Search Documents

By G. Robert Moorehead, Peter T. Luckie, Harold L. Lovell, David J. Akers, James K. Kindig

Jigging is a process of particle stratification in which the particle re- arrangement results from an alternate expansion and compaction of a bed of particles by pulsating fluid flow. The vertical direction of fluid flow is reversed periodically. The rearrangement results in layers of particles that are arranged by increasing density from top to bottom of the bed. This response, developed from the many and continuously varying forces acting upon the particles, permits a solid-solid separation more related to particle density and less to particle size than any other "hydraulic-type" process. The stratification is usually carried out in a rectangular, open-top container called a jig, in which the mass of particles (termed a "bed") is supported on a perforated base through which the water flows in alternating directions. The coal particles, in addition to the vertically expanded and compacted bed motion, move continuously, horizontally across the supporting screen. Following the particle stratification, the particle bed is physically "cut" at a desired horizontal particle density plane to separate the desired clean coal product from the more dense refuse. The jig system includes means for continuously introducing the raw coal and for moving the water through the coal bed in a controllable manner, as well as for separating and removing the stratified particles from the system as two or more product streams. In coal preparation, this highly versatile unit operation is applied preferably to a wide size range of particles with top sizes up to 8 in. (20 cm) rather than to a closely sized fraction. In gravity ranges, the process has been applied to gold particles with a density of 19.3 and to coal particles having densities less than 1.30. Single jig washers have capacities from 5 (4.6) to greater than 700 tph (637 t/h) of feed coal. The separation results attainable by jigging have favored this unit operation as optimum for creating a clean coal product as required by steam coal specifications. Al- though the jig is used in preparing coals which are difficult to separate, its limitations to achieve both quality products and high recovery are being recognized in comparison with heavy media-based processes which make sharper separations from feeds having high "near-gravity" contents. The accu- racy of the densimetric stratification in the upper portions of the jig bed are less precise. It follows that coals with more than 10% near-gravity material

Jan 1, 1991

By Vittorio Manassero, Antonello de Risi, Filippo Cavuoto

"This paper deals with an innovative mechanized method to bore and simultaneously line circular shafts, adopted in the Naples Metro project for the installation of 10 vertical shafts for ventilation purposes. With this method, excavation of shafts is carried out under a positive head of stabilizing fluid by a milling machine, temporarily set at the bottom of a permanent lining made of precast reinforced concrete segment rings. The debris is evacuated by inverse fluid circulation. The shafts in Naples are 4.5 m I.D., from 34 to 44 m deep and they are all located downtown in a highly urbanized area. They were bored and installed into volcanic soils under a hydrostatic head of up to 30 m. Displacements and groundwater level were constantly monitored to keep control of the effects on the surrounding buildings and utilities. INTRODUCTIONThe extension of Metro Line 1 in Naples (Italy) from the previous terminal of Piazza Dante to Piazza Garibaldi is also called the “low stretch”. Most of it runs along the coastline, encompassing the historical city center, the Greek-Roman Neapolis. The Metro Line crosses under densely urbanized areas for the whole way (Figure 1). It runs beneath Via Toledo, which follows the layout of the ancient Aragonese walls. The first station (Toledo) is located halfway along this street. Then, after a wide bend, the line reaches Piazza Municipio, where the second station is located. From there, the line moves along the axis of Via Depretis and Corso Umberto I, where the stations Università and Duomo are situated. The fifth station is in Piazza Garibaldi and the end of the stretch is located at the Naples Business Center. The twin single track tunnels were bored into volcanic tuff by TBM. This design choice simplified by far the construction of the tunnels and reduced to practically zero the interactions between tunnelling and surface buildings and utilities. Nevertheless, this choice entailed that the line had to be located at depths to the order of 35-45m below ground level and 30-35m below the water table. At each tunnel segment between stations, a pair of ventilation chambers were constructed (10 in total). Each ventilation chamber is connected to one TBM tunnel by a vertical shaft and a horizontal drift at the base of the shaft. The shafts, in addition to tunnel ventilation, provide a safety access/escape."

Jan 1, 2016

By Jung-Hum Lee, Young-Joon Lee, Eui-Joon Hong, Seon-Hong Kim, Chan-Dong Kim, Keon-Woong Jeong, Ki-Lim Kim

