Search Documents

By David Bigby

Room and pillar mining with full pillar extraction is one of the most hazardous systems of underground coal mining, a significant hazard being the potential for sudden goaf override. The Autowarning Telltale (AWTT) is a new development for pillar extraction operations, based on the well proven and simple Rockbolting Telltale safety monitoring device. It is now being applied in room and pillar coal mines in India, with significant potential for application worldwide. The Autowarning Telltale is an intrinsically safe low-cost, self-contained unit installed into the roof either during pillar development or prior to pillar extraction. It provides a highly visible warning via flashing Light Emitting Diodes (LEDs) when a preset level of roof movement has been exceeded. The paper provides a full description of the instrument and two case histories of its initial application at fully-mechanized Indian sites using the split and fender technique.

Jan 1, 2011

By Ian W. Farmer

A description of the factors causing outbursts and rockbursts in coal mines is given. The mechanics of both outbursts and rockbursts can be described in terms of conversion of stored strain energy in the coal and surrounding rocks into kinetic energy through failure. The major difference between the two phenomena is that gases adsorbed onto the coal structure and desorbed during deformation contribute to the energy available during outbursts and may also affect the loading and unloading characteristics associated with failure. The amount of energy involved and the type of phenomenon are related principally to gas content depth and rock behavior.

Jan 1, 1988

By Leigh J. Wardle

Significant coal reserves in New South Wales lie under areas with steep topography such as valley slopes and cliffs. Subsidence predictions are difficult to make for these locations as existing empirical databases cannot cover all permutations of topography and mining geometry. Two dimensional numerical model alternatives are of limited applicability. Consequently a novel three-dimensional numerical model is developed including the detailed panel layout, realistic rock mass properties including the full stratigraphy, goat behaviour and actual surface topography. Model results show the same trends as subsidence measurements from Baal Bone Colliery in the Western Coalfield of New South Wales

Jan 1, 1992

By Mohummad Akram

Statistical analysis of multi-seam mining case studies demonstrated that geologic structure and lithological type and sequencing were predominant factors in entry failures. Finite element analysis was used to evaluate the effects of stress field changes on entry instability under differing geologic conditions. Analysis showed the roof to be particularly vulnerable to shear with the location of the failure site changing to meet loading and geologic conditions. Effects of external support on roof stability were examined. Results were correlated with field data to determine stress levels at which failure could be expected to occur. Based on this research design, criteria were developed for roof stability evaluation under specified interactive loading conditions.

Jan 1, 1993

By E. Hosca

Alternative tailgate loading conditions due to conventional and conventional/yield pillar combinations were evaluated to define roof loading. In order to isolate different loading situations, the tailgate entry was considered as part of the roof-pillar-floor system, which is controlled largely by the structural integrity of each member. A data bank of case studies was compiled, which contains details of roof and floor lithology, structure, support, and mining data, including any failure modes. The range of loading conditions that any tailgate can be subjected to was identified to form the basis of numerical modeling. Numerical modeling was then conducted on tailgate openings to determine roof, floor, and rib responses, including failure modes to a variety of loading conditions. Trends developed from the numerical modeling were modified using field data to form the basis for support evaluation and application. The effects of support were modeled numerically to determine optimum load capacity and points of application for reducing the potential for entry failure.

Jan 1, 1994

By Martin Bolesta

The use of strata injection as a means of stabilizing brittle and heavily stressed ground as well as faulted zones is now state-of-the art technology. Users are obliged to select the right combination from a wide range of injection products and equipment in order to ensure that the operation will be a success. Laboratory tests and a fundamental understanding of the technical aspects of injection products not only help in drawing up the correct injection procedure but have in fact become indispensable for planning the most reliable and cost-effective solution.

Jan 1, 2001

By Yingxin Zhou

Data from these field studies and previous case study data have been combined to define ultra-dose seam mining environments and relate them to observed failure conditions. A rating system for ultra-close multi- seam design has been developed and field studies have verified the applicability of the design criteria according to geologic structures, lithology and spatial data. This rating system has been combined with design and depth considerations to create a protocol for quantitatively predicting potential damage in ultra-dose seam mining conditions. A brief discussion of the characteristics of ultra-dose seam mining and its related failure mechanisms is also presented

Jan 1, 1990

By Victor V. Nazimko

Longwall mining technology without interpanel pillars is feasible from a geomechanical point of view. A set of pillarless longwall layouts are proposed including tailentry pillar recovery, headentry pillar recovery and drivage of a new tailentry, partial headentry pillar recovery and combination mining in which advancing panel entries are used for retreating panels. The following mitigative measures are proposed in order to enhance the stability of entries near the panel: driving crosscuts obliquely to the longwall face line, advance support of entries and crosscuts, localized destressing of the chain pillars by horizontal slotting, and partial stowing of the gobs behind the pillars being recovered. A new technology of recovering barrier pillars on the setup entry side is also proposed. This technology uses the same regular longwall face for interpanel pillars extraction.

