Search Documents

By R. J. Hundermark

Keywords: Anglo American, Anglo Platinum Ltd, Waterval, Mortimer, Polokwane, ACP, pyrometallurgy, platinum, PGMs Anglo Platinum Ltd is the largest primary platinum producer in the world and operates three smelters in South Africa: Waterval, Mortimer and Polokwane. The operational details of the smelters are covered in previous reviews, thus only unit operations that have been upgraded are discussed. The most significant of the upgrades include the installation of a second ACP converter at Waterval Smelter in 2006 and the anticipated upgrade of Mortimer Smelter to 38MW in 2011. Several advances have been made in the smelting operations to improve the furnace stability and longevity. Control of the chromium input to each of the smelters has substantially allowed continued operations at levels below the spinel saturation point in slag, which results in lowered matte and slag temperatures. Mogalakwena concentrate, arising from the Platreef ore, is used to dilute high chromium-containing concentrates. In addition, furnace controls have improved in terms of crucible temperature and condition monitoring, improved feeding control, management of alarms and trips and having the quality of instrumentation and operational rigour required to support this. Advances have been made on the ACP converter in terms of good converter matte quality, and increased intensity and efficiency of operation. Combined with improvements to both the conventional and tower sulfuric acid plants, the emissions from Waterval Smelter have been reduced substantially since the introduction of the ACP. This is in spite of increasing metal throughput. The Anglo Platinum Ltd smelting operations have made significant progress since 2006 and further advances are envisaged to further improve on safety, reduce costs, increase efficiencies and throughput, while reducing emissions.

Jan 1, 2011

By W. Dingley, G. R. Hoey

"Thirteen Canadian sulphide ore mines were surveyed for corrosion control. The mines visited were a small, yet representative, proportion of this segment of the Canadian mining and metallurgical industry. Information on metallic corrosion and methods used to control it in underground workings and mills was gathered (a) by discussing corrosion problems with company personnel, (b) by examining equipment and structures during under-ground and mill tours, (c) by photographing corrosion sites, and (d) by collecting and analyzing mine water samples.The corrosion survey, which is summarized in the re-port, leads to the following general conclusions. Mine environments are corrosive, particularly when the mine w1a-ter is acidic. Because of a lack of good corrosion control measures, excessive deterioration of equipment due to corrosion occurs in mines. Mill environments are also corrosive, but in some cases good preventive measures are being taken to effectively control corrosion losses.Ways to reduce corrosion losses in sulphide ore mines and mills are discussed. The main areas for more corrosion research and development are selection of materials of construction, protective coatings, cathodic protection, inhibitors, equipment design, and mining and milling practices."

Jan 1, 1971

By P D. Katsabanis

This chapter describes the principles for the derivation of the equations for a detonation wave. The importance of the equation of state for the detonation products is demonstrated and commonly used equations of state are discussed. Furthermore a brief introduction to the TIGER code is presented.

Jan 1, 1991

By Ed Billington, Mike Shields

The trail blaster is faced with a wide range of workrelated challenges, not the least being the work setting itself. It is usually remote, being anywhere from 5 to 30 or more miles (8 to 50 km) from any road. It may be in mountains, high rock desert, or coastal rain forest, and can range from sea level to over 12,000 feet (3700 m) in elevation. The blaster may be part of a 2-person clearing crew, a 4-person maintenance crew, or a 10-person construction crew. The crew will usually be mobile, moving and working up to 10 miles (16 km) or more per day, relying mostly on their own backpacks to move camp, tools and supplies from site to site. Periodic resupply may be by helicopter, aird rop, or even “sherpa” groups, but most often will be by packstrings of horses and mules. The crew goes into the backcountry a n y w h e re from two weeks to three months at a time, and while there, its members “live the job” 24 hours a day, enjoying baking heat, torrential rain or mid-July s n o w s t o rms along with the truly glorious weather that c o m p e n s a t e s . So who is this blaster? Well, “he” may be she, since some of the top trail blasters are women. He/she will also be more than a blaster: Crews are small, so experienced members must be capable of handling the full range of trail work. Thus this blaster is also a driller, and usually also a bucker, snag faller, rigger, dry-stone mason, log and timber carpenter, bridge builder, mule p a c k e r, small-engine mechanic and, not least, camp cook capable of putting out a hot meal from a campfire , in a downpour, in the dark. Being in remote locations, often without reliable communication to the outside world, trail crews enjoy a remarkable degree of independence from “supervision.” With that comes the responsibility to make sound decisions which expedite the work, while promoting crew safety and welfare .

