Search Documents

By Y. Shiraishi, Y. Sakurai

A new method, the gliding cylinder method, was proposed as a wide range viscometer for the measurements of molten salts, slags, and glasses. The method consists of two coaxial cylinders, cylindrical bob and a vessel containing a liquid sample. There is a narrow gap between bob and vessel. When the vessel moves against the bob, the generated force on the bob consists of three types of resistance: (1) Stokes’s resistance on the bob, (2) a capillary flow resistance though an annular gap between vessel and bob, and (3) lubricating resistance in a gap. The last two can be calculated on a theoretical basis but the first cannot be estimated by a simple calculation since a wall effect did not calculate easily. However, it can be assumed that the generated force depends on both the viscosity of a liquid and velocity of the vessel. Thus, the relation between viscosity and a force at desired velocity of the vessel was measured using several standard reference materials including glycerol aqueous solutions and standard reference oils. The results depended on the magnitude of the gap between the bob and the vessel. For the wider gap, it was shown that the viscosity is a linear function of a gradient of force with respect to a vessel velocity. In contrast, if the gap is small, the viscosity depends on the gradient (of force with respect to velocity). This implies that the non-linear phenomena would occur in Stokes resistance. Though detailed analysis is in a further investigation, a calibration method can be applied to determine the viscosity by this method, because good correlation was obtained among these quantities. Viscosity of molten salts, such as NaNO3and ZnCl2was measured by this method as high temperature demonstration. Keywords: viscometer, viscosity, sphere pull-up method, fused salts, molten slags, glass melts

Jan 1, 2004

Capture airborne respirable dust generated by an auger-type continuous mining machine to reduce workers' dust exposure. Approach Install a water-powered scrubber system, operating at 1,400 psi, on the sides of the conveyor. The scrubber draws the dusty air from the face area and discharges cleaned air into the face return. How It Works Auger-type continuous miners pose unique ventilation and dust control problems. To protect face workers from the dust, the end of the brattice is usually maintained close to the face to increase ventilation effectiveness. However, it is taken down as the machine cuts toward the exhaust side to allow the machine to complete its cut. Often, the brattice is not reinstalled in a position to most effectively control

Jan 1, 1989

VISIT TO HENDRINA POWER STATION AND OPTIMUM COLLIERY A visit to Hendrina Power Station and the Optimum Colliery, contractually committed to supply the coal for the power station, took place on the 20th September, 1972. INTERNATIONAL IRON AND STEEL CONGRESS This congress will be held in Dlisseldorf from May 23rd to 30th, 1974. The main theme is "Metallurgical Technology of Iron and Steplml1king".

By V. Koump, T. F. Perzak, R. G. Olsson

Jan 1, 1965

By Rimas Pakalnis, Tom Brady, Lewis Martin

A major focus of ground control research presently being conducted by the Spokane Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) is to incorporate weak rock masses (such as are associated with operations in the Carlin Trend in Nevada) into existing design relationships. The original database that led to most of the empirical design relationships presently employed in hard-rock mining was derived from fair-to-good-quality rock. In this study, the relationship between weak rock quality and opening design (nonentry/entry methods) is being investigated. The common factor in all mines is a weak back or wall. This work attempts to provide tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

By Beevers J

The Ok Tedi Project is now a high production open-pit porphyry copper mine located in the Star Mountains of Papua New Guinea (PNG). At present, total daily production is 190 000t of ore and waste. Large scale drilling and blasting has only been in operation since 1988, prior to which all material was removed by ripping and dozing. This paper reviews the steps taken over the last 12 months in establishing a more efficient drilling and blasting operation and highlights the significant reduction in powder factor. These improvements have been achieved largely through the introduction of air-bags, controlled pattern expansion and an overall focusing on the operation by involving consultants, ICI's technical service and internal departments.

