Search Documents

Determine the minimum waterflow rate needed for effective control of dust produced by cutting machines used to mine water-soluble ores. Approach Conventional wet-bar cutting techniques were studied to evaluate their dust control performance, and the optimum water flow needed for dust suppression was determined. Wet-bar type cutting techniques are used to help control mine dust by keeping the cutting chain wet. As the chain cuts the kerf, it dampens the dust produced by the cutting action at the point of generation. The Bureau, under contract, evaluated three basic wet-bar techniques, as shown in the diagram: water-trickle system A uses a gravity-feed or low-pressure (less than 50 psi) pump to send water through the bar and to discharge it at the bar tip. Water-spray system B uses a low-pressure spray nozzle located at the front of the cutter head. For protection the nozzle can be located within the cutter

Jan 1, 1982

Develop a means for analyzing seismic crosshole data to predict and monitor the Flow of leach solution during in situ mining. Background Improvements in predicting and monitoring in situ leach solution flow would aid in planning well field configurations. These improvements would also facilitate permit application by assuring regulatory agencies that leach solution would not escape from a well field undetected. Seismic tomography can detect fractured zones, which enables the prediction of probable flow paths, and it is a promising technique for monitoring leach solution injected above the water table. Tomographic analysis of crosshole seismic data provides a two-dimensional picture of the distribution of seismic velocities between the transmitter and receiver boreholes. The positions of fractured zones and of leach solution can then be inferred from the seismic velocities.

Jan 1, 1989

By Philip W. Holland

The U.S. Bureau of Mines has developed an improved method for determining dissolved helium in water in the concentration range of 4.0 x 10-8 to 270 X 10-8 cm3 He (STP)/cm3 H2O. The method is a modification of a previously reported method that was developed for analrzing surface and subsurface waters in geochemical survey work. Water samples are collected in SOD-cm stainless steel cylinders, and the dissolved gases in a sample are extracted into an evacuated cylinder of equal volume. After addition of 30 psig of nitrogen containing less than 2 ppb helium to the extracted gases, the resulting mixture is analyzed for helium using a helium-tuned mass spectrometer. The helium content of the water sample is determined from an empirical calibration that is established by analyzing standard solutions of helium in water. The accuracy of the method is ±7 pct for helium-in-water concentrations above 10 x 10-8 cm3 He (STP)/cm3 H2O.

Jan 1, 1989

By C. E. Jordan

The Bureau of Mines conducted tests on seven samples of Florida phosphate operations.slimes to develop a method to recover phosphate presently being discarded because of its small grain size. A system of hydrocyclones and hydroseparators was used to recover up to 96 pct of the plus 400-mesh material from the slimes. This plus 400-mesh material was subjected to fatty acid flotation, and concentrates containing up to 33.4 pct P205 were produced. As much as 88 pct of the phosphate (P205) was recovered from the plus 400-mesh material, and up to 29.6 pct was recovered from the total slimes.

Jan 1, 1982

By R. L. Montgomery

Electronegativities of the rare-earth elements were calculated from heats of formation. The values obtained from different compounds varied widely. The postulates of Pauling's electronegativity theory were interpreted for bonds that are primarily ionic; the study showed that many compounds obey rules of the form expected. Revised electronegativity values are given for the more electropositive elements, including the rare-earth metals (which are near magnesium in electronegativity). Estimates of un-known heats of formation are made from electronegativities and are compared with other estimates. INTRODUCTION Calculation of the electronegativities of the rare-earth elements is interesting to show how these metals stand relative to the other metals and to each other, and also possibly to systematize the thermochemical data on them.

