Search Documents

By Ananta L. Yennamani

Blast movement measurement (BMM) transmitters are a practical method to measure three-dimensional (3D) rock movement because of blasting. The BMM transmitters are activated, programmed and installed in specially designed drill holes prior to the blast and the BMM detector locates the transmitters after the blast. The BMM software then calculates and summarizes the 3D movement of each BMM transmitter ball. This information helps to redefine the ore and waste boundaries and enables improved ore and waste selection, resulting in a genuine step change in grade control. The BMM program was carried out at Newmont Mining Corp.?s Phoenix Mine, in northern Nevada near the town of Battle Mountain. The mine is in a historic mining district that contains gold, silver and copper. The geology of the pit consists of different formations made up of sandstone, siltstone, limestone, chert-pebble conglomerate, shale, skarn and quartzite, to name a few. Some of the rock is extremely hard and a powder factor of up to 0.5 kg/t (1 lb/st) is required to get adequate fragmentation to ensure sufficient throughput through the crusher and the mill. The result of using such a high powder factor translates into considerable blast movement and heave. This movement means that the ore/waste digging polygons estimated by the ore control engineer from sampling the initial blast holes will no longer be located in their original posi-tions. The purpose of this project was to test the measurement method and to see if locating the digging polygons in the broken muck pile and excavating to those polygons will improve grade control through the mill. Case studies (Zhang, 1994), (Taylor, 1995), (Gilbride, 1995), (Harris, 1997), (Taylor, 2003), Barrick Goldstrike (Gold-strike Mine, 2008), Ruby Hill Mine (Hilkewich, 2009), (Porcupine Mine, 2005) and (Aguirre, 2010) have shown that, by accounting for the blast movement, there is a potential to increase mineral recovery by as much as 25 percent for individual blasts for only a modest cost increase.

Jan 1, 2011

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2018

By L. O’Connor, E. Tarshizi

The objective of this work is to provide a detailed review and a list of references in chronological order, comprising 80 recent technical papers, on the use of discrete-event simulation (DES) modeling in mining engineering. In this article, the review papers of published mine simulation projects through 2007 are summarized, and then a comprehensive review of individual articles published from 2008 to 2015 is presented. This survey work also includes analyses of the simulation tools used in the published projects, mining types and applications in order to assess these key features and evaluate the recent state of research in mine DES simulation. In addition, an interactive map visualization for the locations of the simulated projects is made available on a website to benefit current and prospective scholars in the field. The results of this investigation revealed that the most common application of DES in mining had been mining equipment selection and analysis, while ore processing and risk management projects were less frequently reported. The results also showed that modeling surface mines were in the majority, but the trend of publications for underground mine simulations had also increased. According to the results, ARENA was the most popular simulation software package, but several simulation tools that were only used once or twice in the mining projects are also included in this review.

Jan 1, 2017

By Richard L. Bullock

Believe it or not, mine evaluation and feasibility studies are as old as the industry itself. In the first recorded writing on mining by Agricola (1556), he gave several clues as what to look for in evaluating a mine, to determine if it was economically feasible. Below is the guidance from Agricola, with my interpretation of what he would include today. Now a miner, before he begins to mine the orebodies must consider seven things, namely: ? The situation (the geography/topography). ? The conditions (the geologic/mineralogic and mining conditions). ? The water (availability, hydrology and ownership). ? The roads (plus the railroads, power lines, all other infrastructure). ? The climate (the weather-rainfall/environment). ? The right of ownership (the land and legal entitlement). ? The neighbors (the social environmental concerns of the area). It is amazing how much of his guidance has not changed in 455 years. Yet Agricola gives no guidance on determining the correct cost, or determining the correct commodity pricing. But he does give a few words of caution on the related ethics involved on buying mineral properties: ?A prudent owner, before he buys shares, ought to go to the mine and carefully examine the nature of the vein, for it is very important that he should be on his guard lest fraudulent sellers of shares should deceive him.? Three hundred years later (1866), to further amplify this point, in the most famous thing that Mark Twain never said, as an introduction to a lecturer to an audience of gold-miners at Red Dog, CA, the famed author/humorist allegedly described a mine as ?a hole in the ground owned by a liar? (Farrar & Rinehart, 1935). So, one might conclude that between these two dates, the mining industry did little to improve its reputation. Unfortunately, since Mark Twain allegedly made those remarks, we have not done near enough to gain accountability for the mineral industry.