Jan 1, 2004

The cost of preparing a feasibility study is notoriously difficult to estimate. Studies for mining projects are typically commenced when an exploration programme has identified a mineable resource and pre-feasibility studies have shown that development of the resource would lead to an economically viable project. Pre-feasibility studies will normally include an estimate of the cost of a formal feasibility study and this estimate would then be firmed up before a commitment is made to proceed with the formal study. Data for preparing the feasibility study cost estimate will be sketchy, geological investigations, metallurgical testwork, and marketing studies may be needed before the scope of the project and hence the scope of the formal study can be finally determined. Before an estimate of the work required and hence of the cost of the feasibility study can be prepared the source of project funds must be decided. Studies for internally funded projects are often less rigorous than those which must be "bankable" and subject to the scrutiny of external financial institutions. This paper sets out suggestions for preparing more accurate cost estimates for feasibility studies by ensuring that all activities are included and shows how a staged approach to preparing such studies can minimise costs and guard against cost overruns. It also provides a case study showing how the estimate compared with actual costs for a recent feasibility study completed by Pancontinental Mining Limited.

Jan 1, 1990

By S. S. PRENZ

Discussion held at the sessions of the Canal Zone meeting, November, 1910. [SECRETARY'S NOTE.-As a result of this discussion, an expression of opinion covering all points of unanimous agreement was adopted and signed by members of the Institute party as individuals. This statement, which was printed in the Bulletin of December, 1910, is reprinted below, as an introduction to ,the detailed report of the discussion. It should be clearly understood that it does not constitute an official declaration by the Institute, the rules of which forbid any such action. At the New Haven meeting of February, 1909, a free discussion of the plan of the canal took place, in which the critics of the present scheme had full opportunity to state their views. That discussion was continued at considerable length in the newspapers ; but the Institute was never committed to either side. In this latter instance, the situation is precisely similar. Certain members and guests of the Institute, having had the advantage of later developments and of personal inspection, have expressed the conclusions at which they have arrived on their own responsibility ; and these conclusions are published by the Institute, subject to further discussion, like any other part of its proceedings. The general statement referred to contained a promise that the full discussion, of which it was a result, would be subsequently printed ; and this promise is fulfilled, so far as practicable, in the subjoined report, concerning which I beg to offer the following explanations: 1. It is made up of the remarks of the members of our party, as subsequently written out and mailed to the Secretary. 2. In editing these contributions, I have condensed the material considerably by cutting out much repetition of opinions and phrases ; and in such excision, I, frankly confess, the authors whose communications were delayed, have been the sufferers. Nevertheless, there is a good deal of repetition left, as there must be, when so many persons had talked so much, and come to agreement upon so many points. 3. It has been found impossible to preserve in this report the actual order of the free and informal oral discussion represented. Consequently the several contributions have been arranged in alphabetical order under the names of their authors. References to "preceding speakers," etc., must therefore be construed as referring to other speakers, preceding or following.-R. W. R.] S. S. PRINZ AUGUST WILHELM, AT SEA, November 14, 1910. We, the undersigned, members and guests of the American Institute of Mining Engineers, after a visit to the Isthmus of Panama, and inspection of the work of the United States Isthmian Canal Commission, and after full discussion of our individual impressions, find ourselves in unanimous agreement as to the following conclusions:

Jan 1, 1911

By Jimmy Rodríguez Las Heras

Durante la explotación de los niveles inferiores en la mina Yauliyacu, se generaron dudas sobre la ubicación de las concentraciones de esfuerzos y sus relaciones con los estallidos de roca. En este sentido, se instala un sistema microsísmico donde mediante el análisis de la microsismicidad se elaboró los estándares que permitieron reducir los incidentes por estallidos de roca presente, así como la frecuencia, magnitud y daños a las personas, y equipo e infraestructura de mina, debido a la energía liberada por los eventos microsísmicos. Por ello, el presente trabajo señala los beneficios del uso del sistema de análisis de microsismicidad como la actualización contínua de la zonificación minera de acuerdo a la concentración de esfuerzos, procediendo al reforzamiento del sostenimiento como medida de prevención.

