Search Documents

By Antonio Nieto

According to the analysis of surface powered haulage accidents involving off-highway haul trucks in openpit mining, the U.S. Mine Safety and Health Administration (MSHA), reported 1,300 fatal accidents from 1990 to 2005. Of these, 163 were considered off-highway truck haulage accidents, and at least 23 involved collisions of an off-highway truck with a neighboring vehicle or a worker on foot (Nieto and Dagdelen, 2006). In general, an average of 18 nonfatal accidents and three fatal accidents occurred in openpit mining per year when equipment backed over the edge of an embankment, stockpile or dump point (Fessak, et al., 2003). The specific problems that need to be solved can be determined by carefully studying the accidents involving haulage trucks (Marrara, et al., 2004). Solutions to haulage truck safety must consider the human factors affecting each task even when engineering solutions seem most appropriate. In surface haulage, human performance becomes a critical issue because of the unusual demand the vehicle?s places on their human operators: ? Roadways and working areas change frequently in mining operations. ? The sheer mass of mining equipment such as trucks requires control inputs (e.g., braking) far in advance of the desired action. ? Rough roads, loading and unloading impacts can subject the driver to dangerous shocks and vibration. ? Visibility is sharply curtailed by the bulk of the vehicle generating large blind spots. All of the above issues can be attributed partially to the lack of visibility (Pyles et al., 2003). Driver visibility and communications are key issues to reduce mining truck accidents. Analysis of fatalities and injuries involving mining equipment demonstrates the need to develop new intervention and control strategies to mitigate the risks associated with mining equipment operation. Ongoing development of these and other new strategies is required to achieve a reduction of injury in the mining industry

Jan 2, 2010

A series of flotation experiments were carried out in a 2.25-dm3 laboratory-scale Rushton turbine cell using hydrophobic quartz particles. Flotation was performed at a constant mean bubble diameter over a range of superficial gas velocities and impeller rotational speeds. The overall flotation rate constant increased linearly with increasing superficial gas velocity (and hence bubble surface area flux). The rate constant also increased linearly with increasing energy dissipation, until a maximum value was reached. A further increase in energy dissipation had little effect on the rate constant. The dependency of the rate constant on energy dissipation is a reflection of the size range and hydrophobicity of the particles used in this study. The flotation rate constant increased with increasing particle size, except at the highest energy dissipation value examined, for which the flotation rate of the larger particles reached a plateau and, in some cases, decreased. Good agreement was obtained between the experimental results and those predicted by a fundamental flotation model using experimentally measured values for mean energy dissipation and the Sauter mean bubble diameter. The bubble velocity was adjusted to obtain the best fit to the experimental data. The inferred bubble velocity, based on the flotation model, was found to increase with increasing superficial gas velocity (and bubble surface area flux) and was found to decrease with increasing impeller rotational speed. While the inferred bubble velocities were significantly lower than experimentally measured bubble velocities, and, except at low superficial gas velocity values, significantly higher than the bubble swarm velocity calculated from gas holdup measurements, similar trends with impeller rotational speed and superficial gas velocity were observed in all cases.

Jan 1, 2007

By S. J. Benson

The Harts Range deposit, owned by Olympia Resources is located some 130 kms northeast of Alice Springs, in central Australia (part of Australia’s Northern Territory). The core economic minerals here are industrial grade garnet and alumino magnesio hornblende (AMH). The resource contains an estimated 2.3 million tonnes of recoverable garnet and 6.2 million tonnes of recoverable AMH, making Harts Range one of the most significant abrasive medium deposits in the world. Part of the general marketing axiom of Olympia Resources is to make high quality products from the garnet and also a special series of blended garnet/AMH products to match the needs for other sectors of industry. The deposit mineralization is of alluvial origin and thus, requires no significant liberation regimes. Over 50% of the head feed is in the form of SiO2/quartz and as much as 17% is –63micron clay slimes and mica. Original pilot scale testwork for flowsheet development centred around fairly conventional wet gravity systems, with spiral concentrators being the pre-eminent separating device. To a point, this type of flowsheet was going to achieve some of the aims albeit fairly predictably. The one area that this circuit would be very limited though is in the recovery of the very coarsest of the medium SG minerals. This was going to be a very important and longer-term costly flaw. Amongst the highest demand, greatest value of products to be produced will be the range of garnet & AMH in the +600 microns sector. A flowsheet dominated by spirals would be fated to forfeit a significant proportion of these coarse minerals to tails. At the Outokumpu Technology P/L test facilities in Perth, testwork was conducted using a pilot scale Floatex® Density Separator, the LPF-230 model. Using a twin stage approach, whereby a primary Floatex® underflow reports directly to a secondary Floatex®, recovery of the economically important +600 micron garnet was increased from 65% in the spirals-only flowsheet to 95% using the Floatex® based flowsheet. Finally, the other significant aspect of this approach is in substantial simplification of the circuit required and a huge reduction in plant footprint. Also, the nature of using hindered settling provides substantial opportunities for process control and automation.

