Search Documents

By K. A. Natarajan, J. M. Modak, B. Saha

Nonliving waste biomass consisting of Aspergillus niger attached to wheat bran was used as a biosorbent for the removal of copper and zinc from aqueous solutions. Copper and zinc uptake by the biomass obeyed Langmuir isotherms. The binding capacity of the biomass for copper was found to be higher than that for zinc. The metal uptake, expressed in milligrams per grain of biomass, was found to be a function of: •the initial metal concentration (with the uptake decreasing with increasing initial concentration), •the biomass loading (with the uptake decreasing with increasing biomass loading) and •pH (with the uptake increasing with increasing pH in the range of L5 and 6.0). The metal uptake was significantly affected in the presence of a co-ion. The uptake of copper by the biomass decreased in the presence of zinc and vice versa. The decrease in metal uptake was dependent on the concentrations of metals in the two-component aqueous solutions. The effect of copper on zinc uptake was more pronounced than the effect of zinc on copper uptake.

Jan 1, 1997

By Kerby Glass, Glenn A. Gruber

Mr. C. A. Hollingsworth introduced commercial column flotation to the Florida Phosphate Industry in 1976, with a six feet diameter prototype cell at the Tenoroc Mine. More than two-dozen column cells have been installed in phosphate beneficiation plants since then. The increased interest in column cells for phosphate flotation, and their potential use in new plant construction, prompted the Florida Institute of Phosphate Research to fund programs to investigate various aspects of column flotation. This report describes a test program, conducted by JACOBS at CF Industries Hardee Complex II, as part of a comprehensive research program awarded to the University of Florida by the Florida Institute of Phosphate Research. The 1.5 feet diameter test column was operated with plant process water and plant reagentized flotation feed. Several variables considered for column cells design and operation were tested. Feed specific capacity, air superficial velocity, and the length to diameter ratio of the column were the variables that influenced phosphate recovery. Concentrate phosphate grade was influenced by concentrate superficial velocity and feed specific capacity.

Jan 1, 2002

By M. G. Karfakis

This paper examines the chimney occurrences in the Hanna Coal Field, Wyoming. Chimney caving is defined, previously proposed mechanisms involved in the development of a chimney are critically reviewed, and factors controlling chimney cave are identified. The main portion of this paper deals with the identification and characterization of chimney subsidence due to underground coal mining in the Hanna Mining District. In an attempt to characterize the subsidence, sink-hole occurrences are correlated with the depth of coal, thickness of mined-out beds, mining methods, nature of overburden, structural geology, and hydrology. Most sinkholes in the Hanna Basin appear to be conical in profile, with the apex upward. The average diameter is 15 meters (50 feet), with an average depth of 11 feet. Most have developed above an overburden of less than 61 meters (200 feet). The average mining height to width ratio is 5. Much of the chimney development is governed by the thickness and character of the overburden, the width and height of the mine opening, and the in situ state of stress.

Jan 1, 1986

By Sterling S. Cook

The U.S. Bureau of Mines is conducting core leaching experiments with sulfuric acid on oxide copper ores from the Cyprus Casa Grande and ASARCO Santa Cruz deposits in Arizona to further our understanding of the leaching process in supergene copper ores as it relates to in situ mining. Leach solutions from atacamite mineralization contained 5 to 30 g/l copper and few extraneous ions. Leachant from chrysocolla ores, with grades similar to the atacamite, contained 2 to 9 g/l copper and abundant extraneous ions. Quartz and K-feldspar had no impact on leach solution composition at any acid concentration (up to 40 g/l) while illite and sericite had minimal impact. Biotite, calcium-rich clay and limonite have a significant impact on solution chemistry when there is abundant free acid in solution. High acid concentrations increase acid consumption in ores with abundant biotite and limonite gangue. High acid concentrations can be used in ores with quartz, K-feldspar, and sericite gangues without increasing acid consumption per unit of copper removed.

Jan 1, 1988

By G. Almgren

With the exception of sublevel caving, the most common method of underground mining in Sweden is the "cut-and-fill" method. It is normally used for mining non-ferrous metals , and' is used extensively in the complex sulfide ore mines of the Boliden Company in north and central Sweden as well as the mines of the STORA and Vieille Montagne Companies in central Sweden. All in all, the cut-and-fill method is used in 13 of Sweden's 45 mines. As the mines are relatively small, the volume of ore mined by this method represents only about 5 % of the total ore production in Sweden. The commercial value, however, is much large than this percentage would imply. The production volumes and grades of some typical mines are shown in Table I. As seen, when rated internationally, the grades are comparatively low. The prices are set according to ?international metal prices? as dictated by the London stock exchange, and in lieu of governmental support, rational management methods are critical in order to achieve satisfactory profit.