"Subsea tunnel needs to be built over 50km long to connect between nations and continents. However there are only 19 tunnels longer than 5km in Korea, and there is no history of constructing and operating a tunnel longer than 50km. As the concept of a subsea tunnel, which withstands high water pressure and has an extremely long length is completely different from that of a land tunnel, all kinds of the latest technologies for tunnel construction are required such as survey and analysis of geology, design and construction under high water pressure, ventilation and prevention of disasters within an ultra long tunnel. Therefore, this paper describes the determination of tunnel cross-section under a high speed railway, structural stability, ventilation and fire safety under construction and operation, etc. through the virtual project for the length of 108km subsea tunnel under high water pressure of maximum 20bars from Honam to Jeju island in Korea. 1. INTRODUCTION The Honam-Jeju virtual project is subsea tunnel project to link from Honam(land) to Jeju(island) extending the currently operating Honam high speed railway line, and the same express train(t=18, design speed 350km/h, total train length 200m) operating at Honam line is applied in this project. As Honam-Jeju site is approximately 80km in straight distance with 160m maximum depth, subsea tunnel project should determine the various issues such as air quality/ventilation, aerodynamics, temperature, drainage, fire & life safety, structural stability. Figure 1. is the plan of subsea tunnel, with be constructed using Shield TBM. This double tube-Single track is composed of cross passages (every 350m in general section and 40m in emergency station), service tunnel, pressure relief ducts (every 250m), cross-over tunnels, shafts and emergency stations. 2. ALIGNMENT AND SITE CONDITON This project is planned as an ultra long tunnel of total length more than 105km via existing islands between Honam and Jeju island because straight alignment requires an artificial island which has high cost and construction risk, by deep water depth, though this is the shortest distance (see Fig 2). Water depth and topography in project site is divided into two blocks by Chuja Island. In first block to Chuja Island, depth of the water is 40m on average and maximum 60m, which indicates gradual change of water depth relatively. Also, outcrop bedrock is widely distributed near island."

Jan 1, 2016

By M. Li, J. K. Thompson, A. S. Azman

"Powerful mining systems typically generate high-level noise that can damage the hearing ability of miners. Engineering noise controls are the most desirable and effective control for overexposure to noise. However, the effects of these noise controls on the actual hearing status of workers are not easily measured. A tool that can provide guidance in assigning workers to jobs based on the noise levels to which they will be exposed is highly desirable. Therefore, the Office of Mine Safety and Health Research (OMSHR) of the National Institute for Occupational Safety and Health (NIOSH) developed a useful tool to estimate the hearing loss due to occupational noise exposure in a systematic way and evaluate the effectiveness of developed engineering controls. This computer program is based on the ISO 1999 standard and can be used to estimate the loss of hearing ability caused by occupational noise exposures. In this paper, the functionalities of this software are discussed and several case studies related to mining machinery are presented to demonstrate the functionalities of this software. INTRODUCTIONPeople regularly exposed to noise can develop hearing loss at different levels of severity depending on a number of factors. The resultant hearing loss can affect one’s ability to understand speech, learning, acoustic signal perception, or appreciation of music. Hearing loss caused by overexposure to noise has long been recognized in literature. However, it still does not get serious attention by those working in noisy environments because the loss of hearing ability is a gradual process and workers are often unaware until the damage becomes an apparent problem. In the United States, occupational hearing loss is one of the most common work-related illnesses. Depending on the definition of exposure and impairment, in 2012 the National Institute for Occupational Safety and Health (NIOSH) estimated that there are between 5 and 30 million workers in the U.S. who are exposed to noise levels at work that put them at risk of hearing loss.4 In the mining industry, noise-induced hearing loss (NIHL) is particularly severe due to the fact that heavy-duty machinery is widely used to improve production efficiency, and this machinery can generate much higher-level noise than the permissible level defined by regulation. As a result, the mining sector has the highest prevalence of hazardous workplace with high noise exposures (76%) among all industrial sectors."

Jan 1, 2015

By H. Wen, X. Zhai

"The Jurassic coal fields which lay in west China are the major energy base and contain half of coal resources in China. Due to the gather and degeneration rules, the spontaneous combustion characteristic of Jurassic coal is distinguished with permo-carboniferous coal, which needs to be studied deeply. Programmed heating experiments of five Jurassic coal samples and three permo-carboniferous coal samples from different primal coal fields in West China were conducted to identify the characteristic parameters in the low temperature stage of oxidation and spontaneous combustion. The experiments were carried out under non-isothermal heating conditions up to 180? at the heating rate of 0.33?/min in an air atmosphere. The result showed that oxygen consumption rate, CO gas production rate and heating intensity of all coal samples increased with the rising of the temperature, which of the Jurassic coal was higher than that of Permian-carboniferous coal. The C2H4 gas of Jurassic coal generated earlier, more than that of Permian-carboniferous coal in the process of oxidation and spontaneous combustion. It indicated that the Jurassic coal was easier to be oxidized and spontaneous combustion and the index parameters of spontaneous combustion were different between the Jurassic coal and permo-carboniferous coal.INTRODUCTION Coal was the foundation of industry development, and occupied 70% of primary energy production and consumption structure in China. According to the data of the 3rd coalfield prediction, 39.6% of the total coal resources were located in northwest Jurassic coal field in China [1], where the quality of coal was excellent. The study of northwest Jurassic coal already dated from the 80s of the 20th century, about coal rock composition, coal metamorphism [2], coal-derived hydrocarbons, coal structure [3], etc. The results of these studies showed that the composition and properties of Jurassic coal was obviously different from Permian-carboniferous coal, as well as the characteristic of spontaneous combustion [4]. As a result, the spontaneous combustion characteristic of Jurassic coal particularly needed to be studied. Now more and more methods could be conducted to test the characteristics of coal spontaneous combustion, for example, thermal analysis technology [5-7], programmed heating experiment [8-10] and coal spontaneous combustion experiment [11,12]. In these methods, programmed heating experiment could be conducted to determine the oxygen consumption rate, CO gas production rate and heating intensity quickly."

