Search Documents

By W Shamu

The mechanical properties of rock samples of identical lithologicalcomposition may vary significantly due to existence of materialdiscontinuities. Laboratory tests were carried out to determine the effect of material discontinuities on rock sample mechanical properties. The investigations consisted of detecting discontinuities, observing the failure mechanisms during uniaxial compressive strength tests, and analysing of the factors affecting the strength. A non-destructive testing method has been adopted to assist in thedetection of discontinuities. Laboratory testing proved that fractures leading to failures initiated on the detected discontinuities. The location, orientation, size, density and extent of the discontinuities contribute to different modes of failure and these affect the mechanical parameters of rock samples. Four modes of failure were distinguished for hard and brittlecylindrical rock samples. These modes were referred to as simple shear failure, multiple shear failure, multiple fracturing and vertical splitting. To evaluate the effect of discontinuities on mechanical parameters, the ratio of uniaxial compressive to tensile (Brazilian) strength was calculated and analysed for the different modes of failure. It was found that the value of the ratio depended on the mode of sample failure. The lowest value of the ratio was observed for shear mode of failure and the highest for vertical splitting mode of failure.

Jan 1, 1999

By David S. Yang

The construction of Oakland Airport Roadway Project for the airport expansion requires stabilization of subsurface soils for the construction of three grade separation structures at two roadway interchanges and the intersection of a roadway and taxiway serving the airport. Loose sandy fills and soft Bay Mud were improved by Cement Deep Soil Mixing (CDSM) for the construction of a soil-cement foundation under the MSE (Mechanically Stabilized Earth) walls of a roadway overcrossing and a soil-cement gravity retaining wall to maintain stability of a roadway undercrossing during and after a major earthquake. CDSM was also used to construct two cutoff walls for groundwater control. A test section was carried out prior to full production to verify that the CDSM equipment, installation procedures, and mix designs could produce the soil-cement with required strength, uniformity, and permeability to meet the design intent. Additional test sections were performed for the confirmation or modification of the mix design and installation procedure to cope with the complex subsurface conditions resulting from the historical development of the site. The test section revealed that the CDSM cutoff walls, retaining wall, and foundation improvements could be constructed to satisfy the design requirements and that the intermittent test sections alleviate the impact of the varying subsurface conditions. Based on the data obtained from the test sections, one CDSM cutoff wall was completed in July 2000. Full production of the CDSM retaining wall, cutoff wall, and foundation began in March 2001 and is expected to be complete in November 2001.

Jan 1, 2001

By K. J. Bathe

The current version of the computer program ADINA/BM (Automatic Dynamic Incremental Nonlinear Analysis for the Bureau of Mines) for linear and nonlinear, static and dynamic finite element analysis of mine structures is described. The complete report is divided into four parts. In Part A the program solution capabilities, the finite element library, the logical construction of the program and storage allocations are discussed. In Part B the theory and numerical techniques used in the program are summarized. In Part C brief problem descriptions and solution results for some sample solutions that have been transmitted as data cases with the program are presented. In the last section of the report, Part D, the users? manual of the program is presented. Program ADINA/BM is a general effective tool for coal mine structural analysis. The program is an extension of the computer program NON SAP (which was developed under an earlier contract with the U.S. Bureau of Mines). The important additional capabilities of ADINA/BM are: (1) the occurrence of all elements is time dependent, (2) all elements can be used in geometric and material nonlinear analysis, (3) the truss element can be used in elastic-plastic analysis, (4) the three-dimensional element can be employed in orthotropic, elastic-plastic and cracking and crushing analysis, (5) the program executes an out-of-core solution and thus allows the analysis of very large and complex coal mine models, (6) the truss elements can be employed as 2-4 variable-number-nodes elements, (7) a rock material model has been implemented, (8) displacement constraint equations can be imposed in the solution, (9) more flexibility in specifying the incremental solution strategy and an acceleration procedure in the equilibrium iteration are available

