Search Documents

By Toru Nakao

Fujiwara Quarry had been operated by the "Glory-hole Benchcut" mining system. But because it became difficult to meet the expanding demand by this system, "Central- shaft MCP" mining system was introduced in 1979. This MCP is equipped with a hydraulic walking system manufactured for the first time in Japan. Nowadays "Central-shaft" mining is the common method at limestone quarry in Japan. In this method crushing facilities are usually installed at the bottom of the shaft. But at this quarry, MCP was adopted and installed on the quarry surface. Many MCPs are operated in foreign countries, but in Japan few examples exist. Normally, Japanese limestone deposits lie in high mountains, which is obviously inconvenient for MCP to walk in and around the quarry. This difficulty, however, was overcome at this quarry, and MCP has been operated satisfactorily and efficiently for about 2 years after it was installed. In order to overcome the difficulty, in "Cen¬tral-shaft MCP" mining system, two mining methods are employed, the one is "SLICE-DOWN" mining method, and the other is "BLOCK-CUT" mining method.

Jan 1, 1982

By Fabiola Espinoza Carmona, Elena Chiriotti, Edoardo Misano

"INTRODUCTION Ganntas Tunnel is part of the modernization project of the railway between Alger and Oran, in Algeria. In order to double and rectify the existing line between El Affroun and Khémis Miliana, the alignment foresees the excavation of a 7 km-long twin tunnel. The excavation works started in June 2011 with the contractor CCECC, under the supervision of SYSTRA. Excavation is driven in conventional method by hydraulic hammer simultaneously on 8 different faces since excavation was started also from a junction window towards the middle of the tunnel. The minimum longitudinal distance to be respected between two contiguous tunnel faces has been set to 30 m. The tunnel cross-section is a 70 m² oval shaped profile, temporary support consists of shotcrete, bolts and steel ribs. A 30 to 50 cm thick cast in situ concrete final lining has been provided as well. When the tunnel reached a fault zone in soft clayey marls extreme squeezing occurred, works were stopped and re-profiling operations were carried out along more than 100 m. To date, works proceed at slow rate since high convergences are still monitored and completion of works is not expected before December 2016.GEOLOGY The project is located within the Tellian Atlas mountain area, including in particular the Djebel Ganntas massif in between Mitidja and Chleff plains. Djebel Ganntas is characterized by an extensive massif aligned in East-West direction with smooth slopes made of soft clays that emerge in multiple cliffs and ravines. On the top of it, along the edge, a more recent sandstone formation is found. The existing data on the geology did not allow to establish an accurate geological model at tender stage. In-situ investigations allowed at design stage to identify a Quaternary alluvial cover of clays and gravel, followed by a Miocene stratum divided in a sandy top layer and a lower clayey layer. From a structural point of view, geological maps suggest a north direction dip of layers, but the in situ surveys showed that layers were highly folded. The lack of information at tender stage on the structure of the geological series should have triggered an extensive investigation campaign at detailed design stage which did not take place causing serious consequences on costs and time at construction stage."

Jan 1, 2016

By Mogens Henriksen

In the past decade, numerous urge scale drilling projects have made use of reverse circulation air lift methods. Reverse air lift pumping can be established by injecting gas into a column of liquid; the subsequently decreased density of the gas-liquid mixture allows atmospheric pressure outside the lift conduit to establish flow. The rate of flow can be controlled by varying the gas to liquid ratio. A typical reverse circulation air lift system is depicted in Figure 1. Allen1 has described a number of reverse air lift drilling projects. Although cited examples are generally related to large diameter holes, the method has seen use in other applications such as sand dredging, chemical pumping, water well pumping and continuous coring. One particular benefit obtained with enclosed reverse circulation drilling is elimination of lost circulation. The required air/water ratio for pumping at a given submergence and lift has been established experimentally by Gibbs2. His data, however, do not reflect sensitivity of flowrate to air/water ratio. Further, in Gibbs' work, air apparently is injected continuously along the column of water. This configuration differs from that used in reverse air lift drilling where air is injected at discrete points only. Gas lift theory has received considerable attention over the past decades. Orldszewski3 defined flow regimes in two phase flow. Griffith and Wallis4 determined relative velocities of gas to liquid. Two-phase flow has been studied extensively for oil transport in inclined and vertical pipes by Chierici et a15, Beggs and Brill6, and Gould, Tek and Katz.7

Jan 1, 1977

By L. D. Hartzog

A pilot plant investigation of a semi-autogenous mill - ball mill circuit is described. The plant was operated with minus eight-inch diabase as feed material to the semi-autogenous mill. The semi-autogenous mill recycle screen underflow was put to a ball mill in closed circuit with a cyclone. An operating Work Index of 13.3 to 14.9 was obtained with the pilot ball mill. This Index is substantially in agreement with the scalped feed laboratory Work Index for 15.3 for recycle screen underflow. The Bond Index of the diabase was 15.8. Thus, one may use the scalped feed laboratory Work Index to size semi-autogenous grinding plant ball mills.

