Search Documents

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as a high value-in-use sandblasting agent, as a premium-grade foundry sand, and as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. Staurolite is produced by E. I. duPont de Nemours and Company as a coproduct of titanium mineral production in Florida, where it was first recovered on a commercial scale in 1952 from the Pleistocene sand deposit known as Trail Ridge. At this deposit it comprises about one-fifth of the heavy mineral suite, the principal other heavy minerals being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and other nonconductive silicate heavy minerals are separated from the conductive titanium minerals on high-tension electrostatic separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total process, 200 t of raw sand yield 7 t of heavy mineral concentrate from which about 1 t of staurolite is recovered. The staurolite concentrates have the characteristics given in Table 1. Staurolite concentrates are sold in three grades having the size distribution of subrounded grains shown in Table 2. All three grades are used in sandblasting for cleaning metal, for paint removal, and for cleaning masonry buildings. Staurolite compares favorably with lower priced abrasives, such as boiler slags and silica sand, in applications where the abrasive is used only once and is not recovered and recycled. Because it is hard, fine, clean, and dense it can reduce blasting time, and less material is required to clean a specific area. Compared to higher priced abrasives such as aluminum oxide and garnet, which are recycled, staurolite costs significantly less per kilogram and cleans at equal or faster rates. Its breakdown factor, which is a measure of recycling performance, is intermediate between those for aluminum oxide and garnet. [ ] [Tables 3 and 4] show the blast cleaning performance of the three staurolite grades compared to other abrasives. [Table 5] compares the longevity of premium priced abrasives during recycling. [Table 6] shows a cost comparison between silica sand and staurolite. Fringe benefits claimed for staurolite's use as an abrasive are: 1. Good flow properties and freedom from the lumps or slivers found in silica sand or boiler slag abrasives. 2. Low dusting affords good visibility, permits faster working, and reduces cleanup problems. 3. Heated storage is not required during freezing conditions, because the mineral is nonhygroscopic.

Jan 1, 1994

By R. E. Muller, L. G. Martin, J. M. Stonehouse

Erratic distribution of values in free gold ore bodies presents severe problems in sorting material in large scale open pit mining. However, an intense program of modern blasting techniques and less than modern gold panning results in good sorting at Houston International's Manhattan mine. Blasting technique is important. If the sample location cannot be relocated because of blasted material movement, information acquired while drilling is useless. So short benches are critical to minimize dilution. Though not very accurate, panning allows for rapid analysis. The more accurate fire assay does not provide the needed speed. Panning can be fairly accurate and errors made are mostly on the low side. Samples of mixed and broken stockpile material are used as checks on pit procedure and to develop stockpile content in¬formation. Added tonnages discovered offset the higher labor costs of this careful sorting technique. The mine is located in central Nevada's Toquima Range in the small mining town of Manhattan, 322 km north of Las Vegas. The mine has four epithermal stockwork ore bodies that are mined in two pits. The mine problem was that conventional ore control was not separating ore from waste. Assays of 6-m blast-holes were used on 5-m centers. The blastholes were relocated by stadia survey after blasting. Holes assaying above the cutoff grade were flagged and mined as ore. This system is practical and useful in high concentration ore bodies or in evenly disseminated mineralization. But it was not practical at Manhattan because of large gold particles and small ore pocket sizes. Ore pockets were often missed when drilling a grid area for blasting. Also, large gold nuggets made assay results unreliable. The probability of a nugget being contained in an assay charge is small. So most results were low, compared to actual grades mined based on stockpile samples. When a nugget found its way into a fire assay charge, the result would be far higher than the actual grade of material represented. In addition, disturbance by blasting created problems in relocating ore. Because of these problems, the grade control program was intensified in September 1979. It successfully separated ore and waste in blocked out ore areas and located more ore in "waste" areas. Known reserves mined to date have increased up to 50% on some benches. The methods used are modern blasting techniques, detailed assaying, and traditional panning of samples collected from active mining faces. These methods allow mining flexibility, to match the variable mineral occurrence in ore bodies. The united effort of the geology and engineering departments has been important to the program's success.

Jan 12, 1980

By Claude Froger

The compared advantages of digital and analogue computers for solving ventilation problems have for many years been a matter of discussion among the specialists whose respective arguments have prevailed in turn depending on the progress of technology. In the French coal mines however none of these two techniques has superseded the other so far. In France, between 1956 and 1962 only the digital computer and from 1962 to 1967 only the analogue computer was used. Since then they are both used concurrently and complementarily. Depending on the problems dealt with, the most advantageous method is chosen in each case. In the case of ventilation planning for projected workings, it is possible to test variant forms of the development plans and many parameters can be varied. In such a case the flexibility of the analogue computer is a great help. Wrong lines taken will be rapidly abandoned and little by little solutions will be found. By examining the results of a test, new ideas will generally come into the mind and they can be tested right away. Such an investigation is always-carried out in conjunction with the engineers of the mine concerned. In complex networks it often leads to solu¬tions which could not have been devised from the start. The same work could be done by using a numerical method and the digital computers operating in the different coal mine districts, but for the same tests, the time required would be much longer and the participants would not be encouraged to use their imagination so intensively. Or the other hand for calculations of ventilation networks in ventilation surveying, use is made of the digital computer which gives the possibility of storing the data corresponding to the different mines concerned. The questions to be solved concern problems for which the ventilation network is essentially known, and in which only a small number of parameters can be varied. The few possible alternatives to be calculated can therefore be handled by the digital computer in spite of the relative lack of flexibility of the method. To sum up our ventilation studies are conducted in France as follows: - For ventilation studies and modifications due to projected workings use is made of the ana¬logue computer. For a given mine the updating of such ventilation studies is carried out every 3 or 5 years according to the progression of the workings. - For ventilation surveying while normal working operations are in progress, use is made of the digital computer.

Jan 1, 1980

By Wenming Wang, Edgar E. Vidal, Scott A. Shuey, Patrick R. Taylor, Judith C. Gomez

Introduction In modern society, vanadium is defined as a strategic metal. Some 90% of the global consumption is used as an alloying agent for carbon steels, tool steels, and high-strength low-alloy steels (particularly for pipelines). Advanced titanium-aluminum-vanadium alloys are seeing application in the aerospace industry. Small but ever growing amounts are finding application as catalysts or in electronics. New uses are continually being discovered for this metal. One example of a new application is the vanadium-redox battery for use in generation plants and back-up power sources. Vanadium is found in a large number of minerals, of which the most important are carnotite, roscoelite, vanadinite, mottramite, and patronite. Just over a third of the world's vanadium is produced as a primary product; the balance is a by-product of the iron and steel, oil refining, power generation and uranium enrichment industries. Vanadium can also be sourced by recycling spent catalysts from the petrochemical industry and ash produced by the combustion of oil emulsion in power stations. However, recycling activities are believed to account for only a small amount of total world supply. Vanadium is recovered from these ores largely as the pentoxide (V2O5) [1]. The major sources of vanadium-bearing magnetite ores are scattered throughout Australia, China, Russia, and South Africa. Current estimates of world’s Proven & Probable vanadium reserves are of the order of 41.3 million tones [2, 3]. Commercial vanadium-bearing titaniferous magnetite deposits can be found in Kachkanar, Russia; Pan Zhihua, China; Bushveld, South Africa; and Windimurra, Western Australia [4]. Other deposits have been found in New Zealand, Canada, and India, among other countries. Vanadium consumption in the steel sector has increased some 7% per ton of steel over the last 10 years as new alloying applications have been found to improve steel's strength-to-weight ratio. Future demand from the aerospace and nuclear industries for non-ferrous vanadium alloys such as titanium and super-alloys is also likely to grow. Vanadium is usually added in the form of ferrovanadium, a vanadium-iron alloy. Vanadium compounds, especially the pentoxide form, are used in the ceramics, glass, and dye industries, and are also important as catalysts in the chemical industry. While established approaches may be used at an industrial scale to treat vanadium-bearing titaniferous magnetite ores in several countries, new alternatives are being developed worldwide. This review will give short overview of the treatment of vanadium-bearing titaniferous magnetite ores, an overview of direct reduction and direct smelting processes and an approach to determine technical alternatives for the property.