Jan 1, 1975

By R. J. Matetic

The Bureau of Mines, as part of a program to improve mine planning and development, is currently investigating the effects of pillar load transfer, which can impact mining operations within a multiple-seam configuration. A comparative study was performed at two separate mine sites to determine the effects of this load transfer mechanism. The Bureau installed and monitored instrumentation at both sites to gather pertinent data on rock mechanics. At mine site A overburden depth varied dramatically in the vicinity of the study area and reached a topographic high at the study site: inner burden thickness was less than a pillar width (40 to 45 ft) (12 to 14 m): floor heaving was experienced in both coalbeds where sandstone and/or shale floor units were observed: overlays of the mine layouts show pillars were not totally super-positioned: a maximum of 5 in (13 cm) of roof to floor convergence was measured and pressure readings indicated pillar core loading only and increased to a maximum of 7,000 psig (48,300 kPa) over instrument setting pressure.

Jan 1, 1989

By James A. Martin

Evaluation and subsequent development of a quarry in east-central Missouri was based on a general but brief examination of outcrops and core from five (5) test holes. Neither core, outcrops, nor existing quarries in the general area gave any indication of potential major problems. In the third year of operation large areas of collapse rubble, consisting of green shale and large blocks of limestone and sandstone, were encountered. Their size and random distribution resulted in both blasting and quality control problems. By the fourth year of operation, production costs became prohibitive and the site was abandoned. Prior to dismantling the plant a geologic investigation, which included shallow seismic and resistivity surveys, was made of the unmined portion of the lease. The collapse dolines appear to be related to structure and predate development of the modern topography. Surface indications of these features are few. The seismic profiles were especially helpful in plotting their distribution. Geologic relationships and seismic data developed at this site are being related to similar suspect areas in Missouri and have been useful in their evaluation.

Jan 1, 1970

By G. J. Lindenburg

The Velvet mine is located in the Big Indian district of the Colorado Plateau. The general area, also known as the Lisbon Valley district, is about 65 kilometers southeast of Moab, Utah and about 120 Kilometers southwest of Grand Junction, Colorado. As shown by the slide, the Velvet area is typical of the high desert of the southwest United States. The elevation at the decline collar is 1,967 meters above sea level. To date, the Velvet has produced 1.5 million kilograms of U308 and 2.1 million kilograms of V205. The current production averages over 4,000 metric tons of ore per month. Access to the Velvet mine is by a 1,160 meter long decline. Fresh air is supplied through the decline and a 152 centimeter cased borehole. Contaminated air is removed by two 152 centimeter cased boreholes. The east side of the mine is mined using a conventional room and pillar method; whereas the west side is mined as combination conventional and random room and pillar,

Jan 1, 1983

By R. Kingman

At Tahawus, New York, National Lead Company operates the MacIntyre Development, This operation produces 10,600 long tons of ore per day for crushing, 8,000 tons for grinding and processing, of which 2,000 tons per day reports as tailing for disposal in an impounded tailing storage area. With the change in location of mining operations at the mine of National Lead Company, a change in the area for tailing disposal by gravity became necessary, This called for the diversion of tailing from near the proposed mining area to areas more favorable for long term storage by gravity. In order to avail the operation of maximum storage for the future, a uniform minimum grade launder was proposed with a minimum velocity and maximum outfall at the discharge. Disposal of the gravity and flotation tailing was formerly accomplished in open ditch from the concentrator at a grade of 1.5 percent. It was desirable to design the new launder at grades less than this for the greater storage elevation.

Jan 1, 1966

By S. K. Kawatra, S. J. Ripke

During iron ore pellet production, bentonite clay is used as a binder. Typical pellet plants spend from $3 million to $5 million annually for the clay. If bentonite dosages could be reduced by using it more efficiently, a significant cost savings would result. If the binding mechanisms can be completely understood, procedures can be developed to use bentonite more efficiently. Classical bentonite bonding theory is based on the behavior of bentonite at low percent solids and high mixing shear rates. Under these conditions, bentonite was understood to expand, disperse into platelets, and dry into a bonding "film" or "gel." However, these are not the conditions that exist during pelletization, which is carried out at high percent solids and relatively low shear rates. In this paper SEM imaging was used to identify and explain the bonding mechanisms of bentonite on the surface of magnetite concentrate. It was determined that bentonite would form a fibrous network under the proper conditions and that the formation of these fibers corresponded with an increase in the bonding of particles by the bentonite.

