Search Documents

By William Kendall

"A tremendous amount of research, analysis, and engineering time is used to design a proper roof support system including the type, length, and location of the roof bolts. Unfortunately, since the roof bolts are being installed under unsupported roof, the exact location for the bolt holes cannot easily be determined and then marked onto the roof. The actual location where the roof bolts are installed is typically left to visual estimates by the operator. This frequently results in either (1) the operator overestimating the space between roof bolts and installing more bolts than required, thereby increasing cost and reducing efficiency; or (2) the operator underestimating the space between roof bolts and installing fewer bolts than required, thereby reducing safety, leading to potential roof failure or possible violations.A patented laser light grid system has been developed by J .H. Fletcher and Monitech, a South African Company, to aid in proper machine positioning in the heading and proper bolt spacing. The system can also show when an entry is over width, requiring additional roof support. The system is relatively simple and inexpensive. The concept is applicable across the full range of roof bolters from low to high seams and from single boom to multiple boom bolters. The system can be configured to meet most bolting patterns.The system consists of several very small 1 milliwatt, class 2, line type lasers that project a line onto the roof. The actual laser is 27mm in diameter x 47mm long (1"" x 1.8""). In South Africa it is approved as intrinsically safe and is mounted inside a 50mm diameter x 64mm long (2""x 2.5"") protective housing. In the USA, we are seeking an X/P approval and the laser will be mounted in a headlight enclosure 110mm diameter x 125mm long (4.3"" x 5""). Fifteen of the systems have been installed in South African coal mines with good results.The system has aided the mines in meeting the bolt spacing tolerance used in the Republic of South Africa, which is typically 15% of the nominal bolt spacing or 7 in for 4-ft bolt spacing. Fletcher has submitted the system to MSHA for approval in the US."

Jan 1, 2016

By Rajendra Singh

In India, pillar mining is contributing more than 90% of underground production which involves extraction of a part of coal from bords with pillars around as natural support in the development stage. #Liquidation of these pillars with splitting and stooking, broken nature of face during mining under complex geomining factors like massive roof, varying treatment of goaf and over or underlying workings result in high stresses and deformation in and around the neighbouring piilars, causing operational problem and hazards to mine safety. This paper suminarises the results of three case studies of depillaring under shallow depth with or without stowing. Assessment of nature and amount of mining induced stresses and deformation was done under these conditions, by insitu instrumentation and observation at three depillaring panels of Girmint. Samla and Lachhipur collieries of ECC at 54, 90 and 110 m depth cover respectively. The value of induced stresses and associated deformations was comparatively low in well caved and stowed waves, whereas for massive roof the roof fall followed overriding of pillars and stooks, with very high value of induced stresses and deformaton in absence of stowing. The stress in the centre and outer edges of the pillars changed with respect to depillaring face advance or splitting of pillars. The caving panel of Girmint colliery under weak coal measure formation, showed maximum induced stress in the pillar at 4 m distance from the face which was 1.2 times (16.6 kg/sq.cm) the preminlng stress of the area. The main roof fall over partially stowed goaf of Lachhipur colliery under massive roof strata caused overriding of pillar after crushing 39 stooks of 7.5 x 7.5 sq.m in rythmic sequence with development of 133lsq.cm maximum induced stress. Well stowed Waf of the same panel reduced this value of abutment stress to 2.3 times (65 kg/sq.cm.) body stress after 40 m further advance of the face from the crushed zone. The depillaring at Samla colliery even under massive roof strata induced low stress, equal to 0.8 times field stress only under the same condition with stowed goaf. The studies revealed the effectiveness of stowing in the goaf over loading of pillars and stooks.

