Search Documents

By T. E. Mccandless

Detrital minerals of mantle origin have been found in the Green River Basin of Southwestern Wyoming (Figure 1). Pyrope, pyrope-almandine, and chrome-bearing clinopyroxene and orthopyroxene occur on the antmounds of Pogonomyrmex Occidentalis. These antmounds are a common sight throughout the western U.S., and were used by early paleontologists as fossil mammal collection sites. The mound is composed of two types of material; (1) soil excavated during the digging of the nest below the surface (maximum depth 3 meters) and (2) larger grains collected from the surface and placed on the mound, probably to prevent erosion. The selection of grains to armor the mound seems to be based largely on the mean diameter of the grain, with other factors such as weight, sphericity, roundness and composition in decreasing order of importance (Wheeler and Wheeler, 1963). The minerals of this study happen to fall within that mean diameter range. The garnets are found on the mounds as 3-6 mm diameter subrounded to subangular grains. The pyroxenes are also 3-6 mm in diameter and are most commonly subangular laths. The minerals themselves show evidence of abrasion, such as frosted surfaces and rounded edges. Orange peel texture is present on some of the grains, which suggests that kelyphitic rims were once present, but have been removed. Also, no similar minerals were found in sieved soil auger samples to depths of 2 to 6 meters taken near the antmounds. These observations imply a distal rather than proximal source for the minerals. Lamproitic rocks of upper mantle origin are found bordering the "Green River Basin. The best known are the Leucite Hills, a series of ultrapotassic volcanics found on the north flank of the Rock Springs Uplift (Carmichael, 1967). Minor occurrences of mica peridotite and ultrapotassic volcanics are also found on the western end of the Uinta Mountains in Utah (Best, et al, 1968). None of these rocks are known to contain minerals like those on the antmounds. The garnets are comprised of purple chrome pyrope, red chrome pyrope-almandine, and pink to orange low chrome pyrope/pyrope-almandine. Oxide statistics for these groups are summarized in Table 1. These three groups are distinct when their Cr203 values are plotted against magnesium number (Figure 2). The chrome pyropes are highest in Cr203 (1.28-2.66%) and have high, restricted Mg number values (0.781-0.826). The chrome pyrope almandines have similarly high Cr203 (1.29-2.62%) but a lower Mg number range. The low chrome pyrope/pyrope-almandines have the lowest Cr203 content (0.09-0.73) and the widest Mg number range (0.534-0.836). Using the classification scheme of Dawson and Stephens (1975) the chrome pyropes are most similar to garnets derived from kimberlite and from garnet lherzolite, websterite, and harzburgite xenoliths in kimberlite. The chrome pyrope-almandines and the low chrome pyrope/ pyrope almandines are similar to garnets derived from eclogite nodules (Figure 3).

Jan 1, 1984

By C. I. Richman

The E h potential during of a iron reducing bacteria such as Aquaspirillum Magnetotacticum (A.M.) can be predicted by a growth model. It also reflects the adsorption of Fe+2 Cu+2 and Mn +2 ions, that can be incorporated into magnetic material called magnetosomes. The Ferric ion concentration during controlled growth of Thiobacillus Ferrooxidans (T.F.) is a function of the bacteria population curve, while A. M. ferrous ion concentration is a function of the integral of the population curve. Charting of the redox potential of T.F. during batch oxidation of refractory ores such as pyrite and pyrrhotite can be helpful to establishing onset and rate the bulk bio-oxidation rate. The onset of biooxidation is marked by an increase in Fe +3 ions that can be correlated with increased growth due to adsorbed electrons.

Jan 1, 1998

By PDF

Flotation columns are widely used in mineral processing and coal preparation industry today. Mathematical modeling of flotation columns has conventionally been done using axial dispersion or tank-in-series models. However, for design and scale up purposes these models are not adequate enough because they do not provide detailed information of the flow fields within the column. This paper presents a Two-Dimensional, Two-Phase. Fluid-dynamic Model and its numerical solutions for some cases encountered in column flotation. The MAC (Marker and Cell) method was employed to obtain the numerical solutions, and based on this method a computer code COLUMNFLOW was developed. The simulated flow field reveals the presence of a circulation flow structure in flotation columns, which could be one of the main reasons for mixing in column flotation. The effects of some parameters such as superficial gas and liquid velocities on the characteristics of the flow structure in flotation columns were also tested with the numerical model.