Jan 1, 2015

By L. Runqing, H. Yuehua, S. Lei, S. Wei

"Tin ore from the southeast of Yunnan in China is a complex polymetallic low-grade ore. Because of the highly disseminated extent ore, cassiterite flotation was applied in industrial production instead of the low efficient gravitational separation. Benzohydroxamic acid (BHA) was widely used as a collector in cassiterite flotation, but the consumption of BHA was large. In this study, the influence of octanol in cassiterite flotation from the southeast of Yunnan using BHA as the collector was investigated. The results indicated that single octanol showed almost no flotation capability to cassiterite without BHA. However a small amount addition of octanol as the auxiliary collector can decrease the consumption of BHA significantly, while did not reduced the recovery of cassiterite obviously. Infrared spectra analysis indicated that the single octanol adsorbed on the surface of cassiterite was unsteady adsorption, and a new entity assembled of BHA and octanol in a well manner was able to adsorb on the surface of cassiterite steadily. The probable self-assembly structure model of BHA and octanol existing on the surface of cassiterite was analyzed. INTRODUCTION Cassiterite is the prime and economic mineral from which tin metal is extracted economically (Qin et al., 2011). The estimated tin metal resources in the world is about 4.9 million tonnes, about 30.5% of which is distributed in China (Mineral commodity summaries, 2013). Cassiterite has many characteristics such as including heavy, hard, and extremely brittle in nature. Hence cassiterite is preferentially concentrated by gravity separators. However, the influence of particle size on gravity concentration is obviously. The separation efficiency is very high for coarse particles while it drops down considerably for fine sizes. (Turner and Hallewell, 1993). Application of flotation and development of selective surfactants have made it possible to recover fine and ultrafine cassiterite from the gravity tailings. A substantial amount of research work on cassiterite flotation has been reported in the past years. The outcome of such research has helped to develop various collector reagents such as cupferron (Vivian, 1927), sodium dodecyl sulfate (Edwards and Ewers, 1951), sodium oleate (Collins et al., 1968), salicyaldehyde (Marabini, 1978), alkyl and aryl arsonic acids (Senior and Poling, 1986), alkyl and aryl phosphonic acids (Gruner and Bilsing, 1992), alkyl sulfosuccinamates (Khangaonkar and Kamarudin, 1994), and alkyl hydroxamates (Sreenivas and Padmanabhan, 2002)."

Jan 1, 2016

By Gene E. McClelland, Dirk J. A. van Zyl

5.1 INTRODUCTION Heap leach cyanidation techniques possess considerable potential for exploitation of low-grade ores, small ore bodies, mine strip waste and tailing materials where fine grinding is not necessary for good extraction. For heap leaching to be successfu1, ore must exhibit certain characteristics, as previously discussed in Chapter 1. Primary among the necessary ore characteristics is that the ore must have good permeability after being crushed or treated and stacked into heaps if uniform distribution of the cyanide leach solution is to be achieved. Gold and silver ores containing excessive amounts of clays or fines generated by crushing are some of the most difficult to treat successfully by heap leaching. The presence of excessive amounts of slimes (generally classified as minus 50-micron or 270 Tyler mesh sieve size particles) in the heap leach feed will slow the percolation flow of the leach solution, cause channeling, or produce dormant or unleached areas within the heap. This may result in unreasonably long leaching periods and poor extractions. In extreme cases, the clays or slimes can completely seal the ore heap, causing the leach solution to run off the sides of the heap rather than to penetrate the ore heap. The problem of heap leaching ores containing fines can be aggravated during stacking and preparation of the ore heaps, because natural sorting of coarse and fine material occurs during these steps (Johanson, 1978). This phenomenon results in a concentration of ore fines at the center of individual ore piles and a concomitant concentration of larger rock fragments on the lower slopes and base of the piles. When the individual piles within the heap are leveled off prior to installation of the sprinkling system which delivers the leach solution, additional segregation occurs as the fines sift through the coarser ore particles. The segregation results in localized areas or zones with marked differences in permeability. As a consequence, the leach solutions follow the path of least resistance, percolating downward through the coarse ore regions and bypassing or barely wetting areas that contain large amounts of fines or slimes. Effective utilization of marginal gold and silver resources through heap leach processing requires the development of new methods in order to achieve more uniform size distribution during ore heap preparation and better slime control during leaching.