Jan 1, 1990

By Pier Paolo Manca

The investigated area lies close to a large town and covers an area of about lkm2. The mine was worked at depths ranging from 5 to 100 meters but mining operations actually ceased some 50 years ago. There are seven coal seams, each one to two meters thick, overlain by sedimentary rocks in a strongly faulted area. Different kinds of subsidence have occurred, crown holes, shallow depressions and hummocky ground. The results of rock mechanical characterisation (RMR method) in the area have been used to define three different types of numerical model (FLAC 2D). A large numbers of simulations has been performed to solve three different problems at three different scales: to determine the, mechanical properties of the roof rock and overburden involved in the subsidence process, to assess the crown hole subsidence potential and to define the properties of the beam foundations.

Jan 1, 1999

By Wei Yin, Yu Wu, Xiexing Miao

"For engineering problems of “three under” coal (coal trapped under buildings, waters-bodies and railways) exploitation, environment protection and gangue separation from raw coal underground exist in Tangshan Coal Colliery. By analyzing concrete technical problems, a technical approach of closed cycle “coal mining-gangue washing-backfilling-coal mining”, i.e. integration of coal mining, gangue separation and solid backfilling, is put forward with key technologies including gangue transportation with great depth, gangue separation from raw coal underground and integration of coal mining and backfilling. Based on the specific geological conditions of Tangshan Coal Colliery, 591m vertical feeding transportation system with great depth is designed; meanwhile, for efficient gangue transportation, ancillary wear-resisting pipe size and buffer equipment are optimized. Underground gangue separation system is created to be joined with the existing production system and backfilling system; besides, as per separation characteristics of coal and gangue, buddle jig is adopted for gangue roughing of raw coal underground. By cooperation of backfilling hydraulic support and other key equipment, the designed stope backfilling system completely realizes integration of coal mining and backfilling. Engineering practice shows that, through the research and implementation of the above key technologies, integration of coal exploitation, gangue separation and solid backfilling is successfully implemented in Tangshan Coal Colliery; moreover, it completely solves the three major engineering problems and realizes waste disposal, underground washing and separation, and ground surface subsidence control.INTRODUCTIONSo far, “three under” coal (coal trapped under buildings, watersbodies and railways) and key state-owned coal resources trapped under villages in China have reached 13.7 billion t and 5.22 billion t, respectively. With the development of coal enterprises, China currently has more than 1,600 gangue dumps (Miao et al., 2010a) with accumulated stack amount of 4.5 billion t, occupying a land area of 150,000 km2; moreover, surface subsidence caused by mining activities has damaged the environments of industry, agriculture, transportation and living, while new environmental pollution sources formed by coal related industries also result in damage to ecological environment (Huang et al., 2011a). On the one hand, due to large scale coal mining, some coal collieries suffering from resource exhaustion are faced with survival problems; on the other hand, coal mining has caused and been faced with increasingly prominent environmental problems, such as “three under” coal exploitation, waste disposal and ground surface subsidence control (Miao et al., 2010b; Zhang et al., 2009)."

Jan 1, 2015

By Thomas Barczak

Hydraulic cylinders are used in several roof support systems, such as longwall shields and mobile roof supports, to provide critical ground control Many state-of-the-art hydraulic support system operate at pressures as high as 7,000 psi to provide the necessary support capacities Pressure in the upper stages of multi-stage cylinders can be intensified by a factor of 2 or 3 providing pressures of 20,000 psi or greater. A proper understanding of the operation of these high pressure systems is necessary to safely maintain and repair these support systems. Likewise, the performmce characteristics need to be fully understood to evaluate the impact of design parameters on the capability of the support to maintain effective ground control This paper examines the basic operating principles of state-of-the- art hydraulic cylinders and discusses relative issues pertaining to. (1) setting loads, (2) support stiffness, (3) yielding behavior, (4) errors in assessing support loading, and (5) hydraulic failure mechanisms and how to detect them