Jan 1, 2000

By M. Takayasu, J. Y. Hwang, F. J. Friedlaender, G. Kullerud

Al unite has been used as raw material for producing alumina and potassium sulfate fertilizer in Russia for many years. In the United States, this mineral has not been commercially processed though reserves of 5 to 10 billion tons of alunite ore have been estimated. Major constituents of these ores are quartz and alunite. The minerals are finely intergrown and liberation occurs below 10 µm. Adequate separation techniques for such ultrafine particles have not been developed. A new method for the beneficiation of al unite ore is proposed in this study. This method utilizes a small amount of fine magnetite upon which the liberated quartz is selectively flocculated. The co-flocculated magnetite and quartz are then separated from the alunite in a high gradient magnetic separator. Clean products, e.g., an al unite concentrate of 90% grade with 80% recovery, has been obtained from Utah ore. Techniques for selective co-flocculation of magnetite and quartz, separation of the carried quartz, and recovery of magnetite after separation are discussed.

Jan 1, 1987

By Merrill P. Allen

The Vernal phosphate rock concentrator is located in the Uinta Mountains near Vernal, Utah. Ore is sedimentary rock from the Phosphoria Formation. Truck and shovel mining is done at a rate of 11,500 TPD. Run of mine ore is crushed and then milled through a SAG mill and ball mill to minus 16 mesh. Milled ore is deslimed using cyclones and hydrosizers. Sands are conditioned with fatty acid, petroleum sulfonate, diesel fuel and frother prior to primary rougher and cleaner flotation. Primary flotation tailing is milled to 95% minus 48 mesh, deslimed in cyclones, conditioned using reagents previously described, and then processed through rougher and cleaner scavenger flotation. Product of scavenger cleaner concentrate is upgraded by reverse flotation of dolomite. Flotation concentrates are combined and dewatered, pulp being milled to 99.5% minus 65 mesh and then thickened to 65% solids. Product is pumped from storage through a 10 inch, 94 mile pipeline to a conversion plant at Rock Springs, Wyoming. Mill tailing is stored behind an earthen dam, water from the settled tailing being reclaimed for mill use.

Jan 1, 1993

By B. J. Arnold, F. F. Aplan

Prior laboratory work has demonstrated that much of the fine ash forming minerals entering a flotation froth are there as a result of water carryover- from the bulk contents of the flotation cell (Arnold and Aplan, 1986a). Using a bank of four 8.5 m3 (300 cu ft) Wemco flotation cells cleaning a well-liberated Lower Kittanning seam coal, test results show that the sulfur and ash content of the froth is directly related to the water content of the froth (or inversely related to the percent solids in the froth). Reagent changes that result in a watery froth produce a higher ash content in the froth. A direct comparison of laboratory and plant results show that the standard laboratory flotation test produces a product higher in sulfur and ash than that produced in the plant. Caution should be exercised when extrapolating laboratory test results to the plant situation. A method of estimating coal flotation product quality in the plant based on laboratory tests is given.

Jan 1, 1991

By M. R. Yalamanchili, W. H. Jang, Y. Ye, J. D. Miller

Typically, rougher molybdenite flotation and recovery from bulk copper/molybdenum concentrates involves the use of alkalisulfides, Nokes reagents, cyanides, oxidants, and/or thermal treatment to depress copper sulfide minerals. The bulk copper/molybdenum feed generally varies from 0.2% Mo to 1.0% Mo, and with traditional reagents the single-stage rougher flotation recovery of molybdenite varies between 40% and 90% at a concentrate grade of 5% to 10% Mo. With ozone conditioning for copper depression, however, improved separations appear to be possible, as demonstrated by tests with Cu/Mo concentrates from both the Phelps Dodge Morenci Operations and the Kennecott Copperton Operations. Single-stage rougher flotation after ozone conditioning can provide a molybdenum concentrate at a recovery of more than 90% and a rougher concentrate grade higher than 20% Mo in some cases. Subsequent cleaner flotation with additional ozone conditioning resuIts in relatively copper-free molybdenum concentrates containing as much as 52% Mo. Preliminary analysis indicates that, with a multistage ozone conditioning/fotation strategy, the process is technically and economically viable and should be suitable for industrial ap¬plication.

Jan 1, 1991

By H. Soto, J. Jara, F. Nava, J. B. Hiskey, B. J. Scheiner

Laboratory tests showed that ozone can destroy free cyanide and weakly complexed cyanide (copper and zinc cyanides). The iron cyanide complexes were resilient to ozonation but they were effectively eliminated by precipitation with Fe (II) ions under controlled pH conditions. Tests carried out with effluents from a number of gold mills confirmed the results obtained previously in the laboratory. The industrial samples contained cyanide in the form of free cyanide and also complex copper, zinc and iron cyanides. Solutions that contained up to 184 mg/L total cyanide, after the ozone treatment analyzed only 2-3 mg/L dissociable cyanide and 50-90 mg/L CN(t) (accounted for by iron complexes). After precipitation with ferrous ions total cyanide was reduced below 1.5 mg/L. For most solutions ozone consumption ranges from 3 to 6 g per g of cyanide destroyed. However, certain impurities (such as SCN and S203 ), present in some effluents, increase ozone consumption and make it more difficult to reduce copper concentration to satisfactory levels.