Jan 1, 2005

By Cong Zhang, Huaying Wang, Yixin Wei

"Water inrush is a serious geological accident in underground coal mines. This paper focuses on the method of the bow tie analysis based on fuzzy reliability to assess the risk of water inrush in coal mines. First, post failure probability and repair probability of initiating events are divided into 5 levels. Then triangular fuzzy numbers are adopted to quantify experts’ language and to acquire the reliability rate which close to the actual values by defuzzification and calculation. According to dynamic bow-tie analysis model, using the method of moments to fit the reliability time of events by Weibull distribution and offering the random sampling rule of failure and repair time for illustrating the feasibility of fuzzy reliability evaluation. To demonstrate the effectiveness of the proposed assessment approach, bow tie analysis model of water inrush in coal mines is taken as an example.Introduction Dynamic bow tie (DBT) analysis is composed of dynamic fault tree and dynamic event tree analysis, and considers the impact of the time factor upon risk assessment of a system. There are many algorithms applied to calculation of the probabilities of node accident and accident consequence of dynamic bow tie analysis: Hidden Markov Model, Bayesian Network (Khakzad et al 2013), Integral Algorithm (Amari et al 2003) and Monte Carlo Simulation (Kim et al 2016). In terms of simulated time and practicability, the Monte Carlo Simulation has an advantage over other methods. DBT requires mass data in quantitative analysis, including the failure rates and the repair rates of the basic events of the Fault Tree (FT) and the subsequent events of the Event Tree (ET) at different time points, i.e., the distribution of failure time and repair time. In practical analysis, it is hard to obtain a large amount of exact historical statistical data, which is a major problem of risk assessment. Due to the difficulty of obtaining the exact data and historical failure data of the basic events and the subsequent events, the FT and ET analysis is stuck with the study of minimal cut sets, minimal diameter sets, structural importance and qualitative analysis (Liu and Zhang 2010, Yan et al 2012, Wang et al 2009, Li and Wang 2011). This paper will use fuzzy numbers and the defuzzification method to transform the experts’ language into the failure rates and repair rates of basic events and subsequent events, solving the problem that it is difficult to obtain a large amount of historical statistical data, and will use the method of moment to conduct Weibull fitting of the reliability time to provide the random sampling criteria of event failure and repair time in Monte Carlo simulation."

Jan 1, 2017

By R. L. White

Classification of Mills Mills may be classified under four categories that relate to the type of action utilized to grind the material: Tumbling. The most important of these to the minerals processing industry are tumbling mills. Grinding media is actuated in a free¬form pattern in a rotating drum causing it to tumble, material being ground passing through the tumbling media. Work is done by a combi¬nation of attrition and impact. Impact. Grinding media is actuated in a distinctive pattern so that it impacts the material being ground. Work is done by impact. Roller. Grinding media is actuated in a distinctive pattern, mate¬rial being ground passing under or between the media. Work is done by compression. Fluid Energy. There is no grinding media as such. Energy is imparted to the material by transfer of kinetic energy from the fluid to the material. Grinding is accomplished by interparticle impact and attrition. Tumbling Mitts The main physical arrangement consists of a lined cylindrical drum mounted on trunnion bearings driven by a ring gear and pinion, in turn connected directly or through a reducer to the electric motor. Variations to this general arrangement include: (1) Drum mounted on rollers instead of trunnions. (2) Bearings on the drum directly, not on trunnions. (3) Utilization of multiple pinions on the gear. (4) Trunnion-type drive arrangement through a gear reducer with¬out the use of a ring gear. (5) Motor rotor mounted directly on the drum with stator around the drum, thus eliminating the gearing. The drum consists of a shell and heads lined with replaceable liners of various types and configurations. Various types of tumbling mills are tabulated; illustrations of some are shown. The types are so designed for specific purposes. Media utilized include steel rods, balls, or rock of the same material as being ground or of special material in the instance where iron contami¬nation is detrimental (see Figs. 9 and 10 and Table 2). Impact Mills Although there may be some overlapping of interpretation of terms, impact mills are considered those in which the media is actuated in a distinctive manner, at relatively high speed, impacting the material to be ground. There is an overlapping also in what may be considered to be crushing equipment rather than grinding equipment. Hammer Mill or Impactor. Material is fed into the equipment; inside hammers of impactors revolve at a high speed, breaking the material on impact with the hammers (see Fig. 11). Material is also thrown against the periphery of the mill, causing impact grinding to occur. Equipment is normally lined with replaceable abrasive resis¬tant metal; hammers are also

Jan 1, 1985

Drainage and erosion control often become problems at mine reclamation projects. An example of this was an abandoned surface uranium mine on the south Texas plains. Engineers with the Texas Railroad Commission solved these and other problems with a three-dimensional geomatrix erosion-control matting at the 69-hm2 (170-acre) site, about 70 km (45 miles) southeast of San Antonio. Enkamat, manufactured by Akzo Nobel Geosynthetics, was installed to reinforce the grass waterways that handle runoff from the reclaimed mine. Reclamation was completed in the spring of 1992. Bill Walker is regional manager for Erosion Control Systems. He worked with the contractor to identify an erosion control product that complied with the project's design and installation parameters. "Use of erosion control matting enabled us to reduce erosion control costs," said Mark Rhodes, with the Texas Railroad Commission. "Also, the erosion control material was more aesthetically compatible with the reclaimed landscape." The commission's design called for a terrace ditch to be constructed midway up the reclaimed spoil slope to catch and collect water. Commission engineers selected spoil slopes, ranging from 5% to 8%, to build reinforced grassed waterways to drain the collected water from the terrace ditches. This was done instead of dropping the water at steeper slope location in rip rap- or concrete-lined channels. Enkamat's three-dimensional geomatrix of heavy nylon monofilaments is 95% open space that aids root growth. Its root-reinforcement system resists the hydraulic lift-and-shear forces created by high-volume discharges of water. In addition, fine eddy turbulences are prevented from isolating and uprooting individual roots and clumps of vegetation. Enkamat is flexible and lightweight. This makes it easy to install. And, because grass grows into it over time, it "disappears" after installation. Between 12,540 and 14,200 m2 (15,000 and 17,000 sq yds) were installed in the waterway using 150-mm (6-in.) staples to fasten the matting, said contractor Dale Blackstock. "It was easy to use; no problem at all to put down." Blackstock selected Enkamat from a list of eight different channel lining materials described as acceptable in the commission's design specifications. The design specifications were based on the results of channel-lining performance tests conducted by the Texas Department of Transportation. Rhodes said that the commission's Abandoned Mine Land Reclamation program had installed Enkamat on other abandoned uranium mines and on an abandoned surface lignite mine near Austin. "Pretty much all of our installations of Enkamat have worked out well," he said. "There have been no failures. The reinforced grass waterways have performed as designed."

