Search Documents

By C. I. Walker

"Understanding the influence of slurry particle size on wear is essential to maximising the life of centrifugal pumps operating in mineral processing plants and for hydrotransport duties. Particle size influences not only the wear rate but also the wear pattern in pumps. Complicating the situation is the different relative wear rate for different pump parts depending on particle size. A simple Slurry Wear Type (SWT) number based on particle size and size distribution is proposed as a means for categorising slurry pump wear patterns and optimising pump application and material selection. INTRODUCTION The wear of centrifugal slurry pumps in mineral processing and hydrotransport can be quite severe and is one of the major cost concerns of plant operators. Some typical worn slurry pump parts made from high chrome white iron are shown in Figure 1. Erosion wear rates of up to 2 mm/day are not uncommon [1].Centrifugal slurry pumps are required to handle solid-liquid mixtures with a very wide range of particles extending from sub-micron size clay through to 200mm and larger cobbles. Particle size distribution can also vary widely from uniform and narrow (such as graded sand) through to very broad (such as grinding circuit slurries). Slurry particles may also undergo size change due to attrition during the pumping process. The major wearing parts in a slurry pump are the impeller, side liners and casing liner. These are shown with reference to a Warman® MC centrifugal pump in Figure 2. While many particle properties (including size, shape, hardness, density and concentration) influence pump wear, this work will consider only the effect of particle size as it is the major determinant of wear characteristics. Particle size influences the wear pattern, material performance and relative component wear rate in centrifugal slurry pumps. SLURRY WEAR TYPE (SWT) BASED ON PARTICLE SIZE Soil and grain size classification systems abound. Many have different limits to the ranges for a particular classification, albeit not too"

Jan 1, 2018

By I. M. Stewart

In a proposed rulemaking regulating asbestos, nonasbestos varieties of Tremolite, Anthophyllite and Actinolite would be excluded from the regulations controlling permissible exposure to asbestos fibers. This proposed rulemaking is perceived as improving the scientific basis of the regulation of asbestos because it recognizes that there are no scientific data, either mineralogical or health related, which support the regulation of nonasbestos Tremoiite, Anthophyllite and Actinolite in the same manner as asbestos fibers. However, the proposed regulation, while representing a major advance in the treatment of AT A for regulatory purposes, does not provide an adequate analytical method for distinguishing between asbestos and nonasbestos particles, nor an adequate description of the regulated minerals. This paper addresses those topics, recommending that OSHA include an appropriate mineralogical definition, and implement a discriminate counting procedure to distinguish asbestos from nonasbestos particles.

Jan 1, 1992

By H. N. Frock

The use of low-angle forward light scattering for measurement of particle size distribution has been described previously.1 Laboratory instrumentation using this technology is used routinely in operating plants for quality control and production control.2,3 Extension of the technique to on-line process monitoring and control has also been undertaken in several important areas. This paper will discuss the application of MICROTRAC R systems to the monitoring of particle size in wet slurry processes and dry powder grinding circuits. Examples of existing installations will be given with emphasis on performance and on-line reliability.

Jan 1, 1979

By Y. T. M. Ocsa, V. O. Tenorio

This research is the result of a geotechnical study carried out in a natural slope in an Open Pit mine in Southern Peru, highlighting earthquakes as an important cause of instability within the case study presented. This leads to analyze the stability of a slope, according to the safety factor and thus consider a future construction in its environment according to the identified requirements. There are known disasters at national and international level that involve human lives because of the lack of analysis of slope stability conditions, which based on the results will allow to control and to take adequate corrective measures. These mass movements are classified whether they are soils or rocks, considering the mechanism and type of rupture, as well as the presence of water, the speed and magnitude of the movement. The movement problems are due to factors of inherent nature and constitute a reason to perform a calculation study to analyze and estimate the safety factor of each of the evaluated cases

Mar 2, 2022

By S. Bastola

Over 80% of roof falls in Illinois coal mines occur at intersections. Regular intersection geometries with sharp corners have been typically analyzed in literature. This study has analyzed stress distribution around typical field 4-way intersection geometry and compared it with similar data for regular four-way intersection geometry. These analyses were performed using 3-D numerical analyses for a typical lithology associated with No 6 coal seam in southern Illinois. Linear elastic and non-linear analyses, using Hoek-Brown failure criteria for different lithological units, were performed. The 3-D models incorporated bedding planes and pre-mining horizontal stresses. Effect of diagonal widths of the intersection and pre-mining horizontal stresses were examined due to their influence on stability. In addition to stress distribution, contours of safety factors, and displacement analyses were performed to assess stability of intersections.

