Search Documents

By R. L. Setsepu, S. O. Bada, J. Abdulsalam

The utilization of biomass as a solid fuel for co-firing has received great attention from boiler manufacturers as a clean coal technology (CCT) option. This research aimed to produce biocoal pellets, as a clean energy fuel, using hydrochar from trees planted to rehabilitate acid mine drainage (AMD) water and fine coal discards. The hydrochar was synthesized by hydrothermal carbonization of Searsia lancea harvested from AMD-contaminated land at a temperature of 280°C and a residence time of 90 minutes. It was blended with discard coal (–1 mm) at ratios of 25% and 50% hydrochar to produce different forms of solid pelletized biocoal (BC). The physicochemical and mechanical properties of each of the biocoal pellet blends were determined. The 100% hydrochar had the highest calorific value of 29.99 MJ/kg, while the raw discard coal had a calorific value of 16.73 MJ/kg. The ash content decreased from 42% in the discard coal to 25% in the blend of 50% coal and 50% hydrochar biocoal pellets. Biocoal pellets comprising 25% hydrochar and 75% discard coal (BC25 HC/75 COAL) displayed the best mechanical properties (compressive strength 3.06 MPa) of all the fuels, but the physicochemical properties were inferior to the BC50 HC/50 COAL pellets. This research has demonstrated that hydrochar synthesized from a tree species planted for hydraulic control of AMD has the capability to act as a binder for improving the mechanical properties and energy characteristics of fine discard coal.

Dec 1, 2021

By G. Mahieu, L. Perez-Barnuevo, P. Barbeau-Verreault, O. Gravel

Raglan mine is a copper-nickel mining operation, part of Glencore, and located at the northern border of the province of Quebec, in Canada. The concentrator is fed by a mix of four different underground mines, thus it must accommodate periodic variations in run-of-mine mineralisation and composition. In order to concentrate nickel and copper sulphides, the flotation circuit also includes a regrind step at the cleaner stage. This leads to challenges in maintaining optimal recoveries and in diagnosing potential disturbances. This paper advocates for the combination of automated mineralogical analyses, reconciliated mass balances from diagnostic sampling campaigns and innovative multidimensional visualisation to assist in tackling these challenges. Through this approach, it has been possible to quantify the regrind step influence on the liberation of valuable mineral particles in the final flotation concentrate. The methodology also allows for virtual sieving of the products in order to track unit loss in the flotation process. The proposed analysis scheme presents an opportunity to easily diagnose flotation circuit performance based on mineralogical information. Keywords: Flotation diagnostics, multi-dimensional visualisation, mineral liberation analysis

Jan 1, 2020

By K. Wu, X. Yuan, R. Du, C. Chao

"Lump coals are currently employed to replace part of coke in the COREX melter-gasifier for ironmaking. In order to optimize the process, the pyrolysis kinetics of Datong coal used in the COREX process was studied. A sectioning method is proposed to overcome certain shortcomings of traditional methods for studying the pyrolysis of coal. Based on the sectioning method and the characteristics of the coal pyrolysis process, the temperature range was divided into three intervals. In the first, the adsorbed gas and water of crystallization were removed; in the second, the coal was transformed into semi-coke; and finally, the semi-coke was further coked. Three models of reaction were then established to study the different stages of the pyrolysis process: an interfacial chemical reaction model, a random pore model, and internal diffusion with shrinking volume. The results showed that the experimental data fitted the models well, with all correlation coefficients (r2) exceeding 0.97. Finally, the mechanisms of reaction and kinetic parameters for each temperature range were derived, which laid a necessary foundation for optimizing the usage of non-coking coal in the COREX process. IntroductionIn view of environmental concerns and the shortage of good-quality coking coal, the COREX process was designed as a new ironmaking technology, attracting wide attention (Fang et al., 2005). In this process, lump coal and a small quantity of coke are directly charged into the melter-gasifier, where a high-quality reducing gas is generated for the reduction of the iron ore (Kumar et al., 2009). In contrast to the conventional blast furnace (BF) process, non-coking lump coal is used as the reducing agent and as the energy source, and the iron charge consists of lump ore and/or pellets, which results in the elimination of the coke oven and sintering plant as well as a decrease in investment (Kumar et al., 2009; Liu et al., 2012).Although the COREX process has made great progress, in current production practice the energy consumption greatly exceeds that of the BF, and it requires a certain amount of coke to maintain permeability of the semi-coke bed (Wang et al., 2008). In addition, the process consumes a lot of good-quality lump ore and lump coal. The pyrolysis of coal is the first step in most coal conversion processes, such as carbonization, gasification, and combustion (Aboyade et al., 2013). The reaction behaviour of lump coals in the COREX melter-gasifier is crucial, as it determines energy utilization and gas composition, as well as the metallurgical properties and particle size of the semi-coke produced (Prachethan et al., 2011; Zhang et al., 2014). In order to optimize the process and improve its competitiveness, the pyrolysis kinetics of Datong coal used in Baosteel’s COREX C-3000 facility was studied."