Jan 1, 1998

By John H. N. Yen, James M. Marquardt, Larry H. Heflin

INTRODUCTION On February 17, 1995, WMATA Contractor J.F. Shea holed through the last segment of rock tunnels of the planned 103-Mile Rapid Transit System for the Washington Metropolitan Area Transit Authority. Through the joined efforts and cooperation between the owner and the contractor, the project was completed on time and within budget. The Glenmont extension is on schedule to open in Mid-1998. The complete 103-mile system is scheduled to open in 2001. WMATA’s earlier 19 miles of rock tunnels had been done since 1976 ? By drill and blast with heavy horseshoe steel sets, sets with shotcreting over wire-fabric by TBM and NATM. All rock tunnels were primarily in metamorphic gneiss and schist, part of an east coast lithology that outcrops in a band running from below Richmond, Va. To above New York City. The 5,400 ft. long twin six meter tunnels of the Glenmont line had been earlier de-signed in 1979 by URS of NYC using Jenny Engineering of Pittsburgh, Pa., as a tunnel design specialist sub consultant. Jenny had provided two alternative designs, one conventional drill and blast horseshoe and one for Tunnel Boring Machine. Funding considerations had put the design on the shelf and it was clear that the state of the art had led to improved design methods in the intervening years. Before URS was tasked to update their design in1992, the Authority reviewed its earlier hard-rock experiences in light of the funding mandate to complete each segment on a limited budget and an expedited schedule. Many factors considered and many opinions were in leading to a final decision to drop the earlier designs and redesign for a single designated means of tunneling. That method was the New Austrian Tunneling Method. The NATM had been used earlier on WMATA for both soft-ground and rock tunnels. In the public’s eyes the NATM had become inextricably linked with the use of PVC’s and filter material enveloping or partially enveloping the underground structures to give the holy grail of tunnels, a water-tight structure. Although this link of waterproofing methods with excavation and support methods was essentially severed, a general feeling of their interdependence no doubt helped lead to acceptance of the NATM decision because of the waterproofing design that accompanied it. The Authority decided to drop the TBM and conventional options and provide bid documents for NATM only. URS asked LAW Engineering of Atlanta to provide the NATM design of the tunnels and associated shafts.

Jan 1, 1997

By Kevin Bell

The TRAC™ Program was developed to provide our clients with a mechanism that allows them to better manage site remedia­tion and closure costs. This program provides a fixed-price contract for site remediation and case closure and is well suited for large pro­jects with multiple PRPs, such as Superfund sites. Because Kvaerner is a large engineering/construction firm and not a consult­ing firm, we can offer this type of contracting mechanism that envi­ronmental consulting firms are hesitant or unable to provide. With TRAC™, Kvaerner assumes financial and technical responsibilities for carrying a site through the closure process for a fixed price. Liabilities carried on our client's balance sheet for site closure can be removed when they sign up forTRAC™. In many instances, a profit can be realized as the liability on the balance sheet may exceed our TRAC™ fixed-price cost to close the site. Bonds and other sureties securing the site can be released and set­tlement with other involved parties can be quickly reached. For a project to be considered for this program, it typically meets the following criteria: 1) The project site should be physically separated from other contaminated sites 2) A reasonable quantity of site investigation data must be avail­able including site-usage history with or without a projected fea­sibility study(ies) and/or remediation design 3) Access to perform all necessary work must be available. After a review of all site data, K vaerner develops a "risk menu" to manage financial risks. In this "menu", each compo­nent of the project is assigned a level of probability that the costs will occur. Then the base cost of each activity is "weighted" by multiplying the potential cost growth by the probability. This analysis assures that the financial risks are appropriately defined, weighted, and mitigated and a realistic fixed price is developed. Upon acceptance of our proposal and conclusion of contract negotiations, Kvaerner takes over future responsibility for clos­ing your site. This allows the client to: 4) Release reserves obligated on financial statements for the site (and potentially realize a profit if the TRAC™ fixed-price cost is less than our client's booked obligation) 5) Finalize cost settlement with other responsible parties, insur­ers, etc. 6) Redirect resources involved in the environmental manage­ment of the site 7) Cap legal and administrative costs In addition to performing the site cleanup and closure work, at our client's request we are able to: 8) conclude lease obligations for property 9) dispose of equipment and buildings

Jan 1, 1998

By Steve Kral

"Gold rush" is usually associated the western United States - California, Nevada, and Colorado. The southeast section of the nation is known more for its rice, textiles, tobacco, indigo, and cotton. This area, though, is where it all began with gold in this country. The United States' first gold rush, in fact, is said to have started with the discovery of a 7.7-kg (17-1b) nugget in the Piedmont section of the Carolinas in 1799, some 50 years before the rush to California. The Carolina gold rush continued intermittently through 1942 when the Federal Government shut down all gold operations. Strong gold prices throughout the early part of this decade and new extractive technologies spurred a small resurgence of gold operations in South Carolina. Mind you, this is not Nevada with its flood of geologists and mining companies. Nor are there any 7.7 kg (17 lb) nuggets being discovered. But Ridgeway Mining Co., a joint venture between Kennecott Corp. and Galactic Resources, has set about mining 51 Mt (56 million st) of low-grade ore containing an estimated 43.5 t (1.4 million oz) of recoverable gold. The open pit, carbon-in-leach operation is located near the town of Ridgeway in South Carolina, about 32 km (20 miles) north of Columbia. Carolina gold North and east of Ridgeway, Piedmont Mining Co. operates the historic Haile gold mine near Kershaw, SC. And Brewer Mining Co. operates the nearby Brewer deposit. Between 1829 and 1942, South Carolina gold mines produced 10 t (318,800 oz) of gold. It all began in 1799 when Conrad Reed, son of a German immigrant farmer, found the 7.7 kg (17 lb) nugget in Little Meadow Creek, NC. His father thought the rock was worthless and used it as a doorstop, so the story goes. It took nearly three years before Conrad's father decided his doorstop was indeed gold. Gold was later discovered in the Greenville district of South Carolina. And, in 1828, Benjamin Haile discovered gold in a stream that ran through his property in Lancaster County, SC. Haile's mine became South Carolina's most famous and most productive gold mine, producing more than 7.8 t (250,000 oz). At first, miners worked the stream beds of Haile's property. Later, lode deposits were discovered on slopes alongside the creeks. They would lease 4.6 ml (50 sq ft) lots and mine as deep as 7.6 m (25 ft). During the Civil War, the Confeder-

