Search Documents

By Zongliang Zhang

Electrowinning is a significant step in metal extraction processes. Because the nature of electrowinning is to reduce metal from its oxidized state, substantial energy consumption accompanies it. Electrowinning processes of different metals have much in common—the deposition of the metal on the cathode and the counter-reaction on the anode. An advanced model was developed that can be applied to a variety of metal electrowinning processes. A model for specific metals can be readily obtained by modifying parameters such as potential, kinetics, and side reactions in the model. The model incorporates mass transfer, gas-liquid flow, electrochemistry, and deposition, making it a comprehensive electrowinning model. The model is applied to copper, nickel, and zinc and verified with the experimental results. In addition, the parameter settings and results of different metals were compared, showing that this model has great versatility and accuracy, thereby making it an efficient and effective research tool.

By Gerald M. Rich

Magma Copper Company, a subsidiary of Newmont Mining Corporation, has initiated many changes in the continuous casting of 5/16 inch diameter copper rod since startup of the San Manuel rod plant in early 1972. With rod production at forty percent over design capacity, many production records have been established including a record cast of 761 tons of salable rod in a twenty-four hour period. The most challenging and rewarding introduction was the continued utilization of an alloyed copper casting wheel in lieu of the conventional steel wheel. With proper cooling and careful control of the mold release agents. as much as 58.000 tons of copper were cast on a single copper wheel. Other advantages are: 1) Fifteen percent increase in available casting time 2) Reject rod from steel inclusions was reduced by nearly one-hundred percent 3) Wheel cost was decreased by ninety-one percent 4) Natural gas consumption dropped approximately fifteen percent 5) Large increase in refractory component life 6) Reduction of manhours/ton. Many other modifications have contributed to excellent rod quality and high operating efficiency. A two-piece launder was replaced with a single castable launder which reduced oxygen pickup and provided better slag removal. Modifications to the bar preparation unit, pickling system, and coiler resulted in considerably higher milling efficiency.

Jan 1, 1976

By Anxiang Wang, Kunhua Wu, Yifu Li, Junjie Xu, Yongnian Dai, Bin Yang, Lingxin Kong

In this study, the saturated vapor pressures of tin (Sn) and antimony (Sb), the separation coefficient and the vapor-liquid phase equilibrium of Sn-Sb alloy were theoretically analyzed, which demonstrate that it is possible to separate Sn and Sb by vacuum distillation. The process parameters of vacuum distillation, including the distillation temperature, distillation time and alloy mass (thickness of raw materials) on the direct yield of Sn and the content of Sn in liquid phase were investigated by using single factor experiments. The preliminary results show that the direct yield and the content of Sn are 98.77 wt.% and 96.01% with the optimized distillation conditions of a distillation temperature of 1473 K, a distillation t ime for 45 min and a Sn-Sb alloy mass of 125 g ( thickness o f 8 mm). The distillation parameters in the study provide effective and convenient conditions on separation of Sn-Sb alloy.

Jan 1, 2016

By Y. Takasaki

For zinc hydrometallurgical extraction, reducing the electric power consumption of the electrowinning process is an important issue for energy savings. At the Zinc & Lead 2000 symposium, the authors suggested that by using the Pb-0.5%Ag-0.6%Ca alloy, the electrolysis energy can be decreased compared to the conventional Pb-0.9%Ag alloy. In this study, the corrosion behaviors of the Pb-Ag-Ca electrode in a sulfuric-acid electrolyte were investigated. Based on the results Or me Pb-0.5%Ag-0.6%Ca anode after 20 days of electrolysis, the bath voltage and the quantity of anode slime decreased compared to the Pb-I%Ag anode. Subsequently, beta-PbO2 on the electrode surface was detected by XRD and its peaks were sharper than the Pb-1 %Ag anode. Moreover, a dense beta-PbO2 layer on the 0.6%Ca a anode surface was observed. Therefore, it was suggested that the dense beta-PbO2 layer on the anode surface is one of the factors that leads to a lower bath voltage and decreasing quantity of anode slime.