Jan 1, 1994

By Hanjie Chen

Mining experiences have shown that in a pitching seam, roof behavior is significantly different from a flat seam. Uphill mining usually experiences more roof problems than downhill mining. Based on a case study at RAG American Coal Company, Willow Creek Mine, this paper presents the roof control problems experienced in a high pitching seam. Then, finite element modeling is conducted to analyze the roof stress distribution for an entry developed in different directions relative to the seam strike. The results shows that seam inclination has a significant effect on roof stability in terms of tensile stress. Uphill mining experiences higher tensile stress than downhill mining. The modeling technique utilized in this analysis presents a first of kind methodology.

Jan 1, 2000

By Ben L. Seegmiller

Specially truss systems? including the Intersection Truss®, Continuous Entry Truss®, Cutter Roof Truss® and Roktrus® have been used in many coal mines in the mid- west and western United States during the past four years. These truss systems offer greater strength and support than other standard trusses and many other support devices. Mining operations have found that speciality trusses can give effective long-term support in areas that must remain stable for many years. At some mines, the Intersection Truss® has become the most-widely accepted method of providing secondary support in potential problem areas. Other applications for specialty trusses have included longwall start- up and recovery rooms, arched roofs, access rock tunnels and tailgate entries.

Jan 1, 1990

The applicability of four empirical strength criteria for rock masses, namely, Hoek and Brown, Bieniawski - Yudhbir et al., Rarnamurthy - Arora and Johnston - Sheorey et al. has been tested against the triaxial test data for jointed plaster of Paris of Arora. The following modified Bieniawski criterion shows best agreement with the triaxial test data for jointed plaster of Paris:- where st = axial compressive stress at failure, MPa; s3 = confining pressure, MPa; scm = uniaxial compressive strength of jointed plaster of Paris, MPa; and B = - 3.988 + 9.674 (scm )-0? 185 The modified Bieniawski strength criterion can be used to estimate the strength of a coal pillar, based on a knowledge of stress distribution in it.

Jan 1, 1992

By Q. F. Wang

Spontaneous combustion hazard of loose coal in the top-coal caving region of entry affects the safety of the entry and top- caving longwall face seriously. In this paper, by combining on- site temperature tests with lab tests and numerical simulation, the characteristics of microcirculation close to the top-coal caving region are analyzed. A model for the temperature fields of the microcirculation in loose coal is presented. Based on this model, the temperature distribution and possible self-ignition region can be predicted. Further, the heat and mass transfers in microcirculation are studied. Finally, the mechanism of oxygenation during the spontaneous combustion of microcirculation in loose coal of the top-coal caving region of entries is put forward. The research results in this papa may provide ideas for the prevention and putting out of the fire caused by spontaneous combustion in the caving zone.

Jan 1, 2004

By Ross Seedsman

There are many models for how roof bolts behave, one of which is prevention of shear along bedding. The basis of this model is that a roof beam will not delaminate if bedding parallel shear can be prevented. A key point in such a model is that bedding discontinuities are present naturally in the roof and that mining induced stresses do not generate new surfaces. The presence of these discontinuities means that the rock mass must be modelled as a transversely isotropic material if continuum codes are used. A limit-equilibrium type design method for specifying roof bolts is being developed using voussoir beam and excess shear force concepts. The method incorporates much of what operators know intrinsically about roof reinforcement, and allows mining engineers to focus on the key uncertainty - the frequency and location of bedding surfaces in the immediate roof. Areas where more research is required are highlighted.

Jan 1, 2000

By Michael Alber

Coal resource extraction reaches higher depth of overburden and rockbursts as well as associated seismic events appear to become an additional problem to he addressed by ground control engineers. For example, German coal mines approach a depth of overburden of some 1400 m (4200 ft). Certain strata at those depths and associated high stresses may react upon resource extraction and subsequent deformation by violent release of strain energy, termed rodcbursts. Rock mechanics tests on numerous rock types have been conducted and three types of brittle rock behavior were classified. This paper describes different types of rock behavior in uniaxial compression and discusses a possible classification of rock with respect to their likelihood of violent response upon loading.

