Search Documents

By A. P. I. Popoola, D. O. Okanigbe

Copper smelter dust (CSD) is a byproduct of copper smelting and is composed of considerable amounts of copper values and also contaminants (like silica and mullite). Silica in CSD forms Siloxane, a low density material, which is difficult to separate from the aqueous phase during solvent extraction. The need therefore arises to reduce/remove the aluminosilicates for better grade and recovery of copper in subsequent processes. This paper reports the use of two types of centrifugal gravity concentrators, namely Knelson (KGC) and Falcon (FGC), for upgrade of copper in CSD. The aim was achieved by an initial characterisation (Particle Size Distribution (PSD) and mineralogical analysis), together with Density Separation (DS) experimentation, premised on a hypothetical density difference between copper oxide and silicon/aluminum oxide. Wet screening results showed that 88.52 % of CSD particles were in -53 μm fraction. Further PSD study using laser diffraction showed the -53 μm fraction to be composed mainly of 26 μm, 22 μm and 18.5 μm fractions. Mineralogical analysis showed copper to occur mainly as oxides (24.34 wt%), but also as sulphides (7.95 wt%), and a substantial amount of aluminosilicates (42.97 wt%) were identified. Density of CSD was determined as 2.83 g/cm3. Copper content (18.02 wt%) in CSD was upgraded to 35.94 wt% in concentrate using KGC. In conclusion, the results showed good convergence between hypothesis and experiment. Additionally, it was also concluded that KGC performed better than FGC for copper upgrade in CSD. However, roasting CSD prior density separation was recommended for enhanced copper upgrade. Keywords: Copper smelter dust, density separation, solvent extraction, mineralogy

Jan 1, 2020

By A. Mboma

Keywords: Furnace, decommissioning, care and maintenance, re-start, funding, nickel Bindura Nickel Corporation (BNC) operates two nickel mines, and treats concentrates from these mines as well as toll concentrates from the region around its Bindura Smelter and Refinery (BSR) complex. At the smelter, concentrates of at least 5% nickel content are blended and dried to 4% moisture in a coal-fired rotary kiln. Matte smelting of concentrate is carried out in a six-in-line electric arc furnace, where the furnace slag is granulated and discarded. Furnace matte is transferred via ladles into Peirce-Smith converters, where, after granulation, a leach alloy containing 68%Ni, 20%Cu, and 6%S is produced. Converter slag is recycled via the matte-smelting furnace. The onset of the global economic recession towards the end of 2008 resulted in a collapse of metal prices, worsening the local situation that was already marred by unfavourable macro-economic conditions in Zimbabwe. As a result, BNC mines were put on care and maintenance in November 2008, followed by Bindura Smelter and Refinery in February and March 2009 respectively. The business environment has since changed, and BNC is getting ready to re-start the plant. This paper describes the decommissioning of the Bindura furnace, asset preservation during the care and maintenance programme in the past two years, and preparation for starting up of the Bindura smelter in the near future.

Jan 1, 2011

By R Kroukamp

Horizontal belt filters are typically used for separation of relatively free filtering solids where good post treatment is required. He horizontal belt filter is a continuous filter with an endless cloth supported on a grooved carrier belt. The belt and cloth are driven around two rollers across a series of evacuated suction boxes. The feed suspension is introduced at one end of the filter and deliquored to produce a cake at the other end. The benefits of using horizontal belt filters are good cake washing, continuous and visible processing, fully automatic operation, flexibility, high capacity and relative high speeds of operation. If required, horizontal belt filters enable efficient counter-current washings to minimize the usage of wash liquid. The horizontal belt filter has applications in the following: [? Metal concentrates ? Mineral sands ? Tailings ? Coal ? Iron ore ? Alumina ? Chloride processing ? Nickel and Cobalt refining ? Platinum group metals ? Zinc processing ? Many other applications in the Mining and Metallurgy industries ] 2. Operating Principle of a Horizontal Vacuum Belt Filter 2.1 Cake Forming The slurry to be dewatered is evenly distributed onto the filtering surface. Gravity assists the cake formation and the feed can be introduced in multiple stages. 2.2 Cake Washing Once the cake is formed, wash liquor/water can be introduced onto the top of the cake via a wash launder or sprays. Multiple wash stages, co-current, counter-current or direct washing can be added by increasing the length of the filter.

