Search Documents

By A. S. Argon, G. East

From their study of the anisotropy of grain boundary mobility in aluminum, the authors conclude that tilt boundaries have a higher mobility than twist boundaries because the atomic misfit at the pure-twist boundary is relatively small compared to the misfit at a tilt boundary for a given amount of misorientation. If this is true, then one would expect a twist boundary to have a lower grain boundary energy than the corresponding tilt boundary. Fig. 6, taken from the work of Gjostein and Rhines,10 shows that this is indeed the case for [001]-cu tilt and twist boundaries in the high-angle region, thus lending support to the authors' conclusion.

Jan 1, 1968

By Rocky (Yaokun) Wu

This paper introduces the development and application of a new cable anchor - Cable-Lok for pre-stressed cable bolting in mines. Cable-Lok is a spring-loaded cable anchor suitable for the drill hole diameter of 50 and 65 mm (2" and 2.5") in medium soft rock to hard rocks. The cable anchor is automatically set on installation and the cable can be tensioned immediately to provide active and primary support throughout its length. Post-grouting can be conducted independently. In comparison with the conventional cable bolting, Cable-Lok anchor will greatly speed-up the cable bolting circle and decreases the cost of cable bolting. Cable bolting anchored with Cable-Lok anchor has wide application in mines, e.g. pre-stressed cable bolting in large span drifts and intersections for permanent rock support, or in hanging walls or stopes for temporary support, or cable lace anchoring etc. This paper introduces the principle of pre-stressed cable bolting and the specifications of the Cable-Lok anchor, presented the testing results in laboratory and the application cases in mines.

Oct 1, 2010

By Ta M. Li, Russell A. Carter

The first century of mining in northern Idaho's Couer d'Alene District will soon he drawing to a close. Like so many other great raining districts, it has been a period accompanied by a rich and colorful history. From its early days as a gold rush camp, the district has evolved into the leading silver producer in the US, but the going has not been easy: early-day labor disputes, the challenge of mining for profit in some of the deepest mines in the Western hemisphere, and the constant search for new reserves at great depths have taken their toll of mines-and miners-along the way. To these traditional mining problems have of late been added the burden of inflationary cost increases, pollution control, and reclamation. A recent visit to the district by MINING ENGINEERING, how ever, revealed that the deep commitment of the operating companies and the quiet competence and vitality of their engineering personnel are key factors in the continued prosperity of the district.

Jan 7, 1976

By J. A. G. Llerena, J. Sattarvand

Tailings dam failures have been occurring in recent years. They are considered more vulnerable than hydraulic dams due to the lack of regulations on specific design criteria, and stability requirements regarding monitoring during the construction and maintenance process. Thus, monitoring the dam is essential to know the dam's existing state and ensure its safety. One of the reasons tailings storage facilities fail is slope instability caused by moisture content. A relationship does exist between moisture content and surface strength, early detection of seepage would help to assess the physical condition of the dam. Moreover, to cover the tailings dam area in an efficient way Unmanned Aerial Vehicles (UAVs) are suitable because of their versatility and high-resolution data acquisition. Mounted with a high-resolution RGB camera, and thermal, or hyperspectral sensors UAVs can acquire good quality images that combined with image analysis and machine learning algorithms yield a good estimate of soil moisture.

Feb 1, 2023

By Hannan J. C

In New South Wales, development applications for major coal mining proposals are determined by the Minister for Planning and Environment and applications for mining leases and other mineral titles are dealt with by the Minister for Mineral Resources. The environmental conditions placed on the development consent, the coal mining lease and the approvals and licences under the pollution control legislation, amount to a substantial component of any new project's planning and commissioning considerations.An outline is presented of the framework within which various approvals are granted and conditions for environmental management are imposed upon mining projects. The principles and concerns, as perceived by the regulatory authorities, on which the majority of approval conditions are based are also outlined.No attempt has been made to analyse the extent to which these principles or standards are achieved in practice, nor to discuss the degree to which some of the conditions are achievable with the current status of technology and economics in the coal industry.

Jan 1, 1987

By Charles L. Kimbell

The year 1980 on the whole was not a good year for the world's mineral industry. The general upturn of activities in 1979 after a rather poor 1978 showing was not maintained with a number of key measurement standards showing downturns. Most notably, the world's steel and petroleum industries recorded significant reductions in output, the former in response to markedly lower demand levels and the latter partly in response to lower industrial consumption owing to general economic conditions and partly owing to successes in campaigns for the reduction of energy use in general and petroleum product use in particular among major importing nations that were feeling the trade balance pinch of ever-higher oil prices. During 1980, a number of political events-some international in scope, some confined to single nations-had significant influence upon world mineral industry activities and mineral commodity supplies, and other political happenings had the potential to significantly affect the industry in future times.