Jan 1, 2016

By D. A. Hayman, N. Rambuda, N. A. Sithole, C. Hockaday, J. D. Steenkamp

"Mogale Alloys operates two alternating current (AC) submerged arc furnaces (SAFs), and two direct current (DC) open bath furnaces. These furnaces are capable of producing two products, silicomanganese (SiMn) and ferrochrome (FeCr), with a total production capacity of 110 000 t/a. This paper focuses on the silicomanganese process specific to Mogale Alloys, with a two-furnace operation facility that produces 55 000 t of SiMn per annum.IntroductionMogale Alloys is situated in Krugersdorp in the West Rand District Municipality in South Africa’s Gauteng Province. The Krugersdorp facilities were initiated by Palmiet Chrome Corporation in February 1963 to produce charge chrome (Basson, Curr, and Gericke, 2007). Mogale Alloys bought the Palmiet Chrome facilities in 2005 from Samancor Chrome. The Afarak Group currently owns 90% of Mogale Alloys.SiMn is produced in two 20 MVA submerged arc furnaces (SAFs), which were originally built for chromite processing, and ferrochromium (FeCr) in two DC open bath furnaces rated at 40 MVA and 10 MVA. When this paper was compiled, the 10 MVA furnace was not operational due to the high cost of production, and one of the 20 MVA SAFs was recently converted to produce FeCr due to market constraints. Mogale Alloys has 290 permanent employees with four contracting companies on site. The paper presented here focuses on the production of SiMn at Mogale Alloys.The high-level process flow at Mogale Alloys is summarized in Figure 1, which details the raw material input and the products produced by the two 20 MVA furnaces. SiMn is produced by carbothermic reduction of manganese-bearing raw materials from four different sources, namely Wessels, Mamatwan, and UMK ores, and BHP sinter feed. The carbon sources are bituminous coal from Forzando and Msobo, local suppliers in Mpumalanga."

Nov 1, 2018

By B. M. V. Baloyi, D. Mchabe, D. Chetty

South Africa accounts for the largest global manganese ore production share, primarily from its Kalahari Manganese Field deposit. Despite this, domestic smelting is beset by energy constraints, resulting in most ore being exported for smelting. Mintek is investigating energyefficient pathways for ore reduction, specifically undertaking prereduction tests to reduce energy consumption for manganese smelting. The present contribution considers the effect of methane, anthracite, and holding time, at a fixed temperature, on the extent of reduction of Mamatwan-type ore, primarily from a mineralogical perspective. In particular, the aim was to carburise the monoxide Mn phase to Mn carbide, as this is less energy intensive than producing metallic Mn from the monoxide. Based on thermogravimetric test results, the ore and products from three experiment sets were analysed using X-ray diffraction and scanning electron microscopy to assess the phases and textures present. The findings show that carburisation of manganese monoxide and its equivalents is most advanced under conditions of 8% anthracite, 10% methane, and 60 minutes of holding time, thus confirming with the thermogravimetric data. These results show promise for reducing energy consumption for Mn smelting in ferromanganese production.