Jan 1, 2005

By William Gleason

The numbers tell the story of this one. More than 50,000 people and 1,890 exhibitors took over the Las Vegas Convention Center Sept. 24-26 for the largest mining trade show in the world ? MINExpo. Inside the convention center, some of the largest machines used in mining were on display. Caterpillar, Liebherr, Komatsu and Hitachi displayed ultraclass offroad mining trucks and shovels. Atlas Copco and Schramm were among companies that rolled in mining drills and Bridgestone, Goodyear and Michelin were among the companies showing off the massive tires used by the trucks. Throughout the three halls and an outdoor display area, just about every kind of product, gadget or service used in the mining industry could be found on display somewhere.

Jan 1, 2012

By J. D. Doll

MSHA has promulgated a rule to limit the exposure of underground metal/nonmetal miners to diesel particulate matter (DPM). In May 2008, the final personal exposure limit will be lowered to 160 µg/m3 total carbon. To comply with this rule, mine operators are implementing a variety of control technologies. In this study two types of control technologies (ventilation and cabs) which are being implemented in limestone mines were investigated. Two stone mines in this study use large diameter propeller fans for main mine ventilation and direct the air to the faces using auxiliary fans, stoppings, and long pillars while bypassing the old mine workings. NIOSH measured for sub-micrometer elemental carbon (EC) using SKC DPM cassettes (analyzed using NIOSH 5040) and a near real time instrument. With the present ventilation and the number and type of vehicles used, the concentration of EC from DPM at the working areas was at or below 400 µg/m3 for both mines and about 166 µg/m3 and 251 µg/m3 at the returns. The real time data showed that the ventilation was reaching the working areas and effectively diluting the DPM. Environmental cabs were also used to reduce DPM exposures in three underground limestone mines. Using NIOSH method 5040 and near real time EC instrumentation, NIOSH sampled inside and outside of a loader cab at one of these limestone mines to determine the effectiveness of the cab. The cab was found to be over 90% effective in removing DPM as long as the cab system was properly maintained, and doors and windows were closed.

Jan 1, 2009

By R. V. Ramani, C. J. Bise

INTRODUCTION Classification of coal seams as thin, medium, and thick is both subjective and relative and is more a reflection of the statistical mode of the thicknesses en- countered in a mining region. A geological factor more precisely understood as defined than thickness is the inclination of the seams to the horizontal, commonly referred to as the pitch or the dip of the seam. Thick and steeply pitching seams present far more challenges to the ingenuity of the mining men to devise methods for their extraction than the thick and less steeply inclined ones. In a marginal case, where a thick coal seam may be minable by surface or underground methods, the decision bears a close relationship to the technological developments in the mining scene. Near surface thick coal seams are a special gift of nature and are not as wide- spread as the ones that call for the application of under- ground methods. Recent advancements in surface mining equipment have made it possible to surface mine to great depths. Stripping ratios of 30: 1 (cu yd of over- burden removed per ton of coal) have been achieved. The extraction of thick seams which preclude the use of surface methods is the concern of this chapter. Specifically, the objective here is to outline the special technological factors in underground mining of thick coal seams and to illustrate through several case histories the methods that are practiced in the North American continent. For the purposes of this chapter, a thick seam is defined as one which is not readily minable with currently available equipment without modifications to the extraction method or the equipment. At the present time, a thickness of 4.8 m (16 ft) can be considered as the lower limit, although developments in equipment and methods can be expected to push this limit upwards. The data for the case histories were collected from two extended mine visits in 1975 and 1978, and from other published accounts of the mines visited. Reference is drawn particularly to reports by Bise, Ramani, and Stefanko (1976) and Rarnani and Kenzy (1979). THICK SEAM MINING METHODS The various methods of mining thick seams can generally be grouped into three major categories: full face methods, where the entire thickness of the seam is re- covered in a single pass; slicing methods, where the seam is extracted to its full thickness by horizontal or inclined slices either in an ascending or descending order; and caving methods, where the seam is undercut and the en- tire coal seam is recovered by caving the top coal into the excavated cut, or some variations of the basic sub- level caving method. As shown in Table 1, in each of these methods, the coal is removed by either room-and-pillar or longwall methods. Hydraulic mining and transport of the coal in open flumes or in pipelines are also practiced. Addition- ally, the void created by the removal of coal may be filled with a packing material (stowing) except in the caving methods. The pitch (dip) of the seam, particularly when it is greater than 0.26 rad (150), imposes severe operational limitations on mobile equipment. A more detailed general discussion of the methods can be found in Bise et al. (1976) and Vorobjev and Deshmukh (1964). Specific discussion on the many variations of the three basic methods can be found in the papers presented at the international symposia that were held in