Jan 1, 1982

Konkola No 3 shaft experienced severe mining-induced stress and time-related deterioration in ground conditions in an area where an over-cut and bench (OCB) mining method was used to extract a shallow dipping wide orebody. This caused an unacceptable risk for safe mining operations to sustain the required levels of production. After a review of the conditions it was decided to change the mining method to CASCADE to recover ore in the affected area and modify the OCB method and use a modified over-cut and bench method (MOCB) for new mining sections. This paper describes the geotechnical criteria included to derive the mining standards for the MOCB. The geotechnical risks are identified and taken into account to develop stope design parameters, stoping sequences and support requirements. A monitoring programme to assess conditions as mining progresses is also discussed.

Jan 1, 2005

Very few of those occupied in pursuits other than mining have any conception of the extent of boring operations that have been carried out on the gold and coal fields of Victoria, or of the valuable and definite knowledge obtainable by such means. The subject comprises various branches, which it will be necessary to describe in detail. The three main divisions are The Administrative, which includes all financial work and general management. The Professional, dealing with topographical and geological work necessary before any scheme of boring can be laid out, the preparation of plans, the inspection of cores obtained from bore holes, the examination of diamonds, etc. The Mechanical Branch, dealing with the drilling machinery, setting of diamonds, maintenance of stores, etc. In 1877, the Goverpment of Victoria decided to assist in prospecting the mineral resources of the colony by the aid of diamond drill boring, and for that purpose, a vote of £5,000 was passed, with which were purchased three diamond dulls, an American type being adopted.

Jan 1, 1901

Geometallurgical Study of Copper Oxide Mineralisation Hosted in Gravels of Different Physical Quality

Sep 13, 2010

By Guillermo Velarde

Dado que la flotación seguida por la fundición/ refinación es la única vía de procesamiento del cobre, se buscó una alternativa que trate con suficiencia los sulfuros de leyes marginales dentro del CUT-OFF de una concentradora. En ese sentido, el presente texto señala que la energía solar se convierte en una herramienta que ayuda a lixiviar minerales con poca pirita y obtener una temperatura de proceso que magnifica la recuperación del cobre en especial de la calcopirita, etc. Asimismo, la influencia cuantitativa de la temperatura en la recuperación de los sulfuros primarios, transicionales y secundarios de cobre, la velocidad de calentamiento de la pila, las temperaturas de proceso que puede alcanzarse, las pérdidas de calor en el periodo no soleado del día, el balance térmico de la pila y otros indicadores económicos de viabilidad, etc. son presentados como resultados de pruebas diversas a nivel de laboratorio e industrial.

Oct 21, 2015

By James P. Sloss

WHAT is the likelihood if any-that a real gold mining industry will be developed in the southern Appalachian region? Has the increase in the dollar value of gold from $20.67 to $35 per ounce potency to turn the trick? Suppose it be assumed that the price of gold will, at worst, not recede, and that the cost of digging ore and treating it of which the average level of commodity prices and wages is a fair index-will, at most, not exceed that prevailing in 1926. One may or may not accept these as reasonable assumptions; but one must arbitrarily remove some of the potential variables if one is to get anywhere on a problem like this. As a matter of fact, this article is not going to venture a conclusive answer to the question that has been posed; but it will endeavor to present some of the factors that have a bearing on the problem. The writer spent ten days visiting a dozen properties in Virginia and the Carolinas early in April, 1935, and in doing so got a first-hand slant on mining conditions in the domain of King Cotton.

Jan 1, 1935

By A. E. Ketler

Conventional Atmospheric Monitoring System (AMS) installations for monitoring CO, CH4, O2 and air-velocity throughout underground mines are usually relegated to a modest 3-5 mile extent and with data communication speeds confined to a ponderous 1-5K baud range. New US-MSHA and state regulations require fast reporting of unsafe conditions, and the old 20-30 minute updates are no longer acceptable. To communicate farther and faster has always been a problem, because data reliability degenerates with excessive distances and high speeds. Because of this, very large mines often resort to costly optical-fiber media, using expensive OF cables and repeaters to obtain the necessary coverage. This entails high initial cost, as well as high maintenance and downtime costs to repair or replace broken optical fibers. Rel-Tek has pioneered with its DX-Bus communication data highway, which uses inexpensive twisted-pair telemetry cables, which can now communicate well into the 20-mile extent of the largest mines -- normally a brick wall for low-tech AMS systems. This extended range, enables the use of twisted-pair cables and provides a low cost alternative to OF systems. This paper discusses the DX-Bus, and its latest accomplishment, the ?B-LINK,? a unique high-speed communication repeater that maintains the 19.2K-Baud data rate. On-going innovations to our workhorse Millennia-DX computer software have kept pace with this extra speed/distance phenomenon, resulting in a dually-optimized AMS package: both hardware and software. Cost savings are substantial, and at no sacrifice of reliability ? nearly always at 100%. Sensor updates are measured in seconds, not minutes and hours. Twisted pair copper cable is cheap to purchase and install and a breeze to maintain. Rel-Tek uses the B-LINK's wide branching capabilities to enable the AMS to extend 20-miles both far and wide. Actual experience in large US coal mines -- both longwall and continuous mining operations -- confirms the large mine performance. The ventilation and safety benefits to the mining industry are immeasurable.