Jan 1, 2011

By Rahul Singh, Sunil Kumar, Erich Dohm, Maoming Fan

The rapid increase of P2O5 use for food, biofuels, and LiFePO4 batteries etc. accelerates the depletion rate of phosphate reserves. In the phosphate industry, a significant amount of ultrafine phosphate has been discarded as slime tailing due to processing difficulties. The major problems associated with ultrafine particle flotation are low probability of bubble-particle collision and adhesion, and high probability of unwanted gangue particles entrainment. This paper investigates the enhanced ultrafine phosphate particle flotation probability by Eriez’ CavTube generated fine/ ultrafine bubbles and the improved flotation selectivity by wash water etc. Ultrafine phosphates with various gangue minerals of quartz/muscovite, calcite/dolomite, and iron/ silica were studied. Microscopic observations show that the entrained ultrafine gangue minerals can be minimized by using wash water in column flotation. A three-factor threelevel central composite experimental design was conducted for ultrafine phosphate flotation. For comparison, both benchtop mechanical cell and laboratory column flotation tests were performed at their optimal respective flotation conditions. Using Eriez CavTube column flotation technology for Industries Chimiques du Senegal (ICS) ultrafine slime tailings, a concentrate grade of 36.0% P2O5, was achieved at 89.4% P2O5 recovery. Improved flotation performance was achieved using column flotation as compared to benchtop mechanical cell flotation. The benefits of Eriez’ column flotation technology realized from this study include the high P2O5 grade and recovery.

Feb 1, 2024

By James G. McKelvey

Owners have seen several major tunnel projects in recent years fall victim to a general reduction in the number of bidders as well as an erratic range of pricing. It should be noted though that this is not a universal trend and some projects have seen good competitive bids. Contractual terms and conditions are an important factor in attracting good competition. The Front End documents of tunnel projects have come under increasing scrutiny as tunneling contractors in the U.S. industry are looking much more closely at their risk exposure in the contract terms and conditions. Considering the amount of tunnel construction work upcoming in North America, it is important that General and Special Conditions are put together in a way that provides a reasonable basis to execute the Contract and also provide a fair, balanced and swift way to resolve disputes.

Jan 1, 2008

By Behrouz Tehrani

The size, complex issues, and requirements to construct large number of tunnels, for a single project, expeditiously, and without exceeding the overall project budget, a program Construction Management (CM) team is highly recommended to be selected early during design process to provide guidance/direction relative to contract packaging and scheduling. This paper is not focused on the project itself, however, the emphasis is on experiences gained from the project. Wishing that some of the strategies described in this paper will be of value to owners of underground project.

Jan 1, 2008

By G. F. Revey

All underground operations have limiting factors that influence overall profitability. Hoisting, hauling, available headings, labor, milling capacity and other factors limit how much material can be removed from an underground mine. Consequently, when mines use limited labor to handle the additional rock from overbreak and to perform extra ground support tasks, productive activity is replaced by non-productive work. Mining economics are further penalized when overbreak causes dilution of ore grades. This paper reviews organizational systems that mines have used to create environments which foster the creation of successful overbreak control programs. Actual case histories document the various quality improvement techniques, worker incentives, and practical project management systems used by these mines. A brief review of controlled blasting technology sources and overbreak measurement tools is also included.