Jan 1, 1994

By Jorge Amaya, Nelson Morales Varela, Francisco Saavedra, Gonzalo Nelis, René Gómez

Precedence constraints are broadly used in mathematical models and algorithms for mine planning to model, for example, slope angles in open pit operations or connectivity in underground mines. Unfortunately, these constraints do not capture relevant geometrical aspects for the design of the mine like minimum bottom space of pits or smoothness of the economic envelope in block caves. In this work, we present different approaches that utilize precedence constraints generating economic envelops that are more suitable for design purposes. The numerical experiences show that the proposed techniques produce high value envelops with better geometrical properties and that the methods proposed can be computed efficiently.

Jun 25, 2023

By Ihsan Berk Tulu, Ted Klemetti, Deniz Tuncay

Accurately estimating load distributions and ground responses around underground openings plays a significant role in the safety of the operations in underground mines. Adequately designing pillars and other support measures relies highly on the accurate assessment of the mining-induced loads, as well as the load-bearing capacities of the supports. There are various methods that can be used to approximate mining-induced loads in stratified rock masses, both empirical and numerical. In this study, the numerical modeling approach recently developed at West Virginia University, which is based on the modeling approach developed by the National Institute for Occupational Safety and Health (NIOSH), is investigated using the finite difference software FLAC3D. The model includes the longwall panels, the adjacent chain pillar systems, and the different stratigraphic layers of the overburden. Using the 3D model, changes in loading conditions and deformations on the areas of interest, induced by an approaching longwall face, can be examined. This paper details the 3D modeling of a longwall panel utilizing this approach, and the verification of the results against field observations. The studied panel was 360 m wide with a 3-entry chain pillar system and about a 160-m average overburden depth around the studied area. The overburden strata consist of alternating layers of shale, sandstone, and limestone. The FLAC3D results were compared against field measurements from the mine site. The stress change values measured in the chain pillars were comparable with the modeling results. The model also replicated the surface subsidence profile obtained from field measurements fairly well. Overall, the 3D modeling approach was found to be successful for the case study longwall panel.

Sep 23, 2020

By Hesam Dehghani, Farid Alimohammadnia, Nima Babanouri, Mokhtar Kalhori

In open-pit mining, blasting pattern design is performed to achieve a desired degree of fragmentation for loading, hauling, and crushing operations. Inappropriate fragmentation of rock will result in numerous problems such as incurring extra costs for secondary blasting, production interruption, etc. Wetness of the blast holes is one of the most important factors, which can cause the inappropriate rock fragmentation. Lowering ambient temperature in the vicinity of the explosion, the presence of water in the hole adversely affects the quality of the explosive while dissipating part of the explosion energy, ending up with inappropriate fragmentation problems. In the present research, in order to study blast-induced fragmentation conditions in Baba-Ali Iron Ore Mine, three scenarios were considered: explosion of ammonium nitrate with fuel oil (ANFO) in dry hole, explosion of ANFO in wet hole, and explosion of the emulsion in wet hole. For this purpose LS-DYNA, a numerical simulation code was used. Results of the present research showed that, compared to the explosion of ANFO in wet hole, the explosion of the emulsion produced more uniform distribution of fragment size, while the explosion of ANFO in dry hole resulted in fewer large fragments.

By D. M. Hausen

A quantitative x-ray diffraction method has been developed for the analysis of alteration minerals in wallrock. Alteration data are plotted and contoured (analogous to geochemical data). Alteration trends outlined by this technique correlate closely with geochemical anomalies, and in some cases attend well beyond the perimeter of anomalous base metal values. "Monomineralic contouring," applied originally to porphyry-type mineralization, has been extended to other types of mineralization, including volcanogenic massive sulfide deposits. Equipment and techniques used in the quantitative measurement of alteration mineralogy are discussed.