Mar 4, 2025

By M. Rudolph, A. van Hall, G. Öktem, S. G. Özkan, A. Hassanzadeh

Despite the four-decade study on ultrasound’s (US) impact on mineral’s floatabilities, there is still not clarity regarding its role in mineral surface wettability. For this purpose, the present investigation endeavours ……the hydrophobicity and floatability characteristics of a chalcopyrite-pyrite-quartz (Cp- Py-Qtz) system in the presence and absence of an ultrasonic pre-treatment. The ultrasonic process was carried out by a sonopuls at a constant frequency of 20 kHz with an adjustable power level from 30 to 200 W. Initially, the impact of sonication time (15, 30, 45, 60 and 90 s as well as 10, 20 and 30 min) and power magnitude (30, 60, 90, 120 and 180 W) were evaluated while the dissolved oxygen, temperature, conductivity and pH were also monitored. Collector-less micro-flotation tests were carried out on the non-pre-treated and the US pre-treated samples at 60 W and 15 s. The samples’ hydrophobicities were determined by the drop shape analysis approach. The dissolved-oxygen level was varied using a mini bench pressurised water reactor to study the effect of O2(aq) concentration on the chalcopyrite and pyrite wettability characteristics. The results showed that the minerals’ hydrophilicities were relatively more sensitive to the sonication’s time than its power that resulted in reducing all three minerals’ hydrophobicities. In addition, it was found that the dissolved-oxygen content and creation of sub-micron sized bubbles led to an improvement on chalcopyrite and pyrite hydrophobicities. Finally, we proved that the Cp’s floatability increased and Qtz’s recovery reduced while being subjected to the ultrasonic irradiation (15 s at 60 W); however, Py’s recovery remained constant. This conclusion confirmed the possibility of a selective separation in ultrasound-assisted copper ore flotation. We recommend that further advanced investigations be conducted, using an X-ray photoelectron spectroscopy (XPS) and atomic force microscopy (AFM) to thoroughly understand the surface modifications induced by the ultrasonication

Jan 1, 2020

By Y. Qin, X. Fu, T. Qi, H. Tang

"The FASTMELT ® process was developed as an alternative to blast furnace ironmaking; in this process, high-quality molten iron is produced using direct reduction followed by high-temperature slag/metal separation. In this study, iron recovery and phosphorus removal from oolitic highphosphorus haematite using the FASTMELT® process was investigated. The performance of two reducing agents, coal and wood char, was compared. Direct reduction experiments indicated that with optimized reductant addition, the ore-char and ore-coal briquettes attained metallization values of 82% and 78%, respectively, and residual carbon contents of 0.24 and 2.35%, respectively. The slag/metal separation experiments revealed that molten iron containing 0.41% phosphorus and 0.021% silicon (by mass) was produced from optimally reduced ore-char briquettes, and molten iron containing 0.78% phosphorus and 0.91% silicon from optimally reduced ore–coal briquettes. The study indicates that carbonaceous materials with high CO2 reactivity are suitable for use in the FASTMELT ® process for phosphorus removal and iron recovery from oolitic high-phosphorus haematite. IntroductionIn China, the general depletion of iron-rich mineral reserves has led to many efforts to exploit low-grade and refractory ironcontaining resources for ironmaking (Liu et al., 2014). The efficient utilization of the highphosphorus oolitic haematite resources in central China has received considerable attention. The available resources of this material total approximately 3.0 billion tons. The oolitic units in the ore exhibit an onionlike structure with phosphorus-containing gangue layers of 2–10 µm thickness. The best concentrate produced from these resources contains approximately 50% iron (Fe) and 0.8–1.2% phosphorus (P) (by mass) (Ai, Yu, and Wei, 2009; Song et al., 2013; Wu, Wen, and Cen, 2011). Further removal of phosphorus from these ores using conventional beneficiation methods is not possible."