Feb 27, 2013

By G. M. Wenberg

Bacterial leaching of copper and uranium is practiced in environments containing available sulfur and iron and having a strong acidic reaction. However, many mineral deposits do not have these conditions; the chalcocite and native copper ores in Michigan's Upper Peninsula are examples. Bacterial and fungal populations were observed in samples taken from the White Pine Copper Company tailing pond and mine, and isolates were prepared of the dominant species. The isolates were then screened for solubilization of copper from tailing, ore, and concentrate during incuba¬tion in a carbon and nitrogen supplying medium. Certain Penicillium fungi solubilized significant amounts of copper under neutral to slightly acidic conditions. Leaching apparently was accomplished by release into the medium of metabolites which chelated with the copper.- The process was found to be highly dependent upon the medium and the concentration of copper in the source material. The paper describes sampling and screening techniques, presents the results of experimentation to standardize procedures and maximize the yield of copper, and discusses the nature of the leaching process. This preliminary research reveals a biological process which may find use in mineral extractions but whether it can be applied economically remains to be determined.

Jan 1, 1969

By Philip Lindstrom

Retreat mining, using yielding steel friction props, over a seven-year period has been successful at a uranium mine operated by Hecla Mining Company in southeast Utah. The support system allow good roof control, maximum profit, complete extraction, and good ventilation. Unusual subsidence observations were made in that some of the surface was raised rather than lowered, Longwall mining, commonly practiced in European coal mines, has a potential of broader application because of mechanization possibilities and better roof control and ventilation at greater depths.

Jan 1, 1964

By S. Lee, F. Campero

"Past heap leach design has evaluated hydrodynamic parameters based on a uniform particle size of heap material, but has ignored the equal importance of the instability of fine migration within heap stack in the beginning stages of the irrigation process. The proposed probabilistic model evaluates internal fine erosion and segregation potential of well-graded crushed ores by considering the entire particle size distribution shape and site compaction degree. Using this model, unsaturated flow model parameters were successfully evaluated based on synthesized soil-water characteristic curve (SWCC). Additionally, one-dimensional unsaturated transient flow modeling with Hydrus 1D® showed that the different recovery efficiencies of heap material under unsaturated flow patterns depending on the particle size distribution and compaction degree of heap material. Agglomeration preprocess employed by most heap leach sites can reduce the potential of fine erosion within heap material significantly, but internal stability of crushed ores and hydrodynamic-based analysis of heap material’s pore structure is equally important in the prescreening stage in order to improve efficiency of the heap leach and avoid a costly agglomeration process. INTRODUCTION Accurate estimation of heap leach recovery is a difficult task due to the variety of design parameters that need to be considered - such as geochemistry, hydro-dynamics, and geotechnical design aspects, most notably particle size distribution through the process of agglomeration. After agglomeration techniques were introduced to heap leach design, the influence of particle size distribution and compaction degree in enhanced heap leach recovery has been neglected. The main purpose of agglomeration is to prevent fine segregation and internal erosion during and after heap stacking for well graded crushed ores, which will eventually diminish heap reach recovery. Recent studies show that agglomerated heap materials that had been consolidated at 10 meters below heap surface can release the fines after contact time with lixiviant to the compacted heap material and produce poor drainage performance (Milczarek et al, 2013). It must be noted that engineers and practitioners should investigate feasibility of agglomeration benefit prior to heap leach design because the agglomeration process can incur up to 20 or 30% of project costs. Internal stability of stacked heap material is mainly governed by the particle size distribution of crushed ores. Depending on this stability, segregation and internal erosion of fines can be mitigated by the application of moderate compaction effort during heap construction. Investigation of segregation and internal erosion potential therefore takes precedence for well graded crushed ore since reaction time and contact area with lixivant are greater in finer ores."