Jan 1, 1978

By S. Sridhar, R. E. Aune, M. Hayashi

Thermophysical properties of silicate melts are strongly structure dependent. It is well known that the viscosities of slags increase with increasing the degree of polymerization of silicate anions. Even the thermodynamic properties of slags are dependent on the types of species and the population of the same in the melt. Thus, a link between the thermophysical and thermochemical properties of silicate melts is logically expected. The present paper elucidates the salient features of Darken?s excess stability approach to the Gibbs energies of solutions as applied to the viscosities of silicate melts. It is demonstrated, that the second derivatives of the viscosities of binary silicate melts with respect to composition indicate a maxima corresponding to the existence of stable compounds in these systems. The concept was successfully applied to the following systems: Al2O3-SiO2, CaO-SiO2, FeO-SiO2, MgO-SiO2and MnO-SiO2. In all the cases, the second derivative plots of viscosities with respect to composition showed peaks corresponding to the metasilicates. The second derivatives of the activation energies of viscous flow with respect to temperature has earlier been shown to reflect the formation of associates/embryos in the homogeneous silicate melts, indicating the readiness of the melt to separate a solid phase. Thermodynamic coupling of thermal diffusivities in the case of the system CaO-Al2O3-SiO2from the laser-flash measurements of these slags as a function of temperature are examined as part of the present study. Densities are estimated from integral molar enthalpies in the case of silicate systems and the results are presented. Keywords: silicate melts, viscosity; activation energy, thermal diffusivity; density

Jan 1, 2004

During the period 1979 thru 1982, Multi Mineral Corporation conducted a mining research program at the United States Department of the Interior's Bureau of Mines Oil Shale Mining Environmental Research Facility in the Central Piceance Creek Basin, Rio Blanco County, Colorado. The program consisted of mining, environmental and geotechnical research data and. the results are described in this report.

Jan 1, 1983

By Y. Mao, D. Xie

The viscosity of TiO2-containing blast furnace slags may increase rapidly (commonly referred to as thickening) under strong reducing conditions in the blast furnace. To elucidate the mechanisms for slag thickening, measurements have been made of changes in the composition and rheological properties of TiO2-CaO-SiO2-Al2O3-MgO slags during the reduction process. The slag composition covered the range of 17–33 wt% TiO2, 9–19% Al2O3, 8–16% MgO and theCaO/SiO2from 0.8 to 1.4. The viscosities were measured using the rotating cylinder method at temperatures up to 1550ºC and the fusibility temperatures were determined from ‘breaks’ in the viscosity-temperature curves. The reduction of the slag was carried out in graphite crucibles at1500ºC for 2–6 hours The rheological properties of the slags during reduction were predominantly influenced by the slag basicity (CaO/SiO2), and the effect of other components depended largely on basic or acidic behaviour of the oxide. The reduction of TiO2in the slag by carbon was initially fast to formTi2O3, followed by further reduction to TiO and TiC. Correspondingly, the viscosity showed initially a slight decrease, followed by a gradual and then rapid increase. The thickening was found to be accelerated by an increase in TiO2content and a decrease in the CaO/SiO2in the slag. In addition to the existence of 1~3 wt% TiC, the thickened slags also had a significant amount of TiO (3~7 wt%), suggesting that TiO may play an important role in the ‘thickening phenomena’ ,possibly by forming solid solutions with TiC to significantly increase the number of solid particles in the heterogeneous slag. Keywords: TiO2slags, viscosity

Jan 1, 2004

By J. Jones-Parra, R. S. Reytor

The porosities of fractured limestone reservoirs can be divided into two broad types in accordance with their effects on fluid distribution and fluid flow. In the coarse porosity, gravity segregation lakes place freely and the resistance to fluid flow is very small. In the fine porosity there is no segregation and a high resistance to flow, and it has relative permeability characteristics similar to tight sandstones. By analyzing the affect of the two porosities it is concluded that in some cases to recover the maximum amount of oil it is necessary to remove large quantities of gas from the reservoir by producing at high gas-oil ratios. In this manner the fine porosity is drained of its oil and the gas-oil contact drops slowly permitting higher production rates from the oil leg. Since this conclusion is contrary to widely accepted principles of conservation, a mathematical model (Fig. I) was constructed to duplicate the conditions desired. The behavior of the model indicates that under certain conditions it is possible to recover more oil by producing at high gas-oil ratios than by production at low gas-oil ratios, and that the rate of production is affected more by gas shut-offs than by the decrease in pressure (Figs. 2, 3, 4 and 5). INTRODUCTION It has been noted that certain limestone reservoirs behave in such a way as to indicate that there are two distinct types of porous spaces available for fluid storage and fluid flow. Regardless of the nature of these porous spaces the distinguishing characteristic is that in one type of porous space there is definite gravity segregation between the oil and the gas; while in the other, the gas evolved tends to remain distributed equally throughout the reservoir. For the sake of simplicity the porosity in which gravity segregation takes place at a fast enough rate to affect the behavior will be called "coarse po- rosity", while that in which this is not so will be termed "fine porosity". The behavior of a reservoir of this type would be different than that of a sandstone reservoir, especially if most of the oil is in the fine porosity. It has been observed that fluid flow to the wells takes place mostly through the coarse porosity. The large fractures which

By E. H. Izen

A thermal imaging borehole probe was designed and fabricated for the purpose of obtaining thermal images, through smoke, of objects and people in underground mines. The effort was basically unsuccessful; electrical noise, and possibly thermal noise, interferred with the desired signals to the extent that spatial resolution in the images was unacceptable.