Jan 1, 1982

By Peter B. Dowden, Robert A. Robinson

Boulders, frequently found in tunnels excavated through soils, can pose major problems for full face TBMs in terms of slowing or halting the tunnel advance, cutter damage, and abrasive wear. The paper aims to consider the problem as a whole, from the geological characteristics of boulder sites, to the appropriate physical design of theTBM, and its operation in boulder-laden soils. In addition, visualization of boulders and other subsurface obstructions by seismic methods and ground penetrating radar are reviewed. The paper will assist the construction planner in assessing the risks and preparing appropriate specifications.

Jan 1, 2001

By S. Shaw

There is an increasing requirement for mines to meet a certain minimum criteria for sustainability within the context of the physical environment, ecosystem and socio-economic system in which they are located. The mining industry has wrestled to develop methods for assessing the ‘sustainability’ value of a mining project and indicators of ‘sustainability success’. A methodology for the evaluation of sustainability of a mining project using the Multiple Accounts Analysis (MAA) system was developed. The MAA is a platform for engagement of stakeholders and for the assessment of site-specific alternatives based on both qualitative and quantitative indicators of success.

Jan 1, 2004

By M. Nehdi

Deficient surface disposal systems of sulfidic mine waste often cause severe contamination of surface streams and groundwater reservoirs due to the oxidation of sulfide phases. The subsequent generation of leachates characterized by high acidity and elevated concentrations of toxic elements (commonly known as acid mine drainage) jeopardize the health of contiguous ecosystem. Stabilization/solidification (S/S) is recognized as a promising solution for treating such wastes. S/S processes generally mobilize alkaline and/or cementing materials/additives that act as neutralizing and/or binding agents. In the present research, industrial byproducts, namely, cement kiln dust (CKD) and Class C fly ash (FAC) have been used as candidate materials along with the partial addition of sulfate-resistant cement (SRC) in the S/S of polymetallic sulfidic mine tailings (MT). The effectiveness of S/S was assessed by comparing laboratory experimental values obtained from unconfined compressive strength, hydraulic conductivity and leaching propensity tests of S/S samples with regulatory standards for safe surface disposal of such wastes. Despite general regulatory compliance of compressive strength and hydraulic conductivity, some solidified/stabilized-cured matrices were found unable to provide the required immobilization of pollutants. Solidified/stabilized and 90-day cured mine tailings specimens made with composite binders containing (10% CKD + 10% FAC), (5% SRC + 15% FAC) and (5% SRC + 5% CKD + 10% FAC) significantly impaired the solubility of all contaminants investigated and proved successful in fixing metals within the matrix, in addition to achieving adequate unconfined compressive strength and hydraulic conductivity values, thus satisfying U.S. EPA regulations. Laboratory investigations revealed that, for polymetallic mining waste, leachate concentrations are the most critical factor in assessing the effectiveness of S/S technology.

Jan 1, 2008

U.S. Borax’s mine in California’s Mojave Desert is the source of nearly half the world’s supply of refined borates. These minerals are used in hundreds of products, including essential plant nutrients that increase crop yield and quality, and safe building products that protect homes from insects and the elements. Borax’s workforce is also safe. In fact, it is among the safest in the nation. In 2003, the company was recognized by the U.S. Mine, Safety and Health Administration (MSHA) for achieving the best safety record among large U.S. mining operations. It was also recognized by its parent company, Rio Tinto, for achieving the best record among its nearly 80 worldwide mining operations. Borax’s safety performance is five times better than the national average. And its workforce recently achieved more than two million hours without a lost-time injury.

Jan 1, 2004

By Shimi Tzobery, Jay Davenport, Raymond Henn, Sam Bandimere

Over the past several decades, the use of cement-based grouts using ultra fine cement as a replacement for portland cement has begun to gain acceptance as an alternative to chemical solution grouts used in permeation grouting. The amount of information currently available on grouts made with ultrafine cement is limited. The authors used a previously developed field testing program to perform additional tests to evaluate the permeation performance of portland and ultrafine cement-based grouts. For the first time, the 2003 testing program included an attempt to determine the 28 day compressive strength of the sand permeated by the grout.