Jan 1, 1960

By A. R. Rule

Laboratory tests were conducted to study removal of magnesium impurities from western phosphate rock concentrates by selective leaching. The systems evaluated included leaching with dilute sulfuric acid, with ammonium sulfate, and in an aqueous medium with sulfur dioxide gas. Set standards for the magnesium impurity level of phosphate rock concentrates are not available, but industrial practice has indicated that magnesium in excess of 0.3 percent MgO causes problems in phosphoric acid manufacture. Removal of magnesium was accomplished with all three systems. With dilute H2S04 the magnesium level was reduced to less than 0.1 percent MgO with an accompanying P205 loss of 6 percent. Magnesium oxide levels from 0.3 to 0.2 percent were obtainable with ammonium sulfate. However, the system requires concentrate roasting at temperatures of 900° C or higher, heated pulps (100° C), and large quantities of ammonium sulfate. Selective leaching was obtained using S02 gas in an aqueous concentrate slurry. Magnesium oxide content was reduced to less than 0.1 percent without loss of phosphate.

Jan 1, 1970

By B. J. Scheiner

Carbonaceous gold-bearing ores of the type that occur in north-central and northeastern Nevada were investigated by the Bureau of Mines as part of its Heavy Metals Program. Specific objectives were to identify the carbon and organic compounds that prevent adequate gold recovery from the ore by cyanidation and to develop an economical process that would overcome the detrimental effect of the carbonaceous constituents. Activated carbon and long-chain organic compounds containing sulfur and nitrogen were found in the ore. Part of the material consisted of stable gold organic complexes. A mild oxidation technique that allowed gold extraction as high as 96 percent by subsequent cyanidation was developed. A variety of oxidants was shown to be effective in improving gold recovery, including chlorine and sodium hypochlorite (NaOC1). An electrolytic oxidation process was developed that was particularly advantageous from an economic and effectiveness standpoint.

Jan 1, 1971

By H. Carroll

An ozone detector was built and evaluated for its applicability in smog-chamber studies. The detection method is based on the reaction of ozone with ethylene and the measurement of resultant chemiluminescence. In the first phase of evaluation, the detector's response to ozone was studied as a function of several instrument parameters, and optimum conditions were defined for the maximum and most stable responses to ozone. In subsequent evaluations, the method was checked for sensitivity, precision, and interferences and was compared with two alternative methods. Results showed the chemiluminescence method to be acceptably sensitive and precise for smog-chamber studies and superior to the Mast ozone meter and KI (colorimetric 1 percent neutral-potassium iodide method) methods in that it is specific for ozone.

Jan 1, 1972

Develop personal computer (PC) based software for analyzing and/or filtering time- and frequency-domain attributes of seismic and electromagnetic signals from geophysical surveys for the enhanced interpretation of rock masses and subsurface geologic structure. The Problem Both mining and petroleum geophysicists utilize seismic signals to characterize rock masses for delineating subsurface stratigraphy and structural conditions. However, a vast amount of information available in seismic project evaluation data often is unavailable for interpretation unless these data are enhanced. New processing technology increases the quality of these signals for analysis and interpretation. Comprehensive signal processing software is mostly written for petroleum exploration companies. Commercially available signal processing programs are often limited to a single application or are restricted for use with specific hardware, e.g., a digital oscilloscope or a mainframe computer. The programs may use computer codes that are proprietary, restrict user modification to expand capabilities, or may be hard to interface. They may have insufficient documentation for easy use and be support dependent.

Jan 1, 1990

To prevent injury to miners caused by violent whipping of mining machine trailing cables. Approach: The hydraulic cable controls are adjusted to reduce whip by visual reference of the cable sag to the height of the cable guide. How It Works: The cable sag is adjusted by visually estimating its height above the ground, at a specific reference distance behind the machine. This reference distance is measured horizontally back from the point where the cable leaves the cable guide. The Reference distance is 2H where H equals the height of the cable guide above the floor. See Figure 1. Cable sag should be less during rewinding than during unwinding. During cable unwinding, the cable height (at the refer¬ence distance) should equal 1/31-1. During rewinding, the cable height should equal ½ H. Field tests were made on several manufacturers' equipment after adjusting cable sag as above. Cable whip was greatly reduced for all, and whip was almost eliminated on a shuttle car equipped with a Joy Manufacturing Company 500108-104 cable reef and the newer (nonporous) shuttle valve. The following directions are for adjusting cable sag on a shuttle car equipped with a Joy Manufacturing Company 500108-104 Cable Reel equipped with the newer shuttle valve. Cable sag can be adjusted on machines equipped with other cable reels and valves by referring to the manufacturer's manual and making the appropriate cable valve adjustments.