Jan 1, 2004

By S. P. Singh

Destress blasting is commonly used in the mines to minimize the occurrence of rockbursts. The fracturing created by destressing in the vicinity of the face reduces the stress concentration by pushing the zone of high stress deeper into the rock mass. But the destressing practice by blasting may be devastating near the faults or other sensitive high stress zones. To avoid severe rockbursts in such situations, the application of chemical destressing has been proposed in this paper. A laboratory investigation was conducted on the rocks in the Sudbury basin to examine the change in the material properties with an aim of assessing the feasibility of destressing by chemical means. The favourable change observed in the rock properties led to the suggestion that the injection of surfactants in boreholes would enhance fracture propagation similar to what is currently done by blasting but in a safer, inexpensive and non-violent manner. The current destressing practices in Ontario mines have also been reviewed in this paper.

Jan 1, 1987

By H. Gene Wilson

Mobile Roof Supports (MRS) look similar to a longwall shield on crawler tracks. The MRS units offer a safe, productive method of extracting the 40% to 60% product left normally unrecovered in room and pillar mining. The units feature radio control, self-contained power units, crawler track drive, and a 600 ton yield. Cribbing and setting posts in retreat mining has been a necessary burden to production. The MRS reduces this burden. Long blocks of coal can be developed to further reduce move and tram time, thus increasing production. The MRS units have successful safety records. The workers are removed from the immediate fall area, and we feel back injuries have been reduced by the workers not setting posts. While MRS units have been damaged in falls, the other capital equipment has been unharmed. The MRS product line has undergone normal product improvement and evolution. Product evolution is seen in our development of machines for particular mine requirements. Through the continuing development of the MRS, Fletcher presents the coal industry with a safe, productive method of retreat mining with potential to develop new mining methods.

Jan 1, 1990

By David H. Y. Tang

The reinforcement mechanism of suspension effect is analyzed based on beam-column theory. The equations of the maximum bending stress, deflection and transferred bolt load for the bolted roof strata are derived. In the analysis, the bolt load is assumed to be point load and the horizontal stress is uniformly applied to each stratum. The reinforcement mechanism of friction effect is also analyzed. The major function of roof bolting in this case is to create the friction¬al resistance by tensioning the roof bolts, thereby the individual thin strata are "welded" into one single thick stratum. Based on the results, equal spacing of roof bolts is used in the suspension effect while for friction effect, the bolts should be spaced based on equal shear force concept. The design nomographs for the proper bolting pattern and bolt ten¬sion of mechanical roof bolting systems are presented for practical applications.

Jan 1, 1984

In this paper, the plastic increment theory was applied in a 2-D finite element model, and a generalized Von Mises yielding criterion adopted to simulate the progressive failure of coal pillars. Extensive underground monitoring was conducted and the data compared with the computer model, yielding promising results. Three different longwall entry layouts, including a stable (s-s) pillar system, a yield-stable-yield (y-s-y) pillar system and a yield (y-y) pillar system, were investigated using the model developed. The yield-stable-yield system was considered to be the best of the designs studied in the case. A comprehensive parametric analysis was also performed. The triaxial factor and Poisson's ratio were found to be the most important material parameters affecting pillar yielding.

Jan 1, 1988

By Neil Styler

This paper presents an analysis of measurements of inter-burden de- formations above six longwall faces. An attempt is made to demonstrate some correlation between the movements at the various sites, and to examine their importance with respect to predicting caving height, disruption of overlying seams, and disruption of aquifers. This analysis demonstrates some significant differences between predicted surface subsidence, and inter-burden deformation. In addition it is shown that the caving height above a longwall face is equal to 8 to 12 times the extraction height, with a zone of fractured rock ex- tending to approximately 50 times the extraction height above the seam.

Jan 1, 1984

By Stanley J. Michalek

Good planning is critical to operating a safe and efficient mining operation. As the shallow coal scams become depleted, attention turns toward deeper mineable seams or remnant coal reserves. It is becoming more common to place a mine in a scam that is below or adjacent to existing mine workings. Significant research has been conducted regarding the ground control issues of multiple scam mining. However, safety aspects of the operation may not be fully considered. Safety issues include working below or adjacent to a flooded mine and controlling gas Communication between the active mine and the nearby mine. This paper will discuss the safety issues a mine operator should consider when working under or adjacent to mines that may be flooded with water.

Jan 1, 2000