Jan 1, 2007

Decision-making regarding plant-scale reagent dosage regimes and air rates is a topic of ongoing investigation and high importance. The current work explains some techniques that have proven useful in deciding on plant-scale flotation operating regimes. Specific focus has been placed on the reagents: frother and depressant, as well as some discussion around the control of air rate and froth depth. Air rate has been selected based on its effects on the froth phase. Froth velocity and froth height above the cell lip are the two variables measured and used to select the operating air rate. Pulp level is then adjusted to increase or decrease mass pull. A technique has been developed using the Anglo Platinum Bubble Sizer on an industrial flotation cell to determine the relationship between bubble size and frother concentration. This technique has been extended to measure the equivalent frother concentration or frothabilities of various streams on a rougher bank. A mass balance for frother was performed successfully, and this provided a better understanding of the way frother moved in the rougher bank. With this knowledge, more informed decisions can be made about frother addition required in subsequent flotation stages. For depressant, a new protocol for deciding on dosage rate has been developed. The depressant dosage should be based on the amount of fresh feed material reporting to a bank. Currently 400 g per ton of fresh feed has been assumed a reasonable starting point, with promising results. Improved froth stability and grades were observed. There is scope for more accurately defining the optimal dosage rate. Importantly, the combined effect of changing the chemistry and the hydrodynamics together has been demonstrated. A significant upward shift in the grade-recovery relationship for a cleaner bank was observed.

Jan 1, 2013

By K. Sugawara, H. -S. Jeong, Y. Ishiguro, J. Otani, Y. Obara, A. Hirata

A series of measurements of induced stress by the Compact Conical-ended Borehole Overcoring (CCBO) technique was performed within rock mass around a tunnel excavated in a region that an underground powerhouse is constructed under high initial rock stress. In the measurements, a phenomenon of core disking was observed during overcoring. The selecting method of strain data uninfluenced by the core disking was proposed, using X-ray CT scanner. Then, the state of induced stress determined from the selected strain data was discussed, comparing with the state of initial stress. Eine Serie von Messungen von induzierter Belastung mit kompaktem konisch-beendetem Überbohrverfahren (CCBO) wurde in Felsmassen um einen Tunnel ausgeführt, der in einer Region gebohrt wurde wo ein unterirdisches Kraftwert unter hoher anfänglicher Felsbelastung gebaut wird. Bei den Messungen wurde beim Überbohrverfahren ein Phänomen des Core Disking beobachtet. Die gewählte Methode der Belastungsdaten, unbeeinflusst durch Core Disking wurde vorgeschlagen, unter Verwendung von Röntgen-CT-Scanner. Dann wurde der Zustand der induzierten Belastung aus den gewählten Belastungsdaten diskutiert, unter Vergleich mit der ursprünglichen Belastung. Une série de mesures de contrainte induite effectuée avec la technique de forage de sur-carottage compacte à embout conique a été exécutée dans la masse rocheuse autour d'un tunnel excavé dans une région de construction d'une centrale électrique souterraine sous haute contrainte de roche initiale. Au cours des mesures, un phénomène de discage de carotte a été observé pendant le sur-carottage. La méthode de sélection des données de contrainte non influencée par le discage de carotte a été proposée, en utilisant un scanneur de tomographie calculée aux rayons X. Il s'ensuit que l'état de contrainte induite provoquée et déterminé à partir des données de la contrainte sélectionnées a été traitée, en effectuant une comparaison avec l'état de contrainte initiale.