Jan 1, 1978

By Keros Cartwright

Sanitary landfilling has become one of the most widely used methods of disposing of solid refuse. A principal concern of regulatory agencies and the public itself is that landfill operations do not degrade the physical environment, including water resources, and the ground-water reservoir in particular. Ground-water and engineering geology can guide landfill operations into suitable terranes or develop measures to compensate for any natural limitations at a particular site Experience and research in Illinois suggest four activities relating to landfill disposal that warrant attention by geologists and engineers: (1) Regional delineation of favorable and unfavorable hydrogeologic conditions to facilitate planning and preliminary screening of potential landfill sites. (2) Site evaluations, with considerations of geologic materials, topography, water levels, flow systems, and local occurrence and use of water resources. (3) Re- search on aspects of the hydrogeologic environment that control effects of, or are modified by, landfills. (4) Formulation of practices in the siting, construction, and operation of landfills that prevent, mitigate, or isolate deleterious effects. The first two activities are basically in the domain of earth science, requiring the application of fundamental concepts of geology and hydrology and conventional site-exploration methods. The third activity, research, requires contributions from geology as well as other disciplines, including soil physics, sanitary engineering, and chemistry. The fourth calls for policy decisions by regulatory agencies and elected officials, using the contributions of scientists and engineers.

Jan 1, 1970

By M. D. Johnson

The San Andres mine, located in the western mountain region of Honduras, Central America, contains epithermal gold mineralization as disseminations, in quartz-chalcedonic veins and stockworks. Host rocks include a thick sequence of Cretaceous to Tertiary conglomerates, sandstones, rhyodacite tuffs and andesites. Mineralization is controlled by northwest and northeast striking, normal faults and fractures which dip steeply east and west. Currently, 500 STPD of 1. 93 Grams/MT gold ore is being open-pit mined from the conglomerate and andesite. The mine is at the west end of a mineralized zone that can be traced over an area of approximately 1.5 square kilometers.

Jan 1, 1993

By Jordan Hoover, Erika Moonin, Chuck George

"In response to a severe regional drought and in preparation for the further decline of water levels in Southern Nevada’s Lake Mead, the Southern Nevada Water Authority (SNWA) built a new intake system to ensure water supply to Las Vegas and its surrounding communities. In 2015, design began on the Low Lake Level Pumping Station (L3PS) that will move the water from this lower intake, ensuring operability of the water delivery system despite these declining lake levels. The L3PS Project includes a 159-meter-deep shaft, a large underground chamber, and 34-each 152-meter-deep, 2.4-meter-diameter drilled well shafts to be constructed in highly faulted and fractured ground. The Construction Manager at Risk (CMAR) delivery method was chosen to facilitate early contractor involvement in the design process to address the significant challenges and risks anticipated on this US$650 million Project. This paper describes the CMAR selection process; the CMAR involvement during design and benefits resulting from that involvement; and the unique collaborative effort among the owner, engineer, program manager and CMAR used to evaluate and select the best design approach, preferred underground construction methods, and coordinated geotechnical baseline report. PROJECT BACKGROUND AND NEED Seven of the United States’ western states rely heavily on the Colorado River and its tributaries for their water supply. The primary source of water for the Colorado River is winter snow that falls in the mountains ringing the Colorado River Basin. Flows in the Colorado River vary significantly from year to year, depending on the amount of snow and rain deposited in the basin. Beginning in the year 2000 and continuing to the present, snowfall has been well below documented historical averages and Colorado River flows have diminished."

Jan 1, 2016

By A. Hammons

Automated temporary roof support (ATRS) systems have been incorporated into roof bolters since the 1970's. During roof bolting, many injuries have occurred from large pieces of draw rock falling inby the ATRS beam and tipping back into the operator's area. Other injuries have occurred due to smaller, sharp rocks falling onto the operator's hand and arm during initiation of roof bolt drilling. These injuries are attributed to weak immediate roof, sometimes called roof skin failure. Even though ATRS systems support the roof and provide a measure of protection against roof skin failure, additional hazards sometimes do exist immediately inby and outby the supported roof. Design innovations such as the ATRS mounted rocker pad deflector systems have been designed to improve the roof bolter operator safety. This paper will inform the reader of the hazards, machine evolution through different design solutions, and the current state of the art in preventing roof skin failure injuries when roof bolting.