Sep 21, 2013

By Thomas T., Read

IT is difficult to judge how much influence the success attained during its first year, 1864-65, by the School of Mines at Columbia had on developments in education for the mineral industry elsewhere in the immediately subsequent years. The facts are as follows: 1. The Massachusetts Institute of Technology began giving instruction in February 1865, with a mining course included in its curriculum. 2. Early in 1865 the faculty of the Department of Science, Literature and the Arts of the University of Michigan requested permission from the Regents to establish "a course of study to be called the School of Mines . . . Also that the degree of Mining Engineering, be conferred on students who should complete the course of study prescribed in the same." A resolution authorizing this was adopted by the Regents on March 28, 1865. 3. Samuel Hooper endowed a Sturgis-Hooper professorship of geology at Harvard in 1865 with the intention of making it a nucleus of a new School of Practical Mining and Geology. 4. Yale appointed Alfred P. Rockwell professor of mining in 1865. 5. Lafayette College appointed Henry S. Osborn professor of mining and metallurgy in 1865. 6. Washington College (as Washington and Lee was then known), rising out of the ashes of Civil War destruction, made a fresh start in 1865, with Generalized as its president, and offered a mining course in the first catalogue thereafter published. 7. Lehigh University, founded in 1866, had a mining curriculum from its beginning. 8. Rensselaer Polytechnic began offering a curriculum in mining and metallurgical engineering in 1867. It would be natural to suppose that these events were a reaction, to the success of the school at Columbia, - and possibly they

Jan 1, 1941

By M. W. BERNEWITZ

IT is 27 years since I last visited Broken Hill, New South Wales, one of the world's greatest lead-silver-zinc districts. Then, the flota¬tion of ores was in its infancy. The Minerals Separation process had its birth as a practicability in the Central Mill, which is still operating and yielding high recoveries. The average Australian knows that Broken Hill is an important mining center in a "corner" of New South Wales, but he does not know what a factor it is in the lead, silver, and zinc production of the world. Nor does he realize that among the ramifications arising from metal production at Broken Hill are the great lead smelter at Port Pirie, South Australia, 254 miles southeast; the electrolytic zinc works at Risdon, and the limestone mine at Davenport, Tasmania; the acid works at Cockle Creek, New

Jan 1, 1935

By I. B. Tulu, M. M. Sears

In 2015, 40 longwall mines provided nearly 60 percent of U.S. underground coal production. During this time, about 80 percent of ground-fall-related fatalities occurred in areas where the mine roof was supported. In an attempt to better understand the status quo of current longwall support practices in the United States, during a period between 2010 and 2017, researchers from the U.S. National Institute for Occupational Safety and Health (NIOSH) visited a sample of 25 longwall mines representing nearly 50 percent of the currently active longwall mines operating in all of the major U.S. longwall producing regions. The data presented here indicate that the types and amount of roof support being installed in modern U.S. longwall mines have reduced ground-fall accident and injury rates to levels never seen before. However, the complete elimination of unintended roof falls in U.S. longwall mines has remained elusive. The data in this paper can be used by mine operators and engineers to determine where their chosen type and density of roof support occur on the spectrum of observations contained in this database. Additionally, this data can be used to enhance, supplement and support additional research on longwall gateroad support systems. 

Some form of technical library is a necessity for every metallurgical plant, but its form and scope will vary with the conditions of each case. In its simplest form, it may consist of one or two mining journals and a few text books distributed amongst the staff. Again, it may be a separate establishment controlled by a clerk, the technical staff necessarily making its own research into the literature available. A still more elaborate organisation may be established both to supply information when requested and to keep the operating staff in touch with current matters of interest, and the library service of the Electrolytic Zinc Co. of Australasia is of this character.The necessity for such a service is due to several facts. The Company's interests are scattered over three States. Most of its staff members are remote from: good public library facilities and they have few opportunities for exchanging ideas verbally with other metallurgists and engineers. Then, too, the process of recovering zinc by electrolysis, is a young art of which the physical and chemical bases were far from fully known at the time the: Risdon plant was established. Most of the zinc produced is sold abroad, and this unsheltered industry can afford to miss no technical or economic development which may promote its efficiency. Add to these facts the geographical isolation of the Commonwealth and the case for an adequate library is complete.