Jan 1, 2005

By K. Norrena

Grade control in open pit mining requires the specification of dig limits that account for mineral grades, economic costs, and selectivity of mining equipment. Visual identification of ore rock types is ideal, but this is not always possible in lower grade disseminated deposits where ore/waste contacts are not visually discernible. In this case, conventional grade control practice consists of a two-step procedure (1) create a map of mineral grades at some selective mining unit scale, and (2) determine practical ore-waste boundaries or dig limits on the basis of the gridded block grades or assay information. This procedure is laborious, depends on a subjective assessment of where the boundary should be, and may be economically sub-optimal. We pose the determination of dig limits as an optimization problem and solve that problem with the technique of simulated annealing. Simulated annealing has the unique advantage of being able to combine multiple non-linear constraints into a single objective function. We use maximum profitability and the ability of the equipment to mine the proposed dig limits as constraints in the determination of optimal dig limits. We require a map of expected profit for eah block. Geostatistical techniques are recommended, for mapping expected profit but not necessary. Geostatistics will provide a quantification of the uncertainty in the grades within rock types using all available blasthole samples and exploration drilling. Some variant of L-optimal estimation or kriging can be used to determine the block-by-block classification that is economically optimum. We also need the expected profit for each block. It is unrealistic to assume free selection, that is, each block cannot be extracted independently of its neighbors. The optimal balance of ''accepting dilution'' and ''wasting ore'' is achieved to maximize profit subject to equipment constraints.

Jan 1, 2001

By G. A. Doyle

The quality of water in mine pit lakes depends in part on the physical limnology (Le. stratification, turnover, and development of anoxic conditions with depth) of the lake. Limnologic data collected from four existing pit lakes indicate that pit lakes develop a thermocline, or temperature stratification, in the upper 10m to 30 m of the water column. Two of the pit lakes (26 m and 55 m deep) undergo seasonal turnover of the entire water column, whereas two deeper pit lakes (110 m and 240 m) undergo seasonal turnover of only the upper portion of the water column. In the deeper lakes, seasonal mixing does not extend through the entire water column and a distinct chemocline develops with depth.

Jan 1, 1996

By K. Shoji

Residence time distributions (RTDs) were estimated by water tracing in a number of wet overflow ball mills (diameters 0.38 to 4.65 m) producing dense, coal-water slurries. In open-circuit mills of 0.38 m diameter and various length-diameter (L/D) ratios, the mean residence times of solid were also determined from measured mill holdups. Holdup increased with increased mill feed rate, but the mean residence times of coal and water were still equal to each other. The experimental residence time distributions were fitted to the Mori-Jimbo-Yamazaki semi-infinite, axial mixing model, and the dimensionless mixing coefficient was determined for each of 25 tests in single- and two-compartment mills. This coefficient was found to be independent of the feed rate but linearly proportional to the D/L ratio. The mixing coefficient was smaller for two-compartment mills than for single-compartment mills, showing that there was reduced mixing introduced by the diaphragm separating the compartments. Equations are given to scale residence time distributions for changes in mill diameter and length.

Jan 1, 2008

By Louis W. Cope

Since its discovery, Cuba has been called the “Pearl of the Antilles.” The country remains that, albeit a little tarnished these days. In Havana, many of the buildings are being refurbished, while some new ones are under construction. Since 1991, the laws have been relaxed so that Cuba is developing a mixed economy of central control with free market. Joint venture agreements have been signed with businesses from many countries. This does not include the United States due to its embargo. But even these regulations have been relaxed some.