Jan 1, 1980

By B. Gigas, M. Preston, M. Giralico

Optimized mixer settler designs will now handle total flows of over 6,000 m3/hr.Computational Fluid Dynamics (CFD) is a timely and predictable tool for design development. Lightnin has the capability of using numerical analysis methodology to evaluate flow patterns and phase separation. CFD can show performance differences between changes, in mix tanks, in settler geometry, and in liquid depth, against variable flow rates. Understanding the differences allows the development of optimized designs. This paper focuses on the major design components of the mixer settler and how technological advances will lead to further improvements, when designing for today’s largest flow plants.

Jan 1, 2004

By Jason M. Ryan

"Along with recent advances in computer technology have come cost-effective systems desiiedto evaluate fragmentation distributions through digital images of particles. In mining operations andmineral processing plants, important data from these systems is obtained through monitoring sizedistributions at key stages of the comminution process. Blast engineers apply this technology as atool for the validation of empirical fragmentation models so that predicted results are more meaningful."

Jan 1, 1998

By H. H. Murray

Recently developed clay deposits that will impact regional and world markets are described. These deposits, their location, geology, and physical properties are delineated. Kaolins from the State of Para in Brazil and from Ukraine; bentonites from Argentina and India; and palygorskite and sepiolite from China are world class deposits that when processed using modem technology will produce excellent products. Other deposits that may affect regional markets are kaolins from China, Australia and Indonesia; bentonites from Georgia (formerly USSR) and China; and palygorskite from India and Ukraine. New ball clay deposits that will affect regional markets are in China and Indonesia.

Jan 1, 1999

By M. M. Valenta

A number of challenges face platinum concentrator plant operators. These challenges include the increase in operating costs, the increase in smelter cost for the processing of concentrate, the shortage and cost of power, and the tightening of specifications on concentrate quality by the toll-smelting operations. Over the years the focus has moved from extracting the platinum group metals (PGM) from the Merensky Reef to the UG2 reef. This has a number of advantages, including the higher ?basket price? for UG2 concentrate, reduced mining cost per unit volume as a result of the higher density of UG2, and the reduction in overall concentrate tonnage to be smelted. In many cases the Merensky ore has been fully exploited and it makes sense for the focus to shift to the UG2 ore that can be accessed through the Merensky shaft infrastructure. The presence of relatively high levels of chromite in UG2 concentrate is, however, a major disadvantage due to the problems associated with smelting such a concentrate in conventional submerged arc furnaces. In addition to increasing the specification on the minimum PGM grade of concentrates, smelters have had to impose strict specifications on the levels of chromite in the concentrate. The threat of high penalties has forced concentrators to change their modus operandi, often resulting in a significant loss in recovery. The final concentrate grades and PGM recoveries are shown to vary significantly throughout the industry. The reasons for this include varying ore mineralogy and different operating philosophies. This would therefore imply that the opportunity exists to optimize the operations by considering fundamental aspects such as the PGM mineralogy and the application of appropriate technologies. By returning to the fundamentals of flotation and applying the findings of detailed process reviews, it has been possible to increase the concentrate PGM grade, reduce the concentrate chromite grade, and in some cases increase the recovery of PGM to concentrate. This paper presents case studies where this approach has been used to successfully optimize concentrator performance, resulting in lower operating cost and higher PGM production. Keywords Process optimization, platinum concentrator, milling, flotation, grade, recovery

Jan 1, 2011

A rotating disc geometry was used to provide a uniformly accessible surface for a kinetic study of copper cementation with zinc in sulphate solution. For copper concentrations of the order of 10 p.p.m., a porous, adherent deposit is formed on the zinc surface and this has a significant influence on the reaction rate. When the specific mass of deposit is less than about O· 35 mg/cm2 the surface may be considered as smooth and the rate is described by simple convective counter diffusion of zinc and copper ions through a laminar diffusion boundary layer to the deposit-solution interface. In the presence of additional deposit, the diffusional mass transfer rate is increased by increased surface roughness.The rate under these conditions is first order, with the degree of enhancement independent of further increases in the specific deposit mass. The enhancement in rateis, however, directly related to the initial mass flux and the species involved in the reaction.Preliminary work showed the same mechanism to apply to cementation from chloride solution, solutions of high zinc concentration, and cementation of copper with iron..