Jan 1, 2017

By O. O. Ogunmodimu, D. K. Weatherley, M. S. Powell

Discrete element methods (DEM) have provided the ability to resolve the complex phenomena experienced by ore within comminution devices such as tumbling mills. The new developments in DEM techniques and the corresponding increase in computational power have made it more feasible to study the movement of individual ore particles as they traverse a tumbling mill. A range of information can be extracted on individual particle impact histories, such as kinetic energy at the time of collision, velocities of individual particles, per-particle stress tensors, impulse, and collision energy. DEM codes have been modified to provide required information that can be analysed in associated software to investigate the impact of varied operational parameters on the resultant granular dynamics. This paper explores the reaction of individual ore particles to the breakage environment within a tumbling mill using DEM techniques and studies the stressing conditions that would lead to either impact or abrasive breakage. Keywords: DEM, comminution, tumbling mill, breakage

Jan 1, 2020

By X. Cao, R. Wang, H. Han, Y. Hu, Z. Wei, W. Sun, H. Tang, J. Wang

Flotation reagents play a vital role in mineral flotation. In the past century, most studies focused on the modification of anion or cation collectors and the synergistic effect of mixed collectors, which have contributed to research. In this study, we reviewed brand-new reagents, metal-organic/inorganic complexes, with the functional group of metal ion, which are totally different from the traditional anion or cation collector and show absolute specificity for some minerals. For example, Pb-BHA complex collector was developed to realise the atmospheric flotation of scheelite due to the absolute specificity for calcium minerals. Calcium oleate collector was found to be the effective species in the flotation of calcium minerals, and has been employed to selectively separate fluorite from calcite. Selective adsorption of Al-Na2SiO3 polymer on calcite surfaces proved the self-assembly of H2SiO3 polymer using Al3+ had stronger selectively adsorption ability than Na2SiO3. Also that Fe3+-starch complex was a better depressant for iron minerals than caustic starch and contributed to a more efficient reverse flotation. In conclusion, metal ions are good templates for molecular assembly and can be used to control the structure of metal complexes and exhibit special properties, which provide possibilities for the design of new flotation agents. Keywords: Metal-organic/inorganic; flotation; collector; depressant

Jan 1, 2020

By M. A. El-Sayed

"Double oxide films (bifilms) are significant defects in light alloy castings that occur when, during melt handling, the oxidized surface of the melt is folded over onto itself and then entrained into the liquid metal, encapsulating a portion of the local atmosphere. These defects create crevices in the final castings and have been shown to decrease tensile and fatigue properties, and also to increase their scatter, making casting properties unreproducible and unreliable. This paper reports on two different experiments performed to study the behaviour of such defects in Al alloys. In the first experiment and as a proxy for a bifilm, air bubbles were held in an Al-5Mg alloy melt for varying periods of time before the melt was allowed to solidify. The composition of the gas content of the bubbles was subsequently analysed using mass spectrometry to ascertain how it changed with time. In the other experiment the influence of the age of bifilms on the mechanical properties of Al-5Mg castings was assessed by holding castings in the liquid state for different times before solidification, followed by mechanical property testing and SEM and EDX studies of the fracture surfaces of tensile test bars. This research could provide a better understanding of the behaviour of double oxide film defects, and may lead to the development of new techniques by which these defects could be eliminated, or at least deactivated, in light alloy castings. Introduction One of the major structural defects affecting the reproducibility of mechanical properties of aluminium castings is the double oxide film defect (El-Sayed and Essa, 2017; El-Sayed and Ghazy, 2017). This type of defect is usually created as a result of poor filling system design. Owing to the very high reactivity of liquid Al-Mg alloy with oxygen in the air, the surface of the liquid metal can be considered to be permanently coated with an oxide film (Weigel and Fromm, 1990). As a consequence of surface turbulence, the oxidized metal surface can become folded over onto itself, but not fused, and then submerged into the bulk liquid, with a portion of the mould atmosphere being entrapped within it (Campbell, 2003; Al- Sayed, 2016; El-Sayed, Hassanin, and Essa, 2016)."