Jan 1, 2016

By Raymond Mancha

"Conventional" coal dryers really do not exist. What we really mean to say is that there are many and varied kinds of coal dryers -- and the "air handling problem" is really the only portion of it which has been approached for solution by conventional methods. It now appears that these conventional methods need supplementing by some new, relatively unconventional apparatus. In order to approach this matter with mutual understanding, here is a quick survey of the coal drying art. Figure #1 shows a McNally Pittsburgh Pulso Dryer, In the McNally Pulso Dryer, the coal is fed-onto the screen by a rotary feeder assuring even distribution of the coal. As the coal travels forward due to the action of the screen, it is subjected to a controlled pulsating flow of hot gases. T ese originate below the deck and are directed up through the moving bed of coal. Fines sifting through the deck are dried in the hopper below the screen as they fall through the hot gases to an evacuation screw. The coal remaining on the screen is dried to the desired degree when it reaches the discharge end. At this point, it is directed down into the evacuation screw to combine with the fines, or it may be discharged as a separate product. As the coal travel down the screen, it is subjected to intermittent upward currents of hot gases. These first distend the bed allowing the gases to come into intimate contact with the coal particles for rapid and efficient heat transfer. Then, as the flow of gas is cut off, the bed settles and the extreme fines sift through the screen preventing their being carried away into the exhaust system.

Jan 1, 1958

By Igor Gonzales G.

Southern Peru Copper Corporation (SPCC) has recently completed the construction of copper leaching, solvent extraction, and electrowinning facilities at their Toquepala and Cuajone plants in Southern Peru. Much of the ore for these new operations is the result of the existing mining operations that have been in existence as early as 1959. At Toquepala, pre-conditioning and bacterial dump leaching of the sulfide ore that was too low in copper content to be processed through the copper concentrator began in 1987. The Cuajone heap leach operation is treating copper oxide ore that has been stockpiled since the Cuajone concentrator began operation in 1976. The pregnant leach solutions from the dump leaching at Toquepala and the permanent pad heap at Cuajone are combined into one plant feed solution. Adjacent to the large dumps at Toquepala, a solvent extraction and electrowinning facility has been constructed. The electrowinning facility has a planned annual production rate of35,000 metric tons per year Grade A cathode copper. Initial production of the cathode copper began in November 1995.

Jan 1, 1996

By Melvin A. Jennings

Even though the title of this paper is quite long, the ideas presented herein are very simple. In fact, it occurs to me to be somewhat humble about coming before such a distinguished group with such a simple presentation. However, the application of these ideas has proven useful in at least two copper flotation plants. The purpose in presenting this paper is to inspire some interest in the great stores of data chat the Mining Industry often accumulates without making any attempt at analysis. Unfortunately, many milling engineers rely rather heavily on percent recovery as a strict measure of a concentrator's relative performance. The fallacy of this reasoning is not difficult to see since, by definition, percent recovery is a function of feed assay, tails; and concentrate grade. If copper tailing is constant, and it very nearly is for a strictly sulfide copper ore, percent recovery must fluctuate almost directly to the feed assay. The point that I wish to make here is that it is very seldom justified to compare the percent recovery figure from one period of time to another without considering the difference in feed assay. The problem of comparing results is even further complicated when the ores are of mixed oxide and sulfide mineralogy.

