but little definite information is available whereby to judge which one of these shapes is the best. The following investigation was undertaken in order to determine what effect, if any, the shape of the cutting edge has on the cutting speed and wearing qualities of drill bits. The bits tested were those in common use, namely, the 4-point or cross bit, the 6-point bit, the Z bit and the "Carr" bit. The rock in which the tests were made was the red granite from southeast Missouri. It is a coarse crystalline granite containing an unusually large amount of quartz and is extremely hard, and on account of its uniform texture is admirably adapted to this work. While tests in other rocks might show somewhat different results, nevertheless it is the opinion of the authors that the relative cutting quality inherent in the shape of the bits would be the same in all rocks. Other qualities, such as mudding freely, freedom from fitchering, etc., might make one bit more desirable than another in softer rocks. DESCRIPTION OF BITS TESTED The 4-point bits were the usual shaped bits commonly made on the Leyner sharpener with 14° taper on the wings and a 90° angle between cutting edges. Some tests were run at 85 lb. pressure with a 4-point bit made with a 5° taper on the wings. This was made by using the Carr bit die. The 6-point bits were the usual shaped hits made on, the Leyner sharpener. The Carr bits were made with a 5° taper and an angle of 100° between cutting edges.

Jan 8, 1917

By R. E. Simpson

Beginning in 1972, fully grouted resin bolts were used in underground mines. An estimated 20 million resin bolts will be installed in 1980 owing to their apparent support improvement in most roof-bolt applications. Inorganic cements were tested to replace the resin at a lower cost while retaining the advantages of a grouted bolt. Although other inorganic materials were considered, all but portland and gypsum cements were rejected for reasons of availability, performance, or cost. Portland and gypsum-type cements were tested by the Bureau of Mines to select a fast-hardening, low-cost material that would anchor a roof bolt adequately to meet safety standards. An alpha-gypsum cement, accelerated with potassium sulfate, was selected as the best material because it had adequate pull strength at a desired set time of less than 5 minutes and was readily available.

Jan 1, 1980

By G R. Dickens, N H. S Oliver

Deformed regions of the Hamersley Province, Western Australia, contain several major iron ore deposits where banded iron-formation (BIF) of the Dales Gorge Member was converted to martite-microplaty hematite. The genesis of these ores remains controversial, in part because no study has systematically documented how stratigraphically equivalent rocks change chemically from undeformed regions into the deposits. Profound chemical and mineralogical differences do occur between rocks in the undeformed north and mineralised south. BIF and shale can be classified into three types: BIF, altered BIF and iron ore, and black shale, altered black shale and red shale. A series of low temperature (20 to 250¦C) chemical reactions can explain the observed differences in chemistry and mineralogy. The inferred reaction paths indicate that no single process could have produced all of the altered rocks at Mt Whaleback. Recently described carbonate-rich, silica-poor rocks at Mt Tom Price (Taylor et al, 2001) suggest this alteration sequence is even more complex. Our favoured explanation for the genesis of hematite ores is one that can explain deposits at Mt Whaleback and Mt Tom Price: following regional metamorphism, hydrothermal fluids locally formed carbonate-rich, silica-poor BIF with magnetite and carbonate-rich altered black shale. Subsequent surface derived fluids oxidised this magnetite, crystallised microplaty hematite (mpl) and eventually dissolved carbonates and silicates leaving high-grade ore. Either during or sometime after mineralisation, acidic, oxygenated fluids converted altered black shale to red shale and unaltered BIF to martite-rich BIF without carbonates across the southeast of the province.

Jan 1, 2002

Traditional fine grinding mills in mineral processing relied on the use of steel medium for particle size reduction. The successful development of the Isa Mill(a horizontal stirred mill with 3000 litres of net chamber volume and 1120 kW rated motor power)adopted a novel product separator design that has led to a major revision of medium use in fine grinding. The Isa Mill separator has also successfully operated with a wide variety of medium types such as silica sands, river gravel, smelter slag, run-of-mine ore fractions and steel shots, with size ranges from 0.5 to 10 mm. A great flexibility of the Isa Mill operations has been achieved for processing a feed as coarse as 120 um to a product as fine as 5 µm. This paper discusses the performance of two inert grinding media used in the Isa Mills in Mount Isa Mines of Australia for processing galena and sphalerite bearing ores to below 10 microns. They are the copper reverberatory furnace slag (CRFS)and the heavy medium plant rejects (HMPR). A methodology was also demonstrated for comparing the medium performance and for scaling up the Isa Mills from a 1.5-litre laboratory batch mill to a full scale 3000-litre mill.