Nov 1, 2018

By J. E. Dickinson, R. Campbell, M. J. Cole, K. P. Galvin, M. C. Cole

It is common practice in the beneficiation of iron ore ultrafines to apply reverse flotation, and hence float the gangue minerals, leaving behind a high-grade iron ore product. Given the difficulty in floating particles finer than 20 μm, especially those finer than 10 μm, it is necessary to subject the feed to desliming ahead of flotation. There are two problems with this approach. Firstly, given the known inefficiencies of cyclones, desliming needs to be aggressively applied to particle sizes upwards of 45 μm to ensure all the offending ultrafine gangue is removed. Secondly, desliming also removes a significant portion of the valuable iron ore. Thus, a significant portion of the ultrafines, including the iron ore, is lost to the tailings. This paper examines the direct flotation of iron ore fines using the Reflux Flotation Cell. The RFC operates using a concentrated bubbly zone, in the absence of a conventional froth zone, for delivering strong counter current washing through an inverted fluidised bed of bubbles ahead of the product discharge. A system of parallel inclined channels in the lower part of the cell provides enhanced segregation of the bubbles from the tailings, preventing the loss of air bubbles into the tailings. Experiments conducted under semi-batch conditions produced encouraging results with concentrates of ~65% Fe grade in a single flotation stage. Comparatively, up to five successive batch flotation stages were required when using a laboratory scale batch mechanical flotation cell to achieve similar Fe grades. For a given grade, lower Fe recoveries were typically achieved by the RFC. This was attributed to the effective prevention of ultrafine particles succumbing to hydraulic entrainment under a positive bias flux, as well as an increasing feed volume involved in the semi-batch operation using inverted fluidisation water for cleaning. Overall, similar grade-recovery curves were produced, however, significantly higher grades were obtained by the RFC and with fewer separation stages. Keywords: Desliming flotation, iron ore, modified release analysis, reflux flotation cell

Jan 1, 2020

By M. E. Rossi, C. Badenhorst

Conditional bias occurs when the expected value of the true grade conditional on the estimated grade is not equal to the estimated grade. It is a quantification of how the average of estimates differs from the true value. Conditional bias is present in all resource estimates due to the unavoidable properties of kriging, and indeed all linear estimation (regression) methods. In a mining resource estimation context, the degree of conditional bias is dependent on the spacing of the conditioning data; more data leads to the expectation of less conditional bias This paper discusses conditional bias from two perspectives: 1. 2. Estimates seeking to eliminate, as much as possible, conditional bias; and Estimates that accept a larger amount of conditional bias in resource models, in order to achieve a specific outcome. The problem of conditional bias in estimation can only be fully appreciated if the objective or purpose of a resource model is understood. There are instances where conditional bias should be avoided because it is not reasonable to make decisions using estimates that are known to be wrong in expected value; for example, when making a final decision in grade control with respect to the destination of the material. In most instances in the mining resource estimation context, however, the estimated values will not be “final estimates”, but “interim estimates”, meaning that in the future more data will be obtained, and the ”interim estimate” will then be updated. In this context, the most useful resource model is an interim model that is able to predict the final model estimates, despite not having all the data available that will be collected in the future. This is the objective, for example, of a recoverable “long-term” model developed prior to operating a mine, for example at the feasibility stage. It attempts to predict the ore that a processing plant will receive, well into the future. In such cases, it can be unequivocally demonstrated that conditional bias is not only unavoidable, it is a necessity.

Sep 1, 2021

By G. van Aswegen

The geometry and morphology of a set of low-angle fractures around a stope in a deep Witwatersrand gold mine are explained in terms of extension fractures forming under variable conditions of stress. Primary extension fractures (E1) form some distance ahead of an advancing stope along the s1, s2 plane. With stope advance, a couple of these fractures end up in a stress regime conducive to transpressional shear and a secondary set of extension fractures(E2) is formed at a high angle to the primary fractures. i.e. at a low angle to the stope. As the E2 fractures are undermined, they migrate into a stress regime of transtensional shear and a third set of extension fractures (E3) may develop between E2 fractures. These have sigmoidal shapes, being parallel to the E2 fractures at the E2 discontinuity where s3 is negative, and curved through the unfractured rock between E2 fractures where s3 is positive at the instant of fracturing. The fractures all display fractographic features characteristic of dynamic extension failure with striae indicative of the direction of rupture propagation and the local, instantaneous orientation of s1.