Jan 1, 2003

By Van Sint JanM., M. Prudencio

ABSTRACT We report the results of a model-testing program to evaluate the strength characteristics of non-persistent joints. We describe the conditions under which new tensile cracks generate and propagate to connect existing joints so that the rock mass becomes fractured into several blocks, leading to a low strength. The strength of some models was equal to that along a single joint through the full sample length. In models with two joint sets, failure took place along a composite plane, partly sliding along a discontinuous joint and shearing through the intervening intact block of rock, or else by rotation and sliding of the blocks. This last failure mode could also lead to very low model strength. ZUSAMMENFASSUNG Dieser Bericht beschreibt die Ergebnisse von Versuchen mit Modellfelsmassen um den Einfluâ von unterbrochenen Rissen in ihrer Widerstandsfähigkeit zu untersuchen. Es werden die Umstände beschrieben unter denen neue Zugrisse entstehen, sich verbreiten, sich mit bestehenden Rissen verbinden und die Felsmasse in mehrere Felsblöcke zerlegen und zu einer kleinen Widerstandsfestigkeit führen. Der Widerstand einiger Versuchskörper entsprach der Festigkeit eines Risses der die ganze Länge des Versuchskörpers überquert.Versuchkörper mit zwei Rißfamilien versagten unter einer zusammegesetzten Ebene, zum Teil mit Verschiebungen nach unterbrochenen Rißebenen die sich durch Schnittversagen intakter Felsblöcke verbinden, und zum Teil durch Drehungen und Verschiebungen einzelner Felsblöcke. Die letzte Versagunsart kann zu einer stark verminderten Widerstansfähigkeit führen. RÉSUMÉ Nous présentons les résultats de quelques essais fait sur des modèles évaluant les caractéristiques de résistance des fractures discontinues. Nous décrivons les conditions sous lesquelles des nouvelles fissures de traction peuvent s’engendrer et se propager pour faire la connection avec des fractures existantes, de façon que le rocher se fracture en plusieurs blocs, menant à une résistance réduite. La résistance de quelques modèles fut égale a celle d’une fracture traversant toute la longueur du modèle. Pour les modèles ayant deux ensembles de fractures, la rupture a eu lieu sur une surface mixte, causée d’une part, par le glissement sur une fracture discontinue et d’autre part, par la rupture à travers le pont de matériel intact; ou bien par rotation et glissement des blocs. Cette dernière façon de rupture peut aussi aboutir à une très faible résistance des modèles.

Jan 1, 2003

By J. P. Josien, J. F. Noirel, F. Lahaie, P. Bigarre, M. Al Heib

ABSTRACT: In June 2001, a fatal rockburst affected a longwall face in the Houillères du Bassin de Lorraine (HBL), France. Subsequently, a large operation of in situ stress measurements by overcoring was carried out with two main objectives: providing input data for the back analysis of the dynamic event and characterising the stress field in the next panels to be mined for identifying other potential high-risk zones. This paper makes a synthesis of the results of the overcoring tests performed and discusses those results in connection with the mining context, numerical model predictions, laboratory rock test results and microseismic activity. KEY WORDS: Mine, rockburst, stress, overcoring, measurement. ZUSAMMENFASSUNG: Im Juni 2001 hat ein Bergschlag eine Kohlengrube des Houillères du Bassin de Lorraine (HBL, Lothringen, Frankreich) schwer beschädigt. Nach diesem Unfall sind Spannungsmessugen durch Überborung durchegeführt worden, mit zwei Hauptziele : 1/ Daten zu liefern für die Retro-analyse des dynamischen Gebirgsschlag und 2/ die Spannungen in den zukünftigen Ausbauen so gut wie möglich zu charakterisieren, um eventuele andere Risikozonen festzustellen. Dieser Artikel stellt eine Synthese der erzielten Ergebnisse vor. Er diskutiert diese Ergebnisse in Verbindung mit dem gesamten Kohlengruben Zusammenhang, mit den Ergebnissen von numerischen Modellierungen, mit der Labor-Charakterisierung und mit der microsismische Überwachung. SCHLÜSSEL-WÖRTER: Kohlengruben, Bergschlag, Spannung, Überborung, Messung. RESUME: En Juin 2001, un coup de terrain a gravement affecté une longue taille aux Houillères du Bassin de Lorraine (HBL) en France. A la suite de cet accident, une importante campagne de mesures de contraintes par surcarottage a été réalisée, avec deux objectifs majeurs : fournir des données d’entrée permettant la rétroanalyse du phénomène dynamique et caractériser au mieux le champ de contraintes dans les futurs panneaux exploités afin de détecter d’éventuelles autres zones à risque. Cet article présente une synthèse des résultats obtenus, et discute ces résultats en liaison avec le contexte d’exploitation, les résultats de modélisation numérique, de caractérisation en laboratoire et de surveillance microsismique. MOTS CLES: Mine, coup de terrain, contrainte, surcarottage, mesure.