Jan 1, 1978

By Judson G. Brown

In the May, 1969 issue of Mining Engineering the Editorial Director, John V. Beall, described the Japanese Onahama Copper Smelter and Refinery as follows: "On the shore of the Pacific, 120 miles north of Tokyo, is the world's most modern copper smelter and refinery.? One of the improvements that has been made at the Onahama Refinery is the quality of the electrolyte in the copper refinery electrolytic cells. This has been accomplished by reducing the concentration of slimes in the cells between the electrodes. In a December 19, 1966 review in Chemical Engineering magazine reference was made to some tests in Sweden as follows: ?However, at 1,000 amps/sq.M., satisfactory cathodes could be prepared, provided electrolyte flow past the anode and cathode was at least 3 to 4 meters per minute, and the slime content was not allowed to exceed 20 to 30 mg. per liter. By dropping the current to 500 amps with the same electrolyte velocity, the slime content could grow to 50 mg. per liter (50 ppm) without causing occlusion at the cathode." From this data it appears that the production capacity of copper refining electrolytic cells can be significantly increased. In order to do this the concentration of suspended contaminating slimes in the electrolyte solution is reduced by filtration. The electrolyte in-between the active electrodes must be purged with higher velocities to maintain a high concentration of the desirable copper ion in the liquid film adjacent to the cathode and the sulfate ion in the liquid film at the anode. This higher velocity also carries away from the cathode the undesirable impurities released from the anode as they are released into the electrolyte as filterable solids.

Jan 1, 1970

By Marcel Laflamme, Sebastián Ibarra‑Gutiérrez

Improvement on controlling the stope limits has enabled the assessment of technical performance in several underground mining operations. Technical performance, integrated to stope geotechnical and geomorphological parameters, constitutes the basis which guides mining engineers in the Mineral Reserves Estimation process. Moreover, there are established definitions to report this information in Canada, incorporated in NI 43–101, which stipulates that “A Mineral Reserve includes diluting materials and allowances for losses that may occur when the material is mined” [1]. However, some loopholes have been identified regarding practical standards followed to specify the way to include and report ore losses when the lost material was blasted and must be left behind unrecovered inside the stope. In fact, general efforts to estimate and quantify the negative effects of operational ore losses only consider under-break ore loss. However, mining engineers frequently confront situations requesting the anticipated closure of a stope. Therefore, reconciliation process should reflect the amount of unrecovered Mineral Reserve. This work presents a discussion of possible practices to integrate adequately operational ore losses consisting of blasted but not recovered material and focuses on how different approaches regarding the material constitution could severely affect the stope technical performance interpretation.

Aug 9, 2021

By Diana Diaz, Rakshith Shetty, Vitaly Proschenko, Mike Mooney

Cohesive clay soil poses a significant risk to earth pressure balance tunnel boring machines (EPBM) due to unstable face pressure, clogging potential, high cutterhead torque, poor muck flow, low advance rate, etc. This paper details the performance measures desired when EPBM tunneling in clay soil, and the scientifically-supported conditioning methods to transform in-situ clay to a muck with such characteristics, giving particular attention to ground conditions. The paper then examines TBM data from multiple clay soil projects in the context of these performance measures to demonstrate the influence of cohesive soil conditioning on EPBM performance.