Jan 1, 2003

By Krzyszof Borowiec

With the aim of determining the thermodynamic conditions for sulfation of impurity elements, in particular magnesium, in titaniferous slags the equilibrium gas composition for the sulfation reaction: MO + so2 + 1/2 02 = MS04 has been studied by an EMF technique with a solid zro2 + Cao electrolyte. Here M denotes the impurity elements: Mg, Ca and Mn, and the following _oxide systems have been studied: Ti02-MgO-Fe2 o 3 , Ti02-MnO-Mn2 o 3 , and Ti02 -CaO-Si02 , all in the . temperature range 700-1000ºc. Reproducible EMF values were obtained by adding small amounts of -Na2so4 to the oxide-sulfate mixture. From the observed results the Gibbs energy of formation of the phases Mg 2Ti04 , MgTi03 , MgTi 2o 5 , MnTi03 , CaTi03 , and CaTiSio5 , as well as the activity of MgTi05 in the solid solution with Fe2Ti05 have been calculated. The results show that, from a thermodynamic viewpoint, sulfation of these impurities in titaniferous stags i:s favorable- at around and below 800ºC.

Jan 1, 1985

By Satoshi Itoh

Phase equilibria and activities of the components in the liquid lead-antimony-oxygen ternary system, which is of fundamental importance for discussing the' recovery of lead and antimony from a used lead-battery, have been investigated at 1173 and 1223 K. The two liquid phases of metal and oxide were observed at the temperatures studied, and the tie lines indicating isoactivities were determined. The activities of PbO, SbO1.5 and Sb2O3) in the PbO-SbO1.5 and PbO-Sb2O3 pseudo-binary systems were then obtained by applying the Gibbs-Duhem equation to the phase relation of metal-oxide equilibrium. Both in the pseudo-binary systems the activities exhibit negative deviations from Raoult's law. The vapor pressures of lead, antimony and lead oxide, antimony oxide were calculated by using the activities of the components in the lead-antimony-oxygen ternary system. As a result, an oxidation of antimony concentrated in an anode slime followed by evaporation as antimony oxide Sb406 was found to be considerably effective for the recovery of lead and antimony from a used lead-battery.

Jan 1, 2003

By C. Koopman

During the production of phosphoric acid from phosphate ore and sulfuric acid, large amounts of calcium sulfate are formed, in which impurities from the feedstock are incorporated. To use the calcium sulfate in, for example, the building industry, a lower concentration of impurities is desired. Mercury, copper, lead, and cadmium were extracted from clear industrial recrystallization acid (0.8-3.9 mol/kg H3PO4, 0.2-0:5 mol/kg H2SO4) by supported solvent extraction with the extracting agent Cyanex 302 in kerosene in a transverse flow hollow fiber module. The permeability for the mercury ion was 1.4.10-6 m/s, whereas that for the copper ion was calculated to be 1.5.10 m/s. Cadmium, lead, and copper were extracted during the recrystallization of calcium sulfate hemihydrate to dihydrate, an existing step within the ,phosphoric acid production process, by solvent extraction with the same extracting agent. The concentrations of cadmium and zinc in the newly formed calcium sulfate were proven to be decreased. Unfortunately, concentrations of mercury and lead were too low for analysis.

Jan 1, 1999

By Akihide Nagao

The behavior of impurity hydrogen that is contained in starting material or picked up during processing has been little investigated up to now. The hydrogen microprint technique is applied to determine the microscopic location of impurity hydrogen during deformation in aluminum without hydrogen charging. Three kinds of pure aluminum of 99.99% are prepared, in which hydrogen content is varied by changing the atmosphere when they are melted and heat-treated. After rolling, tensile specimens with a gage size of 4 x 4 rnm and 0.5 mm in thickness are stamped out from these three kinds of aluminum sheets. These specimens are covered with a liquid nuclear emulsion of silver bromide crystals, stretched by 5,10 and 15 percent plastic strain or fractured, developed and fixed. SEM micrographs reveal a number of silver particles on the slip lines and on the grain boundaries. Also shown is that the more hydrogen present in the specimen, the more silver grains appear on the slip limes and on the grain boundaries. Consequently, it is concluded that impurity hydrogen is transported to the surface with gliding dislocations during deformation.