Jan 1, 1970

The treatment plant at Martha Mine was upgraded from a nominal throughput of 110tph (O.93mtpa) to 150tph (1.25mtpa) late 1999. Post-upgrade performance did not meet expectations when treating either the competent primary ore or the clay-rich oxide ore.   ò Plant throughput is constrained by milling capacity when treating the competent primary ore. This is not an issue at present as current plant feed is oxide ore from the top of the open-pit, but will become so in future years as the pit deepens. To counter this future threat, ball mill power has been restored to 1100kW through modifications to the drive train. The addition of a crushing circuit may also be necessary.   ò Plant throughput was originally constrained by thickener and leach/adsorption tank issues when treating the oxide are. Changes to plant equipment and operations has seen the removal of these constraints and throughput on this material is no longer a problem.   The most significant issue facing plant staff at present is the high silver grade and its impact on gold recovery. These high grades impact upon recovery through losses caused by insufficient leach and adsorption capacity. To counter this, the geology, mining, and milling teams are working together to blend the high grade silver zones with lower grade ores - this is seen to be the quickest and most cost effective way to deal with the issue. The plant design has also been evaluated with a view to modifying it to cope with the higher silver grades. The viability of these modifications will depend on cost and time (that is, the length of time to implement any modifications versus the length of time to mine out the high silver zones).

Jan 1, 2001

By S. O?Connor

When one looks back and does assessments of what has been the key ingredient in achieving success in our safety efforts, there are many issues that spring to mind and cover a wide array of elements. One does not know which has the ultimate maximum effect. In his presentation yesterday, Alan Peers, our SHEQ leader, covered a lot of detail with the way we are managing safety at Modikwa. I have attempted to identify some of the key essentials in making the mine safe. Passion Safety is addressed with a passion that is unbelievable at times. When I get phoned because an incident has occurred and in reporting the incident, there are already action plans being put in place to prevent re-occurrences, you understand the commitment to put employees? safety first. You hear the disappointment in your subordinates? voices when they have to share the fact that an incident or accident has occurred.

Jan 1, 2011

By Fernando Humberto Muge

One of the problems that arises in the early stages of the mine planning before the determination of the mining exploitation method is to predict what will be the recoverable ore reserves in tonnage, grade and metal quantity, if the select ion is based upon block grades. The estimation of these recuperation or recoverable functions can act as an important planning tool in what concerns the appraisal of the consequences of ore-waste discrimination of individual blocks in a selective mining operation. Estimation methods of all these functions are discussed together with cross validation tests using the available information concerning a preliminary drilling campaign accomplished during the exploration stage of an iron orebody located in the North of Portugal (Moncorvo Orebody).

Jan 1, 1982

By Jacolien P. Wyethe

Zincor uses a Roast-Leach-Electrowinning circuit to process zinc sulphide concentrates. It also processes zinc oxide fume, originating from a slag smelting operation in the Democratic Republic of the Congo (DRC). Zincor achieved an average zinc recovery of 90.3% during the period January 2006 to May 2007. The bulk of the losses occurred in the iron and lead silver residues, both as soluble and un-dissolved losses. The un-dissolved losses in the iron residue constituted around 33% of the total zinc lost from the circuit, and were largely attributed to the presence of zinc-ferrite in the calcine used for neutralization during iron removal. As part of Zincor?s continuous improvement programme, the un-dissolved zinc losses in the iron residue were targeted by: the partial replacement of calcine with zinc oxide fume (from the DRC); and the preferential use of ?low-ferrite content calcine? as neutralizing agents in the iron removal circuit. These initiatives, coupled with other operational factors, resulted in a marked improvement in recovery to 92.6% during June to December 2007. The zinc oxide fume, directly fed to the circuit, required investigation of the halide rejection capacity of the Zincor circuit. Rejection of chloride via the magnesium bleed operation was considered adequate. Fluoride was mainly rejected via the iron (~70%) and lead silver (~27%) residues. Fluoride rejection via the lead silver residue varied significantly, probably as a result of variations in the sparingly soluble CaF2 content in the feed. The mechanism for fluoride rejection in the iron residues is uncertain. The fluoride rejection capacity of the Zincor iron residue (comprising of mainly jarosites, schwertmannite and ferrihydrite) at 2 ? 4 mg/L F in solution, was estimated at 0.14 ? 0.19 kgF/tFe residue.