Jan 1, 2003

By K. Saito, Y. Miyauchi, T. Nishi, Y. Kizu

At Tokushima Plant of Nippon Denko Co., Ltd. high-carbon ferromanganese is produced by the electric furnace method using lump manganese ores and sintered manganese ores manufactured from fine manganese ores. However, the distribution of manganese ores is significantly uneven on earth, and their characteristics considerably vary by ore type. It is known from experience that the production of high-carbon ferromanganese by the electric furnace method depends greatly on material ores. Therefore, to maintain stable operation in the electric furnace-smelting field, it is important to identify the characteristics of each type of material ores in advance. Thus, we evaluated the high-temperature electric characteristics of manganese ores using the electrical conductivity measuring system developed by ourselves and provided the standards for determining ores and blending ratio necessary for stable operation of the electric furnace based on the evaluation results. This time we worked for optimisation of the high-temperature electric characteristics of sintered manganese ores through modification of the characteristics because the blending ratio of sintered manganese ores in the electric furnace is high. The electrical conductivity of sintered ores having various chemical components in a high-temperature region (up to 1 550°C) was measured using our electrical conductivity measuring system and high-temperature electric characteristics evaluating method reported at INFACON 9. As the result of the measurement, we revealed that the high-temperature electric characteristics of the sintered ores depend on their chemical contents and the sintered ores can be modified to those having excellent high-temperature electric characteristics by controlling their chemical contents, so that the resources can be effectively used.

Jan 1, 2004

By E. H. Myrhaug, K. Aasly, T. Malvik

Quartz is one of the main raw materials for the carbothermic production of ferrosilicon and silicon metal. The ideal process is written: SiO2 + 2C = Si + 2CO The real process is much more complicated, depending on the quality of the raw materials. Several research projects have been carried out on quartz for the (Fe)Si process during the last 50-60 years. One of the important properties that have been discussed in this review is the volume expansion that takes place between 850 °C to 1000 ºC and explosive disintegration for some quartz types. No final and definite conclusions have been made but several reasons have been mentioned: The influence of the phase transformation to tridymite, which takes place within the same temperature interval, has been discussed in several papers. Alkali impurities have been mentioned as a critical factor for this transformation to take place. Other researchers have mentioned mica impurities as a critical factor for the behavior of the quartz at these temperatures. Studies of fluid inclusions in quartz was reported in some papers focusing on the volume expansion of these during heating as a source of explosive disintegration, especially along planes of healed micro fractures that often contain vast numbers of such inclusions. Several methods for investigations of the important properties of quartz have been presented and these provide a good basis for the further research on quartz raw materials.

Jan 1, 2007

The paper examines the design issues associated with the integration of mineral processing within underground mining systems. It demonstrates conceptual integrated system design options appropriate to a range of geological scenarios. Particular reference is then given to a case study of stoping in narrow base metal veins. The performance of such integrated systems in terms of productivity, economic and environmental criteria is demonstrated by means of simulation. Particular attention is given to the potential benefits to mine waste management. Processing technologies appear to offer genuine potential benefit, whilst underground mining methods may need to evolve further to facilitate full integration. This paper is based on industry supported research aimed at developing selective and clean underground mining systems.

Jan 1, 2003

By W. de Beer

We present aspects of one of several ongoing case studies used in the development of prediction techniques for major seismic instabilities. The current investigation centres on accelerated coseismic deformation described by the kinematics of failure and on softening, as well as the characterization of areas of interest by measures of the seismic response at such sites.

Jan 1, 1998

By W. Banda

Paper written on project work carried out in partial fulfilment of Phd. (Process Engineering) degree* The recovery of cobalt and copper from waste slag was studied in a plasma DC-arc furnace in reducing conditions. Three fluxes, CaO,CaF2, and TiO2, were investigated for their influence on selective recovery of cobalt into an iron-rich alloy. A further investigation on the influence of furnace power on the reduction of slag to recover cobalt to the alloy showed that a change in power setting had an unexpected effect on the recovery of metals to the alloy, in that selectivity of base metal recovery over iron recovery decreased at an increased power level. Keywords: DC-furnace, reduction, nonferrous, slags

Jan 1, 2004

By B. S. Xakalashe

Keywords: Pyrometallurgy, silicon, solar cells Silicon has been the dominant material in the photovoltaic (PV) industry since its application in the space industry in 1958. This review focuses on crystalline silicon solar cells, primarily due to their dominance in the photovoltaic industry, omitting other photovoltaic cell technologies such as second generation (e.g. thin films) and third generation (e.g. nano-structured solar cells). The value chain for the production of crystalline silicon solar cells has been reviewed. The primary processing steps for the production of silicon solar cells from quartz are as follows: bulk production of metallurgical-grade silicon via carbothermic reduction in a submerged furnace, refining of metallurgical-grade silicon via the chemical means to polycrystalline silicon, or through the metallurgical route to solar-grade silicon, wafer manufacturing, and, lastly, silicon solar cell manufacturing. During downstream processing, solar cells are interconnected and encapsulated into solar modules (panels), which can be used individually or incorporated into a photovoltaic system for electricity generation and supply. The cost for crystalline silicon based solar cells is approaching one US dollar per watt peak ($1/Wp), while the most cost-effective solar modules in industry have reported costs below $1/Wp, and are based on CdTe thin films. Solar cell energy conversion efficiencies as high as 22% have been reported in industry for crystalline silicon solar cells.