Jan 1, 1974

By R. Svensson

Mill linings play an important role in all comminution processes with tumbling mills. The selection of the lining profile and the lining material has a great impact on over-all grinding cost and mill throughput. The cost of the lining itself is minor in comparison with media cost, energy cost and the value of the material produced in the mill. The total scope must be considered when mill linings are selected. This paper presents case stories and explains the technology behind: -different lining profiles in rubber and steel -OREBED magnetic lining -Steel-cap rubber lining

Jan 1, 1994

By G. Ferrara

To obtain a reliable comparison between conical and cylindrical separatory vessels used in dynamic dense medium separation systems, the following studies were made: (1) study of the swirling flow in conical and cylindrical vessels using laser-Doppler velocimetry (LDV); (2) study of the behaviour of suspensions of magnetite and ferrosilicon in water in both separators. It was found that: (a) the tangential velocity profiles differ in conical and cylindrical vessels: in a conical cyclone free vortex conditions affect the largest part of the vessel, while in a cylindrical vessel, the motion approaches that of a forced vortex, i.e. that of a centrifuge; (b) the conical vessel manifests higher centrifugal acceleration and very strong densifying; the density differential, and hence the density gradient inside the vessel is large; (c) the cylindrical vessel manifests lower centrifugal acceleration and low densifying, i.e. low density differentials, and hence, the density gradient inside the vessel is small; (c) due to greater densifying, the density cut-point in cyclones is higher than the operating medium density, while in cylindrical vessels the density cut-point is closer to the medium density. The results provide an interesting description of the differing behaviour of conical and cylindrical vessels and help explain the differences in performance between the two types of separators.

Jan 1, 1998

By Fred Pena

The VERTIMILL has proven itself to be a reliable performer in heavy duty industrial applications. Applications have been extensively used in the mining industry, flue gas desulfurization applications, and industrial minerals field. The machine is a vertically stirred machine that utilizes a screw operating in a grinding media. Grinding media types have ranged from several sizes of steel balls as the most common to pebbles or ceramic media. Mesh-of-grind and final product size are the determining criterion for the selection of the media size used. Product size consists have ranged from very coarse to super-fine grinds of less than 25 microns. Savings in consumption of power, grinding media, and liners when compared to a conventional ball mills, have been realized. Savings in consumption of reagents have also been demonstrated.

Jan 1, 1992

By Young C. Kim

In the past, underground coal mine planning has traditionally focused on the mine design n aspects concerning safety and efficiency in the quest to produce low cost coal. Very little attention has been given to coal quality control aspects of mine planning at most of the underground coal mines within the U.S. With the enactment of the clean air act of 1970, the generally high sulfur content of coal has become a major concern for the coal-fired power plants in the east. Similarly, the ash and the BTU contents of coal are of equal importance from boiler efficiency standpoint. Thus, the time has come when the coal mine planning must incorporate the coal quality control aspects as well as the traditional safety and efficiency aspects.

Jan 1, 1983

By M. D. Lawton

Anglo-Rouyn Mines Limited, managed by Rio Algom Mines Limited is a subsidiary of the British-based Rio Tinto-Zinc Corporation Limited. This mining operation is situated in Northern Saskatchewan, 250 miles north of Saskatoon and represents the first base-metal mine of any importance served by this relatively new mining province. The outcrop of Copper-bearing Chalcopyrite was first discovered by prospectors in 1915, but was not mined until 1965 due to the absence of any form of road into the area prior to this latter date. The mine, mill and concentrator were designed to handle 900 tons per day of comparatively hard, abrasive ore containing chalcopyrite with traces of gold and silver. The flow sheet, Figure 1, is, we believe, elementary, designed with low cost in mind and utilises much old equipment from closed¬-down mines. Due to some difficulty in attaining the designed grinding capacity, changes were made in the crusher circuit. This, unfortunately, lowered the crushing rate too much. A series of changes have taken place to re-establish the original crusher capacity of better than 100 tons per hour. In the quest for a better recovery certain modifications have been tested in the concentrator circuit. These steps are discussed in minor detail.