Jan 1, 1988

By Keh-Jian Shou

"This study adopts and analyzed a shield tunneling case in Taiwan, with a diameter from 5.25m to 6.70m and the smallest radius of curvature 100m, which was constructed in gravel formations as well as a vibration sensitive area. In this case study, a vibration monitoring plan, comprising the sensors inside the shield machine and on the surface, was proposed and performed to provide the vibration data during the construction. In this project, the major vibration reduction considerations were increasing the open ratio of the cutter head (to reduce the cutting function) and reducing the rotational speed of the cutter head. The results of the construction suggest the appropriateness of the above considerations. The findings could provide suggestions to the other similar shield tunneling cases. INTRODUCTION Underground vibrations during shield tunneling are typically isolated and absorbed by the soil. However, a portion of these vibrations may disseminate to the surface. These vibrations are considered micro-vibrations, which generally do not pose a threat to surface structures, and are thus seldom the focus of research. The present project was located in the Hsinchu Science Park where shield excavation bypassed numerous high technology manufacturing plants (e.g., wafer manufacturing plants). The vibrations generated by shield tunneling may affect the vibration-sensitive manufacturing equipment and instruments in these plants, and induce problems in manufacturing processes. Therefore, research to comprehensively understand the characteristics and potential influence of such vibrations is essential. To clarify the characteristics and potential influences of vibrations generated during shield tunneling, the vibration level in the excavation of the Taoyuan International Airport Access (TIAA) Metropolitan Rapid Transit (MRT) Project was examined, as it possesses similar excavation conditions to the present project. The parameters collected from relevant tests were provided as a reference to the firms along the excavation route of the present project to explain the effects of vibrations, and to relevant units for shield machine selection and project execution. No yield problems resulting from shield machine induced vibrations were reported by the firms, and the vibration levels measured in the present project were comparatively lower than those in the TIAA MRT Project. Because the related literature is scarce, this study aims to analyze the collected measurement data and provide suggestions on shield machine selection or designs. Such that we can more properly evaluate and control the impact of shield tunneling induced vibrations in similar projects."

Jan 1, 2016

By P. Henderson, M. E. Morris, W. A. Johnson, F. D’Alessandro, D. Wilton

"The objective of this research is to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models can then be utilised to assist in the design of effective controls. This project will provide a significantly improved level of knowledge and control over current lightning abatement techniques. The findings may also be applied to open cut and coal preparation situations. Computer modelling identified that by isolating cased boreholes from underground conductive media such as roof mesh, and placing spacings between roof mesh the risk of an ignition can be reduced by more than a factor of ten. These controls should be applied in conjunction with minimising the potential for a flammable atmosphere to exist underground and ensuring that there is no transmission medium for the lightning to reach the atmosphere. INTRODUCTION The objective of this research was to develop and apply computer models to evaluate the potential lightning impacts on underground coal-mining. These models could then be utilised to assist in the design of effective controls. If successful this project would provide a significantly improved level of knowledge and control over current lightning abatement techniques. The direct potential for harm from lightning has long been recognised for the surface facilities of coal mines. However recent events at Blakefield South in NSW on January 5 2011 (DTI, 2011) and at Sago mine in the USA in 2006 (MSHA, 2007) have suggested that there is potential for lightning to cause significant damage to the underground workings of a coal mine. A very detailed analysis carried out by as part of the MSHA investigation into the SAGO disaster by Sandia Laboratories identified at least ten other incidents over the past thirteen years where lightning had probably caused the ignition of a sealed goaf area of a mine (SANDIA, 2011). In addition there is a long history of lightning related incidents in South African coal mines (Geldenhuys, 1985). Fortunately in those cases no lives were lost. The event at Blakefield South has suggested that there may be the potential for ignition to occur in an active longwall goaf. The potential for a lightning strike to ignite a flammable atmosphere in an underground coal mine has been demonstrated from the past experience both here and overseas. It requires three things: • Lightning • A mechanism to convey the lightning underground to the flammable atmosphere • A flammable atmosphere."

Jan 1, 2016

By W. Robert Power

Stone is considered by many to be the premium material for beauty and durability in all kinds of construction. Its use dates to the dawn of civilization and only buildings made of stone have survived from ancient times. The use of stone relative to other materials declined from the beginning of the present century reaching a low point in the third quarter, but there has been a resurgence in the use of stone in construction during the past decade, due probably, to new techniques for producing stone, a greater recognition of its beauty and durability, and greater affluence among consumers. The aesthetic appeal of stone is attested to by the many attempts to simulate it in synthetic materials. Today, natural stone is considered by many to be the ultimate in aesthetic appeal, durability, and ease of maintenance. Consumption of dimension stone has increased dramatically during the past decade. The US Bureau of Mines reported that the total value of US consumption in 1978 was $1 13 million and that total imports were valued at $65 million in 1979 (Anon., 1980). In 1989 consumption of domestic dimension stone was valued at $208.3 million and imports at $525 million. This dramatic increase occurred after demand had decreased at an average rate of 2.5% in the two decades prior to 1978 (Anon., 1980). More than half of the imports come from Italy, but production of dimension stone has increased worldwide spectacularly. Meaningful statistics on dimension stone are hard to acquire. The finished piece of stone is a highly value-added product, but stone may be sold as rough blocks, sawed slabs, or finished product. The same piece of stone may therefore be sold and reported three or more times. Furthermore, although the quantity of stone is most commonly reported in tons, stone cladding is more often sold by the surface area and at the same price for different thicknesses. By any measure, however, the production and consumption of dimension stone has increased dramatically during the past decade. A significant indication of the resurgence of stone was the introduction of two new trade publications during the 1980s. Stone World (Tradelink Publishing Co., Inc., Oradell, NJ), introduced in 1984 is published monthly and Dimensional Stone (Dimensional Stone Institute, Inc., Woodland Hills, CA), introduced in 1985 is published monthly. Both magazines provide useful information on new technology, market trends, producing areas and companies, and other information not previously available.