Jan 1, 1976

By Peter F. Strong, Robert L. Lagace, Alfred G. Exslie

The theoretical study of WF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a comer is the concern of this paper. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency that propagates with the smallest loss. The theoretical results are compared with published measurements. This work was part of an investigation of new ways to reach and extend two-way communications to the key individuals who are highly mobile within the sections and haulageways of coal mines.

Nov 14, 1974

By Ivette E. Torres

Bulk carriers, freighters, and tankers are the three classes of seagoing vessels engaged in transporting mineral commodities. However, vessels in these classes are not exclusively devoted to mineral commodity transport. Bulk carriers move considerable tonnages of agricultural products as well as crude minerals, their concentrates, mineral fertilizers, and the like. Freighters, owing to their great variety, can be devoted wholly to hauling mineral products or wholly to nonmineral goods, as well as carrying mixed mineral commodities and nonmineral commodities. They include general cargo ships, full container ships, partial container ships, roll-on/roll-offships, and barge carriers. Tankers, although largely engaged in moving crude oil and refinery products, also transport liquid chemicals, molasses, wine, liquefied natural gas, and other fluids. Although physical characteristics of vessels such as size, draft, crew requirements, type of propulsion system, ratio of gross tonnage to cargo tonnage, and fuel costs have undeniable influences on shipping industry performance, problems of and changes in the quantity and types of materials moved also significantly affect the shipping sector of the world economy, and thus have a bearing on the minerals sector of that aggregate. Unfortunately, comprehensive global data reflecting changes in these critical variables are not published.

Jan 1, 1994

Reduce the dust exposure to the operator of a longwall shearer with a novel foam spray system. Approach Discharge foam through the nozzles of a shearer drum so that foam and coal are better mixed. How It Works Bureau of Mines research showed that two very important principles for successful application of foam are: (1) moisture distribution and (2) degree of mixing. Foam can distribute a given quantity of moisture much more evenly over a large surface area. Successful Bureau tests of foam for dust control always involve a high degree of mixing between the foam and the material, Mixing, permits a greater distribution of foam throughout the mined product. The most suitable location of foam application would be at the point where the dust is generated, before the dust becomes airborne. Foam nozzles located in the cutter drum (pick face foaming or ejecting foam through scroll sprays) will suppress dust close to its source.

Jan 1, 1989

Determine safe practices for surface mine blasting near pressurized gas, oil, and water transmission pipelines. Background Surface mine blasters regularly have to address the issue of how blasting affects transmission pipelines that run near and sometimes through their permit areas. Regulatory approaches to blasting have ranged from no regulation at all to strict limits intended to prevent cosmetic cracks in plaster interior walls of homes, but they have not directly addressed the impact of blasting on nearby pipelines. Concerned with both productivity and safety, the mining industry and its regulators have requested guidance on safe practices for mining near pipelines. The Pipeline Research Group of the American Gas Association has sponsored studies of the effects of small close-in blasts because of vibration concerns related to the installation of new pipes into existing pipeline right-of-ways. By contrast, the recent study in which the U.S. Bureau of Mines (USBM) took part is the first addressing large-scale mining blasts.

Jan 1, 1995

The instrumentation specification in the National Academy of Engineering (NAE) report of March, 1970, set forth some rather general guidelines that the seismic surface system should follow. The fact that there was no comparable equipment in existence at that time, and the need to produce a system from presently available equipment, was spelled out in that document. The features that the system should include were listed, and included: • Quick and simple deployment • Portability • Battery-powered operation • All-weather operation • Computational simplicity and speed • High reliability and long shelf-life • Dual service for location and communication • Adaptability to widely varying seismic velocities. topography, and geologic structures • Minimum maintenance • Capability of continuous operation for extended periods, and • Reasonable cost Since that report, there has been a substantial amount of field work addressing the trapped miner detection and location problem carried out by Westinghouse Corporation under contract with the Bureau of Mines. Two complete surface systems have been designed, built, and field tested and substantial documentation has been produced on the mine environment and background noise using these systems. These systems, built from off-the-shelf equipment, have been designed with maximum flexibility in mind in order to explore what con¬figuration a field unit should have.