Jan 1, 2009

By H. Jalkanen, L. Holappa

The main role of slag in oxygen converter processes is to absorb the non-volatile oxidation products of hot metal impurities, Si, P, Mn, Ti, V, etc. The importance of converter slag as deP and de Smedia has ceased with implementation of special pre- and post-converter treatments. The transfer from top blowing (LD) to combined blowing converters has decreased the amount of slagged iron that, together with the tendency towards lower silicon and manganese contents, has decreased slag to steel ratio. Still the control of slag forming and behaviour during the blow is of great importance. In this paper the thermodynamics of the slag forming reactions, the role of slag in the modern oxygen converter process for impurity elimination, splashing, lining wear, dust formation and post combustion are discussed on the basis of common knowledge and experience of Finnish steel plants.

Jan 1, 2004

By Gus Van Weert, Peter Kondos

"Ore sorting has been quite successful in providing a separation means in the rock size range of 1 to 6 inches; a range where mineral dressers do not have many options. The industrial minerals and recycling worlds have embraced this technology. However, ore sorting has not found wide application in the base or precious metals mining industry. One reason for this is thought to be the reliance of most sensors on rock surface characteristics, not very useful in case of sulphides, non-existing in case of gold. Microwave heating, however, is specific for sulphides and graphite (or carbonaceous matter) embedded in the rocks; washing or even drying does not appear necessary. Separation can be done afterwards by already existing ore sorting technology using infrared sensors. Test results on six Nevada gold ore samples are presented in detail. Some simple test procedures are also presented for those wishing to explore the microwave potential of sulphide sorting in their own operations.INTRODUCTIONMineral processing in the base metals industry most often involves upgrading of the ore, concentrating the valuable mineral fraction by classic methods, such as flotation. Since the liberation of minerals in the ore occurs mostly at or below the 100 micron level, the industry has been living with fault lines, so to speak, between blast hole spacing (10,000 mm), run-of-mine ore size (100 mm) and beneficiation size (0.1 – 0.01 mm). The acceptance of ore sorting will inevitably lead to the revisiting of the following questions: “Exactly how much below ore grade rock ends up in the mill because the geologists or the miners cannot define the resource boundaries more precisely? How can the economics of dilution be improved? How many ore grade rocks are lost with the overburden?”"

Jan 1, 2007

By JOHN W., E. C. SARCENT

The South Texas area discussed herein represents districts 2 and 4 of the Texas Railroad Commission. It extends from Jackson, Lavaca and Gonzales Counties on the northeast to the Rio Grande River, and comprises a total of 26 counties.

Jan 1, 1946

By Woodhouse M, Andrews D, Drew G

The nickel deposits within the Honeymoon Well project area (26¦ 40'S, 120¦ 25'E), located 45 km south of Wiluna, occur in the northern part of the Agnew-Wiluna belt (Figure 1; Hill et at, 1990). The project area is covered by up to 50 m of transported material which greatly hampers both exploration and an understanding of the bedrock geology. Since 1990 intensive exploration has increased the resource from 10 Mt at one per cent Ni to 134 Mt at 0.76 per cent Ni in five deposits (0.4 per cent Ni cut-off, resources above 300 m depth, December 1994). This includes a massive sulphide resource of 2.5 Mt at 3.4 per cent Ni.

Jan 1, 1996

By G. E. Jones, G. K. Hoffman

Through the USGS National Coal Availability pro-gram, two San Juan Basin studies have been completed. The study areas are in the northwest Bisti field, Fruitland Formation and in the eastern Standing Rock field, Menefee Formation. Original resources are 4.66 Gt and 3.46 Gt (5.14 billion stand 3.82 billion st), respectively, in the Bisti and Standing Rock areas. Bisti coal resources are greatly reduced by the Bisti-De-Na-Zin wilderness area (1.13 Gt (1.25 billion st)). Technological restrictions remove 31% from Standing Rock original resource. Available resources are 60% (2.79 Gt(3.07 billion st)) of the Bisti original resource and66% (2.26 Gt (2.49 billion st)) of the original Standing Rock resource.