Jan 1, 1998

By Dennis R. Dolinar

The U.S. Bureau of Mines has modeled yield pillars to determine the effects of reinforcement techniques on pillar performance. Model pillars with width-to-height (w/h) ratios ranging from one to four were reinforced using advanced lateral support systems. To evaluate reinforcement and pillar performance, the model pillars were strained up to 18.6 pct in compression. The results show that the reinforcement had a significant effect on the postfailure characteristics of the pillar but had only a small effect on it's maximum failure strength. Pillar residual strengths increased up to 10 times, while the energy capacity increased by a factor of three depending on the reinforcement method. At maximum deformation, the residual strengths of several types of reinforced specimens exceeded the maximum compressive strength up to 2.5 times and resulted in an increasing positive postfailure stiffness. Test results, data analysis, and application of the results to underground mining are discussed.

Jan 1, 1993

By S. M. Hsiung

A model (support selection model) for the selection of suitable types of powered supports under various geological conditions is proposed. This model is developed by evaluating the support, performance under different roof conditions at longwall faces in terms of five controlling parameters: (1) roof Falls, (2) front abutment pressure, (3) Face convergences, (4) gob materials entering into working area, and (5) roof caving line. This model suggests that more than one type of powered support. may be used under the same roof condition and the best selection should he based on the magnitude of suitability index of each support- type. The development and application of suitability index arcs discussed. Fourteen panels in seven coal seams are discussed in the paper to illustrate the applicability and effectiveness of this model. A roof classification system at longwall faces developed specifically for the construction of the selection model is also discussed. A simple example fur determining roof classification index is given.

Jan 1, 1988

By Joseph A. Cybulski

In response to the mining of reserves with increasingly adverse round conditions and the roof support recommendations of current rock mechanics theories, roof support systems have continued to improve. A few of these newer bolting systems. while giving improved performance, require a new method to check bolt installation. Previous1 , a torque wrench had been the sole means to check the installed torque of a roof bolt. However, due to the characteristics of soma of the newer bolting systems which can prevent a reliable manual torque check and a recent change in the federal roof control regulations, an alternative method to a manual torque check is gaining acceptance. This alternative method improves monitoring the hydraulic pressure of the roof bolting machine torque circuit and provides a safe, reliable and quick wav to check bolt installation in those instance when an accurate manual torque check cannot be made.

Jan 1, 1990

By Dezhong Kong, Jaichen Wang, Shengli Yang

"The stability control of longwall coal face is the key technology of large-cutting-height mining method. Therefore, a systematic study of the factors that affect coal face stability and its control technology is required in the development of large-cutting-height mining method in China. After the practical field observation and years of study, it was found that the more than 95% of failure in coal face are shear failure. The shear failure analysis model of coal face has been established, that can perform systematic study among factors such as mining height, coal mass strength, roof load, support resistance, and face flipper protecting plate horizontal force. Meanwhile, sensitivity analysis of factors influencing coal face stability showed that improving support capacity, cohesion of coal mass and decreasing roof load of coal face are the key to improve coal face stability. Numerical simulation of the factors affecting coal face stability has been performed using UDEC software and the results are consistent with the theoretical analysis. The coal face reinforcement technology of largecutting- height mining method using the grouting combined with coir rope is presented. Laboratory tests have been carried out to verify its reinforcement effect and practical application has been implemented in several coal mines with good results. It has now become the main technology to reduce longwall coal face failure of large-cutting-height mining method.INTRODUCTIONLarge-cutting-height mining method of more than 3.5m mining height, is one of the main methods for thick-seam mining in China. Currently, the largest mining height is 7.3m and the support capacity is 1,800mt. Shendong and Jincheng mining area have the best use of large-cutting-height mining technology (Wang, 2009). Generally, the mining height ranges from 6.5m to 7m and the support capacity ranges from 1,000mt to 2,000mt, annual output of the panel is between 10 and 12 million tons and the highest are 15 million tons. The main goal of large-cutting-height mining technology is to achieve high yield and high efficiency by increasing the advancing speed of longwall face (Yuan, 2011- 2012). However, in certain geologic conditions, rib spalling and roof falls in the unsupported area often occur. Because of the large tonnage of large-cutting-height mining equipment, once the rib spalling and roof falls cause the equipment to be out of alignment, the face advancing speed could be affected seriously that in turn affects the output (Yang, 2012). Therefore, studying the failure mechanism and control technique of coal face in large-cuttingheight mining method is of great significance."