Jan 1, 1991

By W. Carter, P. Chaubal, K. Spaleck, M. Schoeman, J. Bobek, W. Seegers

Keywords: Pyrometallurgy, steel, hearth, blast furnace The Mittal Steel Company operates about 36 blast furnaces on four continents. Furnaces range from 1100 m3 to 4800 m3 inner volume. The focus of the group is to push for increasing productivity and increasing campaign life. This has been especially challenging, as many of these furnaces were not equipped for long campaigns during their prior rebuilds. Monitoring and operating practices have to be modified to match the new philosophy. Mid-campaign hearth repair strategies and hearth design philosophies have had to be reconsidered. The paper describes experiences with the current hearth designs and measures taken for hearth life extension. Additionally, the philosophy of recent hearth re-designs is discussed.

Jan 1, 2006

By Staff

A major emphasis of the U.S. Bureau of Mines is to perform research on the prevention of fatal accidents at mining operations. The leading cause of fatalities in the underground coal mining industry is groundfalls. This proceedings volume presents several new developments that are helping to prevent fatalities and reduce injuries by groundfalls. The papers focus on the problem from two different perspectives. About half of the papers present information and techniques that can be used to train and motivate miners to protect themselves from groundfalls. The other papers explain how to identify and respond to various geologic conditions that affect the stability of the mine roof. Of the 95 groundfall fatalities that occurred during 1986-90, 75% took place in Kentucky, West Virginia, and Virginia. The rate of groundfall fatalities was much higher at small mines. During 1986-90, the rate of groundfall fatalities at mines employing fewer than 20 people was 4.3 times higher than the rate for larger mines. Because so many groundfall fatalities are occurring at relatively small mines in the southern Appalachian coalfields, many of the papers focus specifically on the needs of this category of mine operations.

Jan 1, 1992

By Wilson Blake

Increased application and interest in the use of microseismic monitoring to deal with ground control problems, Particularly those resulting in violent failures, has brought about the need for practical guidelines with respect to all phases of microseismic monitoring. This report presents the results of an 18-month effort to review the microseismic method and develop needed practical guidelines. Microseismic activity and properties of microseismic events are treated so that these parameters can be taken into account when developing monitoring equipment. Microseismic equipment is discussed to provide familiarization with the components of monitoring systems. Factors to be considered and procedures for developing a microseismic monitoring system are presented. Both physical and electrical considerations for the installation of a monitoring system are discussed in detail. The operation of a microseismic system including data analysis procedures is presented. Field examples to illustrate use of microseismic data in evaluating ground control problems are presented in a number of case histories.

Jan 1, 1982

By R. Knapp, R. Firlotte

"Les Terrains Auriferes (LIA) Property, formerly the Malartic Goldfield (Goldfield) mine, ceased its remaining milling operations in the fall of 1994. During the early years of mining, the mill processed a non-sulfide ore with substantial carbonate mineralization.In 1977 after an extended shutdown period, ore from a nearby property, Bousquet, was processed at the mill. That ore contained larger quantities of sulfides, and unlike the old tailings, had acid generating potential.Upon closure of the L TA mill, the closure options considered for the L TA site were to cover with:1. a thin cover of 0.5 metres of borrow material (sand and gravel) to achieve basic erosion protection/stabilization; collect acidic seepage and treat with lime.2. a 2 metres of non-acid producing tailings; final surface to be vegetated.3. an engineered oxygen barrier consisting of a multi-layer cover; final surface to be vegetated.The paper presents the technological and economical methodologies that were used to select the closure alternative, describe the associated construction challenges that were faced with the implementation of the multi-layer cover concept and presents preliminary results on the cover's performance.In addition to being the first full scale demonstration of this type of multi-layer engineered oxygen barrier cover technology, this project had the advantage of using non acid producing mine tailings as part of the reclamation solution."