Jan 1, 1994

By K. V. Raj, T. Bhowmick

"Computational fluid dynamics (CFD) modeling of an open-pit mine has several challenges. A good quality mesh of the model domain is a pre-requisite for convergence in solution. Good quality tetrahedral meshing and insertion of prism layers in faceted open-pit mine geometry is complicated due to presence of numerous vertices and ridges. Presence of vertices and ridges result in poor quality tetra elements and holes in prism layers, which cause instability in the model. Good quality pit bottom prism mesh elements significantly improve the formation of velocity boundary layer and thermal boundary layer at the pit bottom. This results in an expected temperature dependent micrometeorological buoyancy flow in the pit. Whereas, model geometry without a prism layer, results in abrupt temperature gradient near pit bottom. Buoyancy flow and recirculation have significant effect in lifting mechanism of fugitive dust particles generated near pit bottom. Representative initial and boundary conditions and selection of appropriate turbulence model have significant influences on the simulation results. In this paper, three-dimensional models of open-pit mines are developed using commercial CFD software (CRADLE-CFD). Important constraints and various consequences in modeling complex open-pit geometries are presented. INTRODUCTION Application of Computational fluid dynamics (CFD) to model an open-pit mine to predict fugitive dust and pollutant concentrations in and around a mine is relatively new. In former Soviet republic (USSR), Baklanov [1] and Belousov [2, 3] presented numerical models of pollutant transport in open-pit mines in Arctic regions. In recent years, advances in mathematical and computational fields have enabled better modeling of pollutant dispersion phenomenon around mines using computational fluid dynamics (CFD). Several CFD software packages have been used by various researchers to model the pollutant transport in open-pit mines. Works by Alvarez et al. [4]; Lowndes et al. [5]; Silvester et al. [6]; Torno et al. [7]; Choudhury and Bandopadhyay [8]; Collingwood et al. [9]; Raj et al. [10] and Flores et al. [11]; are examples of application of various commercial and open source CFD packages (COMSOL, ANSYS, OpenFOAM) to model pollutant transport in open-pit mines. These researches provided a strong background for additional research involving CFD modeling of open-pit mines. Due to the limitations of computational times and capacity, 3D modeling and various aspects of fugitive dust dispersion in open-pit mines remained unexplored."

Jan 1, 2015

By S. Hearn, S. Boskovic, A. Smethurst

"The digestion of minerals in strong acids or at elevated temperatures can result in the release of large amounts of silicic acid which can polymerize in solution to form colloidal silica and gels. Colloidal silica can cause a number of problems including interfering with flocculation, initiating crud formation in solvent extraction (SX), decreasing SX extraction kinetics and increasing SX phase disengagement times. Huntsman’s POLYSIL® polyether coagulants have a “lock and key” relationship with the surface of colloidal silica to help lower the concentration of these particles in solution, improve process efficiency and reduce reagent losses by minimizing crud formation. This paper investigates some of the issues caused by colloidal silica in hydrometallurgy processes and illustrates how the use of POLYSIL® coagulants has helped to improve process outcomes. INTRODUCTION Coagulation differs from flocculation in a number of ways. Coagulants are relatively small molecules that modify the surfaces of fine particles, weakening repulsive forces between them and allowing particles to stick together, while flocculants are generally molecules that are large enough to bridge the boundary layers between the particles. With flocculation, addition rate and mixing all make a difference to the flocs formed. Coagulation, on the other hand, is an equilibrium process. With coagulation it is only necessary to achieve good mixing, and coagulates will form as Brownian motion pushes the particles into each other. In real systems, this process is complete within seconds. Huntsman’s POLYSIL® polyether based coagulants have a strong affinity with the surface of colloidal silica formed by the polymerization of silicic acid. While silica found in minerals has a low aqueous solubility, large amounts of silica as silicic acid can be released as these minerals are digested in strong acids at elevated temperatures. The solubility of free silicic acid is about 150 ppm under pH conditions typical in acid leach environments (1), so the bulk of the silica will polymerize in solution to form colloidal silica. Colloidal silica can pass through a hydrometallurgy process without affecting any of the operations. However, it can cause a number of problems. These include gelling in a leach, interfering with flocculation or crystallization, initiating crud formation (2,3,4), decreasing extraction kinetics and increasing phase disengagement times (5,6) in solvent extraction. In these cases, coagulating the silica with POLYSIL® coagulants can reduce or eliminate the problem by enabling these particles to be flocculated and removed from the solution."