Jan 1, 1997

By Henning Schwarz, Ade Ogunsola, Anas Almousa

"The Riyadh Metro, commissioned by Arriyadh Development Authority “ADA” - the executive arm of The High Commission for the Development of Arriyadh -, forms part of a new public transport-system of Saudi Arabia’s fast growing capital city. The Design & Build project consists of 176 km of Metro Line with 57 km of tunnels. Beyond the Design and Construction, an additional aim of the ADA is to introduce up-to-date methodologies and improve safety in construction projects. A systematic dilapidation survey of buildings and infrastructures was a prerequisite for designing the required instrumentation and monitoring tools. Site investigations required of existing methodologies and the use of geophysical methods for achieving reliable results. Large diameter TBM tunneling is challenging in hot weather conditions and karstic ground. The present paper shows how modern technologies for underground construction are introduced into the local industry and gives an outlook on future projects in the Kingdom of Saudi Arabia. INTRODUCTION Riyadh, the capital city of the Kingdom of Saudi Arabia, is a fast growing city with more than 5.7 million inhabitants. The growth of the city is linked to the recent history of the Kingdom, where some initial milestones from the 1950’s can be highlighted: Revenue generation from the exportation of oil from the Kingdom; downstream investment of oil revenue in the reconstruction and development of the Kingdom; a general plan for the settlement of the Bedouins; the provision of a public electricity network for the city; the opening of the Riyadh - Dammam railway corridor providing a link from the capital to the Eastern Region; the commissioning of Riyadh airport (converted to Riyadh airbase, after the opening of King Khalid International Airport in 1983); and the relocation of ministries and other central government agencies in 1955. In 1974, The High Commission for the Development of Arriyadh was established as the organizational, planning, executive and coordinating body responsible for the development of Riyadh. Arriyadh Development Authority “ADA”, established in 1983 is the High Commission’s executive, technical and administrative arm. The ADA is responsible for implementing the High Commission's organizational, planning, executive and coordinating decisions and missions. The ADA’s president is a member of the High Commission (ADA 2015). One of the remits of the ADA is the preparation and execution of a transport plan for the city of Riyadh."

Jan 1, 2016

By J. Best, K. Gallant

This paper explores the age-old concept of mine-mill reconciliation from a new perspective. Advances in reconciliation processes have been slow to materialize because in the quest for “rightness”, engineers, geologists and metallurgists have become entrenched in their viewpoints, dutifully performing to the metrics and expectations imposed upon them by the siloed organization. Moreover, reconciliation has not been viewed as a primary value creator, but an accounting non-value added task. In reality, the knowledge from reconciliation can significantly enhance yields. Critical review of the direct variables (tons, grade, etc.) and other less-obvious variables (incentives, communication, etc.) reveal a complex web of barriers to be cleared by management in order to realize benefits. Also, mineralogical reconciliation methods may offer renewed faith in the process.

Jan 1, 2004

By Gerald H. Luttrell, Seyed Hassan Amini, Aaron Noble

One of the most important processing engineering tools for designing mineral processing facilities is linear circuit analysis. This technique, originally conceived and developed by Meloy, Williams, and Fuerstenau nearly four decades ago, provides fundamental insights regarding how unit operations interact and respond when arranged in multi-stage processing circuits. Researchers have successfully utilized this tool to improve the operating performance of industrial processing circuits incorporating coal spirals, magnetic separators, mineral spirals, and eddy current separators. More recently, advanced versions of this tool have also been developed to provide a standardized framework for circuit mass balance calculations, to output exact analytical solutions to mass yield and value-based efficiency expressions, and to estimate uncertainty propagation in separation circuits. This article reviews the historical development of linear circuit analysis, describes how the technique has evolved to address more complex circuit design problems, and presents industrial case studies that highlight the importance of this process engineering tool.

By L. Thompsen

High-pressure grinding rolls (HPGR) offer capacity increases, savings in operating costs and metallurgical advantages. The first installation of the Polycom HPGR in a copper ore treatment plant occurred in July 1995 at Cyprus Sierrita’s mining complex near Green Valley, AZ (Fig. 1). Until that time, the benefits this technology offers for copper and gold ore were only demonstrated on testwork. In other industries, such as diamonds, HPGR have proven to be reliable in industrial-scale plants and have set a new standard for this kind of ore treatment plant. HPGR are also successfully used for the comminution of coal, blast furnace slag and in cement and pelletizing plants. The installation at the Cyprus Sierrita Mine should prove the economical benefits in commerical-scale copper mining, confirming the results of comprehensive testwork(Fig. 2).

