Search Documents

By A. D. Paananen

With the demand for higher grade feed by the American steel industry and the depletion of the direct shipping ores from the Marquette Iron Range and elsewhere, there was a need to develop the low-grade orebodies. The large reserve of fine grained oxidized iron-formation at the Tilden Mine has been the object of research and development efforts to concentrate the iron oxides as far back as 1949. Preceding the present mining-concentration-pelletizing complex, about 6,500,000 long tons of direct shipping siliceous ore were shipped from the Tilden Mine. Following development of the concentrating and pelletizing flowsheets, engineering and construction was initiated to develop the mine and construct concentrating and pelletizing facilities to produce 4,000,000 LTPY of pellets from this low grade crude ore. Operations started in late 1974 with Algoma Steel, J&L Steel Corp., The Cleveland-Cliffs Iron Company, The Steel Company of Canada, Ltd., Wheeling-Pittsburgh Steel Corp., and Sharon Steel Corp. as participants. Cleveland-Cliffs operates and manages the operation. Due to the non-magnetic nature of the ore and the fine grinding required to liberate the iron oxide minerals, this crude ore was not amenable to concentration by conventional methods. The iron oxides of the Tilden orebody have a grain size of less than 25 microns and recovery of the finer, well-liberated iron oxides is essential. Conventional methods of des liming employing cyclones or thickeners were not feasible because of the excessive loss of iron oxides in the finer fractions.

Jan 1, 1978

By Werner Wenzel

Methods to increase the gas penetration through sinter layers. In the field of agglomeration, sintering has gained importance, specially in Europe; in Best-Europe this trend will continue till the year 1980, since it is quite probable that in the blast furnace burdens with 50-60 sinter, 10-20 % pellets and 20-25 % ore lumps will be employed. In order to meet this demand for sinter, new sinter bands with reaction areas between 300-400 m2 will be constructed. Chemical and physical phenomena during the Suction-Draught-sinter process. Iron ore sintering is generally considered as a burning process where the material contains 90-95 % ash i.e. non-combustible ingredients. Sintering represents a heterogeneous exothermic reaction in which the chemical phenomena as combustion, calcination, hydration, reduction and oxydation are superposed by physical phenomena. The physical phenomena are devided into material transport and simultaniously occurring heat transport processes. The velocity of these combined physico-chemical reactions i.e. the change in the reaction site per unit time determine the efficiency of the sinter process. The gas permeability as an important criterion of heat transport during the Suction-Draught sinter process.

Jan 1, 1971

By H. S. Puttanna

Bound water plays an important role in the processing and utilization of numerous materials and mineral processing systems. The fundamental nature of this near surface bound (vicinal) water is yet to be understood in its complete detail. The objective of this paper is to use dielectric measurements to characterize the bound water near hydrophobic and hydrophilic oxide surfaces. It is anticipated that a combination of dielectric property measurements and characteristic relaxation times will allow for more effective analysis of the interfacial water.

Jan 1, 1992

By C. W. Overton

The operations of Bethlehem Copper are situated in the south-central interior of British Colombia at an elevation of 4900 feet above sea level. Main road and rail transportation systems pass through Ashcroft in the Thompson Valley, which is 28 miles by road from the minesite. The operation was the first low-grade open-pit porphyry copper mine in British Colombia. The minerals are chiefly chalcopyrite and bornite, while the rock is principally feldspar and quartz. In the outer fringes of the orebodies sane pyrite is present. Average grade of mill feed is 0.55% copper.

Jan 1, 1973

By Zong-Xian Zhang, Charlie C. Li

It has been observed that the rock debris of a strain burst event are often in the mode of tensile fracture. Seismic waves could create tensile fractures in the material nearby reflecting surfaces, such as at the boundary of the fracture zone and the rock surface of an underground space. The fractured rock could be ejected to the space when the seismic waves are powerful enough. The average ejection velocity of the ejected rock is a measure of the magnitude of a burst event. The ejection velocity is directly associated with the released energy from the seismic waves and with the strain energy stored in the rock prior to the burst. In some cases, the seismic wave induced tensile fracture and the energy conversion occur in successive moments during bursting. In this paper, tensile fracture caused by seismic waves is investigated through an 1D model. The relationship of the average ejection velocity of the ejected rock in a rockburst event is analytically established with the energy of the seismic waves and the strain energy stored in the rock.

Apr 26, 2022

By A. E. Ketler

Optical smoke monitoring fills an important gap in ventilation and fire safety: namely monitoring of smoky, low temperature fires where little CO and heat are generated. Smoke monitoring also avoids the nuisance alarms due to diesel exhaust, battery chargers, blasting and welding. The smoke optical density (OD) fire alarm standard specified by MSHA presents an opportunity for improved safety. Experience of actual mine usage of the SmokeBoss*100 is reviewed, with particular regard to effectivity, maintenance and cost.