Jan 1, 2008

By P. F. Kerr

This is not a conventional professional paper. It deals mostly with personal experiences. These concern a background in applied mineralogy. Your committee asked me to do this. I accepted with a California enthusiasm which has since diminished with the approach of a Chicago winter. Nevertheless, I wish to thank your committee and also to apologize in advance for omissions and inadequate statements, as such a paper must possess. My introduction to applied mineralogy took place in 1922 at Stanford University. Physicists had recently demonstrated that crystalline powders would reflect x-rays in a systematic manner. Professor A.F. Rogers sug¬gested that significant x-ray reflections might be obtained from powdered opaque minerals. With the aid of Professor D.L. Webster in the Physics Department, I constructed an x-ray diffraction outfit. It was a crude affair, but it worked. Starting with 1924, we secured recognizable patterns of a goodly number of ore minerals (1,2,3). Today x-ray diffraction outfits are common, and a card system of mineral identification is constantly used.

Jan 1, 1981

By António A. Henriques, António Gomes Correia, Ana Teixeira

"Abstract Pile foundations are often used for important structures, and thus, reliability evaluation is an important aspect of the design. Reliability methods have become increasingly important as decision support tools in different areas. The main benefit of reliability analysis is that it provides quantitative information about the parameters (uncertainties) that most significantly influence the behaviour under study. In particular, the design of pile foundations still involves many limitations and uncertainties, particularly when there is not enough investment in soil characterisation and/or pile load tests. In addition to the uncertainties associated with soil characterisation, physical, statistical, spatial and human uncertainties exist. In this subject, the primary purpose of this paper is to demonstrate the application of reliability methods to geotechnical pile design (axial load). It also presents a simple and practical approach to performing it using Monte Carlo Simulations, intending to provide knowledge for code harmonisation and encouraging the development of such methodologies in geotechnical practice. Sensitivity analyses are shown to understand the influence of each uncertainty type coming from different sources. An application example indicates, corroborating other studies, that the model error is the most influent uncertainty. As such, when using the different models (SPT-, CPT- and PMT-based) for bearing capacity, the results emphasise the need for a well-defined and wellcharacterised resistance model, also these results allow the engineer to understand how important the load tests can be to achieve reliable results and economic designs.1 IntroductionUnlike the approach to reliability evaluation used in structural engineering, the traditional procedure used in geotechnical designs addresses uncertainties through high global or partial safety factors (SF), mostly based on past experience. However, this approach to addressing uncertainties does not provide a rational basis for understanding their influence on design.Furthermore, the new regulation codes and social concerns, such as the sustainability or the economy, are imposing geotechnical engineers to increase their ability to deal with uncertainty in a direct and more rational way. Designs should be economic, sustainable and reliable at the same time. Concerning the reliability part of design, different approaches can be done, but the most important thing to keep in mind is the simplicity and efficiency of the tools and applied methods."

Jan 1, 2014

By W. E. Brown, P. R. Porath, V. Miller, C. E. Wood, C. Prasky, E. P. Barrett

"INTRODUCTION This investigation was a part at the Bureau of Mines program for the production of critical and essential materials needed for the war.The Boykin Committee for investigating the steel shortage aided in obtaining an appropriation to be expended by the Bureau of Mines in studying the utilization of North Dakota lignite in the manufacture of hydrogen that could be used in the production of sponge iron from low grade ores of Minnesota.OBJECT OF INVESTIGATIONThe investigation was conducted by the Bureau of Mines to ""determine the workability of the proposed bubble-hearth process and its possible use in connection with an experimental plant for the gasification of lignite being operated by the Coal Division of the Bureau of Mines at Grand Forks, North Dakota.ACKNOWLEDGMENTSThis report is one of many on various aspects of the Bureau of Mines program directed toward the more effective utilization of our mineral resources.Investigations of our mineral resources are conducted by the Mining Branch, L. B. Moon, chief, and by the Metallurgical Branch, O. C. Ralston, chief.The scope of the report falls in the province of the Metallurgical Branch, whose activities embrace the separation of difficulty beneficiated ores, the production of pure metals from domestic deposits, the exploration of marginal ore reserves, the recovery of secondary metals, and the improvement of present industrial metallurgical practice."

Jun 1, 1947