Jan 1, 2015

By Salam Moubarak, Thomas Camus

"INTRODUCTION Since the introduction, several decades ago, of the first concepts of tunnel boring machines (TBMs), the unremitting increase of mechanized and automated tasks and the reduction of manual tasks carried out by human operators have gone hand in hand with the continuous improvement of these machines. In the present state of TBMs, the replacement of worn cutting tools is a critical, tedious, and dangerous manual operation especially for earth pressure balanced (EPB) and slurry TBMs. For such pressurized TBMs, hyperbaric interventions are used. They consist in replacing the pressurized soil/mud inside the chamber with compressed air that balances the face pressure. The operators can then ""dive"" into the chamber; however, because the human body cannot naturally undergo pressure changes, they have to follow strict procedures that have been developed for subsea divers, based on decompression stops. Indeed such interventions are actually quite often performed by professional deep-sea divers. The pressurized TBMS are consequently equipped with a manlock that allows for the required compression and decompression cycles. Hyperbaric interventions increase risk to the operators and require long decompression procedures that increase the TBM idle time and reduce its efficiency. At higher pressures, over 3.5 bar (ITA Report No 10, 2011), specific equipment and special gas mixes and/or saturation techniques are recommended (Lamont, 2012). Such procedures are even more expensive and time consuming although the duration of work in the pressurized area can be very limited for health and safety reasons. Contractors are therefore increasingly interested in automating these operations to reduce the risks to human workers and improve the TBMs performance. Moreover, the demand for new, ambitious and challenging tunneling projects (very deep, high pressure boring) is ever increasing, but the supply of suitable TBMs is limited and the risk from working in the hyperbaric environments becomes increasingly unacceptable. Impact of hyperbaric interventions The UK Health & Safety Executive has analyzed the consequences of working in intermediate pressure compressed air. The retrospective study of decompression illness (DCI) indicated that at certain pressures its incidence was around 2% of all exposures. More worryingly it showed that over 20% of the exposures commonly undertaken by shift workers in tunneling (those over 1 bar pressure for 4 hours or more) resulted in DCI. It was concluded that on some contracts up to 50% of shift production workers experienced DCI at some time during the contract, a situation which was considered to be wholly unacceptable (Lamont, 2006)."

Jan 1, 2016

By Cary Hirner, Dan Lopez, Ross Webb, Stephen O’Connell

"Construction of the largest desalinization plant in the Americas has commenced in northern Chile. It is part of a several billion dollar expansion at a copper mine whose operations nearly stopped due to the challenge of securing a reliable source of water from the Pacific Ocean in a safe and environmentally sound manner. This paper discusses the risk management, design and construction of a quadruple chamber intake and outfall shaft, high capacity pump station, three 7m diameter vertically drilled marine shafts and three subsea tunnels constructed through challenging Andean hard-rock geology. The three 2.5m diameter subsea microtunnels are being mined with vertical curves through variable quality rock 30 meters beneath the ocean and retrieved in the wet from the 7m diameter marine shafts. INTRODUCTION AND BACKGROUND The battle for securing the rights to a constant water supply is a worldwide issue and nowhere is that more evident than the Atacama Desert of Chile, the world’s driest place with areas of the desert that have not seen rainfall in recorded history. The Atacama Desert also happens to be home to some of the world’s largest ore deposits which require huge amounts of water to extract and process. What available water there is comes from three main sources: deep seated wells, glacial water from the Andes Mountains, and desalinated water. Vying for water from wells and glacial streams and lakes are numerous agricultural and domestic facilities in the valleys surrounding the Atacama Desert. Environmental regulations and legal rulings have limited the amount of “natural” source water which can be used for mining purposes. Desalination plants are a known solution for combating water scarcity, albeit a costly one. The total estimated cost of constructing this desalination plant is over $3B USD, which will include a 2500lps capacity and an approximately 118km pipeline from the coast up to the mine located in the Andes. The overall scope of the project includes design, procurement, and construction packages for the 2500lps desalination plant including the seawater reverse osmosis plant, water conveyance to the mine, power transmission, the reservoir and the marine works package which forms the basis of this paper. Key components of the underground construction portion of the Marine Works are:"

Jan 1, 2016

By P. M. Jones

Introduction The success of in situ leaching depends upon: • maintaining adequate injection and recovery flow capacities in wells, and • distributing leach solution effectively to contact and leach ore minerals within the target zone. Solution balance is an important indicator of the capability of a particular in situ hydrologic design to efficiently and effectively control and distribute leach solution within the target ore zone. As part of ongoing hydrological investigations into in situ leaching, the US Bureau of Mines (USBM) is studying factors affecting solution balance in an unsaturated copper ore deposit at the Cyprus Casa Grande Mine. The purpose of this study is to assess the effect of hydrogeologic features and in situ operating conditions on changes, during leaching, in: • solution storage within the deposit, and • solution balance. At the Casa Grande Mine, In-Situ-Leaching Test Facility, solution balance estimates are obtained for 10 selected intervals during 17 months of leaching under a variety of well configurations, pressures and flow conditions. Operational and geological description The Casa Grande Mine is located 32 miles south of Casa Grande, AZ. The mining area is within the Casa Grande Deposit, a porphyry copper stock consisting primarily of an intensely-fractured, granodiorite cap overlying a copper sulfide base. As a result of mine dewatering activity, unsaturated conditions existed in the deposit prior to leaching (Schmidt et al., 1990; Friedel and Schmidt, 1991). No groundwater was present in any of the in-situ-leaching, test-facility wells after drilling and prior to leach solution injection. Also, no ground water seepage occurs in the test-facility drift. The Casa Grande, In-Situ-Leaching Test Facility consists of 58 injection and recovery wells collared in an underground drift. The wells were drilled at various angles into the granodiorite deposit in a series of 15 divergent fans (Fig. 1). The fans are 12.5 ft apart and lie parallel to one another between the 900- and 1100-level drifts. Each fan contains three to five wells drilled at angles ranging from 6° to 89° from the horizontal. The wells can operate in an injection or a recovery mode. Currently, 36 flow sensors and 28 pressure transducers (part of a hydrologic, data acquisition system) are used to continuously monitor injection-well flow rates and pressures.