Jan 1, 2000

Pulverized Fuel Combustion The apparatus shown in the illustration is a complete equipment f r supplying coal to boiler and metallurgical furnaces, cement and lime kilns, dryers, and to all furnaces requiring a temperature and quality of fame under prompt and easy control. It is claimed that the Aero Pulverizer makes practicable the highest efficiency obtainable from burning coal. It makes coal burn like a gas, a flame, the physical and chemical character of which is regulable- a flame that may be elongated or shortened, thus placing the zone of highest temperature where needed- a flame that may be made oxidizing, reducing, or neutral, as occasion may require. The coal is burned as pulverized, and there is no storage of the powder with its attendant hazard. Artificial drying before pulverizing is not necessary if the coal supply be sheltered from rain and snow. Where the Aero is used, it is wholly a furnace question whether a dryer should be installed; it is not at all a pulverizing or storage question. Labor is reduced to a minimum. Slack coal at low cost yields its last B.T.U.

Jan 11, 1915

By R. K. Singhal

Canada is a world class producer and exporter of minerals and mineral products. Today's highly mechanized Canadian open pits use state-of-the-art equipment and support technology. They are taking advantage of larger equipment, including in pit crushing and conveying, truck dispatch systems and electronic management tools. Mine planning is computerized. Environmental issues are dealt with in all phases of planning, and equipment modifications are pursued to keep them functioning in the hostile Canadian north. In 1991, Canada's mineral production (excluding fuels but including coal) totaled $C 16.9 billion, a decline of 13.8% from the 1990 total of $C19.6 billion. It is a major producer of nickel, zinc, asbestos, potash, molybdenum and uranium. Canada is also an important source of copper and iron ore (Fig. 1).

Jan 1, 1995

By Olav Mellgren

Part I. The interaction between potassium ethyl xanthate and lead salts has been studied thermo-chemically. It is shown that ethyl xanthate reacts with lead carbonate, basic carbonate, thiosulfate and sulfate according to principles of simple chemistry, whereas reactions with lead sulfite, metasulfite, basic thiosulfate and hydroxide at high pH are associated with secondary reactions. A new compound "xanthogen thiosulfate" is postulated. Part 11. Adsorption of ethyl xanthate on galena has been studied quantitatively and thennochemi-cally. It is shown that an ion-exchange mechanism governs the adsorption process and that the heat of adsorption of xanthate on galena is equivalent to the heat of reaction of ethyl xanthate with bulk lead salts. It is concluded that the entropy content of the surface "compound" on galena is different from that of a corresponding bulk lead salt. Alkali depression is in part shown to be due to the instability of the xanthate-galena system at high pH and to the formation of basic lead salts. Sulfate and carbonate ions are shown to have a stabilizing effect on the xanthate-galena system. PARTI. THERMOCHEMISTRY OF ETHYL XANTHATE AND OF ITS REACTION WITH LEAD SALTS In the past little attention has been paid to the chemistry of lead xanthate. It is known that xan-thates form slightly soluble compounds with lead and that suspensions of lead xanthates in alkaline solution decompose rather readily.' The solubility of lead ethyl xanthate is of the order of 2.6 x 10-6 moles per 1. At increasing pH the xanthate concentration of a saturated solution contains more xanthate. Thus at pH 11 this xanthate content is about 100-fold larger than at pH 7.1 Xanthates are known to be consumed when added to a suspension of slightly soluble lead salts such as lead sulfate and lead carbonate. It is unknown to what extent this xanthate consumption is due to a simple chemical reaction because, frequently, observations are made which reveal secondary reaction products in such reactions. Thermochemical study of the reaction between xanthate and lead salts offers a means to clarify the significance of these reactions as the enthalpy changes can be accurately predicted from heat of formation of lead salts in pure solution reactions. In the present work the heats of formation of lead ethyl xanthate from potassium ethyl xanthate and lead salts are determined and some thermochemical aspects of xanthate in solution are studied. The results of these investigations are presented in Part I. In Part II the heat of adsorption of ethyl xanthate on galena surfaces is presented. All enthalpy changes were measured directly in a microcalorimeter. Calorimeter: The calorimeter used for measuring enthalpy changes was similar to that used by Redinha and Kitchener2 which was based on a description by Derbyshire and Marshall.3 Other useful references4,5 are listed. A sketch of the calorimeter

Jan 1, 1967