Jan 1, 1934

By B. A. Wilcox

ThERE are several reports in the literature which indicate that both solid-solution hydrogen and hydride precipitates can promote low-temperature em-brittlement of tantalum.1-3 For example, Imgram et al.2 showed that hydrogen additions in the range of 140 to 580 ppm promoted a ductile-to-brittle transition at slightly above room temperature in both wrought and recrystallized tantalum. This contrasts with the observation that tantalum of norma1 purity is very ductile, even at liquid-nitrogen temperature. Imgram et al. also found that hydrogen additions caused a deterioration of notch tensile properties of tantalum. The purpose of this communication is to present some limited evidence that hydrogen can also cause fatigue embrittlement of tantalum. The material used in this investigation was wrought, stress-relieved (1000°C, 1 hr), are-melted tantalum rod (5/8-in. diameter) containing the following impurities in weight percent: 0.005 C, 0.007 02, 0.0005 H2, 0.003 N2, 0.08 Cb, 0.01 W, and 0.01 Fe. Hydrogen charging was done in an atmosphere of flowing dry hydrogen for 3 hr at 600°C, followed by an homogenizing anneal in purified argon for 15 min at 600°C, and cooling in an argon atmosphere. Typical micro-structures of the hydrogen-free and the hydrogen-charged materials are shown in Fig. 1(a) and Fig. 1(b), respectively. Fig. 1(b) shows the appearance of hydride precipitates which, in many cases, formed preferentially parallel to the rod axis. The hydride dispersion was uniform across the diameter of the specimen. The fact that the precipitate was a tantalum hydride was tentatively confirmed by X-ray diffraction on a metallographically prepared surface. After hydrogen charging, chemical analyses by vacuum fusion revealed the hydrogen content to be 0.0295 wt pct. In addition, the oxygen and nitrogen contents were slightly raised to 0.0095 O2 and 0.005 N2.

Jan 1, 1964

By Bjöm Böhle

Top-down construction (or cut and cover construction) is providing important advantages when comparing with conventional construction techniques for commercial developments with deep basements, underground car parks or near surface infrastructure and traffic tunnels. Main features are substantially reduced restrictions to surface usage, avoidance of intervention with adjacent property, provision of rigid substructures resulting in minimal deforma­tions and settlements and, last but not least, accelerated construction pro­gramme. The present contribution illustrates the construction method in general and elaborates in detail on the special foundation works for a major urban commercial high rise development requiring a six level basement structure.

Jan 1, 2006

By P. K. Hofmeyr

Base Metal (Cu, Ni, Mo, Zn, Co etc.) analysis traditionally has been very slow in conventional analytical laboratories which can lead to additional costs being incurred in waiting time of drill rigs or mining excessively off-reef. Recent developments in the automation of analytical laboratories now allow for very rapid turn-around times for base metal analytical data which can help reduce such costs as well as reduce the unit costs of the analyses themselves. 2.0 CONVENTIONAL ANALYTICAL LABORATORY PRACTICE Conventional analytical laboratories are necessarily are very manual. Sample preparation is slow and laborious, samples are moved from stage to stage manually and, typically, all samples are processed in batches so a sample which is the first to be, say, milled has to wait for the complete milling of the batch before it advances to the next stage eg. mixed with wax prior to pelletising for XRF analysis. Inevitably this results in long sample data turn-around times for laboratories handling large numbers of samples. Manual sample preparation can only be accelerated by increasing staff which increases costs and can lead to additional errors being introduced. Cleaning of sample preparation equipment, eg. crushers and mills, between samples is essential to avoid cross-contamination between samples and this is slow and labour-intensive. In manual sample preparation the correct sample numbers staying with the samples is totally dependent on the efficiency of laboratory operators. It is extremely difficult to detect when errors have occurred due to the switching of sample numbers during the sample preparation stages. Running duplicates and QC samples at best is only partially successful in detecting when sample number switching errors have occurred. Errors of this nature and cross-contamination problems due to incomplete cleaning of sample preparation equipment tend to occur when laboratories are working at pressure due to high sample numbers and when supervisors are not present during 24/7 laboratory operations which is often required on plant process control laboratories. These problems are common to all conventional analytical laboratories and their magnitude is dependent on the level of control and efficiency of QC systems practised by individual laboratories. The disadvantages of conventional manual analytical laboratories can be summarized as follows:- 1. Labour-intensive which is costly especially when multiple shifts have to be used during 24/7 operations.