Jan 1, 1996

By R. D. Wunder

The Chino Mines Company, a Kennecott-Mitsubishi partnership, located in Hurley, New Mexico, recently completed a $405 million modernization of its mine, concentrator, and smelter facilities. The mine/ concentrator modernization commenced in 1980 and the smelter modernization began during 1982. Modernization of the mine and concentrator facilities involved increasing the mining rate from 98 kt/d (108,000 stpd) to 152.2 kt/d (167,800 stpd). Ore mining was designed to increase production from 20.2 kt/d (22,300 stpd) to 34.0 kt/d (37,500 stpd). A new concentrator was constructed near the mine using semi-autogenous grinding. The new smelter uses the INCO flash smelting process, increasing capacity by 40.8 kt/a (45,000 stpy) to 99.8 kt/a (110,000 stpy) of salable copper.

Jan 1, 1985

By Aleksandar D. Bugarski, Dylan A. Ritter

The results of laboratory characterization of tailpipe emissions for three “clean” engines that meet U.S. EPA Tier 4 final emissions standards were used to assess the viability and effectiveness of repowering existing engines and powering new mobile equipment with those engines as a control strategy for reducing exposure of underground miners to diesel aerosol and criteria gases. The evaluated engines were representative of those that achieve the emission standards through implementation of various in-cylinder emissions control strategies, use of crankcase filtration, and use of three types of exhaust aftertreatment systems: (1) diesel oxidation catalytic converter (DOC), (2) combination of DOC and the full-flow wall flow monolith diesel particulate filter (DPF), or (3) combination of DOC, diesel exhaust fluid (DEF) based selective catalytic reduction (SCR) system, and ammonia slip catalyst (ASC). The study showed that the highest reductions in concentrations of diesel aerosols in underground workings, in terms of both mass and number, could be achieved if the engines, preferably in all power classes, are fitted with viable DPF systems. The use of U.S. EPA Tier 4 final engines equipped with DOC and DOC/SCR/ASC systems could help operators to considerably reduce mass, but not number concentrations of aerosols. The emissions of two of the evaluated engines, one equipped with DOC and the other equipped with DOC/DPF systems, were characterized by substantial secondary NO2 emissions that would limit the viability of those engines for underground mining applications. It appears that the catalyst formulations used in the exhaust aftertreatment systems of the “clean” engines marketed to the underground mining industry need to be formulated to minimize the potential for generation of secondary NO2 emissions. The results indicate that the engines fitted with viable SCR/ASC systems present a low-NO2 alternative. All three “clean” engines were found to have low CO output. Therefore, due to nuances associated with the use of diesel-powered mobile equipment in underground mines, special attention needs to be paid to the selection and potentially optimization of “clean” engines for underground mining applications.

Feb 1, 2025

By Ross W. Smith

In recent years there has been a considerable amount of research work done relative to the effect of pretreatment and aging in water on the surface properties of both simple metal oxides and more complex oxides such as the silicate minerals 1-6. Of particular interest is the work of Somasundaran6 who states that after preparing minerals by size reduction and washing with dilute acids "... it is essential to treat it (the mineral) with water in order to remove any effects of leaching itself." Somasundaran also states, "... it is advisable to use a solution close to the point of zero charge for conditioning purposes." Parksl notes that, "Dehydration, dehydroxylation, and increased crystallinity can be expected to decrease the PZC. The presence of anionic impurities or of pH-independent potential determining ions will decrease the PZC. Cationic species will increase the PZC." Healy and Jellett4 believe that in the Zn0-water system "the surface charge of Zn0 in water and each pH is determined by the concentration and adsorption of each hydrolyzed (charged and uncharged) Zn(II) species." Finally, according to Parks 2, "The PZC of an unaltered com¬plex oxide in a system devoid of specific electrolytes is approximately the average of the PZC's of its component oxides... Equilibration with water results in loss of mono and divalent cations by exchange with H+, thus a loss of influence on the PZC by those cations, i.e., a shift in the PZC with time in the direction of that remaining oxide. The present paper investigates the change of point of zero charge (PZC) of a number of simple oxides and several complex oxides as a function of aging time in water. In some cases acid pretreatment of minerals was performed. However, in most cases the minerals were not acid pretreated. In several systems pH change as a function of aging time in water was monitored.