Jan 1, 1998

By Jukka S. Sulanto

Outokumpu has applied its well -known copper Fl ash Smelling Process also for smelting su1phide lead . concentrates. The lead in the Flash Smelting Furnace slag is recovered by reducing the oxygen potential of the slag in an electric furnace by injecting reductant into the slag bath. A series of tests have been carried out in a 1000 KVA electric furnace? adjacent to a pilot Flash Smelting Furnace. The furnace has been fed continuously with molten Flash Furnace Slag. The feed rate has varied from 0.5 to 3.1 MTPH (0.55 - 3..4 STPH) depending on the feed rate and the quality of concentrate to the Flash Smelting Furnace. The inlet slag contained 15 to 40% of lead and the cleaned slag 1. 5 to 3. 0%. The lead recovery from sol id raw material was tested in the same continuous process by feeding lead calcine into the furnace. Feed rate was 0.7 to 0.95 MTPH (0.8 - 1.05 STPH) and the calcine contained 33 to 34% of Pb. Several reduction agents and procedures were tested. The process proved to be suitable for continuous recovery of lead from solid oxide raw materials.

Jan 1, 1990

By Liang Li

Thermodynamic analysis and experiments were conducted in order to verify the feasibility of preparing crude titanium tetrachloride (TiCl4) via the carbochlorination of low-grade titanium slag in molten salt. Titanium slag, assaying 74.6 wt% TiO2 with high calcium and magnesium oxide impurities, was treated by an optimized carbochlorination process in NaCl molten salt. These impurities in the titanium slag were chloridized simultaneously, and chlorination products FeCl2, MnCl2, MgCl2, CaCl2 and CrCl3 were collected in the furnace slag. XRD and SEM/ EDS analysis of residue shown that SiO2 and Al2O3 in titanium slag were difficult to chlorinate completely. Theoretical calculations and industrial-scale experimental studies reveal the content of TiCl4 in the products was more than 98.8 wt% and thus proved the feasibility of utilizing low-grade titanium slag for TiCl4 preparation by molten salt chlorination technology.

By S. K. Kawatra

A growing concern for pyrometallurgical operations is the generation of airborne particulates. These particulates can be generated by combustion processes, or by materials handling. Regulation of these particles by the EPA has become progressively more stringent, first for particulates finer than 10 micrometers (PM10), which are particles fine enough to be inhaled into the lungs. Then, restrictions were introduced on emissions of particles finer than 2.5 micrometers (PM2.5), which are fine enough to become embedded in lung tissues. The next stage of regulations is likely to be ?nanoparticulates,? particles finer than 100 nanometers, which are in a size range where their very high surface area leads to enhanced reactivity. While all of the health effects due to nanoparticulates have not yet been determined, there have been enough studies to indicate that there is a problem, and restrictions on nanoparticulate emissions are only a matter of time. In this paper, it will be demonstrated that dry handling, comminution, and combustion sources represent a significant concern for both PM and nanoparticulate emissions. In regards to dry handling, the effects of utilizing effective dust suppressants on PM and nanoparticulate emissions will be explored.