Jan 1, 1995

By Alejandro Prieto

Traditionally, Mexico has been a mining country. This industry has played a very important role in our country's development, creating jobs, integrating geographical regions - generally very remote from urban communities - and, an essential factor in our present day economy, generating an influx of foreign currency. The Fluorspar mining industry's development started in the 1920?s, but it was not until World War II that its exploitation became consistent and started growing. During the last few years, Mexico has become the world's leading producer, with an annual output of more than one million tons, which directly generates over 3,000 jobs. The actual proven reserves can guarantee fifty years of production at this same annual rate, and it is due to this fact that the producers have not increased their reserves. However, there is concrete information of the existence of several deposits, extending from the northern border to the gulf of Mexico, forming the "Fluorspar Belt? in Mexico.

Jan 1, 1986

By John R. Buzek

Thickeners are simply large tanks, usually circular in shape, which are designed to allow settling of solids and to operate with continuous overflow of clear water and underflow of thick pulp. The dimensions of the thickener are usually such that dewatering of very fine pulps may be accomplished while still 1 overflowing clear water. Some thickeners such as the Genter, Hardinge and Hydrotator types combine thickening with filtering2 while others such as the Dorr type are pure thickenersl,2,3. A schematic diagram of the traction type Dorr thickener is shown in Figure 1. This type is appropriate for tanks over 15 m (50 ft) in diameter. This tank employs a rotating raking mechanism which moves the settled material toward the central discharge. For this and other thickeners, it is common to have a shallow conical tank bottom in order to conform to the geometry of the raking mechanism, and it is often desirable to elevate the tank for ease of access to the product. When the tank does not rest on the ground, the forces resisted by the cone are large, and thick plates must be employed. The fabrication of these tanks requires temporary supports in order to erect the cone. A flat-bottomed tank could also be used because the settled material would soon form a hardened conical surface. However, because of the presence of large bending forces, even larger plate thicknesses are required than for the conical bottom. Significant cost savings often can be realized by the use of a scalloped-bottomed tank such as the one partially shown in Figure 2. The particular scalloped bottom discussed in this paper (and shown in the Figure) employs radial beams forming the outline of the cone-shaped bottom. These beams are supported directly by columns. Cone segments are hung between adjacent beams. The exact geometry of these segments depends upon the cone angle and radius, the number of radial beams, and their inclination. The geometry is chosen to satisfy certain clearance restraints and to utilize the material as efficiently as possible. The resulting thickness of these segments is significantly less than that of the

Jan 1, 1977

By QU Hong-lue, YANG Lin-han

Aiming at the subjective impact caused by subjective weighting method in the establishment of rockburst risk attribute identification and prediction model, the combined weighting method was introduced to eliminate the influence of unreasonable weight of each index. Eight discriminant indexes affecting the risk of rockburst were selected. Through the literature review, relevant rockburst cases were collected and 8 index rockburst sample sets were established. A variety of machine learning methods were used to analyze the feature importance of discriminant indexes in the samples, and then to determine the objective weight values of different methods. Combined with the subjective weights determined by the Analytic Hierarchy Process, the combination of weights were successively carried out. Based on the attribute recognition theory, the combination weights with different objective weight methods were established to identify the rockburst risk attributes, and verified by the confidence criterion. The results show that the objective weight value determined by the feature importance analysis of machine learning reduces the subjectivity of the weight of Analytic Hierarchy Process method, improves the prediction accuracy, and makes the prediction result closer to the fact.

Apr 26, 2022

By Juan L. Yarmuch, Hyam Rubinstein

Open-pit mine planning is a key process in the definition of mineral reserves and their efficient removal. Ore in open-pit mines is extracted bymining sequential pits called pushbacks. Pushbacks need to satisfy complex geometrical constraints to ensure the efficient usage of equipment. To date, no algorithms that both account for those constraints and maximizeNPV, are commercially available. Therefore, pushback design is done by engineers relying on their expertise to incorporate practical features intothe output of commercial tools. In this article, we present a new algorithm that produces close to optimal practical pushbacks and we illustrate its performance in real mines.