Jan 1, 2005

By K. Thuro, R. J. Plinninger

ABSTRACT: Determining tunnel stability is a key issue during preliminary site investigation. In contrast, problems of excavatability have been largely ignored. While the choice of an economic tunnelling method is admittedly a clear priority in the planning stage, special investigations focus-sing on rock fragmentation (e.g. drilling or cutting performance, rock mass blastability or tool wear) are rarely carried out. This paper explores possibilities to quantify key parameters for rock mass excavatability in drilling, blasting and cutting by TBMs and roadheaders. RÉSUMÉE: La détermination de la stabilité du tunnel est une question clé lors des études prélimi-naires. En revanche, les problèmes d'excavabilité sont souvent en grande partie ignorés. Tandis que le choix d'une méthode de percement économique est évidemment une priorité claire dans l'étape de planification, des investigations spéciales se concentrant sur la fragmentation de la roche (par exemple le comportement de la roche au forage, à l’excavation ou au dynamitage et l’usure des outil) sont rarement effectuées. Cet article explore les possibilités pour quantifier les paramè-tres clé de la roche lors d’excavation par forage, dynamitage, au tunnelier (TBMs) ou à l’excavatrice. ZUSAMMENFASSUNG: Beim Tunnelbau wir meist die Vorhersage der Stabilität des ausgebrochenen Hohlraums als Schlüsselfragestellung betrachtet. Im Gegensatz dazu werden Probleme der Gebirgslösung weitgehend ignoriert. Während der Wahl einer wirtschaftlichen Vortriebsmethode während der Planungsphase meist noch eine gewisse Priorität beigemessen wird, werden spezielle Untersuchungen zur Gebirgslösung (Bohr- oder Schneidbarkeit, Sprengbarkeit oder Werkzeugverbrauch) nur sehr selten durchgeführt. Diese Publikation zeigt Möglichkeiten der Quantifizierung von Schlüsselparametern für die Gebirgslösbarkeit auf, also der Bohr- und Sprengbarkeit, der Fräsbarkeit mit Teilschnittmaschinen und der Schneidbarkeit mit TBMs.

Jan 1, 2003

By M. Jeffrey

This study investigated the elution of precious and toxic metals from activated carbon. Gold and mercury are of primary interest, due to their value and environmental impact respectively. A laboratory elution rig was commissioned to simulate industrial Zadra and AARL carbon elution conditions. Mercury was found to elute most effectively in strong caustic cyanide solutions; gold was found to elute most effectively in hot low ionic strength solutions. As cyanide decomposes on contact with activated carbon at high temperatures, optimum elution conditions for gold conflicts with those for mercury?no practical compromise in conditions was found. However, sequential elution allowed reasonable recovery of both metals. Ongoing work is looking at the deportment of other metals under elution conditions.

Jan 1, 2009

By M. Prats

Most of the information available on the heat efficiency of hot fluid injection processes, both water and steam, has been obtained from calculated temperature distributions in the pay zone and adjacent formations. The usual approach has been to write the heat balance equations in terms of the temperatures, and then to introduce whatever simplifications are necessary to help obtain an analytical or a numerical solution. In either case, the assumption has often been made that the vertical thermal conductivity in the flooded interval is infinite, so that the temperatures within the flooded interval are then independent of vertical position. Because it was first made by Lauwerier,l and has been used extensively since, this assumption will be referred to as the Lauwerier assumption. Excellent reviews of the literature on the heat efficiency of hot fluid injection processes have been given by Spillette,2 Flock et al.,3 and Ramney.4 Of course, the most significant contributions take into account the effect of a finite vertical thermal conductivity on the vertical temperature profile. The most general analytic expression for the heat efficiency of a hot fluid injection process is that of Antimirov5 who considers injection of a heated incompressible fluid into a reservoir through an arbitrary number of wells. The rate of heat injection into the reservoir, as well as the injection temperature, is an arbitrary function of time. The geometry of the horizontal flow is arbitrary, although the reservoir is considered to be of uniform thickness and properties and to be of infinite areal extent. Heat transfer within the reservoir is by horizontal convection and conduc- tion, and by vertical conduction. In the formations adjacent to the flooded interval, heat transfer is by conduction in any direction. Thus, the available expression for the heat efficiency due to hot water injection has been developed for rather general conditions. This degree of applicability has not been obtained for other thermal recovery processes. By making the Lauwerier assumption we have been able to obtain expressions for the heat efficiency that are essentially independent of the thermal recovery process, be it steam, hot-water, or underground combustion. Clearly, then, the approach followed here is more restrictive than that of Antimirov5 in that it uses the Lauwerier assumption. At the same time less restrictive assumptions are made about the horizontal heat transfer mechanisms, either in the flooded interval or in the formations adjacent to it. The main difference between our approach and that of other investigators is that the heat balance in the pay zone is expressed for the pay zone as a whole rather than for a volume element within it. The Lauwerier assumption is introduced after the problem is developed along these lines as far as possible. The details of the development of the heat efficiency are given in the Appendix, while the main features of the model are discussed in the next section. Results and their implications are discussed later in a separate section. The Model Certain assumptions have been made to determine