Jan 1, 1974

Provide a low-maintenance, reliable means of generating bubbles and controlling bubble size for column flotation. Approach Commercial sparger systems used in flotation columns to process minerals provide only limited means of controlling the size of bubbles generated and the rate of air injection. Generally, these limitations are a detriment to flotation performance, particularly in recovering coarse or fine mineral particles. In addition, conventional bubble generation systems require frequent maintenance, often requiring shut-down of the column itself for repairs. To permit greater control of the bubble size generated in the flotation column and to eliminate the counter-productive problems associated with the operation of current air sparger systems, the Bureau of Mines investigated alternative methods for generating bubbles. Based on the investigation, an external bubble generation system was designed, developed, and laboratory and commercially tested.

Jan 1, 1987

Reduce mine worker dust exposure by capturing airborne coal and quartz dust generated by a continuous mining machine. Approach Install a water-powered scrubber system operating at 1,000 psi on the side of a continuous miner boom. Dusty air under the boom is drawn through the scrubber, and cleaned air is discharged into the face return. How It Works Most coal mines use exhaust face ventilation to send fresh air over the miner operator, and contaminated air behind the line curtain to the section return. The difficulty with exhaust face ventilation is that the line curtain should be within 10 feet of the face for maximum effectiveness. If the line curtain is not extended properly, or water sprays for dust control are poorly installed, dust rolls back toward the operator. A scrubber mounted on the mining machine will effectively reduce this dust rollback and the dust in the return airstream.

Jan 1, 1989

By Jack E. Fraley

Poor lubrication reduces the life of wire hoist ropes when they are used in corrosive environments. Although lubricants are added to ropes during the manufacturing process, these lubricants can deteriorate during use, and it is often necessary to add more lubricant to both the interior and exterior of the rope while it is in service. The U.S. Bureau of Mines evaluated the effectiveness of synthetic lubricants, using electromagnetic nondestructive testing (NDT) to measure deterioration in ropes while they were in service. For nonpressurized lubricant applications, synthetic lubricants appear superior to petroleum-based lubricants in their ability to penetrate to the interior of a rope. Therefore, the synthetics offer better wear and corrosion protection.

Jan 1, 1990

By Doris M. Hyde

New mineral activity focused on increased petroleum exploration activities, while the established construction-oriented minerals sector operated without substantial change from previous years. After showing a 1 % real growth in the $154 million II gross domestic product (GDP) for 1983, preliminary estimates for 1984 indicated that the same growth pattern prevailed. The negative trade balance at midyear had worsened over the negative balance for the same period in 1983. An upward trend in import costs partly reflected the impact of Mexican inflation, which made that country's goods more ex-pensive and led to increased imports from North America and Europe. On the other hand, by midyear, the reexport trade with Mexico indicated an upward climb from the 1988 low of $12.7 million.

Jan 1, 1986

To quickly and more reliably measure the alignment and deflection of mine guides used to run skips and cages into a mine shaft. The Problem Conventional mine guide alignment measuring systems require the use of a plumb bob and tape measure. This method is not only laborious, but it is time consuming as well. Approach Aware of the drawbacks of the current measuring method, the Bureau of Mines designed a self-contained instrument system that can accurately perform vertical guide alignment and deflection measurements by remote control. How It Works The Bureau-developed instrumentation system, called the Guide Alignment Measuring System (GAMS), is based on conventional mechanical electronics using inclinometers and displacement transducers. The instrumentation system is attached to an operating skip or cage where it functions as a completely self-contained measurement system, operating in conjunction with nor-mal travel of the skip or cage. An on-board tape recorder or a mini-computer with memory can be used to record all telemetry.

Jan 1, 1987