Jan 1, 1993

By P. C. Cochrane, I. S. Clelland, S. H. E. Phillips

Geological and hydrological conditions in the strata overlying the Salado Formation vary considerably in the Carlsbad, NM, area. The first four shafts sunk at International Minerals and Chemical Corp. (IMC) property have been located in competent and essentially dry conditions, while other shafts on adjacent properties have had such adverse conditions that ground freezing has been chosen as the water and ground control technique for shaft sinking. At the location of the IMC No. 5 shaft there has been extensive erosion and salt dissolution in the Rustler Formation, leading to collapse of some zones of the strata. Both ground freezing and pregrouting were considered as alternative methods of stabilizing the extremely poor ground conditions and controlling the potentially very heavy water inflows. It was decided that pregrouting the shaft was feasible and would offer substantial cost and time saving over a ground freezing technique. This paper describes the pregrouting techniques used and illustrates the requirement for flexibility in a grouting program so that it can be modified to reflect any new or additional information obtained during the progress of the grouting.

Jan 1, 1987

By B. Moudgil, Hassen El-Shall

Particle shape and size distributions are among the most important parameters that affect the filtration efficiency of phosphogypsum in wet- process phosphoric acid production. Cost-effective enhancement in filtration rate is desired by phosphoric acid producers for higher plant capacity and lower operating costs. In this regard, numerous research efforts have been carried out in different laboratories as well as in pilot and plant testing. Nevertheless, changes in phosphogypsum crystal shape and size distribution deserve special attention. In this study, the results obtained in the presence of Crysmod and Hiflo-S5 surfactants are discussed. The influence of such additives on crystal morphology and size distribution are studied under different sulfate contents (supersaturation). The obtained data are correlated with process efficiency parameters such as filtration rate, digestion of rock, and recovery of phosphate values. Up to 60% increase in filtration rate is obtained. In addition, an increase in digestion efficiency and P205 recovery is achieved due to addition of surface active agents. The observed beneficial effects are explained in the light of the changes induced in crystal habit, size, and size distribution.

Jan 1, 1999

By John M. Hird

Texasgu1f's Lee Creek Mine in Eastern North Carolina is usin8 a combination Dredge-Dragline method for mining deep phosphate ore at a rate of 8.5 million tons per year. The matrix is thick, uniform in grade, and is processed into agricultural products. As in many other good mineral deposits, there are tough obstacles to overcome in recovering the ore. The deposit is in an area with a land surface of about ten feet above sea level, is close to tidewater, is overlain with 90 to 130 feet of unconsolidated overburden, and is underlain by an artesian aquifer with over 140 feet of natural hydrostatic head at the bottom of the bed, The upper 40 feet of overburden will not support stripping equipment and is unstable when cast as spoil. Barriers are emplaced to prevent flooding from hurricane tides. The ground water problems have been successfully controlled by pumping 60 million gallons per day from the aquifer. Only recently have the severe ground problems been overcome by this unusual Dredge-Dragline combination of mining equipment.

Jan 1, 1978

By Frederik P. Agterberg

Mineral exploration consists of the acquisition of data and their interpretation to ascertain the presence or absence of uncertain events. In general, the amount of uncertainty decreases during exploration when targets become increasingly well defined. Decisions on further exploration and whether or not mining should be commenced are based on new information using both objective facts and subjective reasoning. Computers play an important role during all stages of exploration. Three recent books (References 1-3) on decision-making in exploration and mineral-resources evaluation provide additional background supplementing the papers in this volume and articles in scientific journals or other conference proceedings (e.g., References 4 and 5) dealing with the subject. Other new developments to be considered are that microcomputers are becoming increasingly important in the earth sciences (Reference 6), and so are applications of artificial intelligence (Reference 7). Microcomputer- based technology allows rapid communication between field parties and main office. Expert systems are becoming increasingly sophisticated aids for mineral exploration an can now contain objective rules based on statistical theory (Reference 8).

Jan 1, 1989

By C. Menidiatis

The first cement plant of TITAN Cement Co was founded in Elefsis in 1902. It was the first cement industrial facility to operate in the Balkans and in the Eastern Mediterranean region. Currently have four cement plants in Greece producing 5.4 million tons per annum, and 25 ready-mixed concrete sites producing 1.4 million m3 annually. It has a total of 20 quarries, 14 of which are producing materials used in the making of cement while the remaining six produce aggregates used in the production of ready-mixed concrete. All plants in Greece are accredited for ISO 14001. The restoration of quarries began in 1976 at the company?s limestone quarry of the Patras plant, and was soon extended to all quarries. At that time, a department responsible for all environmental issues was established. To date, over 700.000 shrubs and trees have been planted and maintained at quarries, plants and ready-mixed concrete facilities, while over 100,000 trees have been donated to municipalities, communities, customers and to the Greek state.

Jan 1, 2002