Jan 1, 1970

By Donald Towse

Portland cement is a basic building material in every country in the world, and, fortunately, the raw materials required in its manufacture are widely distributed. It is a low-priced bulk commodity (price one cent a pound or less, with a density of 100 pounds per cubic foot.) Table 1. Approximate price per pound of selected mineral products. Copper 48 cents per pound Aluminum 27 Lead and zinc 15 Asbestos 3 to 18 Pumice 6 Sulfur 2 Bauxite (abrasive) 1.8 Barite 1 to 1.6 Cement 1 Primitive regions may get along without any Portland cement, but most countries use some, and it is one of the most widespread building materials, even if used in small quantities. Use of cement begins early in a country's development, and, because of local availability of raw materials, cement manufacture is one of the first heavy industries many countries desire. Use and manufacture of cement usually precedes other industrial materials such as steel and heavy chemicals, and consumption levels off for a long period during development of infrastructure and an economic base. With a mature economy comes a very high consumption. Per capita consumption varies ten times or more between nations (Figure 1).

Jan 1, 1970

By Peter Zhang, Daniel Su, Bo Hyun Kim

Shale gas wells drilled in longwall chain pillars are influenced by longwall mining. Longwall mining on each side of the chain pillars can create overburden movements and induce deformations in gas well casings. If the deformations result in a casing breach, intrusive shale gas could leak into the longwall mine with serious safety consequences. This study concerns five shale gas wells in the chain pillars between two adjacent longwall panels in the Pittsburgh coal seam under a cover depth of 670 ft and a mining height of 7 ft. The gas wells were constructed with typical casing design, but a casing cementing alternative with uncemented production casings was practiced. Four production casings were uncemented, and one production casing was unintentionally cemented with good quality cement to a 535-ft depth and low-quality cement stringers from a 444- to 535-ft depth. The longwall faces passed by the shale gas wells as each adjacent longwall panel retreated. Production casings were surveyed by a multi-finger caliper after each panel was mined. No deformation was detected in the four uncemented production casings, but small deformations were detected in the partially cemented production casing. The maximum measured deformation in the cemented production casing was 0.05 in. after first panel mining and 0.06 in. after second panel mining. The casing deformations were also predicted by the FLAC3D model set up on site-specific overburden geology. The predicted deformations were in good agreement with the measurements in terms of deformation locations and magnitudes. All five shale gas wells resumed normal production after being temporarily plugged during the period of mine-by. This study provides a successful demonstration of the effectiveness of a casing cementing alternative for decoupling production and intermediate casing, and thus minimizing the influence of longwall mining in the shale gas wells drilled through longwall chain pillars.

Jul 1, 2023

By M. B. Thorpe

Land use and access to land are limiting factors in economic development in the Western region of Ghana. Mining uses land during operations and then rehabilitates the land as part of ongoing operations and closure. Golden Star Resources Limited (GSR) aims to contribute to the sustainability of the local economy during its operations and then post-closure. Following a series of alternative livelihood initiatives, GSR reviewed the success of these programs and decided to focus on an oil palm project that uses out-growers to reach the local economy. The project started using small holdings that were individually managed. However, the ongoing effects were limited. Following a review of the options, the Golden Star Oil Palm Project was started using land committed to the pro-gram by the Bogoso Mine. The initial program covered 275 ha with over 40,000 trees with 300 people involved in the development. The Traditional Authorities have committed additional lands to the project to a planned total area of 18,000 ha.

Jan 1, 2007

By K. G. Colman

Este texto intenta facilitar al operador y contratista 10s datos básicos para dimensionar las cribas vibrantes que deban ser utilizadas en las plantas de trituración. Las capacidades básicas, factores que la modifican .... etc., utilizados en el cálculo de la superficie requerida, se han desarrollado empíricamente y modificados sus valores hasta el presente con 10s datos de las aplicaciones prácticas Hay que señalar que el cribado tiene mucho más de arte que de ciencia exacta; sin em- bargo, la información aquí presentada proporciona una razonable seguridad cuando se aplica al cálculo de cribado de minerales metálicos.

Jan 1, 1982

By Donald L. King, Frank A. Baczek

Sedimentation-based equipment is used in applications where separation of solids from liquid by gravity settling is desired. If a concentrated solids slurry is desired, the equipment is designed to "thicken"; if a clear liquid is desired the equipment is designed to "clarify." Thickeners normally handle higher solids loading rates than clarifiers, which usually process feed slurries containing low concentrations of suspended solids. Thickeners are therefore designed for heavier-duty requirements, and clarifiers have extra features to ensure more complete suspended solids removal. Major components (Figure 1) that are common to all sedimentation-based equipment are: tank, drive-support structure, drive unit and lifting device, rake structure, feed well, and a means of overflow and underflow withdrawal. Specific features are designed interdependently after the overall separation approach is defined conceptually. This conceptual approach is usually based on past experience or evolves from sedimentation studies conducted on samples of the slurry to be handled. Because many variations and combinations of components are possible, the overall conceptual approach has a number of possible designs that will accomplish the desired results. The final choice is based on practicality, potential for minimizing upsets, and cost.