Jan 1, 2009

By R. Bishop, J. Baggett, J. Monsalve, J. Hole, N. Ripepi, A. Abassi

This work focuses on the operational and safety issues associated with karst voids in large opening underground mines. Issues include water inrush, structural instability, and engineering uncertainty in these environments. Coupled with the fracturing prevalent in folded sedimentary rocks, karsts are complex and challenging ground control risks. Traditional methods of predicting karst locations, such as probe drilling, are impeded by the inconsistent spatial distribution and variable sizes of the features. Ground penetrating radar (GPR) is a geophysical technique that transmits radio waves into a medium and subsequently detects reflected waves via a receiver. The travel time and energy of received signals are then processed and interpreted. The difference in material properties between limestone and open karsts causes strong reflections. GPR is frequently used as a geophysical surveying technique in several industries, however there is a lack of published research on underground mining GPR applications. The purpose of this work is to prove the viability of GPR in underground stone mines for karst detection, and to discuss the importance of karst detection ahead of mining. INTRODUCTION The Mine Safety and Health Administration (MSHA) currently lists 116 active underground stone mines in the United States, the vast majority of which extract limestone for crushed stone products. These limestone mines have the potential to encounter karst voids at some point in their operation, as most karstic regions of the United States develop in limestone rock masses (Kuniansky, Weary, & Kaufmann, 2016). Karsts, the cavities formed by the dissolution of carbonate rock, have long plagued the mining and tunneling industries, as well as been a hindrance on the Earth’s surface, producing sinkholes and ruining otherwise valuable land for construction and public use. The impact of karsts on the Gavarres tunnel in Spain is well documented by Alija et al; constant instability conditions, material spills into the tunnel, and unexpected cavities seriously delayed the project deadlines and “were not foreseen in the design” (Alija, Torrijo, & Qunita-Ferreira, 2013). At the water supply project in Sohngua River, China, Bin et al detail the presence of both water and sediment filled karsts which are sources of disastrous conditions at this tunnel (Bin, et al., 2017). A hydrological tunnel in Lebanon encountered numerous massive karsts in the tunneling path which required remediation via friction anchors, rockbolts, welded wire fabric, channel steel arch segments, invert steel beams, and shotcrete (Leech, Jaoude, & Ghanem, 2008). From a design standpoint, rock mass classification schemes, such as the RMR from Bieniawski and the Q-system from Barton, are not able to represent the true nature of a karstified carbonate rock mass, and therefore complex case-by-case analyses of underground conditions are necessary (Andriani & Parise, 2017).

Jan 1, 2019

By William J. Miles

The inhalation of dust has been a problem in the mining industry since antiquity. Crystalline silica is now known to be the cause of silicosis, a form of pneumoconiosis that is associated with excessive exposure to respirable particles in some mining and industrial environments. Crystalline silica was reviewed by the International Agency for Research on Cancer (IARC) in 1986 and classified as a Group 2A, Probably Carcinogenic to Humans in Volume 42 and Supplement 7 of the IARC Monographs (1987). In 1996, IARC reviewed additional literature and studies published in the intervening decade and recommended that quartz and cristobalite, two polymorphs of crystalline silica, be listed as Group 1, Carcinogenic to Humans. Their recommendations and reclassification were published in 1997 in IARC Monographs 68.[2] In both Monographs, IARC classified amorphous silicas as Group 3, Inadequate Evidence for Carcinogenicity to Humans.

Jan 1, 1998

By S. K. Kawatra, J. A. Halt

"INTRODUCTION Iron ore beneficiation needs advances in areas such as process control, automation, burner and furnace designs, silica-free binders, and even alternative iron making routes. While some – like new binders – are only step-changes, all are tools that can help make the ironmaking industry more sustainable. This paper focuses on binders. Binders are added to iron ore fines before they are agglomerated. Binders are used to control the balling process and increase the mechanical quality (e.g. strength) of green-balls and pellets. Agglomeration usually follows thickening and filtration. Good-grade ores, which don't require upgrading, are wet ground to decrease particle size and increase specific surface area. Low-grade ores are often extensively upgraded through wet operations (flotation, dispersion and selective flocculation, magnetic separation, etc.). For both types of ores, thickening and filtration conclude the circuits so that moisture contents are lowered and the ores can be agglomerated. It's been known for a long time that thickening and filtration behaviors are influenced by zeta potential (Sandvik, 1979). Highly-negative zeta potential is good for dispersion while low zeta potential is good for filtration. So, the zeta potentials of iron ore particles are lowered with additions of acid or carbon dioxide, for example, to increase filtration rates and throughputs (Eisele et al., 2005). What happens to particles as their zeta potentials are lowered? Particles aggregate together, effectively forming larger particles. How stable then, are those aggregates during mixing and balling? Are they easily broken up during mixing (if mixers are even used)? Are they broken up during balling? Or, do the aggregates resist breakage so that the availability of ultra-fines, which are so beneficial for agglomeration (Stone, 1968), is decreased? For plants where high doses of bentonite are used as binder, the above questions may be of no concern. The bentonite adds the necessary amount of fines; however, even at those plants, the calcium and magnesium contents in the water affect bentonite's effectiveness (more magnesium and calcium means less effective bentonite). (Engesser, 2003) For plants where new silica-free organic binders are being developed and used, the above questions may need to be considered. The binder is only amongst the iron ore particles for a short period of time – until it burns away or thermally decomposes in the induration furnace – so the liberation, availability and distribution of fine particulates is very critical for the quality of balls and pellets. It was hypothesized that high zeta potential conditions would lead to good pellets, while low zeta potential conditions would lead to relatively bad pellets."