Jan 1, 2012

By G. de Tomi, G. C. Teodoro, E. Rodovalho, T. M. El Hajj, J. A. S. Tenório

The selection of an underground mining method stems from a multivariate analysis that considers geomechanical, geological, economic, and operational parameters. Even after identifying the most compatible method, there is no assurance that the mining company will achieve the best performance. The geological complexity of some deposits requires adaptations of methods described in the literature to obtain more selectivity and reduce mining waste. There are some studies on geometry of underground structures, but a methodology that describes an adaptation of a room-and-pillar mining method for ore bodies with down-dip varying from 20° to 25° is novel. The present work aimed to reduce dilution by adapting the traditional room-and-pillar mining method (TRP) to inclined ore bodies. This new method is entitled short-hole room-and-pillar (SHRP). The equations that measure the dilution are defined according to the geometry of stopes and openings. The results comprise comparative analyses of the operational and planned dilutions to measure the performance of the SHRP method. The average operating dilution of the SHRP method was more than five times lower than the planned dilution according to the TRP method. Low operational dilution indicates high selectivity of the method and its potential to reduce underground mining tailings.

Sep 9, 2024

By N. Duda, P. Śliwiński, P. Stefaniak, B. Jachnik

Ventilation and air-conditioning are some of the most energy-consuming processes in deep underground mining. Additionally, the energy consumption of these processes systematically increases along with the expansion of the mine. Therefore, proper energy efficiency assessment and consumption forecasts of these systems are particularly important in modern mines for ongoing tracking and planning of the likely costs. In the article, a short-term prediction model for surface air–conditioning stations is described. This model takes into account dependencies that were identified, based on the data from the supervisory control and data acquisition (SCADA) systems. These dependencies between the response value and the external conditions are then incorporated into the model. This way, for example, the ambient temperature or the total number of specific days of the week (with sometimes significantly lower or higher than the weekly average energy consumption levels) are included. Taking into account these dependencies, and e.g. forecasted average monthly temperatures allow us to include the seasonality of energy consumption in the presented model. In the article, a sample energy efficiency analysis of the A/C system based on an example of the KGHM Polish Copper Polkowice-Sieroszowice mine is performed. The results of the solution proposed in the article are then evaluated, and compared to the currently functioning, more basic forecasting methods. However, given the general nature of the dependencies used in the model, similar solutions could be used in other case studies.

Sep 1, 2021

By M. S. Shishvan, J. Sattarvand, R. S. H. Meij

Navigating miners during an evacuation using a smart evacuation technology can significantly decrease the evacuation time of an underground mine in case of an emergency. This paper presents a mathematical programming model to calculate the most efficient escape path for each miner as a critical component of the smart evacuation technology. In this model, the total evacuation distance of the crew is minimised and scenarios with blocked pathways, and stamina categories for the miners are simulated. It was found that all the tested scenarios are technically feasible. Using the feature that filters out blocked pathways has no downsides, as safer routes are calculated, and there is no penalty in the computation time. The paper also discusses the social and technical issues that need to be overcome before the algorithm can be implemented as an actual escape solution.

Sep 1, 2021

By F. D. Agrensa, J. Hadjigeorgiou, E. Storimans, S. J. Thorpe

Reinforcement and surface support are part of an integrated system that transfers and shares loaduntil the excavation surface is stabilized or until the ground support system fails. Steel mesh is the most popular primary surface support element in underground hard rock mines in Canada. Mesh straps are a secondary surface support that provide additional containment as they distribute the load between and across the reinforcement elements. This investigation addresses the role of steel properties, and in particular steel chemistry, in the long-term performance of mesh and mesh straps when exposed to an aggressive corrosive environment. It reports on comparative accelerated corrosion studies to compare the resistance to corrosion of different surface support elements. This has significant implications on the choice of surface support and the anticipated rehabilitation requirements.