Jan 1, 2000

By Gray Mullins

This paper presents experimental results from a study to assess the interface bond between a cast-in-place concrete seal slab and prestressed concrete piles in cofferdams. Three different seal slab placement conditions - fresh water, salt water and bentonite slurry - were evaluated and the results compared against controls where no fluid had to be displaced by the concrete. Normal pile surfaces were investigated. Additionally, the situation of ?soil caked? piles was also investigated. Both model and full-scale tests were conducted. In the model tests, twenty eight 15 cm square prestressed sections were used with the embedment depth varied between d-2d, where d is the width of the pile. In the full-scale tests, 16 specimens were tested. The prestressed piles were 36 cm square with the embedment varied between 0.5d-2d. Four of the sixteen piles were cast with embedded gages located at the top, middle and bottom of the interface region. The results showed that loads were transferred to the piles over an effective area, not the entire embedded depth. Significant bond stresses developed even for the worst placement condition. Recommendations are made for revising current values in specifications.

Jan 1, 2013

By Charles Deacon

The mining industry is constantly taking greater cognisance of their operating costs as a strategy to counter the effects of falling commodity prices. As a result, optimal operating efficiency is more important than ever. One such operation is that of blasting. Considering the relative increasing costs of explosives and accessories it is desirable to optimise the number of blast-holes fired by maximising their individual output. This achievement may now only be possible following the advent of higher technologies in the form of modified explosives and electronic detonators. This paper reviews and introduces some techniques of blast monitoring, types of operations where each is most suited, resulting modifications to blast designs, and identifies some pitfalls to watch out for when analysing the results.

Jan 1, 2000

By Nutter R. S.

A methodology has been developed for qualitative safety hazard evaluation and quantitative reliability analysis of mine monitoring and control systems. Detailed application of these techniques were made to two commercial monitor/control systems and to a West Virginia University distributed microprocessor-based system. A controlled environmental test was conducted on a set of one of the commercial system's outstations. A software reliability evaluation methodology was also developed and applied.

Jan 1, 1982

By Ronald T. Mayerle

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 20,500-acre part of the 104,085-acre Rincon Wilderness Study Area (OR-002-082) in order to evaluate its identified mineral resources. The wilderness study area is located in Harney County, OR, about 12 miles west from Fields. No mineral resources were identified within the study area. A literature search found no records of mining or minerals exploration, nor did a ground search find any evidence of mining-related activity. Of seven alluvial samples taken from the major drainages of the study area, all were barren except one. This sample, taken from a dry streambed along the southern boundary, contained $0.07 gold per cubic yard; however, this small amount of gold is of no economic significance, and the source is probably outside the study area. The Pueblo-Steens mining district extends to within 4 miles east of the study area. No evidence of geological environments similar to those that were responsible for the formation of resources or occurrences of metals and nonmetals within the district is known within the study area.

Jan 1, 1987

By Jack W. Carlson

Considering the magnitude of today's public concern with critical mineral and fuel materials, regarding both their midterm and long term availability, the Nation is fortunate to have in place and operating the coordinated data systems of the Geological Survey and the Bureau of Mines. Under the supervision and policy direction of the Assistant Secretary--Energy and Minerals, these Department of the Interior agencies have long been responsible for important mineral activities in the Federal Government. Aside from their highly respected mineral industry publications such as the monthly Mineral Industry Surveys, annual Commodity Data Summaries and topical Professional Papers and Reports of Investigation, the Bureau of Mines and Geological Survey data bases and expertise have been readily available for use in emergency situations. Policymakers and decisionmakers in government have placed major reliance upon this ready mineral data and analytical capability in World War II, the Korean War, the recent price control era, and the Arab oil embargo.

Jan 1, 1975

By T. A. Lloyd

"This paper indicates the extent to which Canadian coal mine operators have taken advantage of developments in the science and technology of coal that would allow them to better satisfy changing market demands through improving the properties of their products. At some mines, no attempt is made to alter the coal from its as-mined condition, but at most mines grading into various size ranges and hand-cleaning of lump sizes is undertaken.Over-all, Canada Jags behind most of the other major world coal producers in the proportion of its coals being processed in wash plants. To some extent, this is due to the fact that a high proportion of the coal production satisfies market demands without such treatment. On the other hand, a few of the coal mines in Canada, which produce about 25 per cent of the nation's total coal output, have in operation some of the most modern coal beneficiating equipment available, including jigs, flotation cells, water cyclones, centrifuges, disc filters and thermal dryers."