Jan 1, 2011

By M. J. Papo, A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2 wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5 wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate while increasing it decreased the corrosion rate. KEYWORDS Austenitic stainless steel, %ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentiodynamic scans, microstructure, chemical analysis.

Jan 1, 2006

The key aspects of process metallurgy that distinguish platinum group metal (PGM) concentrate smelting from that of other base metal sulphide concentrates are presented. These differences include considerably higher input chrome and magnesia contents that directly raise the slag liquidus temperature and have the potential to increase accumulations of refractory spinels. Most importantly, the higher processing temperature required for PGM smelting and the resulting very high matte superheat lead to considerably more onerous smelting conditions than those typical of other smelting operations. This has presented challenges to furnace design and integrity, especially when coupled with the progressive intensification of smelting, involving doubling, and then redoubling, of furnace power inputs over the past 20 years. These power increases have been enabled by increasingly more advanced furnace cooling and structural technologies. Key technologies include strong constant-force spring-loaded bindings acting in three dimensions to minimize infiltration of superheated matte into brick joints, and robust well-cooled tapholes for reliably tapping the superheated matte. The result has been substantially improved productivity, and reduced smelting capital cost outlay per unit of production. A significant challenge, which was not anticipated, presented itself in the form of insidious corrosion of the furnace lining, and especially high-intensity copper cooling elements. Investigation of corrosion in related industries eventually identified chloride-accelerated sulphidation', and this term has been retained as it generically describes the most pertinent aspects of the accelerated low-temperature wear of copper coolers observed in PGM smelting. In addition to discussing the corrosion mechanism, this paper describes a number of solutions that were developed jointly by Anglo American Platinum and Hatch to address the copper corrosion problem. First, new monitoring technologies allowed furnaces to be operated more safely for a longer period of time. Second, a system for replacing corroded coolers from outside the furnace during a fast 'hot' shutdown minimized the impact on furnace operating factor and hearth life. Finally, a corrosion-resistant graphite-protected cooler design significantly improved furnace campaign life, and heralds a more lasting solution to cooler corrosion in PGM furnaces.

Jan 1, 2013

By B. Leong, H. Joubert

Keywords: Pyrometallurgy, furnace, auxiliary equipment, copper slag launders Pyromet has designed copper launders for tapping slag. What makes Pyromet?s launder design innovative and safe is that it does not have any cooling water channels underneath the launder runner, whilst achieving effective cooling of the runner. If matte burn-throughs were to occur through the launder runner, the risk of damaging water channels and the risk of explosions are reduced. In addition, since the cooling water channels are not harmed, the launder is easily repairable and reusable. Pyromet makes use of Finite Element Analysis to optimize the launder geometry to ensure that sufficient energy is removed from the centre of the launder. Factors considered during the launder design include the suitability of the geometry to the client?s needs, experience from existing installations, and ease of fabrication. Pyromet goes so far as to develop procedures for fabricators to ensure that fabrication issues do not compromise the functionality of the launder. When launder orders are received by Pyromet, the entire fabrication process and the functioning of the launders during operations are monitored to ensure that the launder designs are continuously improving with every installation.

Jan 1, 2006

By H. Appiah

Small scale mining (SSM) has been going on for a long time in Ghana. SSM was legalized by the PNDC Law 218, 1989. Since then there have been numerous gains from the SSM industry. The SSM is organized locally by the concession owner who engages people to work for the gold which he buys. Small scale miners (SSMs) use crudely made sluices in Ghana and, therefore, their production falls below what is expected. The SSMs work in groups and not as cooperatives, as they do in Brazil and other Latin American countries. Legalization of SSM has curbed gold smuggling considerably because a gold marketing entity is available. SSM poses certain environmental problems like pollution of water bodies and soils by mercury and indiscriminate digging of pits.