Jan 1, 1997

By Secis R

Northparkes Mines is located 27 km northwest of Parkes in central west New South Wales. The E26 deposit is the largest of all defined to-date in the area, containing over 50 per cent of Northparkes' resources and reserves. The combination of orebody geometry and geotechnical characteristics provide ideal conditions for the block cave method of mining of the first lift of the E26 deposit. Although this method of underground mining has been used for decades in other countries, E26 is the first example of its use in Australia. Copper-gold mineralisation at Northparkes is related to quartz monzonite porphyries that have intruded coeval Ordovician volcanics. Sulphide mineralisation (dominantly bornite and chalcopyrite) occurs principally within quartz veins associated with the porphyry intrusions. Veining and mineralisation occurs within both the porphyries and volcanics. To optimise the recovery of a resource within a block cave mine, a good understanding of the rock mass and ore flow characteristics is essential. These have a significant effect on the fragmentation size and range and on parameters such as the drawzone spacing, height of interaction zone and dilution entry. As ore within a cave column moves and mixes when material is extracted from below and beside it, the total reserve extracted is unique for a particular draw strategy/production history. Until recently, reserve estimates and production schedules were based on the application of a uniform dilution factor to the tabulated resource. However, given the complicated flow and mixing within the cave column, such a simplistic approach can produce erroneous results. Northparkes Mines purchased and sponsored the upgrading of a commercially available software package specifically developed for modelling removal of resource blocks under caving conditions. This Gemcom software package, PC-BC, has been used for mine planning, reserve reporting and production scheduling. Blocks within it resource block model are converted into a mineable reserve taking into account mixing and dilution during depletion of drawcolumns (by horizontal and vertical redistribution of insitu tonnage and metal). As PC-BC gives individual drawpoint reserves, it can be used during the planning stage to determine whether or not a drawpoint is economic. For E26 Lift I an optimal layout containing 130 drawpoints has been developed based on a nominal 14 m x 14 m drawpoint spacing and a 0.8 per cent equivalent copper (eCu) cut-off grade. Annual production schedules for the depletion of material above this layout are based on: I higher tonnage removal from higher grade drawpoints in the early years of production; and 2 drawpoint production rates proportional to the total tonnage of orr remaining in the drawcolumn up to the optimal height of draw tier subsequent years. The reserve is tabulated from the combined annual production schedules over the life of the lift. The pre-mining reserve for Lift I of E26 is 26.6 Mt at 1.43 per cent copper and 0.39 g/t gold, of which approximately 23.4 Mt will be extracted under caving conditions. By scaling down the annual production schedule, weekly drawpoint tonnage calls can be given for short-tern production scheduling.

Jan 1, 1997

By T. B. Colman

Paper presented at the MEP '89 conference held in Madrid, 13-15 November 1989. Britain has sustained an important metalliferous mining industry over many centuries. Recently, new geological concepts and exploration techniques have indicated that there is considerable potential for the discovery of a variety of deposit styles, often in previously neglected areas. The recent discoveries at Aberfeldy (Ba-Zn-Pb), Gairloch (Cu-Zn) and Cononish (Au-Ag)in Scotland and Curraghinalt (Au-Ag) and Lack (Au-Ag-Pb) in Northern Ireland are illustrations of this potential. Some of the prospective areas for future exploration are described and an indication is given of the legislative framework within which mineral exploration and development are carried out

Jan 1, 1991

By Transfert Environment and Society

Transfert?s added value ? Building bridges between project promoters and communities ? Unique expertise in working toward Social License to Operate through meaningful community engagement ? 25 years of recognized innovation and a systematic approach ? Key mining clients: ? Royal Nickel Corporation ? IAMGOLD - Niobec ? Richmont Mines - Wasamac ? Mine Arnaud ? Managem

Aug 1, 2013

By John Freer

On 25th November, 1983, nearly forty members of The South African Institute of Mining and Metallurgy, together with Doris Gardner and Judith Money from Kelvin House, travelled by luxury motor coach to Secunda, there to visit the coal-mining and conversion operations of Sasol Limited.