Jan 1, 1989

By A. Dale Wunderlich

Introduction Loss prevention programs have become absolutely necessary at any precious metals producing property. In the past eight years, one security company, specializing in precious metals mine, mill, and refinery security, has been involved in investigations at gold and silver properties that have resulted in 62 criminal convictions. Of those, all but five were employees, former employees, contract employees, or vendors for the company. Several of the cases involved losses of more than $1 million. The largest number of employees prosecuted from one investigation was 17. A recent case resulted in 12 criminal prosecutions and, several years ago, one involved an additional 12 criminal prosecutions. The most serious theft problem facing precious metals mines is employee theft. Is is estimated that 95% of the dollar losses from precious metals thefts can be attributed to employees. This does not mean there is no robbery or burglary exposure. There have been successful robberies, burglaries, and extortion cases. Most mining companies, though, provide better protection against external theft than from internal theft. That is one reason employee theft has reached epidemic proportions. Any product can be stolen No product is immune to theft. Precious metals investigations have involved the theft of high grade ore, dore, bullion, concentrates, precipitates, loaded steel wool, loaded carbon, and sump cleanup. Over a period of several years, this author's security agency has documented the theft of more than 22.5 t (25 st) of load carbon. Most mining companies do not protect the number one adsorption tank or the loaded carbon screens, which frequently leads to losses. Precipitates, electrowinning tank sludge, sump material, and concentrates are usually afforded lit¬tle protection because mine management believes it is too difficult to process. There are custom mills throughout the United States that will process any form of precious metals with no questions asked. This has become a particular problem since the certificate of ownership requirement has been eliminated by most states. Due to the large number of gold mines coming on line, many mine managers are being recruited from base metal mines, where primary security problems involve the theft of tools and company property. These managers do not understand the unique security problems associated with precious metals production. Consequently, they usually forego many security needs in the interest of economy. Unfortunately, numerous cases are on file where mining companies have suffered large losses because their physical security and their security procedures were not adequately addressed when the property was in its planning stages. Properly designed and appropriate equipment The most economical time to plan alarm/closed-circuit televi-

Jan 4, 1988

By Richard F. McFarlin

INTRODUCTION Phosphate, one of the three major elements essential for all living plants and animals, has been mined in Florida for over a hundred years. Comprising roughly 80% of the U.S. total and 25% of the world's supply, the bulk of the 35 to 40 million annual ton output is converted to chemical fertilizers. With the exception of one mine in north Florida near the Georgia state line, today's mining activities are centered in the middle of the peninsula just east/southeast of Tampa in Polk, Hillsborough and Hardee counties. These "bone valley" deposits extend into Manatee and DeSoto counties, but there is little active mining there as yet. Because strip mining is, perhaps, the ultimate environmental insult and because Florida has a proactive environmental community, it is not surprising that the mining of phosphate rock has become increasingly controversial. This paper describes how phosphate rock is currently mined, the environmental problems presented by mining and processing the rock, and some mitigating technologies being employed to answer such problems. THE PHOSPHATE DEPOSIT AND ITS EXTRACTION Florida's phosphate deposits containing the calcium phosphate mineral, carbonate-fluorapatite, are between ten and fifteen million years old. The typical "bone valley" matrix is 15 feet thick and lies under 20 to 30 feet of overburden.(Fig. 1) Both the sandy overburden and matrix are unconsolidated and can be removed with standard 45 to 65 cubic yard, walking electric draglines. After removing the overburden, which is windrowed nearby, the dragline operator casts the matrix into a "slurry" pit where it is broken up by high pressure water monitors. Pit pumps (with boosters where necessary) transport the matrix slurry through 16 to 20 inch pipelines to a washer where the three components of the matrix (sand, clay and apatite) are separated. The phosphates contained in central Florida matrix are approximately half pebble/half flotation feed, through the pebble ratio decreases as the industry mines southward. Again, the matrix is roughly equally divided among sand, clays and apatite. The phosphatic clays, 75% of which are less than one micron in size, leave the washer as a 3 to 5% colloidal suspension. The impoundment of these waste clays is one of the environmental challenges to be discussed later. The sand (silica) is separated from the similarly sized phosphate particles by a double float process (fatty acid followed by a reverse mine or cleaner float), and the sand tailings are then pumped to disposal or reclamation sites. The apatite flotation product is combined with the screened phosphate pebbles and stacked to dewater before shipping.

Jan 1, 1992

By F. Touboul, M. Thiercelin, K. BenNaceur

Introduction The need to develop accurate predictive hydraulic fracturing simulators arises from the consideration of vertical containment for the fracture. Fracture height growth from a pay zone into adjacent layers has been shown (see Cleary [I]) to depend on three sets of parameters for the different strata: - elastic properties, - closure stress variations, and, -fracturing fluid leak off, and poro-elastic stresses. Qualitative analysis of the effects of these parameters has been reported in the literature. The first effects were described by Van Eekelen, using simple elasticity considerations [2]. The effect of stress variations was described numerically by Simonson and a1. [3] and experimentally by Thiercelin [4]. Effects of back stresses induced by fluid invasion on fracture propagation were considered by Cleary [5]. In order to couple these effects, a numerical code al- lowing the simulation of three dimensional growth of a hydraulically induced fracture has been developed with the ability of representing the effects of heterogeneities on fracture lateral and vertical extension. The model is based on a new variational formulation of the boundary integral representation of three-dimensional elasticity. The fluid flow and elasticity equations are solved using a moving mesh representation which offers enough flexibility to enable the simulation of any closure stress distribution. Simpler models representing fracture height growth (P3DH models) have been developed [6] [7] that approximate the fracture by a series of one dimensional segments, and the limitation of such approaches is examined in this paper. 1 Description of the model 1.1 Fracture Geometry Hydraulic fracturing simulations involve the coupling of solutions to elastic deformations, fluid flow in the fracture, and fluid leak off into the formation. Since the use of direct solution techniques (i,e,,3D finite elements) is prohibitive, the method used in this study is baaed on a boundary integral representation of the 3D elasticity equations. 1.2 3D Models The classical representation of the problem of a fracture in an infinite medium by boundary integrals is [8]: [ ] where u is the unknown displacement field, r n is the traction operator, I? is the fracture surface, and K is the Kelvin tensor of fundamental solutions to the elasticity operator. Using the notation: [ ] for the displacement discontinuity (or fracture width), one can attempt to solve the boundary integral relation using surface integrals (91 or the displacement discontinuity technique, first introduced by Crouch [lo], and extended to three-dimensional problems [Ill. However, numerical problems arise since the Kelvin tensor has a singularity in

Jan 1, 1986

By Rebecca S. Stanevich

BACKGROUND Diesel exhaust is an animal carcinogen, although evidence of the carcinogenicity in humans is "limited". (World Health Org. , 1989) Of the eight cohort studies in the 19808, five found an increased risk for lung cancer among workers who may have been exposed to diesel exhaust (RR from 1.3-1.5, SMR from 101-132). (Howe, et al., 1983) Only two studies accounted for smoking indirectly. Of the ten case-control studies in the 1980's, eight reported increased risk of lung cancer among those populations purportedly exposed to diesel exhaust. (Benhamou, et al. , 1988) All but one of these adjusted for smoking and other occupational exposures. The odds ratios ranged from 1.2 to 2.1. In two of these studies, miners experienced a two to three fold risk. (Benhamou, et al., 1988) Bladder cancer has also been linked to diesel exhaust in cohort and case-control studies. Excesses of approximately 50% were observed among truck drivers in studies by NCI. (Hoar, et al., 1985) In the National Bladder Cancer Study, risks for truck drivers rose with duration of employment. A study by NIOSH in Ohio also found an excess of bladder cancer among truck drivers, particularly among those with 20 or more years of employment. (Steenland, et al, 1987) Despite the large number of studies in which the relation between diesel exhaust exposure and lung cancer has been examined, exposure to diesel exhaust has been quantitatively estimated only in the studies of railroad workers and truck drivers. (Woskie, et al., 1988) The excess lung cancer risk experienced by workers in these two occupational groups was modest, ranging from 40 to 90% for those with long-term employment. However, diesel exhaust exposure among railroad workers and truck drivers is lower than that seen among miners. Several markers of diesel exhaust have been utilized in these studies. Diesel exhaust is a complex mixture of particulates, vapors and gases. One group of these gases, the nitrogen oxides, react with polynuclear aromatic hydrocarbons, forming mutagenic and possible carcinogenic nitrated derivatives. (World Health Organization, 1989) For this reason, and because it is easy to measure and analyze, NO, was frequently used as a marker of diesel exhaust exposure. As part of the Garshick (Garshick, et al., 1988) study of railroad workers, Woskie measured NO, exposures of 477 railroad workers. (Woskie, et al., 1988) Geometric mean exposures of 13 job groups ranged from 12 to 80 ppb. In a New Mexico potash mine, (Attfield, et al. , 1982) exposures of from 100 to 3300 ppb nitrogen dioxide