Jan 1, 2018

Grinding and energy input in stirred media mills are studied as functions of grinding time, stirring speed, media size and density, solid concentration, impeller and tank dimensions and design, and other relevant variables. Ground product size and surface area are determined with respect to the above variables. Changes in energy input and media/pulp rheological properties during grinding are described. The best conditions for grinding limestone in the laboratory stirred media mills have been identified. Equations for correlations involving power and modified Reynolds numbers have been established.

Jan 1, 1995

By A. Khan

The effect of sulfur dioxide on collectorless and collector induced flotation of chalcopyrite was studied by cyclic voltammetry on a rotating disc electrode. Contact angle measurements were made to determine the effect of sulfur dioxide concentration and electrochemical treatment. The benefits of sulfur dioxide in enhancing the selectivity of separating chalcopyrite from complex sulfide ores are discussed.

Jan 1, 1996

By Rodrigo Peroni, Vitor Campos

Carajás is one of the largest open pit mines in the world. The mine is comprised by a haul road network more than 100 km long, where the need for good roads is paramount and determining of the truck performances. This work integrates, regarding the ultimate pit design, an approach to consider an economic value to an originally unfit material, assuming it has the appropriate characteristics for haul road construction, which sometimes lies over economic iron ore. This measure demonstrated an improvement in the utilization of resources and guarantee the necessary material to the haul road design and Mining Pads maintenance.

Jun 25, 2023

By Kadri Dağdelen, Matthew Deutsch, Thys Johnson

Nested pit analysis in open-pit long range mine planning is used to define approximate ultimate pit limits and an initial high-level schedule in the early stages of a project. Modern ultimate pit optimizers can solve for dozens, or even hundreds, of nested pits however often a smaller subset of pits which are evenly spaced with respect to contained tonnage are desired for downstream analysis. In situations where that pushback selection process must be automated, such as when performing sensitivity analysis, or when the best subset of pushbacks is required; an optimization procedure is warranted. This paper describes a dynamic programming algorithm for selecting pushbacks following nested pit analysis, which is performant and addresses a long-standing inconvenience faced by long range open-pit mine planners.

Jun 25, 2023

By J. A. Barrera-Godinez

Traditional batch flotation tests produce a limited number of data points from which to evaluate the kinetics of the process. In this research, continuous weighing of froth, from a modified circular flotation cell, using a computer/data acquisition system., has been coupled with chemical analyses from intermittent froth sampling. This combination has permitted the experimental data to be smoothed such that the flotation kinetic parameters could be determined with enhanced confidence. To demonstrate the procedure, a galena ore was floated to permit flotation kinetics to be investigated as a function of cell parameters. It was shown that the kinetic data of this lead flotation most closely correlated with the Huber-Panu three parameter model. In addition the results illustrated the effect of froth thickness, froth scraper rate and air flow rate on the cell performance, in terms of mass flow, grade and recovery.

Jan 1, 1990

By R. Rodgers

The Pinto Valley Concentrator of BHP Copper Inc. restarted its sulphide mining operations in September 2007 to produce copper and moly concentrates. During the plant production ramp up, the copper/moly circuit quickly reached the copper grade and recovery targets, but the production and quality of the moly concentrate continued to be a challenge. Even though several improvements in the moly circuit were completed, the final moly concentrate did not meet contractual specifications. After reviewing several options to improve grade and reduce contaminants, the installation of three flotation columns was chosen. The column design and construction were done utilizing in-house craftsmen and engineers. Ten days after commissioning, the columns successfully reached a steady operation and began producing moly concentrate to the required specifications, that is, high moly tenors and low copper and iron content. In this paper, the operating parameters, mass balance, design, installation, commissioning and operation of the new flotation columns will be discussed.

Jan 1, 2010