Jan 1, 1968

By G McMillan, P Mulvey

"Geochemical characterisation is done based upon the geology and metallurgical batch testing prior to commencement of the operation of the plant.  Tailings repository design is based upon geochemical assessment of the waste material, as well as the geomechanical issues associated with storing the waste. The resultant conceptual and detailed design is incorporated into the environmental impact statement (EIS), upon which mine approval is based. The entire environmental monitoring and harm mitigation program, which is usually a condition of the Mine Lease approval, is based upon the applicability of the original characterisation.Tacit to this process is that there is no change in the geochemistry of the tailings, i.e. no change in the implications for acid & metalliferous or saline/neutral mine drainage (AMD/SNMD) generation. But any changes in milling and processing can have a substantive impact on the geochemical behaviour of the tailings metallurgy, and potentially render an operation non-compliant within the conditions of the mine license.Environmental and statutory approval implications for continuous improvements of metallurgy need to be understood because unintended consequences could cost more than the benefits of the improvement, and in some cases cost more than all the profit made from the mine.  Examples uncovered during audit and consultant practice will be presented together with a process to ensure implications for adverse environmental harm and license conditions are fully considered.*This paper is only available for individual download. It is not included in the conference proceedings*CITATION:Mulvey, P, 2013. Continuous improvement - how changes in metallurgy can have a substantive impact on environmental impact and closure - lessons learnt from environmental auditing, presented to MetPlant 2013 Conference (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jul 15, 2013

This Bureau of Mines report comprises tables listing the name, location, and other pertinent data concerning certain future fuel-related projects. The tables include information on projects involving the proposed or planned development of fuel resources, as well as the development of storage, transportation, and conversion facilities; the report covers the 26 States east of the Mississippi River. Of the total 594 projects for which information is provided, 492 concern coal mines and electric generating plants.

Jan 1, 1976

By C. A. Komar

The Bureau of Mines conducted oil-displacement tests in the laboratory with three water-in-oil and five oil-in-water emulsions that were created with ultrasonic energy at a frequency of 20 kHz and an acoustic intensity of approximately 100 watts per cm2. Emulsions of either crude oil or kerosine, brine, and 112 to 2 percent emulsifier were formed during 30 seconds of acoustic irradiation. Results indicate that ultrasonic energy induces greater and more uniform dispersion of one liquid in another in the presence of small amounts of chemi¬cal emulsifiers. When the emulsions were injected as a buffer slug before waterflooding, recovery of the oil-in-place was 8 to 22 percent greater than with conventional waterflooding in the test specimens, regardless of the con¬tinuous phase (oil or brine). The emulsions do not appear to be applicable to the Appalachian area; however, because the oilfields are too "tight," the clays in the formation remove the emulsifier from the displacing fluid, and not enough additional oil is produced, compared with recovery using conventional waterflooding, to warrant the increased operating costs.

Jan 1, 1969

By Thomas Lardner

Excavation for The Bow, EnCana, in downtown Calgary, occurred between May 2007 and September 2008. A monitoring programme was used to determine the behaviour of the shoring wall, soil and bedrock during the excavation for the 21 metre (69 ft) deep excavation with a footprint of approximately 17,000 m2 (183,000 sq ft). Results from the inclinometer readings indicated that significant horizontal movement due to a weak rock layer and shear band effect. These modes of movement account for up to 100 mm (4.0 in) and 45 mm (1.8 in) of lateral deflection, respectively. Based upon the results of the monitoring programme, rock samples were collected from the weak mudstone bedrock, with great difficulty, to determine the strength and deformation parameters. Results from the uniaxial compression tests indicate a UCS around 830 kPa (120 psi) and elastic modulus between 80 and 180 MPa (11 and 26 ksi). Mohr-Columb parameters were determined to be c' = 340 kPa (49 psi) and f' = 24°. Residual strengths were determined to be c'r = 0 and f'r = 15°. Using the results of the laboratory tests and field investigation records, an initial finite element analysis was conducted. Results of the analysis show good correlation when compared with the observed monitoring deformation, indicating accurate portrayal of rock parameters. Additional analysis and investigation is required to determine the principal horizontal stresses in magnitude and direction.

Jan 1, 2010