Jun 13, 2023

By William D. Meakins

INTRODUCTION Today, auxiliary fans, or boosters as they are sometimes called, are commonly used underground to provide ventilation for safe working conditions for personnel. Fans are installed in many ways and for many purposes; however, their use falls into three main categories depending upon the application. Auxiliary Face Ventilation For Coal Mines Usually the application of auxiliary fans underground in coal mines presents problems not normally encountered in other types of mining. Two of the major problems deal with liberation of methane at the coal face and the production of coal dust in the mining process. For these conditions it is necessary to use permissible (explosion-proof) type of equipment. As a result, these fans are discussed in a category by themselves. Auxiliary Fans For Tunnel and Drift Ventilation Tunnels and drifts present unique ventilation requirements. For instance, tunnels and drifts can be developed for considerable distances into virgin territory. Since they are generally dead-ended, the only way to obtain ventilation at the face is to use ventilation pipe to establish one leg of a ventilation circuit. The ventilation of tunnels and drifts therefore falls into another natural category. Other Uses of Auxiliary Fans For Mining Purposes Fans can be applied to mining applications in many ways other than those discussed under the other two categories. For example, many times auxiliary fans can do a much more practical job of proper air control and distribution that can be achieved with any other mechanical means; therefore, these other uses are discussed as a special category. AUXILIARY FACE VENTILATION FOR COAL MINES After 1936, federal and state coal mining laws prohibited the use of auxiliary underground fans in coal mines since such equipment had been widely misused. In certain cases, recirculation of face air had been allowed to occur thereby creating a serious potential explosive hazard by the possible buildup of excessive methane concentrations. By the late 1950s, mining machines with rapid face penetration were commonly being used in coal seams which liberated higher quantities of methane than in earlier years. As a consequence, in the late 1950s and early 1960s, the use of auxiliary face fans was again allowed under strict experimental conditions because conventional methods of face ventilation control without fans were becoming inadequate. Today, auxiliary face fans are widely used under strict federal and state control. Such auxiliary ventilation does not reduce the need for the amount of primary air from the main mine fans; however, it does help to distribute primary air more efficiently at the face. The present trend is toward an exhaust system of ventilation utilizing 406- to 610-mm (16- to 24-in.) diam tubing extending from the face to an outby auxiliary fan. Since the tubing is normally applied with negative pressure, spiral wire reinforced tubing has been replaced largely with metal and, more commonly, fiberglass tub¬ing. Additional auxiliary blower units are often used at the mouth of the room being developed, or installed on the miner or loader near the face, depending upon the amount of gas liberation present. Often one (or more) of the fan units is equipped with an integrally mounted hopper and feeder which automatically adds a continuously metered amount of rock dust to the exhaust air. The combination unit tends to make the mixture of discharge particles noncombustible and reduces to some extent the need for additional rock dusting of return airways. In this part of the chapter, typical auxiliary ventilation systems are described including curves and photograph of typical/applicable equipment. Reference will be made to "blowers" and "ex¬hausters." Both are fans and are basically the same units. They take on their name through the manner in which they are used. A blower usually has an inlet bell on the inlet side to help to obtain good air flow into the blades. An exhauster often has a discharge cone added to reduce the discharge loss. Any basic fan unit can be used either as a blower or an exhauster. Description of Auxiliary Ventilation Systems Several auxiliary ventilation systems and modifications of basic systems have evolved over recent years. Some of these systems are described and illustrated. System No. 1, an exhaust system for faces with comparatively low gas liberation, is shown in Fig. 1. Here

Jan 1, 1982

By C. L. Sarff

[Automation has become a word that means many things. To management it is the end of the rainbow; you push a button and all your problems are solved. To the working man it is a horrible monster that is taking his livelihood away. To the maintenance man it is a complex that overwhelms him when he thinks of trying to find the trouble when the machine is not operating, properly. Automation has been with us in the coal nines for many years. Long before my time you were using float switches on mine sumps to control the level of the water. That?s automation in the truest sense of the word, but we call it automatic and think nothing of it. If we use the word automatic instead of automation your mine electrician and mechanic will take hold of the problems in stride.]

Jan 1, 1962

By R. K. Zipf

Recent scientific studies by researchers at the National Institute for Occupational Safety and Health (NIOSH) and the U.S. Army Corps of Engineers (USACE) presented the worst-case explosion pressures that can develop if a methane-air mixture of a certain composition and dimension accumulates and ignites within a sealed area of a mine. The Mine Safety and Health Administration (MSHA) issued its final rule on sealing of abandoned areas which considers potential explosion pressures and the risk of achieving the necessary conditions. The new MSHA seals regulation has increased the pressure design criteria an order of magnitude beyond the old standard of 140 kPa (20 psi) to 800 kPa (120 psi). However, there still are major knowledge gaps pertaining to seals and sealed areas including: (1) the composition of the sealed area atmosphere and how it changes in time and space, (2) explosion pressures that might actually develop within sealed areas, (3) engineering procedures to follow when designing seals and seal installations, and (4) guidelines to manage the atmosphere within sealed areas with monitoring or inertization. NIOSH has initiated a seals research program with collaborators from Safety in Mines Testing and Research Station (SIMTARS) in Australia, West Virginia University (WVU), the Naval Research Laboratory (NRL), and USACE. Highlights of progress so far include: (1) construction of a gas explosion tube at Lake Lynn Laboratory for studying large methane-air explosions, (2) computer simulation of the fluid dynamics of high pressure methane-air explosions, (3) development of seal analysis methods considering construction materials, reinforcement and the seal foundation, and (4) development and testing of innovative seal designs that utilize inexpensive, readily-available rock rubble to resist high explosion pressures. NIOSH researchers aim to provide sound engineering guidelines to better address the new MSHA seal regulations. DISCLAIMER: The findings and conclusions in this report have not been formally disseminated by the National Institute for Occupational Safety and Health and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By Richard H. De Voto