Jun 25, 2023

By Theodore H. Budd, Douglas J. Heinz

This report concerns the successful construction of Contract No. 287 of the Northeast Side Relief Sewer System for the Metropolitan Sewerage District of the County of Milwaukee. The contract involved the construction of approximately 3316 meters (10,880 feet) of tunnel concrete lined to 1.83 meters (72 inch) internal diameter; 30.48 meters (100 feet) of 1.83 meters (72 inch) reinforced concrete pipe jacked-in-place; a river crossing of approximately 107 meters (350 feet); 197 meters (647 feet) of 1.83 meters (72 inch) reinforced concrete pipe in open-cut; several diversion and flow monitoring structures; and miscellaneous manholes and appurtenances. The contract proposal, which was extremely prescriptive, did allow alternative methods of primary support consisting of precast reinforced concrete segments, steel liner plates, steel ribs with wood lagging, and combinations thereof in designated areas. The specifications required the contractor to designate which support scheme it intended to use. The specifications also required compressed air as a means of ground water control for approximately 2316 meters (7600 feet) of tunnel. The alternative selected in the bid proposal was the support method consisting of steel ribs and wood lagging for 2263 meters (7425 feet) of tunnel and steel liner plates for the remaining section. Shaft supports, by specification, were designed to be steel liner plate with steel ribs varying in size from 4.27 meters to 6.10 meters (14 foot O.D. to 20 foot O.D. ).

Jan 1, 1983

By Dion Weatherley, Raúl Castro, Pablo Cid, René Gómez

In underground mining, hang-ups due to coarse fragmentation are frequently observed in drawpoints, drawbells, and ore passes during ore draw. Hang-ups can often require operational interference and hang-up removal activities. Drawpoint and drawbell design has been shown in some studies to influence hang-ups; however, the full extent of this influence remains open to question. In this study, the discrete element method was used to analyze the effect of hang-ups on three distinct drawbell geometries: the Drawer type, Circular type, and El Teniente type. The drawer type was used as the base case given that data was available from a physical model in which hang-ups were studied. The drawer type base case data was then used to calibrate our numerical model. Results show that the El Teniente drawbell geometry sustained 13% more hang-up events as compared with the base case, while the circular drawbell geometry had 16% fewer hang-up events than the base case. From this study, it can be concluded that fewer hang-up events will occur with a rounded drawbell geometry.

Apr 11, 2023

By J. R. Koehler

Mining practices at the Sunnyside Mines, Sunnyside Coal Company, Sunnyside, UT, have been documented by U.S. Bureau of Mines researchers to preserve the extensive history of yield pillar-based longwall gateroad system evolution on the property. An overview of the historical mining conditions, practices, and innovations that resulted in the evolution of the two-entry yield pillar gateroad system currently employed at Sunnyside was developed from interviews of 30 long-time Sunnyside employees. Employing yielding chain pillars at Sunnyside virtually eliminates tailgate pillar bumps and contributes to reducing face bumps. Limiting the overall width of the gateroad system benefits bump control and especially, roof and floor stability.

Jan 1, 1994

By W. A. Crosby

The ability of open pit mines to steepen overall final wall angles allows significant cost reductions as a result of reduced waste movement requirements. Final wall angles are principally controlled by three factors: geological conditions; hydrological conditions; and wall control blasting practices. The first of these factors is not controllable by the mine operator, the second can be influenced to some degree, but the last one certainly can be controlled, hence the current interest in final wall blasting practice at many mining companies. This paper discusses common blasting techniques employed to steepen final pit walls and outlines the attractiveness of moving from small hole high cost systems to the use of full size production drills as a means of reducing wall control blast costs. Attempts to make this change have been limited at many mines by the physical size of the drills and their inability to reverse drill. In the past, pres pi it, pre-shear or trim holes have had to be drilled vertically, at considerable distance from the upper bench toe, with the result that inter-berm face stability is reduced and final wall angles have to be made somewhat more shallow than desirable. The paper concludes with a description of how these problems can be overcome by utilizing the new Bucyrus 39R which has the capability of drilling at a ?15 degree angle underneath the machine. It is concluded that the resulting wall control blast designs will offer large mines improved final wall angles with resulting significant overall cost reductions.

Jan 1, 1998

By P. R. Taylor

A cyclone reactor system for the partial reduction and melting of taconite concentrate fines has been engineered, designed and operated. A non-transferred arc plasma torch was employed as a heat source. Taconite fines, carbon monoxide, and carbon dioxide were fed axially into the reactor, while the plasma gas was introduced tangentially into the cyclone. The average reactor temperature was maintained at above 1673 K (1400 C), and reduction experiments were performed under various conditions. The influence of the following parameters on the reduction of taconite was investigated: carbon monoxide to carbon dioxide inlet feed ratio, carbon monoxide inlet partial pressure, and average reactor temperature. The interactions of the graphite lining with carbon dioxide and taconite were also studied.