Jan 1, 1993

By Frank A. Aplan, Barbara J. Arnold

INTRODUCTION Coal flotation is a fine cleaning process usually present in all but the older preparation plants. It is typically used to clean either the -28 mesh (-500 pm) or - 100 mesh (- 150 pm) raw coal fines, and it is the only commonly used preparation method that can effectively recover coal particles finer than, say, -200 mesh (74 pm). To place coal flotation into its proper context, it should be noted that the bulk of the raw coal sent to preparation plants is treated by gravity concentration. On a worldwide basis, from 0 to 40% of the raw feed to a preparation plant is treated by flotation, while in the US only about 10% of the raw coal feed is floated. Roughly, 50% of US preparation plants use flotation to process at least a portion of the raw coal feed, although most of the newer plants incorporate flotation into their flowsheet. Historically, the process has only been used to treat the raw coal fines naturally occurring after mining and a minimal amount of crushing at the preparation plant. This is in sharp contrast to ore flotation where, typically, the entire tonnage is first ground and then floated. As a consequence, of the approximately 500 Mt of raw coal treated by preparation in the US yearly, it is estimated that only about 40 Mt are sent to the flotation circuits (producing -30 Mt of clean product).'O1 This small tonnage compares with about 400 Mt of ores treated annually in the US by flotation. By analogy to ore flotation, where it is an effective, large tonnage, low cost, easy to operate process, its potential in coal preparation should be great. Reasons why it has not achieved a greater potential in coal preparation have been attributed by Aplan 102 to: 1. Indifferent results in removing sulfur and ash. 2. Difficulty in floating low rank and oxidized coals. 3. Inability to make clean separations with the finer sizes. 4.Inability to clean slurries with a high percentage of clay. 5. Problems with water chemistry. 6. Competition with effective, gravity coarse-cleaning methods. 7. Low value of coal historically. 8. Dewatering problems. 9. Transportation and storage problems with coal fines. 10. Marketing problems with coal fines. 11. Inadequate attention to the process in the plant. 12. Inefficient use of capital and operating monies. Inadequate attention to procedures, machines, and processes.

Jan 1, 1991

By S. K. Kawatra, S. K. Valluri, S. J. Root

Carbon dioxide, a by-product of combustion reactions, is a greenhouse gas linked to climate change. At Michigan Technological University, we have studied the capture of CO2 using alkali scrubbing solutions in a pilot scale packed bed counter-current scrubbing column. To do this, we have simulated flue gas by combining streams of CO2 and compressed air. Real flue gas has impurities such as CO, SO2, and NOx, and has lower levels of O2 than our simulated flue gas. In order to study CO2 capture from a real flue gas, the Department of Chemical Engineering worked with the Facilities department to install a pilot scale scrubbing column in the Michigan Tech steam plant. Experiments were conducted using a sample stream of the flue gas from the boiler in the steam plant. Data collected from these experiments were compared to the data collected from identical experiments conducted on simulated flue gas in the lab. The capture efficiency of the real flue gas scrubbing column is discussed in this paper. BACKGROUND The most common equipment used to separate CO2 from a flue gas stream is a counter-current packed-bed scrubbing column. The department of Chemical Engineering at Michigan Technological University has two such pilot scale columns. In order to study the effect of impurities found in real flue gas, one is installed in a controlled laboratory using a simulated flue gas created by mixing CO2 and compressed air. This column will be used to establish a baseline for percent capture analysis and is displayed by figure 1. The second scrubbing column is identical to the first, and is installed in the Michigan Tech central energy plant. The plant produces up to 130,000 lb/hr of 80 psig steam to provide hot water and heat for campus buildings. A typical wintertime load burns around 25,000 SCFH of natural gas; this load releases 1.4 metric tons of CO2 per hour. The flue gas the steam plant produces is roughly 7.5% CO2 by volume. In order to study CO2 capture from this flue gas, a tap has been installed on the main exhaust duct which draws a sample of the flue gas into the pilot scale scrubbing column. Figure 2, a simplified diagram of the steam plant, shows that the tap was installed between the economizer and the stack condenser.