Jan 1, 2006

By L. Trincado

Mantoverde is a heap leach-SX-EW plant that was commissioned in December 1995 at a production rate of 42,130 ton of copper per year and 5.4 million ton of ore per year. Copper production has steadily been increased to 57,290 ton in 2002. Forecast copper production for 2003 is 60,000 ton for an ore treatment rate of 8.5 million ton. Several improvements in the heap leach process have been implemented. The main process improvements are related to the optimization of heap height, particle size, irrigation rate and leach cycle, in addition to a better heap drainage design and a solution management system. A first dump leach operation was started in 1999 at a production rate of 1,922 ton of copper. A second dump leach operation was started in early 2002 at a production rate of 2,805 ton of copper. Dump leach production will be increased over time to as much as 24,000 ton of copper. The main heap leach process improvements, as compared to the original plant design, as well as the main dump leach operating parameters are discussed in this paper.

Jan 1, 2003

By Li Fangi

This paper describes the characteristics and regularities of a process to recover rare earth minerals from Baotou Ore with H-205 collector. H-205 is a kind of hydroxamic acid with amide as a polar group and poly-cycle aromatic hydrocarbon as a non-polar group, having strong ability to capture RE minerals (bastnasite, monazite). When adding a certain dosage of water glass and some other modifying agents, and maintaining pH value between 8.5 and 9.5, RE minerals can be effectively separated from calcium and barium minerals, such as fluorite and barite, etc. Under normal flotation temperature and concentration, when using H-205 to float RE minerals, it needs a bit longer conditioning time (a few minutes longer than that for the conventional collectors). It is also shown that the reagent has the property of resistance to hard water. The laboratory scale and pilot scale tests of the process have been carried out on bulk froth containing RE minerals and fluorite taken from Ore Dressing Plant of Baotou Iron and Steel Company, in both cases, high grade RE concentrates were obtained and the recovery increased remarkably. Therefore, the process has a great practical value.

Jan 1, 1989

By Baptiste Laubie

Agromining is a phytotechnology aiming at producing commercial metal compounds from low-grade ores thanks to hyperaccumulating plants. The fern Dichranopteris dichotoma is a rare earth element (REE) hyperaccumulator, which naturally grows on former mine tailings in China. It accumulates up to 0.35% of REEs in its aerial parts. Different hydrometallurgical processes are currently developed to recover these elements directly from the biomass or from ashes after combustion. The process presented here consists of a direct extraction by EDTA solution, followed by precipitation with acid oxalic. Optimal precipitation pH and influence of organic matter are determined by modelling and by experimental studies. The final solid contains 4.3% of REEs, with calcium as the main cationic impurity (0.45% of the precipitate). The recovery yield is similar for major REEs and is around 70%. After optimization, upscaling of the process will allow the agromining development to recover REEs from secondary resources with more environmentally friendly techniques.

By R. Cameron

The growing use and acceptance of electric vehicles (EV), as evidenced by the record sales of over 750 thousand vehicles in 2016 and a current global EV stock of 2 million vehicles, is putting pressure on sourcing raw materials such as cobalt, and to a lesser extent, nickel. Global supply is poorly diversified, with 50– 60% of global cobalt production sourced solely from the Democratic Republic of Congo (DRC). One potential source for cobalt and nickel are low-grade nickeliferous pyrrhotite tailings, of which 50–100 million tonnes are present in the Sudbury area alone. This paper presents the extraction of cobalt and nickel from this material using a combination of flotation and bioleaching technologies. The findings of a high-level techno-economic analysis of the proposed processing flowsheet are presented.

By Henry Hu

In high pressure die casting processes, proper control of temperature die yields a high casting production rate and superior quality components, Die temperature is usually influenced by various die design and process parameters such as size and location of intemal water cooling lines, flow rates of cooling lines, and pouring temperature of molten metal. Among them, the cooling water flow rate plays a major role in controlling thermal pattern of the die_ In order to develop an effective control strategy, data of local die temperature must be collected and analyzed, In this study, a PC-based data acquisition and control system (DACS) for die temperature control has been designed, and established, The developed DACS has three input channels for temperature signals and one input channel for water flow rate signals, as well as one output channel for a water pump, and is capable of displaying data in both curve format and value format. Implementation of the DACS in a laboratory setup has also been attempted, It should be pointed out that more advanced control mechanisms can be potentially integrated into this system in future,