Jan 1, 2015

By Collin L. Stewart

A summary of the results of a limited subsidence monitoring program at Cyprus Amax Coal Company's Shoshone Mine No. 1 in the Hanna Basin of south central Wyoming is presented. The monitoring program was designed to meet regulatory requirements for confirmation of subsidence predictions made in the mining permit. The longwall panels were 380 ft to 600-ft wide. Mining heights varied from 11 ft to 13.5 ft. Gate road development included three-entry and two-entry head and tail gates. Overburden depth varied from 150 to 945 ft. The coal seam and overburden dip at approximately 11 degrees. The overburden is very low to low strength mudstone and carbonaceous shale with low to moderate strength, silty sandstone interbeds. Panel W/h ratios varied from subcritical to supercritical. Smax was 0.9 of the mining height. The subsidence ratio was about 0.6 for subcritical width. The draw angle on the up-dip side averaged 20 deg. The draw angle on the down-dip side averaged 12 deg.

Jan 1, 1995

At any given lime, the tidal force subjects massive regions to a spatially uniform load. The deformation of any large structure due to these forces is proportional to the elastic properties of the structure. In this aspect, the tidal force applies a load in a manner similar to that of a large-scale testing machine. Any anomalies in the measured tidal response must reflect alterations in the average elastic response of the massive structure. In the present work, tidal tilt measurements obtained in the wall of a large dam are used to infer changes in the response of the dam to applied loads. In particular, it is found that the dam response has changed by approximately 13 percent, on average, for two monitoring periods separated by 5 years. It is possible that these changes were produced by the different volumes of water in the dam for the monitoring periods. The tidal measurement technique can also be applied to monitor changes in the average structural response of large underground and surface masses relevant to coal and metal mines.

Jan 1, 1992

Roof conditions at Southern Colliery, the second Iongwall mine to be established at German Creek, were found to be much stronger and more massive than at the earlier longwall mine on the lease. Investigations were made to ascertain the level of face support required for longwall extraction under the changed geological conditions. Geotechnical information was provided from drillholes and highwall exposures. Downhole geophysical logs, notably the sonic velocity log, were used to obtain a distribution of the major lithological units over the mine area. A representative type section of the strata and geomechanical properties was compiled to form the basis for numerical modelling. Two-dimensional finite element methods were used to predict strata movements and chock loads under cantilevered roof conditions. The model incorporated a 6.3 m thick roof beam either bonded or detached, with either a 2 m or 5 m overhang. The solid rib, immediate roof, chock support and goaf were modelled as distinct parts, in addition a front abutment stress profile, derived from three-dimensional displacement-discontinuity analysis, was superimposed on the model.

Jan 1, 1992

By Thomas M. Barczak

Wood cribs have been the dominant form of supplemental support in coal mining for many years. Recently, there has been a renewed interest in prop supports as a replacement for wood cribbing due to the increasing cost of mine timber and engineering advancements in prop design to improve their stability and yield capability. Prop supports generally consume less material, can be installed in less time with less labor, and provide less restriction to mine ventilation than wood crib supports. Several prop supports are now available or under development'. These include: (1) Strata Products Propsetter? Support System; (2) Heintzmann ACS and Super Prop; (3) MBK-Hydraulik MEGA prop; (4) Advanced Mining Technology Inc. (AMTI) BTS Mortar prop; (5) Dywidag Coal Post; (6) Western Support Systems YIPPI support; and (7) "The Can" support by Burrell Mining Products. A comparison of the performance and cost of these support systems to wood cribs is made to provide mine operators with information needed to assess their application potential. Examples of current underground installations are discussed. Included in this assessment are full scale tests of these supports conducted in the U.S. Bureau of Mines' Mine Roof Simulator.