Jan 1, 1992

By William H. Mount

INTRODUCTION Effective mine ventilation is required to maintain a healthy underground environment for humans. Without effective ventilation, the environment can become unhealthy or hazardous as a result of the depletion of oxygen, contamination with toxic gases, or the buildup of an excessive amount of particulate matter (dust). Each contaminant has an upper limit of concentration that should not be exceeded within an 8-hr period. This is known as the threshold limit value (TLV). The TLV represents an acceptable level of exposure that should produce no ill effects. Unfortunately, more than one contaminant may be present at any one time and the effects of the individual contaminants may be additive, i.e., the effects of each contaminant must be considered simultaneously to determine the potential danger to miners. Possibly the greatest threat to mine-air quality is the uncontrolled underground use of the diesel engine. The diesel engine was invented in 1892 by Rudolf Diesel. His intention was to develop a power source that could burn coal dust as a fuel, but he was unsuccessful in that attempt and had to resort to liquid petroleum fuels (Johnson, 1975). In 1898, the diesel engine was intro¬duced into the United States by Adolphus Busch, who anticipated using it as a prime mover in factories and generating plants. At that time, the diesel engine was a very large and very heavy engine, designed for fixed installations. By 1919, lighter engines were being developed, and by 1931, Caterpillar was marketing a diesel-powered, track-type tractor (Henderson, 1975). Since 1931, the diesel engine has evolved into an extremely popular prime mover in medium and heavy-duty applications. Efficiencies now are on the order of 40% and improvements such as turbocharging and aftercooling have produced engines capable of generating power at a ratio of 0.3 kW/kg (1.0 hp per 5.0 lb) of engine weight. Although the diesel engine is relatively efficient as a mobile power plant, it is far from efficient in terms of the energy produced from the energy potential of the fuel. About 60% of the heat value of the fuel leaves the engine as wasted heat, with about 50% of that heat being emitted through the exhaust pipe and the other 50% being emitted through the radiator or cooling fins. Perfect combustion in an engine would produce only water vapor (H_0), carbon dioxide (CO_), and nitro¬gen (N2) as the byproducts. Since the diesel is not a perfect engine, each pound of fuel burned generates 5.6 m° (200 cu ft) of exhaust gas, containing about 0.009 m3 (0.33 cu ft) of carbon monoxide (CO), 0.009 m' (0.33 cu ft) of nitrogen oxides (NO, NO2, and NOD), and 0.57 m3 (20 cu ft) of carbon dioxide. The balance of the exhaust emission consists of free nitrogen and water vapor (Hurn, 1975). Contrary to popular belief, the diesel is not inherently dirty. Under normal operating conditions, a well-maintained engine neither smokes nor smells. However, the same well-maintained engine can and does produce toxic emissions. A diesel engine is not inherently safe and constitutes a distinct hazard to personnel. This chapter is devoted to a description of the various toxic substances that may be generated by a diesel engine. Although some of these substances may also be produced by blasting or natural causes, the focus of this chapter is on the relationship between the internal- combustion compression-ignition engine (the diesel) and the quality of the mine air. CARBON MONOXIDE Combustion Process During the combustion process (burning) of organic fuels, each atom of carbon combines with two atoms of oxygen, provided that a surplus of oxygen atoms is available. Thus, the carbon is oxidized to carbon dioxide. Most open flames, such as trash fires, camp fires, gas ranges, etc., produce carbon dioxide. However, with insufficient oxygen, incomplete combustion results as the carbon atoms each combine with one atom of oxygen to produce toxic carbon monoxide. Burning charcoal briquettes produce carbon monoxide because the combustion takes place inside the briquettes where sufficient oxygen is not available to the combustion process. Internal-combustion engines, whether burning gasoline or diesel fuel, also produce carbon monoxide. The only oxygen available to the combustion process is that trapped within the cylinder. If the amount of fuel delivered to the cylinder is excessive, there is insufficient oxygen for complete combustion and carbon monoxide production results. In a normally aspirated (nonturbocharged) diesel engine, the amount of air "sucked" into a cylinder is the same on every intake stroke, resulting in complete combustion only at low levels of engine loading, when small amounts of fuel are injected. Higher levels of engine loading cause larger amounts of fuel to be injected into the same volume of air in the cylinder. Unless the volume of air is increased, the combustion process becomes progressively less complete as the amount of fuel increases. Turbocharged engines are able to compensate some¬what for increased loading and increased fuel consumption. The turbocharger acts as a compressor for the intake air, forcing a larger volume of air into the cylinders as the engine speed increases. Hence the turbocharged engine burns cleaner than a naturally aspirated engine and produces slightly less carbon monoxide (Marshall and Fleming, 1971). Much of the underground equipment used today is powered by turbocharged indirect-injection diesel engines. Although these engines emit fewer toxic contaminants than naturally aspirated engines, they do not eliminate the problem. Since the turbocharger is driven by the exhaust gases, rapid accelerations can cause temporary overfueling of the engine until the turbocharger attains a speed sufficient to restore the correct air-to-fuel ratio. During this "turbocharger lag," the combustion cylinders contain insufficient oxygen, causing severe smoking and an increased output of carbon monoxide.