Jan 1, 1984

By R. A. D. Pattrick, R. A. F. Ixer

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. At Calliachar Burn, 14 steeply dipping quartz-sulphide veins, with and without gold, infill master joints that crosscut gently dipping metasediments and metabasics of the Pitlochry Schist Formation. The wallrock is extremely bleached and enriched in sericite, chlorite and carbonate. Gold grades vary from high with quartz-galena-pyrite to low with galena-chalcopyrite; the gold forms electrum inclusions smaller than 20 micrometres in pyrite or, rarely, arsenopyrite. At Urlar Burn, gold is present in small amounts in 4 quartz-galena-chalcopyrite veins. Although much of the mineralogy is similar to that at Calliachar, there are significant differences in Sb-, Te-, Bi- and Hg-bearing phases. Fluid inclusion data suggest mineralisation occurred over the range 320-140 degrees C, from fluids with significant CO2 and 2-13 wt% equiv. NaCl. Mantle-derived fluids appear to have been generated during the late Caledonian and focused by the Urlar Burn fault

Jun 19, 1905

By C. A. Pryor

The aggregates industry is the largest minerals industry in the United States producing over 2.6 billion metric tons of crushed stone, sand and gravel annually. Approximately 5% of that production is fine material, passing a 75-micron mesh sieve. Of that amount, about 77% is not sold and represents one of the major industry issues. The material accumulates in stockpiles and settling ponds having an operational and economic impact on the site’s bottom line. Many factors cause this material to be produced: from blasting and processing techniques all the way to end use specifications.

Jan 1, 2002

Samples weighing 0·5 g are decomposed with hydrofluoric and other acids. Most elements are extracted ftom the acid, aqueous solution by Alamine 336 (tricaprylyl tertiary amine) and thorium is determined in an aliquot taken from the aqueous phase by means of its reaction with arsenazo III. Concentrations down to 4 p.p,m. may be determined at a rate of 100 samples per man-day of 8 hr.

Jan 1, 1971

This report presents the results of a study of mill tailings disposal practices and potential tailings dam stability problems. Recognizing the long period of time that would be required to develop the technology and practices necessary to significantly improve refuse disposal safety, the Bureau initiated this research effort as a first step in that development. Volume 1 includes a summary of conclusions and recommendations resulting from the overall research effort; discussions of disposal systems and methods, geology, seismicity, hydrology, and materials characteristics; evaluations of investigational techniques; discussions of usable interim generalized investigational, analytical and inspection procedures; discussion of general principles and presentation of a tailings technology manual outline; and discussion of needed future research am recommended programs.

Jan 1, 1974

This paper aims to collate the metallurgical test work undertaken on the Barrytown mineral sands deposit. It is intended to serve as a summary of mineral dressing work undertaken by all interested parties up to the time of writing. Areas requiring further investigation are: in situ grades and recoveries of accessory minerals,the question of 'rank' of ilmenite within the deposit,flow sheet development for the recovery of gold and monazite, andcost analysis to investigate the relative worth of other minerals; notably rutile. Flow sheet development with respect to the Accessory Minerals cannot be accurately defined until the importance of each mineral in terms of grade, recovery and expected revenue is determined. To date, ilmenite and zircon flows are well documented. Further work is needed to quantify recovery's and flows of the other minerals; notably monazite, gold and rutile.

Jan 1, 1989

By Mark S. Sanders

The purpose of the present study was to develop and test improved Type V workvests for use on dredge operations. The goal was to design workvests that would be more comfortable to wear, would interfere less with task performance, and would better meet the needs of dredge workers. It was hypothesized that by attaining these goals, the resulting vests would be worn more often and would be kept buckled more of the time than traditional vests. The study involved three major phases. In Phase I, visits were made to dredge operations and a definition of the problem was developed. Problems with current vests were identified and working conditions and tasks surveyed In Phase II, prototype vests were developed and laboratory tests were per-formed to assess comfort and interference. In Phase III, the prototypes were modified and field tested with actual dredge operators and workers.

Jan 1, 1985