Jan 1, 1986

By K. Adam

Uncontrolled disposal of pyrite wastes and concentrates comprise a major source of acid drainage in active and abandoned sulphide mines. In this paper, the state?of-the-art mitigation measures implemented for the final reclamation and closure of a pyrite concentrate stockpile at Platia Karra, Stratoni mines, Greece, are presented.

Jan 1, 2002

By James A. Barclay

Results of investigations over approximately the last 10 years by the Bureau of Mines and others on technology for recovering cell-grade alumina from domestic nonbauxitic resources such as clay, anorthosite, alunite, dawsonitic oil shale, coal ash, and coal shale are reviewed. It is concluded that, although many innovative techniques have evolved from this effort and have been shown to be technically feasible, energy and economic considerations will prevent any of the processes from competing with the Bayer process under normal conditions. Based on the Bureau's experience, some variation of clay-HCI leaching, HC1 gas sparging crystallization has the greatest potential as an alternative to the Bayer-bauxite process.

Jan 1, 1984

By W. G. Miller

A series of computer programs for the analysis and mapping of coal-related data has been developed at the Illinois State Geological Survey; these programs, known collectively as the Coal Data System, represent the latest achievements in computer processing of geologic data at the Survey. Building upon programs previously developed in the Survey's Computer Services Unit, they expand the scope of the computerized data base that the Survey has been using for analyzing coal-related data. The System was partially developed during a joint study by the Illinois State Water Survey and the Geological Survey entitled, ?Coal and Water Resources for Coal Conversion in Illinois.? 2 In that study the available coal reserves more than 42 inches thick in the two principal coal seams throughout the state were mapped. The System was used to calculate the coal reserves and to report the average number of tons of coal in place per square mile in each township (Figures 1 and 2). It also produced maps of the coal features of sufficient quality to be printed on material that was scribed as master copy for the printing of full-color 1:500,000 scale maps (see Figures 3 and 4).

Jan 1, 1975

By Josef J. Schwegel

The first vertical shaft lime kiln operating according to the parallel-flow regenerative principle was developed and built in the nineteen-fifties by Schmid-Hofer in Austria. Upon proving this concept of calcining or "burning" limestone to be very energy efficient for the production of good quality lime, Maerz Ofenbau AG of Zurich, Switzerland was in 1965 licensed for the design detailing and construction of these kilns. The first regenerative shaft type lime kiln outside of Austria was built in 1966 and through close co-operation with customers and their operating personnel, the advanced technical developments of today's kiln designs were accomplished. At present approximately 190 kilns of this type in capacities ranging from 60 to 700 short tons per day have been built or are under construction throughout the world in highly industrialized as well as less developed countries.

Jan 1, 1981

By Sam H. Patterson

Australia has led the world in bauxite production since 1976, and only the Republic of Guinea has larger bauxite resources. India has a small integrated aluminum industry, and deposits containing more than 1 Gt (billion metric tons) of bauxite were discovered in the 1970's. The Peoples Republic of China has large bauxite resources scattered in several regions, but it is a monohydrate type that is difficult to process for aluminum. Indonesia and Malaysia both have long histories of bauxite mining, and both have limited resources of high-grade bauxite. Districts containing bauxite resources in the 10 Mt to 150 Mt (million metric tons) range are scattered in countries along the eastern rim of the Pacific Ocean, on islands in this ocean, and on the western and northern rims of the Indian Ocean.

Jan 1, 1982

By William C. Grady

The environmental and economic problem created by pyrite in coal are well documented. The removal of pyritic sulfur prior to, or during, utilization has been the object of considerable research, however, much of this research has proceeded without a proper knowledge of the microscopic occurrences of pyrite in coal. This paper investigates the forms, occurrences, and variations in the distribution of pyrite in major West Virginia coal scan. Twenty-nine samples from twenty-two major west Virginia coal scans were selected for this study (see Table I). The samples were selected so as to be representative of the major coal producing areas of the state. All samples, except five, were collected at active surface mines, as indicated in Table I, and all except one were channel samples. The time interval between sampling and preparation of polished microblocks varied from two months to two years, though most were prepared within three months of collection. Grinding, screen¬ing, and riffling of samples to obtain 250 grams of -20 mesh coal for microscopic analysis strictly followed ASTM procedure D2013-72.

Jan 1, 1976