Jan 1, 1995

By Michael Kelly

Current research in longwall mining in CSIRO Exploration & Mining is focused within five major projects and several minor projects. The major projects are: 1 3D Aspects of Longwall Geomechanics. This was reported to the conference last year and a final report will be available by mid-2001. 2 Mine Gas Control. This just completed project centred on Dartbrook Colliery which has a longwall gas make of more than 8 cubic metres per second. 3 Rapid Roadway Development This includes the construction of an autonomous conveying and bolting module (ACBM) that sits between the miner and haulage system. 4 Top Coal Caving In conjunction with the YanKuang group in China, CSIRO and the University of NSW are conducting a prefeasibility study of the Top Coal Caving method in Australian conditions. 5 Longwall Automation. In partnership with the Cooperative Research Centre for Mining Technology and Equipment (CMTE), the CSIRO has conducted a scoping study on this issue and will commence an initial three-year demonstration project in July this year. This paper describes these protects in more detail with particular focus on the last three in the above list.

Jan 1, 2001

By W. Mark Hart

The current Automatic Data Acquisition system developed by some support manufacturers make it possible to monitor and record changes in leg pressure, DA RAM stroke in every shield and shearer position at any moment during mining operation. But how can these massive data (more than 1 MB for every 3 hrs for the current scanning option) be effectively used for improving production and maintenance management as well as providing better roof control at a longwall face? The research currently conducted jointly by WWU and Cyprus Amax Minerals at Emerald Mine and Twentymile Mine attempts to answer this question and make the data, especially leg pressure, more meaningful. A computer software package has been being developed to (1) determine mining cycles, cycle time, face advance rate, production rates, machinery delays, and production delays for each shift; (2) identify defective sensors, check valves, yield valves, by-passing leg and DA RAM cylinders, and other hydraulic and electrical abnormalities; (3) determine the roof weighting period; (4) evaluate the performance of the current shield support design - demand relationships; and (5) predict and overcome ensuing encroaching problems and roof conditions ahead of the face.

Jan 1, 1994

By Christopher Mark

Mines with exceptionally low-strength roof (UCS <3,500 psi and CMRR <40) are much more likely to struggle with roof falls than other mines. Weak-roof is a particular problem for many room and pillar mines in the Midwestern and Northern Appalachian coal basins. Traditional roof support techniques are often not up to the challenge at these operations. This paper focuses on two mines, one operating in the Upper Freeport seam and the other in the Herrin No. 6 seam. Together, the two mines had more than 300 roof falls during a recent 5 year period. Each has experimented with a variety of roof bolt types and lengths, and with different supplemental supports. Detailed statistical analysis was conducted to determine which support combinations have proven to be most effective. Geology, horizontal stress, and time are also important at both mines. Successful control techniques have included; ? Identifying particularly troublesome lithologic roof units; ? Installing longer and stronger roof bolts; ? Installing supplemental support in intersections, and; ? Limiting the duration that a panel remains open. The lessons learned from these mines, and others like them, could help improve ground control safety for the entire U.S. mining industry.

Jan 1, 2004

By Christopher Mark

Preventing pillar line squeezes, massive pillar collapses, and coal pillar bumps is critical to the safe and efficient recovery of coal during retreat mining operations. To help prevent these problems, the U.S. Bureau of Mines has developed the Analysis of Retreat Mining Pillar Stability (ARMPS) computer program. ARMPS calculates stability factors (SF) based on estimates of the loads applied to, and the load-bearing capacities of, pillars during retreat mining operations. The program can accommodate various retreat mining scenarios including angled crosscuts, varied entry spacings, barrier pillars between the active section and old (side) gobs, and slab cuts in the barriers on retreat. It also features a pillar strength formula that considers the greater strength of rectangular pillars. The program may be used to evaluate bleeder entry designs as well as active workings. A data base of 130 pillar retreat case histories has been collected across the United States to verify the program. It was found that satisfactory conditions were very rare when the ARMPS SF was less than 0.75. Conversely, very few unsatisfactory designs were found where the ARMPS SF was greater than 1.5.