Jan 1, 1982

By Rudolf Kvapil

INTRODUCTION Sublevel mining is a mass mining method based upon the utilization of gravity flow of the blasted ore and the caved overlying waste rock mass. As with any other mining method, sublevel caving has advantages and dis¬advantages which must be carefully considered and evaluated. The major advantages of sublevel caving are dis¬cussed as follows: Because all of the mining activities are executed in or from relatively small openings, sublevel caving is one of the safest mining methods. Drifts, which are the pri¬mary working places, are distributed in a uniform pat¬tern on all levels. Normally the maximum dimensions of the sublevel drifts are about 5 m wide and 3.7 m high. The transportation drifts can have the same section, or the height may be increased to about 4.5 m when trucks are loaded in the transport drifts. The stability and safety of such drifts in competent rock can be easily controlled by smooth blasting or by a combination of smooth blasting with shotcreting. In less competent rock masses, stability can be achieved by combined reinforc¬ing, for example, by a combination of smooth blasting, shotcreting, and rockbolting. The major mining activities can be broken down into three groups: drifting and reinforcing; ore fragmenta¬tion, i.e., production drilling and blasting; and ore draw¬ing, loading, and transportation, and all are relatively simple. Because of the repetitive nature of the mining system, one can standardize almost completely all min¬ing activities. This means that a high degree of work efficiency can be achieved. Because the components of mining production in sublevel caving can be standardized, a high degree of mechanization is possible. In modern sublevel caving the sections of drifts and tunnels are sufficiently large to allow the introduction of large trackless mining equip¬ment. The advantages of a trackless system can be then broadly utilized not only for direct mining but also for all services, including the transportation of mining per¬sonnel to the working place. The flexibility of mining is very good. Standardiza¬tion and specialization of mining activities and equip¬ment on separate levels (lower level or levels in de¬velopment, upper level or levels in production mining) together with the trackless system yield a high degree of flexibility. This allows a rapid start-up of mining and good flexibility in making production rate changes. The method lends itself to good work concentration, organization, and working conditions. Normally, on the lower levels, various phases of development are under¬way. Upper levels are in various stages of extraction. Therefore the work can be easily organized into a sys¬tem which excludes interference between mining activi¬ties. Safety of mining (in small dimension openings), good work organization, high mechanization using large modern mining equipment, etc., comprise very good working conditions. Naturally such a system enables a high work concentration and rationalization of separate specialized mining activities and therefore mining by sublevel caving can be effective and relatively in¬expensive. The major disadvantages of sublevel caving, on the other hand, are: There is a relatively high dilution of the ore by caved waste. Various types of ore loss can occur. When the ex¬traction limit (that point yielding the maximum accept¬able amount of dilution) is reached, the remaining highly diluted ore represents an ore loss. Some ore is lost in passive zones located on the level of extraction between the active zones of the gravity flow. Part of the ore from these passive zones can be recovered together with ore extraction on the lower sublevel, but some un¬diluted and often not fragmented ore located in passive zones above the plane of the footwall is lost. In gen¬eral, these losses are larger as the inclination of the ore body and the footwall is reduced. A relatively large amount of development is re¬quired. This includes transport drifts, usually located in the footwall waste rock on each sublevel, and sub¬level drifts, which connect the active mining areas to the transport drifts and as a result are partially in ore and partially in the waste rock of the footwall. The waste rock length increases as the inclination of the ore body and footwall decreases. It also includes orepasses, used for transport of the ore or waste from the separate sublevels downward to the main haulage level, and normally driven in waste; and inclined drifts or tunnels, which provide a connection for the trackless equipment between the main haulage level and the separate sublevels and are driven in waste. Finally there is the de¬struction of the surface through subsidence. To maximize the ore recovery, minimize the dilu¬tion, and achieve a high efficiency of mining by sub¬level caving, good data regarding the gravity flow pa¬rameters for the blasted ore and the caved waste are of utmost importance. The exact type and amount of data required depend upon the purpose and needs of the study. For the first feasibility study, it may be sufficient to utilize the data from other sublevel caving operations with similar conditions and circumstances. For any higher level of mine planning it is clear that more exact data, including analytical and experimental analyses up to full-scale in-situ testing, are necessary. Basic gravity flow principles and design guidelines for the application of the sublevel caving mining method are presented in the following sections. Although some¬what simplified, they should provide a basis for mine planning and operation. The gravity flow principles described can be effectively applied to other mining situations, with some modification. Also, steep dipping coal seams can be effectively mined by modified sub¬level caving.

Jan 1, 1982

By C. Alan Tapp

Introduction Mine sampling determines the practicality of any mining operation. Improper sampling can result in an incorrect appraisal of present production and future potential. Therefore, the mine department in charge of ore-reserve calculations and mine sampling should be overseen by competent and experienced professionals with technical backgrounds qualifying them to produce accurate results. Sampling is a process by which portions of an ore body are collected and analyzed to estimate the average mineral content of the entire ore body. It is incorrect to assume that a large number of samples eliminates any errors in the sampling method. To obtain unbiased samples, proper sample location with respect to rock type and mineralization is just as important. The sampling procedure must yield correct results for the type of mineral deposit, and careful consideration should be given to whether or not the sampling technique has been developed to an extent sufficient to eliminate as much human error and bias as possible. Only after the ore has been mined and milled is the sampling accuracy known. Sampling also provides information about the bulk composition of the ore for mineralogical and metallurgical tests that determine the economic ore-waste boundaries and the geologic trends for exploration. Actual mining plans can be developed from this information to maximize profits. Accurate sampling is critical, and thus must be approached in a scientific manner. Sampling Techniques Sampling practices and techniques are as varied as the mines in which they are used. The method(s) chosen must be tailored to suit the company and mining needs. For instance, tabular uranium deposits, vein gold deposits, and porphyry copper deposits pose special problems in conducting unbiased sampling. The mine geologist or engineer in charge must develop a sampling method, test it in a sample area, and then critically evaluate the results. If the results from the test area are accurate within the economic limits established by the company, they then may be adopted for general use in the mine. Four routine sampling methods are suitable for specific sampling objectives in the daily mine routine: (1) channel sampling, (2) chip sampling, (3) grab sampling, and (4) bulk sampling. The final sampling results depend upon how the four methods are combined to accurately determine the grade of the ore body. When used in conjunction with each other during different stages of mine development, the channel, chip, grab, and bulk sampling methods provide an in-house check or a comparison by which mining methods and sampling procedures can be evaluated. However, the most valid check is based upon the daily mill production. Channel Sampling Channel samples consist of cuttings collected from a groove cut into the rock about 102 mm (4 in.) wide and 19 mm (0.75 in.) deep. Various tools ranging from a 1.8-kg (4-lb) hammer and moil to a pneumatic chisel can be used to cut the sample. Accessibility and rock hardness determine the applicable sampling tools. Before attempting to take a sample, the rock surface must be cleaned thoroughly; the method of cleaning depends upon the amount of mine dust accumulated on the surface or the degree of alteration of the rock surface. Typical cleaning methods 'employ a wire brush, water, or chipping a fresh surface. Next, the sample outline is marked on the prepared surface, taking care to choose appropriate sample loca- tions. After determining the proper sample outline and length, the sample can be chiseled out, catching the rock fragments on a canvas tarpaulin on the floor, in a powder box, in a canvas bag to avoid contamination, or by some other suitable means to capture all of the sample. Vertical veins present a special problem because the drift's back usually is arched, not square. For example, Fig. 1 shows that if sample intervals are measured from A' to D', the length of the sample interval is greater than the true vein width, resulting in an incorrect calculation of the ore reserves. The correct method would collect three samples at A'-B', B'-C', and C'-D', using either actual measurements in the mine represented by A-B, B-C, and C-D or trigonometric calculations to determine the true ore thickness. Then, each sample can be weighted by grade and true thickness for the vein. Channel lengths usually are a maximum of 1.5 m (5 ft), and it is good practice to divide longer samples into smaller intervals according to structures, changes in rock types, or differences in rock hardnesses. The influence of those features on the mineralization then can be determined. Chip Sampling Chip sampling is a variation of channel sampling used when the rock is too hard to channel sample economically or when little variation in the mineral content indicates that this sampling method will yield results similar to those of channel sampling. Rather than cutting a channel in the rock, small chips are flaked off at regular intervals over the entire face or area being the mine. sampled. Care must be taken to assure that the sample is representative of variations in the rock hardness and type. hi^ method is fast and useful in preliminary evaluations, but it should not be used for quantitative ore-reserve calculations. Grab Sampling Grab sampling is a fast method for double checking either channel or chip-sampling procedures, and, in some instances, mine production can be estimated from carefully taken grab samples. Grab sampling takes equal amounts of material at selected intervals over a mine dump, a muck pile, or from an ore car to estimate its Channel Sampling mineral content. Generally, this method is not considered reliable. Many independent variables can affect this type of sampling process. Thus, if the ore occurs in the softer fraction and a proportional amount of the result-