Jan 1, 1972

A new analytical approach for characterizing and improving the performance of ball milling is presented. Individual ball mill circuit design and operating variables can be related to overall circuit performance through two distinct parameters for classification and breakage. The ball mill circuit functional performance equation is presented. Applications in the industrial plant and in the research field are discussed.

Jan 1, 1990

By Shahab Alizadeh, Ahmad Khodadadi Darban, Mehdi Mohseni, Mahmoud Abdollahy

This study probed the selective separation of lanthanum and yttrium in a nitrate medium in the presence of aluminum and calcium impurities using di-(2-ethylhexyl) phosphoric acid (D2EHPA). The factors studied in a central composite design (CCD) included extractant concentration, pH, concentration ratio of total impurities to rare earth elements, and interaction of these three factors. The extraction mechanism and types of extracted metal-containing species were delineated by the slope analysis method. The obtained thermodynamic data showed that lanthanum and yttrium extraction by the D2EHPA extractant was exothermic. The extraction of both rare earth elements was accompanied by an entropy reduction. The negative magnitude of ΔS in yttrium extraction reaction suggests stronger D2EHPA-Y(III) complexation relative to La(III). As entropy decreased and enthalpy increased, the extraction process became unspontaneous. Using the proposed flowsheet, lanthanum and yttrium products with > 90% purity were obtained.

Aug 10, 2021

By James P. Rider

Significant advances in longwall mining technology and equipment have occurred over the last decade by the late 1990s, longwall mine output accounted for 40% of all underground output in the U.S. and today longwall mines account for approximately 50% of coal produced underground in the United states. A 51% increase in average shift production rates has occurred over the last 15 years. this increased longwall productivity has meant that far more dust is being produced and controlling respirable coal dust presents an ongoing challenge for coal mine operators the National Institute for Occupational safety and Health (NIOSH) conducted a series of benchmark surveys at longwall operations across the country to identify current operating practices and the types of controls being used. Gravimetric and instantaneous dust sampling was completed to quantify the dust levels generated by major sources on the longwall section and to identify different control technologies in use today substantial reductions in dust levels were realized at sampling locations on the face when compared with ongwall surveys conducted in the 1990s results from the underground dust surveys and current longwall dust control technology and operating practices will be discussed. Mining Engineering, 2011, Vol. 63, No. 9, pp. 74-80. Official publication of the society for mining, metallurgy and exploration, Inc.

Jan 1, 2011

By J. Drelich

The wetting behavior of liquid polymers at solid surfaces and the adhesion forces involved at polymer-filler interfaces should always be considered in the fabrication of high quality polymer composites, including those made with mineral fillers. Spontaneous polymer spreading over the filler surface is a basic condition in the fabrication of the polymer-mineral composites. In this regard, the wetting and adhesion characteristics of polymer-mineral systems are reviewed in this contribution. It appears that several aspects of wetting phenomena at mineral filler surfaces are not well described in the literature and require further systematic study. Specifically, it is clear from this review that efforts should be made to determine the effects of mineral surface contamination (including surface hydration) on wetting and adhesion phenomena, and to determine the wetting characteristics of molten polymers at mineral filler surfaces. It is expected that any improved fundamental understanding of wetting and adhesion phenomena for the polymer-mineral composites will provide the basis for further technological development.

Jan 1, 1995

By Basak Anameric

This study reports preliminary feasibility investigations for utilization of the selective carbothermic reduction and smelting (SCRS) processing scheme to beneficiate low-grade iron-manganese (Fe-Mn) mineral deposits from MN, USA. The study includes laboratory-scale demonstrations using an induction furnace and production of various products by manipulation of operational parameters. The products include alternative iron (Alt Fe), high carbon ferromanganese (HC FeMn), alternative silicomanganese (Alt SiMn), and upgraded manganese concentrate (Mn conc). All of these products have commercial value and can be used in various applications as raw materials.

Nov 23, 2020