Jan 1, 1970

The production of metallic titanium and titanium-rich alloys in forms useful to the engineer involves the use of certain techniques not usually necessary in fabricating the commoner metals and alloys. However, not all stages in the handling and shaping of titanium-base materials require the application of unfamiliar methods. It is the purpose of this paper to indicate where the well-known techniques are applicable as well as to outline the unusual operations which are necessitated by certain chemical characteristics of titanium.In brief, the characteristics just mentioned are manifestations of the very great reactivity of titanium, especially at elevated temperatures. Liquid titanium burns vigorously when brought into contact with air. It also reacts with practically all refractories, causing damage to the latter as well as undesirable contamination of the metal. Even solid titanium undergoes serious superficial contamination when heated above 800°C. in air for more than a few minutes. In addition to an oxide skin being formed, oxygen enters into solid solution in the surface of the metal causing the latter to become hardened and eventually embrittled.Up to date, titanium has been made only on a pilot plant scale by methods which produce a spongy or powdered product. Refractory problems have prevented the development of chemical reduction methods for making titanium in the form of a liquid pool from which ingots of useful size could be cast. Therefore the first part of this paper will cover the consolidation of powdered or spongy titanium. The latter portion will provide a brief description of...

Jan 1, 1950

This paper gives an overview of the difficulties associated with determining the strength of hard rock pillars. Although a number of pillar design tools are available, pillar collapses still occur. Recent examples of large scale pillar collapses in South Africa were caused by weak partings which traversed the pillars. Currently two different methods to determine the strength of pillars are used namely, empirical equations derived from the back analyses of failed and stable cases and numerical modelling tools with an appropriate failure criteria. Both techniques have their limitations and additional work is required to obtain a better understanding of pillar strength. Empirical methods are popular and easy to use, but care should be exercise that the results are not extrapolated beyond the range of the data which were used to derive them. An example is the Hedley and Grant formula (derived for the Canadian uranium mines) that has been used for many years in the South African platinum and chrome mines (albeit with some adaptation of the K-value) to design the pillar layouts. Very few collapses have nevertheless been reported and it might even be too conservative an assumption of pillar strength in these mines. As an alternative, some engineers strongly advocate the use of numerical techniques to determine pillar strength. A close examination unfortunately reveals that these techniques also rely on many flawed assumptions. An area where numerical modelling is invaluable, however, is to study specific pillar failure mechanisms, such as the influence of weak partings on pillar strength. In conclusion, it appears that neither empirical techniques nor numerical modelling currently provide a solid basis to conduct pillar design. It is therefore recommended that both these techniques be utilised when confronted with a pillar design to obtain the best possible insight into the problem.

Nov 25, 2010

The Zeehan field has yielded over 190 000 tons of lead and 26,000,000 oz of silver. Moh of the production took place between the initial discovery of silver-lead ore in 1882 and 1920, and the greatest part was extracted from fissure lodes in the Proterozoic to (?) lower Cambrian rocks. It is demonstrated that the prosperity of the mines relied upon the silver content, which is apparently highest in these beds, particularly where spilitic rocks are associated with them. In contrast, galena occurring in orebodies emplaced in the Gordon Limestone is low in silver.Most of the workings are relatively shallow due in some cases to enrichment related to erosion surfaces.Fault zones within a complex anticlinal structure exposing the Proterozoic to (?) lower Cambrian formations appear to have been major factors in the control of mineralization.

Jan 1, 1968