The Pb-Zn-Ag deposits within the Lower and Middle Paleozoic strata of central Colorado (Leadville, Gilman, Aspen, and others) occur principally in Late Mississippian karst-solution features within dolomites and, to a lesser extent, limestones. Several un- conformities within the Devonian and Mississippian carbonate rocks and the subregional dolomitization of the Leadville (Mississippian) Formation that occurred during the Late Mississippian resulted from recurrent uplift of elements of the Ancestral Sawatch, Gore, and Front Range areas within central Colorado. Uplift of these areas also strongly influenced the details of the extensive karst topography that developed during the Late Mississippian. In particular, uplift of the Sawatch Range area caused paleovalleys from 300-600 ft deep to form on the karst landscape. The pattern of karst-solution caverns, sinkholes, cutters, channelways, and breccia-rubble zones was strongly controlled by incision of surface drainages and the strong northeast-trending Mississippian joint system. These subterranean karst-solution features and breccia-rubble soil [ ] zones are the primary controls of the location of the Pb-Zn-Ag ore deposits in these rocks. In the Leadville and Aspen districts, the deeply incised paleovalleys occur immediately adjacent to the principal areas of mineralization. Pennsylvanian deposition of a thick terrigenous and evaporite sequence occurred within central Colorado in response to actively subsiding extensional basins and adjacent high-relief uplift areas. Hot brines developed within the Pennsylvanian strata, migrated laterally to, and moved upward vertically along, basin- margin faults during continued Pennsylvanian subsidence and deposition. These metal-rich brines migrated into karst-solution features within the Lower and Middle Paleozoic dolomites and limestones, principally within the Leadville Formation, in basin- edge uplifted locales where the Pb-Zn-Ag minerals were precipitated. Field relationships, mineral assemblages and paragenesis, fluid-inclusion data, and isotope studies suggest that the metals and brines were derived within the Pennsylvanian sedimentary sequence and that the ore minerals were deposited under different temperatures and at different depths from deposit to deposit. Chemical reaction with the carbonate cave sediment and wallrock, cooling of fluid temperatures, and mixing with meteoric ground waters were the probable combined causes of mineral deposition in the karst-solution features. Late Cretaceous-Tertiary intrusive activity has subsequently modified some of the primary Pb-Zn-Ag deposits in local areas.

Jan 1, 2013

By N. A. Abdel-Khalek

Laboratory flotation tests were carried out on six Polish samples of different rank. Each coal sample was screened into 7 size fractions. The floatability of size -by- size for various size ranges for different samples was investigated as: well as the original samples. The results showed that in flotation of size -by -size, the intermediate size had the maximum floatability. The range of this intermediate sizes varied with the rank of the coal. Entrainment was shown to be an important mechanism to the recovery of fine particles in flotation of the original samples".

Jan 1, 1989

By Jon G. Baird

The suggestion of the use of measurements of trace amounts of mercury as a guide to the location of sulphide ore deposits was first made by the Russian, A. A. Saukov (1), in 1.946. Since Saukov's original work, many others have studied the abundance of mercury in nature, the association of mercury with sulphide ores and methods by which very minute quantities of mercury can be measured in air, soil, rocks, water and plants. The most abundant of the mercury bearing minerals is cinnabar (HgS). Native mercury is also found and sulpha-salts like tetrahedrite are known to have important mercury contents. Other sulphides of base metal deposits contain mercury in amounts ranging from parts per million to as much as one or two percent. (2) The mercury content of sulphide-free rocks is usually less than a few hundred parts per billion (1 ppb - 10-9), Soils usually contain less than 100 ppb and water less than 1 ppb of mercury. Normal atmospheric air contains about 1 nanogram (10-9 grams) of Hg per cubic metre although higher concentrations can be observed near mercury occurrences, sulphide deposits and volcanic exhalations.

Jan 1, 1973