Jan 1, 1995

By Bruce W. Jack

An extensive underground roof-monitoring program was conducted in order to determine the roof strata behavior under various conditions. In total 29 sites at 5 different collieries were monitored using the sonic probe extensometer. Results showed that, in drill and blast sections, there are often pre-existing openings in the roof prior to the installation of the support. An estimated 42 per cent of the total roof displacement monitored in drill and blast sections took place prior to the installation of support. A comparison between roadways and intersections indicated that, for a 40 per cent increase in the span, taken across the diagonal of art intersection, relative to the roadway width, the magnitude of the displacement in the roof increased by a factor of 3. Total displacements measured were relatively small, only 2 reaching double figures of 12 mm. The remainder were all less than 7 mm. The results also showed no evidence of a substantial increase in the height of the bed separated, potentially unstable roof strata, as is the case in the high horizontal stress-driven beam-buckling mechanism experienced in for instance some Australian coal nines. Therefore, it was concluded that, in South African collieries, the effects of horizontal stresses is generally relatively small compared to overseas collieries.

Jan 1, 2000

By Paul L. Tyrna

The Fola Coal Co., LLC No 2 surface mine, located in Nicholas and Clay Counties, WV, exploits up to nine coal seams by contour, highwall, and mountain top removal mining methods. After encountering faults, areas of highly fractured coal, and subsidence failures. the mine requested a lineament analysis from the Mine Safety & Health Administration&apos;s (Pittsburgh Safety and Health Technology Center) Roof Control Division. The 31 km2 study area was viewed on a LANDSAT-5 band 4 (near infrared, 0.76-0.90 µm wavelength) satellite image with ERDAS Imagine 8.4 software. The software allows image examination under artificial sun azimuths and elevations, resulting in variable tonal characteristics. The study area image was viewed in 45° azimuthal increments from 000° to 315° at artificial sun angles of 10°, 30°, 50°, and 70°, yielding 32 separate images. The interpretation process developed by MSHA Roof Control personnel identified 16 northeast-striking and one northwest-striking lineament that intersected mine property. Faults and areas of roof instability corresponded well with lineaments identified in the study. Successful lineament identification prompted mine management to incorporate lineament analysis as a mine-planning tool for adjacent property, thereby identifying in advance areas that could adversely affect safety and production.

Jan 1, 2001

By Tim Ross

J. M. Huber Corporation&apos;s Quincey Mine. an underground limestone mine located near Quincy. Illinois, has operated successfully and safely for many years utilizing roof bolts on a very limited basis. Over the years, the mine had experienced several rool falls that did not result in injury to personnel. Nearly all of the roof falls were limited to the first 2 feet of the massive limestone roof. Investigation of the falls indicated the major contributing factor to these roof falls was a randomly occuring thin. horizontal clay layer in the immediate roof. Over time, separation would occur at the clay layer. causing the root to sag. and eventually causing the root to fail. J. M. Huber Corporation contracted with NSA Engineering. Inc. to assist in a study to determine the effectiveness of Ground Penetrating Radar (GPR ) for locating these potential root fall areas so that mitigating action could he taken prior to roof failure. Multiple tests were conducted in areas of known roof conditions. GPR accurately predicted the existence or absence of root separation up to 1.5 meters into the immediate roof for 100 % of the known lest site conditions. As a consequence of this successful studs, J. M. Huber Corporation has used GPR to evaluate roof conditions at both its Quince and Marble Hill Mines.

Jan 1, 2002