Jan 1, 1982

By W. J. Schlitt

Introduction Heap and dump leaching are low-cost metal production techniques that are gaining in popularity among gold and copper producers. However, the flow of solution in heaps and dumps has received little attention in the literature. This is unfortunate since solution flow is one of the few parameters subject to operator control. Thus, solution management may well influence both operating costs and plant performance. Costs aside, there are two important aspects of solution flow to be considered -the metallurgical and the hydrological. Some of the metallurgical factors have recently been discussed (Jackson and Ream, 1980; Schlitt, 1984; Schlitt and Nicolai, 1987). These cover solution application rates and methods, irrigation rates, leach-rest cycles, and nonvertical solution flow. According to Caldwell and Moss (1985), however, the hydrological aspects may be more significant than the metallurgical ones. In particular, a phreatic surface will form when excessive flow leads to an accumulation of water and the associated buildup of pore pressure within the rock pile. Such internal flooding can either originate at the foundation or at some other zone of very low permeability. The latter condition gives rise to an impounded volume of solution, i.e., a perched water table (see Whiting, 1985). Caldwell and Moss point out that a rising zone of saturation is probably the most common cause of dump failures. Of course, such failures have even occurred in heaps that were carefully prepared for leaching (Milligan and Engelhardt, 1984). Thus, flooded conditions and perched water tables represent an important safety consideration as well as having an impact on metallurgical performance. The following sections describe a case history in which a perched water table developed within a copper leach dump. The description includes background information, solution flow rates, and metallurgical data. Then this situation is compared to one involving normal drainage. Description of the leach system The leach dump in the case history is located at a shutdown open pit copper mine. It was built in two lifts, with the second added some 20 years after the first. There is little detailed information available on the initial lift. It was built with rail¬hauled waste and was generally less than 30 m (100 ft) high at the crest. The area available for leaching was about 120 m (400 ft) wide and more than 380 m (1250 ft) long. The dump surface was prepared for leaching by dozing ponds approximately 12 m by 12 m by 2.5 to 3.0 m deep (40 ft by 40 ft by 8 to 10 ft). The ponds were leached by flooding with barren leach solution returned from a scrap iron cementation plant. Based on mill feed at the time, the average waste grade was probably close to 0.4% Cu. The first lift leached well. It accepted high flows, which together with the waste grade, produced a rich pregnant leach solution (PLS). Old records indicate a PLS of "50 lb Cu/ 1000 gal," or about 6 g/L. As later drilling would indicate, such a high tenor led to dissolution of considerable scrap iron that was returned to the dump. The iron then hydrolyzed and settled out on the pond bottoms. In addition, the waste settled substantially so that the unleached crest was 3.0 to 4.5 m (10 to 15 ft) above the ponded area. Eventually, the leachable copper was extracted and the dump became less permeable. Thus, the PLS tenor dropped until it became uneconomical. About ten years later, mining resumed and the decision was made to add another lift to the dump. This was done without giving much thought to a subsequent leach operation. Hence a 24-m (80-ft) lift was built on top of the original dump. The surface of the latter was not prepared in any way, e.g., by leveling and/or deep ripping, prior to over-dumping. Examination of subsequent drill cuttings indicated that the new lift contained about 0.2% Cu, with chalcopyrite and chalcocite (50:50) being the predominant copper minerals. Most of the chalcocite occurred as rimming on the abundant pyrite, with the pyrite to chalcopyrite ratio estimated at 10 to 1. The use of 100- and 120-ton trucks for haulage caused some waste compaction during emplacement. In addition, the host rock itself was relatively soft, being a porphyry intrusive material that was partially altered to clay. As a result of the initial compaction and clay swelling, the rate of water percolation from the new leach ponds was slow and the ponds often contained considerable standing water. Even frequent ripping failed to provide a sustained improvement in the percolation rate. The poor surface permeability was exacerbated by hydrolysis of iron salts which settled as a layer on the pond bottoms. Partly as a result of the permeability problems, metallurgical performance was not up to expectations. These had been based on laboratory tests which showed about 20% copper solubilization in two weeks. Continued copper extraction in the tests also suggested that a substantial percentage of the copper would eventually be recovered. However, the PLS grade in the actual operation peaked briefly at about 0.48 g/L Cu (4 lb Cu/1000 gal), then declined to a range of only 0.24 to 0.36 g/L Cu (2 to 3 lb Cu/1000 gal). The poor leaching was traced to a lack of oxidation of the sulfides. There were two principal observations supporting this conclusion. First, there was no evidence of any heat being generated within the dump. As discussed elsewhere (Schlitt and Jackson, 1981; Hiskey and Schlitt, 1982), pyrite oxidation is quite exothermic and the high pyrite content of the waste should have led to an increase in the temperature of the leach solution as it percolated through the rock pile. Second, there was no sign of any natural convective air flow through the dump.

Jan 1, 1987

By William Hustrulid

INTRODUCTION The Idarado mine lies high in the San Juan Moun¬tains on the divide between the Uncompahgre and San Miguel Rivers and consists of a consolidation of a number of old and prominent mining properties through which course some famous and very produc¬tive veins. Among the better known are the Smuggler, Tomboy, Montana-Argentine, Black Bear, Liberty Bell, Virginius, Flat, Barstow, and Japan, as well as many others. Most of these veins have been extensively mined over the past century and in the last three decades the Montana-Argentine and Black Bear veins have been the backbone of the Idarado mine; therefore, the descrip¬tion of the veins is limited to them. Access to the mine is through either the Treasury tunnel, whose portal is below Red Mountain Pass on US Highway 550 at an elevation of 3244 m (10,643 ft), or the Mill Level tunnel entrance 3.2 km (2 miles) east of Telluride, CO, at an elevation of 2761 m (9060 ft). The Treasury tunnel intersects the Black Bear vein 2643 m (8670 ft) from the portal and the Mill Level tunnel intersects the Argentine vein 2179 m (7150 ft) from the portal. Mining is by shrinkage stoping from slusher sublevels. The size of the scope blocks varies somewhat, but the standard size is 67 to 76 m (220 to 250 ft) long and 61 to 76 m (200 to 250 ft) high. The mine ranks either first or second in Colorado in yearly production of gold, silver, copper, lead, and zinc. It is 9.6 km (6 miles) from the Red Mountain plant to the Pandora plant, via interconnecting drifts and raises. There are engineering offices at both plants as a matter of convenience. The Red Mountain plant in¬cludes the company general offices, warehouse, carpen¬ter and machine shops, and mine change room. The Pandora plant consists of the mill and assay office, ma¬chine shops, and mine change room. The flotation mill has a capacity of 1632 t/d (1800 stpd), making a bul¬lion product and separate concentrates of lead, copper, and zinc. HISTORY OF THE MINE The Montana-Argentine vein was first extensively worked by the Tomboy Gold Mines Co., Ltd., a British concern. This company mined the stoped areas above the Ophir level between 1910 and the late 1920s and most of the stoped areas above the 2100 level between 1900 and the late 1920s. Gold was the principal ore metal mined. The area between the Revenue and Ophir levels was mined chiefly by the Revenue Mines Co. between 1900 and 1910. The ore was worked from the Revenue tun¬nel, which portals in Canyon Creek. Gold and silver were the chief metals recovered. The stopes between the 1700 and Revenue levels, as well as some higher stopes, were mined by Telluride Mines Inc. during the 1940s. The Mill Level tunnel was driven by that company from 1945 to 1948. Lead and zinc then became economically more important than the precious metals. In 1953, Idarado purchased Telluride Mines, which merged with the parent company in 1956. The Black Bear vein was first extensively worked by the Black Bear Mining Co. in the 1900s and by the Colorado Superior Mining Co. from about 1914 until snowslides at the mine camp [altitude 3750 m (12,300 ft)] terminated the company's operations in 1924. Leasers operated at intervals until 1934. The Treasury tunnel, formerly the Hammond tunnel, had been started before 1900 and reached the 1646-m (5400-ft) mark early in the 1900s, at which time activity lagged until the late 1930s. In the early 1940s, Idarado extended the Treasury tunnel from its heading at 1646 m (5400 ft) to the Black Bear vein and established a raise connec¬tion with the 600 level, the lowest level in the old mine. Since completion of initial work in the mid-1940s, systematic development of the mine, both in the driv¬ing of new headings and the utilization of older open¬ings, has resulted in the present extensive network of workings. GEOLOGY Introduction The oldest rocks of the area are the Precambrian metamorphic rocks, the Uncompahgre formation which are massive quartzites, some phyllites and slates, and dolomitic or limestone beds. West-dipping Paleozoic and Mesozoic strata lie on the Uncompahgre formation. These units are separated by a major angular uncomformity from overlying, essentially horizontal, Tertiary formations that include the basal Telluride conglomerate and several thousand feet of overlying volcanic rock. Intrusive rocks, mostly Tertiary in age, are common in the area, and are in the form of dikes, stocks, and sills. Dikes are very closely associated with some of the ore veins (Mayer). Description of Veins The Black Bear and Argentine veins range from 0.6 to 7.6 m (2 to 25 ft) in width, but in most places are 1.5 to 2 m (5 to 7 ft) wide. They vary in character from a well-defined tabular structure between sharp "frozen" walls, or gouge seams, to an irregular zone of quartz and quartz-sulfide stringers. Many gouge seams within the veins make the veins blocky and loose. Common gangue minerals in the veins include quartz, pyrite, rhodonite, chlorite, sericite, clay minerals, epidote, calcite, adularia, rhodocrosite, fluorite, and specularite. Quartz constitutes 60 to 70% of the veins and varies widely in character, ranging in color from clear through white, gray, and green, to amethyst. Chlorite, sericite, the clay minerals, and fine-grained quartz are common alteration products of the vein walls and of wall rock fragments in the veins. Epidote is an altera¬tion of the dike or, less commonly, of tuff-breccia. Calcite, adularia, fluorite, and rhodocrosite, which are wide¬