Jan 1, 2019

By Thomas O. Glover

History of Underground Coal Mining in Illinois The production of coal in Illinois using underground mining methods, commenced early in the 1800's; however, the first shaft entrance was not sunk until 1842. The shafts range in depth from 16 feet (4.9 m) in Peoria County to 1,001 feet (306 m) in Christian County. The earlier mines were smell, private operations that worked outcrops and shallow seams at less than 100 feet (30.5 m) in depth. By 1975, there were reported 4,076 abandoned underground coal mines in 70 Illinois counties (Nawrot, 1977). There were many more mines; however, only 4,076 underground mines have been documented. Small mining operations characterize the majority of the underground mines. There have been no significant multiple seam operations in Illinois. The most extensively mined seams were the number two, five, and six seams. Number two seam was worked in the early 1900's by 252 mines in the longwall mining region of northern Illinois (Nawrot, 1977). Available records for 2,054 abandoned mines identify 1,043 as shaft nines, 700 as slope mines, and 311 as drift mines. Some operators began reporting annually to the State Department of Labor in 1879 and by 1882 all mine operators were reporting. Annual reporting still continues to date. The information is compiled by the State Department of Panes and Minerals in their "Annual Coal Report." By the end of 1974 there were 800,000 acres (323,756 hectares) of abandoned underground coal mine workings (Smith-Stall, 1975)2 Copies of abandoned underground coal mine maps may be inspected by interested parties in the State Department of fines and Minerals office in Springfield, Illinois, or at the office of any county recorder for mines within their county. Copies of active underground coal mine maps may be inspected at a State mine rescue station near the mine site or at the county recorder's in the county in which the mine is located. Copies of active underground coal nine naps shall be open to the examination of all interested persons, but such examination shall be made only in the presence of the State mane inspector or the recorder. At the present time, the Department of Mines and Minerals has 1,746 maps of abandoned underground coal mines in its possession. These maps cover the majority of

Jan 1, 1977

The Mining Foundation of the Southwest (MFSW), located in Tucson, AZ, will hold its 16th annual American Mining Hall of Fame Awards Banquet Saturday, Dec. 5,1998. The Hall of Fame recognizes outstanding contributions to the mining industry by selected individuals and industry partners. Each year, one living award recipient and up to two mining history honorees are chosen by the , Hall of Fame Committee and the Board of Governors of the Mining Foundation. In 1989, the Mining Foundation initiated a Medal of Merit to recognize outstanding individual, technical and professional contributions to the mineral industry. In 1995, an award was created to recognize contributions made by companies and organizations in partnership with the mining industry. This year's inductee, guest of honor and featured speaker will be Charles G. Preble, president and chief executive officer of Southern Peru Copper Corp. He is being recognized for outstanding performance as an executive of an American company operating under difficult circumstances in a foreign country. The Hall of Fame will induct H. Myles Jacob, former chairman and CEO of Inspiration Copper Co., for innovation and farsightedness in matters pivotal to the cop- per industry of his time. In addition, John Cromwell Lincoln, former president and chairman of Bagdad Mining Co., will be inducted for his outstanding contributions to the American mining industry. These contributions include metallurgical research and development of the Bagdad Mine as well as pioneering innovation in the electrical industry. Medals of Merit will be awarded to David N. Skillings, editor and publisher of Skillings Mining Re- view, for his dedication and support of mining interests. J. Ruben Velasco Rodriguez will also receive a Medal of Merit. He is economic geologist, professor and former secretary of the board of directors and secretary general of Compania Minera de Cananea. His medal is for fostering excellent relations between Mexico and the , United States in mining geology and management and for advancing the professional development of others in the field of earth science. An Industry Partnership Award will be presented to Stephen Bechtel and the Bechtel Corp. in recognition of Bechtel's 100th anniversary and the company's outstanding service to the mining industry. The banquet will be held at the The Westin LaPaloma in Tucson beginning with cocktails at 6:30 p.m. Tickets are available from Clare A. Roscoe, manager, Mining Foundation of the Southwest 520-577-7519, fax 520-577-7073.

Jan 1, 1998

By Ezra L. Kotzin

Foundry sands used to make molds and cores have been very important to foundrymen since metal casting began hundreds of years ago. They are now used in two basic ways, either in an uncured green state, grain-bonded with clay, or in a set cured state achieved with sand that, mixed with resins or oils, is cured by baking or by chemical reaction. The term sand, as generally used in foundry applications, may best be defined as material composed of granular particles of mineral matter, ranging in size from 0.5 to 2 mm in diameter. The particulate nature of the material may be the result of natural disaggregation or result from crushing and screening of rock or ceramic materials; crushed and screened products are sometimes referred to as "manufactured sand." Based on their origin, the raw materials for foundry sands will vary in grain shape, grain composition, relative surface, grain size, and grain distribution patterns. These properties, in addition to their chemical analyses, sintering point and expansion characteristics play an important part in the choice of sands used as the base molding or core aggregate in metal casting. Sands with different origins may be blended to produce specific compositions and grain size distributions. Early raw material requirements based on silica sand were simple, but as sand/core/mold technology became more sophisticated and binder technology continued to be developed, the physical properties of foundry sands became more critical. Silica sand is composed of quartz, along with, in most cases, small amounts of feldspar, mica, clay, and other common minerals. Although silica sand is still by far the most widely used base material in production of molds and cores used in metal casting, other natural mineral sands have their own unique characteristics and fill an important niche in special applications. As a result, the term sand, as applied to raw materials used in metal casting, has been logically extended to include granular materials composed of a group of minerals other than quartz. With increased use in advanced foundry technology, natural sands composed predominantly of zircon, chromite, staurolite, or aluminum silicate minerals and of granularized chromite or olivine, have become more than just alternate materials and are now commonly classified as sands when the grains are sand-sized. Foundry sand may therefore be considered under two categories: silica sands and non-silica sands.

Jan 1, 1994