Oct 9, 2024

By R. W. O. Kersten

"The aim was to investigate stable pillar design procedures currently in use on chrome and platinum mines, subject them to a critical appraisal, and review some of the alternatives proposed in the literature. It is concluded that these pillar design methodologies suffer from drawbacks that can be detrimental to the mining industry and that an improvement is essential.It was decided that the increased availability of analytical models and failure criteria could be exploited to update the empirical to an analytical/empirical method. The proposed methodology adopted FLAC2D simulations using the Hoek-Brown failure criterion to calculate full stress-deformation curves for typical pillars. The mine stiffness concept was introduced to determine the pillar load, integrating the influence of the pillar and strata stiffness and mining geometry.The proposed methodology was calibrated by comparing experimental and predicted deformations and failure depth of pillars in one hard-rock mine. The conclusion was that the methodology is an improvement over the one currently in use. An improved factor of safety is given by the intersection point of curves for the stiffness of the system and the pillar strength. IntroductionThe paper describes part of the findings of a PhD thesis (Kersten, 2016) on an alternative stable pillar design methodology. This publication contains sufficient information to implement the method for further interpretation and testing. A detailed comparison of measured and predicted data is dealt with in the thesis, and the results show that there is promise in the methodology.The design of stable pillars in mining is of fundamental importance, not only in the Bushveld Complex mines but throughout the mining industry. Wherever mining occurs, pillars are formed at some stage and it is essential to predict their behaviour, i.e. whether they will burst, yield, or remain stable. Although of crucial importance, pillar design still suffers from major shortcomings and weaknesses."

May 1, 2019

By K. Moxham, A. Smit, R. Pickering

Since the early 1970s research has been ongoing to develop a cost-effective way of continuously mining the narrow reef, hard rock, typical of South African gold and platinum mines. In the late1980s it was shown that impact ripping was a practical solution for the deep gold mines. In March2001 Lonmin and Sandvik agreed to co-operate in an endeavour to design and manufacture a prototype narrow reef mining machine with the ultimate aim of producing such a machine on a commercial basis that would enable Lonmin to create a safer and more productive environment within its mines and for Sandvik to enhance its leading position as a supplier of a new generation hard rock cutting machine. This paper describes the developed technology, the current progress of the delivery of the required objectives and the optimum mining layout for the roll-out of the mining method.

Jan 1, 2006

By K. E. H. K. Ishak, S. R. M. Zan

Cement production requires significant energy, and entails high costs and CO2 emissions. This is because the clinker requires very fine grinding. Grinding aids can improve production and fineness and decrease energy consumption by reducing the agglomeration of particles and protecting the balls and liners in the mill. In this study we compare the effects of three different grinding aids on clinker grinding using a ball mill. A commercial grinding additive, triethanolamine (TEA), and two industrial grinding aids (GAA079 and GAA088) were compared by ball milling tests, with additions of 0.05, 0.25, 0.50 and 1.00 wt%. The industrial grinding aids were characterized using gas chromatography-mass spectrometry (GC-MS). Particle size and morphological analyses were performed using SEM and XRD. The best results were obtained with 0.25% GAA088, which has a higher active component of diethanolamine isopropanolamine (DEIPA) than TEA. The unique combination of TEA and DEIPA in GAA088 enhances grinding efficiency and significantly improves the particle size distribution compared to TEA alone.. The grinding aids produced smooth rounded particles, which have a smaller specific surface area, enhancing the quality of the cement. XRD showed no significant structural distortion with or without grinding aids, and it was also found that the grinding aids helped decrease ball coating during grinding. The use of grinding aids can significantly improve clinker production and fineness while decreasing energy consumption, which can help reduce the costs and CO2 emissions associated with cement production.

Sep 6, 2023