Jan 1, 1982

By J. R. Johnson, C. G. Stewart, D. K. Myers

INTRODUCTION Radon-222 is an inert, radioactive gas formed by the radioactive decay of radium-226, a long-lived member of the uranium-238 decay chain. Radium is present in varying amounts in virtually all soils and, on the average, about 36,000 pCi (1330 Bq) of radon per square meter of soil diffuse into the atmosphere each day (UN 1977). Radon decays with a half-life of 3.6 days through four short-lived daughters to lead210 and it is these short-lived daughters[ [Ra A, (218Po, t, = 3.0 min) , Ra B, (214 Pb, t;, = 27 min), Ra C, (214Bi, t] = 20 min) and Ra C1 (214Po, t] = 2.5 x 10-6 min)] ]which cause the major health hazard associated with radon (Bale 1951). Atoms of these daughters, either unattached or attached to the ever-present particles in air, are deposited on the surfaces of the respiratory tract; alpha particles emitted in their decay can result in large doses to the cells of the bronchial epithelium lining the respiratory tract. These daughters will be present in air in varying relative concentrations depending on the "age" of the air (time since radon emanated into it) and on the amount of mixing of radon and radon daughter contaminated air with clean air. [The practical unit developed to quantify the amount of radon daughters in air is the Working Level (WL). This unit was historically related to the equilibrium concentration of 100 pCi (3.7 Bq) of the short-lived daughters of radon in one liter of air (cf. Holaday 1969) and is defined as any mixture of the short-lived daughters in a liter of air that have a-potential alpha energy of 1.3 x 105 Mev (2.08 x 10-5J) in their decay to lead-210. The working level month (WLM) was developed along with the WL, and was defined as an exposure to one WL for a working month (170 h). This is equivalent to 2.2 x 107 MeV•h•L-1 (3.54 x 10-3 J.h.m-3). If the average breathing rate is taken as 1.2 m3.h•1 (ICRP 1975), then one WLM is equivalent to inhalation of 4.24 mJ of potential alpha energy.] It is now generally agreed that the inhalation of radon daughters is the major potential radiation hazard in uranium mining, and contributes a substantial fraction to the natural radiation exposure of the general population due to the accumulation of radon and radon daughters from natural sources in buildings. Radon daughter concentrations in modern mines are controlled by ventilation, and by blocking off old working areas (cf. Simpson, 1959). However, before the hazard from radon daughters was recognized, considerably higher concentrations of radon daughters were present in some uranium and non-uranium mines. These high radon daughter concentrations resulted in an increase in lung cancers in the mining population, and it is these results that are our main source of information on the risk of inhaling radon daughters. HISTORICAL REVIEW Many excellent reviews of the history of understanding the health effects of inhalation of radon daughters are available (see, for example, Hueper 1942, Lorenz 1944, Sikl 1950, Stewart 1964, Holaday 1969, Lundin 1971, Cross 1979) but a brief summary of some of the highlights in this area may be of interest. [a] 1556: Agricola describes an unusual and fatal chest disease occurring among underground miners in the region of Schneeberg and Joachimsthal (Jachymov) in the Erz mountains in Central Europe. (It is of some historical interest to note that Agricola's book was translated from Latin into English by a mining engineer and his wife; the engineer later became President of the U.S.A.) [b] 1879: Haerting and Hesse indicated that the majority of deaths among Schneeberg miners were due to lung cancer; the lung cancers in these miners (who were incidentally not cigarette smokers) were observed twenty to fifty years after they began working in the mines. [c] 1896: Discovery of natural radioactivity by Becquerel, followed by discovery of radon by Dorn in 1900. [d] 1924: Ludewig and Lorenser report high concentrations (400 - 15000 pCi or 15 - 570 Bq per liter) of radon in the air in the Schneeberg mines and suggest that radon could be responsible for the high rate of lung cancer among miners. However, the reason why radon should cause lung cancer specifically was still not really understood up to twenty years later (Lorenz 1944). High concentrations of radon in the air in the Joachimsthal mines were reported by Behounek in 1927 and a high incidence of lung cancer among Joachimsthal miners (similar to that among miners at Schneeberg, which is only some 30 km distant but in a different political district) was noted at about the same time (Sikl 1930; cf. Sikl 1950). It is estimated that about half of the Joachimsthal miners died from lung cancer and about half from silicosis and tuberculosis (Sikl 1950). [e] 1930's and 1940's: Radioactive ores are deliberately mined in the U.S.A., Canada and other countries primarily as a source of radium for medical purposes and for luminescent dials; other radioactive ores are mined as a source of several non-radioactive minerals, while extensive uranium mining did not begin until the late 1940's. [f] 1940: Based on crude epidemiology and dose calculations, Evans and Goodman propose 10 pCi L-1 as a maximum permissible concentration of radon in continued human exposure. This is the first known recommended maximum permissible concentration for radon. This recommendation was adopted by the U.S. National Bureau of Standards in 1941 and reconfirmed in 1953. [g] 1945: Mitchell identifies the short-lived daughters in radon as a likely cause of the increased lung cancers in the Schneeberg-Joachimsthal miners

Jan 1, 1981