Jan 1, 2003

By Christoph Sagadin

Corrosion mechanisms between high melting synthetic ferronickel slags and refractory were investigated. The used slags were prepared by mixing and melting of specific oxides. Substrates of the applied refractory material and specimens of FeNi slags were heated in a hot stage microscope up to 1650 °C. The experiments were performed under a defined gas atmosphere of 60% CO and 40% CO2. A further examination of the formed phases between slag and refractory occurred by scanning electron microscope. The investigations indicate that the slag penetrates between magnesia grains and partly dissolves magnesia. Spot analyses show that iron diffuses into the magnesia grains, which transform to magnesiawustite, meanwhile SiO2 forms different types of olivine like forsterite and monticellite. Thermodynamic calculations confirm the formation of these phases. The combination of practical lab scale experiments and thermodynamic calculations should finally contribute to an improvement of the refractory lifetime and performance.

By Jay R. Hitchings

A technique that enables excellent color photograph production from black and white negatives of electron microprobe x-ray images is described in this paper. The photographs are made by superimposing one, two or three negatives of black and white x-ray images individually through assigned primary color filters directly onto color print paper. When used to examine metallurgical or geological microstructures, the resulting color photograph provides detailed, qualitative information about spatial arrangements, elemental associations and relative concentrations of at least three elements. The technique is simple and straightforward, requiring only standard darkroom equipment. The use of color to display or present complicated microprobe data also allows a non-technical reader or audience to better understand the data.

Jan 1, 1981

By Hannu Johto

Boliden Harjavalta has operated a flash smelter for nickel sulphide concentrates in Finland since late 1959. The original nickel flash smelting process was modified in 1995 to a novel nickel matte smelting (DON) with semi-low iron where the batchwise operated converting became obsolete. Since that, the process has been applied to multiple chemically variable nickel sulphide concentrates with high environmental performance. In this paper, the status of the current smelter operations is described together with the recent modernizations of the nickel flash smelting furnace and the slag cleaning furnaces.

By F. Sanchez, A. Mejias, C. Frias, G. Diaz

"Crude zinc oxides are the major source of secondary zinc and are produced from fuming processes like Waelz kilns. The impurities of crude zinc oxides make difficult their processing in primary zinc refineries due to mainly high chloride tenor. Washing with sodium carbonate is a costly operation and chloride removal efficiency is not good enough, so further purification steps are required. The crude zinc oxides are easily treated using ZINCEX™ technology based on leaching, solvent extraction, and electrowinning. The ZINCEX™ process is commercially available and is designed to be a perfect barrier for metallic impurities and halogens, allowing selective zinc extraction in mixed chloride and sulfate leaching solutions. Other valuable components as lead and silver can be efficiently recovered from the leaching residue using PLINT technology in chloride media. Silver is recovered as silver cement and lead is precipitated as pure lead oxide or carbonate, which can be smelted at low temperature.IntroductionZinc is a fully recyclable metal and at present approximately 70% of the zinc produced worldwide comes from primary zinc while 30% originates from secondary materials. Nowadays, the zinc recycling rate is continuously increasing mainly through galvanized steel scrap processing, and crude zinc oxides are the major source of secondary zinc [1]. Secondary zinc oxides are obtained from fuming processes like W aelz Kiln, Rotary Hearth Furnace or Primus Furnace. Waelz is the dominant technology accounting for 80% of total crude zinc oxides production worldwide. In the Waelz process, steel dust is mixed with solid fuel reductant (coke breeze) and pelletized. It is then fed to the kiln and heated to a reaction temperature of l ,200°C. In such conditions, zinc, lead, and other non-ferrous metals are vaporized into the flue gas together with chlorides and alkaline metals. Mixed oxides are drawn from the kiln with the process gases and separated to produce typical crude zinc oxides [2]."

Jan 1, 2011