Jan 1, 2003

By M. J. Sapko

The design requirements for mine ventilation seals have undergone a radical transformation in recent years, and these revisions have greatly increased the cost of the seal designs and their construction. For example, in the past two years, new federal regulations have increased the minimum design requirement to withstand explosion pressures from 138 kPa (20 psig) to 345 kPa (50 psig) or 827 kPa (120 psig), depending on whether the sealed mine volume is monitored continuously or not. Moreover, there is still a possibility that under certain conditions (such as detonations) even higher pressure requirements may be necessary. The ability of a monolithic, stand-alone mine seal to reliably withstand the full range of current and future pressures is becoming increasingly difficult and expensive. In an effort to develop a practical alternative, the West Virginia Office of Miners? Health Safety and Training (WVOMHST) and the National Institute for Occupational Safety and Health (NIOSH) have collaborated in a research effort to develop a practical, economic, and safe mine sealing technique that can enable mines seals to meet the full range of new explosion pressure design requirements. The basic idea is to use a barrier of common mine gob and rubble in combination with a conventional mine seal so that the pressure resulting from a gas explosion is reflected, absorbed, and attenuated, so the pressure on the ventilation seal is reduced. This paper discusses some concepts and preliminary test results for a ?Passive Mine Blast Attenuator? (PMBA) that can provide a useful alternative to increasingly larger and stronger stand-alone mine seals. Numerical models and full-scale experiments conducted at the NIOSH Lake Lynn Laboratory Experimental Mine (LLEM) show that the use of a PMBA can signficantly reduce the blast pressure and impulse on conventional ventilation seals. DISCLAIMER: This information is distributed solely for the purpose of pre-dissemination peer review under applicable information quality guidelines. It has not been formally disseminated by the National Institute for Occupational Safety and Health (NIOSH). It does not represent and should not be construed to represent any agency determination or policy.

Jan 1, 2009

By John E. Newby

Washington?s King County is constructing a new regional wastewater treatment facility, called Brightwater, in response to growth in the greater Seattle region. Planning conducted in the late 1950s identified the need for two regional treatment facilities. Constructed in the 1960s, these plants have served the region well. However, an eventual need for a third facility was also recognized. The Brightwater project implements the final phases of the long-term plan. The project includes a new treatment plant and an extensive conveyance system. When completed in 2010, the Brightwater facilities will treat sanitary sewer flows from growing populations living in northern King County and southern Snohomish County. The new system will fulfill commitments to provide wastewater services to local jurisdictions and sewer service providers in the King County Service Area. It will also provide more flexibility in the operation of the King County regional wastewater system. The Brightwater wastewater treatment plant will provide secondary treatment capacity using membrane bioractor technology in 2010 for 36 million gallons per day (mgd), with anticipated expansion in 2040 to 54 mgd, using membrane bioreactor technology. These capacities are for average wet-weather flows. The plant will also accommodate peak hourly flows of 130 mgd by 2010 and 170 mgd by 2040. The Brightwater Conveyance System consists of more than 8.1 km (13 miles) of tunneled influent and effluent conveyance lines, five tunnel portals/shafts, microtunneled influent and outfall connec-

Jan 1, 2007

By L. E. Eary, Andy Davis

The evolution of pit lake water quality depends on the lithology and hydrologic characteristics of the ultimate pit surface, the availability of buffering capacity in the wall rock vs. oxidizable sulfide content, the alkalinity of recharging groundwater and the evapo-concentrative characteristics of the system. This paper assesses the geochemistry of 11 existing pit lakes, ranging from the acid Red Hill and Berkeley pit lakes (pH 2.6 to 2.8) to the alkaline Yerington pit lake (pH 8.45). Predicted pit lake chemistry is similar to that in existing pits, with long-term chemistry lying on a geochemical continuum between end members that consist of influent calcium bicarbonate groundwater and naturally occurring sulfate-rich evaporite playa lakes.

Jan 1, 1998

In 2002 the authors updated the MFire model developed by the US Bureau of Mines. MineFire, developed by Mine Ventilation Services, Inc. (MVS), uses the MFire model to perform mine fire simulations on typical mine ventilation networks. The MineFire program is capable of producing visual schematics and other analysis tools for input and output of the MFire model. The MFire model, however, was limited to 500 branches and 10 fans. This paper discusses the newly modified MFire model that is now capable of modeling over 5000 branches and over 400 fans among other expansions and improvements. Given the long history and proven track record of MFire, the expansion did not modify the core calculation methods or results. This paper focuses on a general discussion of the MFire program and issues encountered in expansion of the algorithm. An example large network with simulation results is discussed.

Jan 1, 2011

By A. Cole, A. Bolland

The roasting and gas handling circuits at Goldstrikes' new Roasting Facility incorporate proven technologies in a unique combination. During the design of the plant, every effort was made to utilize the best available unit operations from the perspective of capital, environment and operating costs. The roaster utilizes Freeport-McMoRan whole ore roasting technology with pure oxygen as the oxidizing gas. This process was chosen based on its proven application on Carlin-type carbonaceous ores. An extensive gas cleaning train follows the roaster and comprises direct cooling, dust scrubbing, indirect cooling, wet electrostatic precipitation, mercury scrubbing, SO2 scrubbing, CO incineration and NOX reduction.

Jan 1, 2001