Jan 1, 1993

By I. G. Bowen

The pumping of abrasive and sometimes corrosive slurries is normally carried out at modest heads (say 100 ft) with specially designed centrifugal pumps. When heads become higher than this, two or more pumps are used in series but ultimately the system requires staffed pumps with consequent increase of costs. The only other type of pump suitable for high heads is the Ram pump but this is notoriously subject to wear. The paper describes a novel application of the so-called "lock hopper" principle to continuous pumping of slurries. The pump itself is never in contact with the abrasive slurry nor is it subject to head or capacity limitation. It works by displacing slurry with the clear fluid component of the slurry (in most cases water) through cylindrical vessels fitted with plug valves to control the discharge and filling operations. Two such vessels are used and the scheme is completed with a liquid clarifier which allows the pipe flow to be maintained continuously. The paper describes experience on the prototype unit used to discharge tailings from a coal washery in Scotland. A tentative evaluation is also made of the economics of this pump against conventional equipment.

Jan 1, 1965

By Randall C. Divito, Craig R. Eckdahl, Bruce D. Wagener, Joseph Klejwa

The existing Central City Tunnel was built primarily in the 1930s with a small portion as old as the 1880s. It conveys stormwater in downtown Minneapolis. It is a 4,400-ft long tunnel located 80 feet underground. The Central City Tunnel has experienced surcharging and surface overflows during heavy rainfall events. This paper presents the details of tunnel and shaft design for the new Central City Parallel Tunnel to mitigate the overflows. The design considered hydraulics and geotechnical engineering for the structural geologic conditions including the weak Saint Peter Sandstone and overlying strong Platteville Limestone. Ground conditions resulted in tunnel designs including large flat-back box tunnels and unique cathedral-shaped tunnel sections.

Jun 13, 2023

By Stephen D. Schwochow

Aggregate producers nationwide well recognize the numerous problems often faced in securing local approval to open and operate new gravel pits and rock quarries. Similar problems are faced in Colorado, but this region also presents certain political, social, and geological complexities that have become particularly troublesome in the last 10 years. The gravity of the local permitting dilemma can be related directly to the worsening supply-demand imbalance for aggregates in the state's most populated area, the Front Range urban corridor, particularly the Denver metropolitan area. The drive to develop crushed-rock reserves to supplement dwindling alluvial supplies and to meet increasing regional growth demands was somewhat predictable but perhaps more a "last resort" alternative forced onto producers by a hesitant and often apathetic government.

Jan 1, 1982

By James Westfield

I welcome this opportunity to appear before you and to review briefly the various health and safety services of the Bureau of Mines available to the mining industry, other than coal, and also to tell of our plans for extending these services to improve safety and health conditions. The Bureau's health and safety activities are basically services by which we attempt to develop and disseminate information on improved techniques in mine accident prevention and promote mine safety education in the mineral industries. Unfortunately, some mining companies, particularly some of the smaller operations, seem to be unfamiliar with these services, The Bureau of Mines is charged by law with the responsibility for inspecting coal mines; other services to the coal mining industry and are provided only on request, Safety inspections and other services that we offer are provided for noncoal mining industries solely upon request.

Jan 1, 1958

By P. Bartel

Coal cleaning can be effected by the bacterium Sulfolobus acidocaldarius, which in oxidizing sulfur and dissolving mineral matter requires carbon dioxide and oxygen; carbon dioxide as a carbon source and oxygen as an electron acceptor. The desulfurization of coal by thermophilic bacteria under elevated partial pressures of carbon dioxide and oxygen was studied at a total pressure of 1 atm. The partial pressure of carbon dioxide was varied over the range 0.00032 to 0.33 atm (0.00032, 0.007, 0.10, 0.33 atm), and the partial pressure of oxygen was varied over the range 0.14 to 0.40 atm (0.14, 0.21, 0.30, 0.40 atm). The maximum rate of coal desulfurization increased by 32%, from 9.0 to 11.9 mg S/1 hr, as air was enriched in carbon dioxide from its atmospheric level of 0.00032 atm to 0.10 atm. Enrichment with carbon dioxide up to 0.10 atm, at constant oxygen partial pressures, increased the desulfurization rate, but enrichment to 0.33 atm caused the rate to decrease. At constant carbon dioxide partial pressures, the desulfurization rate was maximum at oxygen partial pressures of 0.21 and 0.30 atm. At higher (0.40 atm) and lower (0.14 atm) oxygen partial pressures the rate decreaed by 9 to 20%. The desulfurization rate decreased by 58X, from 9.0 to 3.8 mg S/1 hr, when the air pressure was increased from 1 atm to 3 atm. The effects justify an economic analysis during design and operation of a commercial air feed in a process to desulfurize coal by microbial action.

Jan 1, 1986