Jan 1, 1998

Keywords: Pyrometallurgy, furnace, Lonmin, platinum, PGM, UG2 Lonmin, earlier than any other primary platinum producer, had to deal with the concentrating and smelting of UG2-rich ores and concentrates respectively. Smelting was performed at a fairly modest scale compared to its industry peers in the Platinum Group Metals (PGMs) industry, and was focused on smelting concentrates obtained through low mass pulls while still maintaining high recoveries at its concentrators. Lonmin gradually smelted larger quantities of UG2 concentrates. Initially two 2.3 MW Infurnco furnaces were commissioned in 1982, followed by three 5 MW circular 3-electrode Pyromet furnaces in 1991. Deep electrode immersions and moderately high hearth power densities were used in all the designs. Lonmin decided to continue with circular furnace technology when it planned its new high-intensity No. 1 Furnace. Neither Lonmin nor the technology supplier and EPCM company foresaw the challenges that scale-up would bring when applied to the smelting of UG2-rich concentrate blends. Superimposed on the high chromite content, was the low base-metal loading, mineralogical difficulties, and fine particle size that came with milling of all concentrates (especially UG2 and recycle materials within the smelter). Through a process of fundamental diagnoses of furnace run-outs and wear patterns observed during repairs, the main challenges operating this high-intensity furnace were identified as sulphur vapour corrosion of the copper coolers, uneven and unpredicted movements of refractory bricks with associated copper cooler lift and matte tap-block movement, the formation of three-phase ?mushy? zones, high refractory and tap-hole wear rates, uncertainty in matte level and associated insufficient matte buffer height, and high furnace operating temperatures. These factors seldom worked in isolation and will be explored in more detail in the paper. The variability in furnace feed characteristics led Lonmin to re-design Furnace No. 1, to invest in back-up furnace capacity, and to invest in improved monitoring and control. These improvements consisted of online and high-frequency off-line feed chemistry and mineralogy monitoring, online pressure monitoring of water-cooled circuits, an alternative matte liquid level measurement in the furnace, and electrode immersion estimation. Improvements were also made at the converters by installing and utilising optical spectral analysis of the converter flame to characterise converter behaviour and achieve the desired iron end-point for white matte. This paper also briefly discusses the current and future expansion plans, as well as ancillary operations at the smelter such as flue-gas handling and materials handling.

Jan 1, 2011

By Ian MacKenzie

Over the past twelve years, professionals such as architects, engineers, accountants, and attorneys have not had to pay a great deal of attention to GST. The fees charged to clients (outputs) have not been subject to GST, but they have had to pay GST on al purchases of materials and taxable services relating to their activities.

Jan 1, 1990

By R. Katzenbach, M. Vogler, U. Adamietz

Abstract The design of deep excavation pits in rock mass is dependent as well on the mechanical properties of the rock mass as for example the orientation and the type of discontinuities like bedding planes, joints and fissures, the length of the discontinuities (persistence), the grade of weathering, the strength of rock mass, and the shear strength in the discontinuities, etc., and also on the respective boundary conditions specific for the project, and here especially the geometrical boundary conditions. The basic mutual influences and interactions between these boundary conditions are explained and exemplary presented at an excavation pit with a depth of 18,5 m, situated at a slope with a surface near groundwater table. Résumé La planification des excavations profondes dépend aussi bien de la qualité mécanique du roc, par exemple la location de la texture de la surface de moindre résistance, le degré de rupture, le degré de décomposition, la dureté du roc et la résistance limitée au cisaillement de la texture de la surface de moindre résistance que des conditions limitées spécifiques pour le projet, ici en particulier des conditions limitées géométriques. Les influences et interactions essentielles et mutuelles entre les conditions limitées isolées seront expliquées et présentées à l’aide d’une excavation 18,5 m de profondeur, située sur une pente où le niveau des eaux souterraines est près de la surface. Kurzfassung Die Planung tiefer Baugruben im Fels hängt sowohl von den mechanischen Eigenschaften des Fels wie z.B. der räumlichen Lage des Trennflächengefüges, dem Durchtrennungsgrad, dem Verwitterungsgrad, der Gesteinsfestigkeit sowie der Scherfestigkeit des Trennflächengefüges als auch von den projektspezifischen Randbedingungen hier insbesondere von den geometrischen Randbedingungen ab. Die wesentlichen gegenseitigen Einflüsse und Interaktionen zwischen den einzelnen Randbedingungen werden aufgezeigt und an einer 18,5 m tiefen Baugrube in Hanglage mit oberflächennahem Grundwasser vorgestellt.

Jan 1, 2003