Search Documents

Provide respiratory protection and a clean work environment for stationary or semimobile workers at minerals processing plants. Approach An Overhead Air Supply Island (OASIS) was developed which filters, conditions, and evenly disperses an envelope of clean air over a worker's head, thereby insuring reduced dust levels and a clean work environment. How It Works The concept for the OASIS derives from an earlier Bureau development of a canopy air curtain for continuous mining machines (see Technology News #21). In this application, the benefits of a reliable, self-contained, self-cleaning industrial-duty air filtration and distribution system are extended to the minerals processing field. The OASIS draws dust-laden room air into a filtration system, removing the dust and delivering clean air to a specific 16-square-foot area. It consists of: ? a self-cleaning primary filter ? a heater (cooling coil optional) ? an airflow distributor and secondary filter (combined)

Jan 1, 1985

By an Slo, J. J. Forbes

"INTRODUCTION This is the first of a series of information circulars dealing with the control of roof and the prevention of accidents from falls of rock and coal. These circulars are being published to focus attention of the coal-mining industry on this most prevalent source of fatalities and injuries and to present factual information that should be helpful in reducing loss from these causes.Records of fatal accidents in the coal mines of the United States, from all causes, have been kept since 1906; during this period approximately 30,000 men have been killed by falls of rock and coal in the bituminous-coal mines, and more than 7,000 men have lost their lives in the Pennsylvania anthracite mines from the same causes. From 1906 to 1930, about 900 men were killed annually by falls of rock and coal in bituminous-coal mines, and about 200 men were killed annually in anthracite mines during the same 25-year period. From 1931 to the present time, the number killed annually from falls of rock and coal has averaged more than 500 men in bituminous-coal mines and about 125 men in Pennsylvania anthracite mines.Numerically the record of accidents from falls of rock and coal shows improvement, but on a percentage basis and on a million-man-hours-of-exposure basis little, if any, improvement has been made during the past 40 years. The cold fact is that, year after year, about 50 percent of all those killed in coal mines in the United States lose their lives from falls of rock and coal."

Apr 1, 1948

By Parviz F. Rad

The Bureau of Mines conducted rock-cutting experiments under constant normal force and constant penetration in an effort to correlate laboratory data with those obtained in the field. Both independent and interacting groove spacing regions were studied, and optimum and critical cutter spacings were determined. For the laboratory work, the effects of specific energy, muck weight, groove depth, cutting coefficient, and size distribution of the muck for both independent and interacting grooves were studied. For field operations, forward thrust, torque, advance rate, and muck size distribution were the parameters studied. Satisfactory correlation is obtained between laboratory cutting results and field performance data.

Jan 1, 1974

Improve underground long-hole drilling efficiency and safety by developing a lightweight, easily transportable drilling pust that can be adjusted to fit a range of mine opening heights. Background Standard one-piece commercially available steel posts weigh approximately 10 pounds per foot. Transporting these posts underground and carrying them over obstacles and through small mine doors is very difficult. Because the length of a one-piece post cannot be adjusted, variations in mine opening height at the drilling site must be accommodated. This is accomplished by stacking several wooden blocks to form a base for the post, resulting in a dangerously unstable drilling setup. The only alternative to this unstable setup is to obtain a longer post. There problems can be reduced by the use of a two-piece telescoping aluminum post having a 3-foot adjustment range in 6-inch increments. The two-piece extendable post will be easy to transport and carry underground. It will fit any opening height within its adjustment range. One large wooden block is used as a base and one cap block is used at the top to bear against the mine roof. This arrangement results in a stable, rigid setup.

Jan 1, 1990

By Michael J. Brnich

Since 1991, Pittsburgh Research Center (PRC- formerly part of the Bureau of Mines) researchers have recorded extensive interviews with 30individuals who are experts in the area of mine emergency response. These individuals, who have an average of 35 years of mining experience and 29 years of mine emergency response experience, related stories and observations from events that they experienced during their combined 850 plus years in mine emergency response. The purpose of this effort was to gather information that could be passed onto both today?s and tomorrow?s mine emergency responders to train and guide them in handling future events. This is the second of two articles which report experts responses to questions about training for future mine emergencies. During the interviews they discussed how training should be conducted, who should be trained, and what topics should be included. This article will cover the third area: Topics that should be included in training for mine emergency response managers.

Jan 1, 1997

By B. Dimitriades

Experimental work has been done to refine and to confirm an analytical procedure by which gas-liquid chromatographic (GLC) spectra are interpreted from retention time data alone. The rationale of this spectra interpretation technique involves whether or not a given peak invariably represents the same component or component mixture; if not, what factors influence changes in peak identifications. To answer these questions, peak-identification procedures, based mainly on the use of subtractive columns, were developed and applied to interpret GLC spectra of several exhaust (and fuel) samples.

Jan 1, 1972

By Bruce T. Olenchuk, Wils L. Cooley

Electrical grounding is essential for the safe operation of power systems. A low-impedance path to ground is necessary to prevent the possibility of dangerously high potentials in human work areas. If for any reason this ground connection becomes faulty, a serious hazard may exist. One reason for faulty ground connections is ground bed corrosion. Corrosion of electrical ground rods has plagued the power industry and appeared in coal mine power systems. This paper will investigate ground rod corrosion, its cause, and possible solutions. Included is an evaluation of various ground rods for their ability to resist corrosion under stray current conditions. -The first known study of X-it3 Rod Corrosion is also presented.

Jan 1, 1979

By Douglas Talley

This report describes a 4-inch diameter borehole probe which contains a low light level TV camera, magnetic compass, light illumination source, bottom/water detector sensor and a pointing angle sensor. The camera viewing angle is at a right angle to the probe's body. All data from the sensor is multiplexed into the closed circuit camera video for transmission on a single 50 ohm coaxial cable to a surface control unit. Likewise control of the probe's power, zoom lens, focus, panning and aperture is accomplished via a down-link multiplexed on the same cable.

Jan 9, 1984

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

3. Preliminary Evaluation of Mine Sealing Techniques As the first stage in the development of a technique for the remote sealing of mines, a state-of-the-art survey of various mine sealing techniques was conducted. This was expanded to include a review of different materials offering some potential for use as a mine sealant. Techniques for the remote placement of materials for other applications were evaluated, and system concepts for dis¬tributing remotely placed materials were developed. This preliminary review led to the development of a functional description of a general mine sealing technique to meet the specified conditions. Various potential system configurations were synthesized. These were subjected to a preliminary evaluation based on estimated confidence in system performance, development risk, cost, and sealing time. Based on this preliminary evaluation, promising mine¬sealing techniques were selected for further development. This section presents a review of the following: (a) Techniques for constructing permanent seals from within a mine. (b) State of the art in remote sealing for mine fire control. (c) Techniques for remote placement of materials for other applications. (d) Systems for distributing remotely placed material. (e) Materials for mine sealing. (f) Synthesis of remote mine sealing concepts.

Jan 1, 1973

By Wilbur I. Duvall

The Bureau of Mines presents a theoretical solution for the stresses and displacements in an infinite elastic plate containing a circular hole whose boundary is subjected to applied shear loads over four separated arcs. The results for the applied shear loads can be superimposed on the results for applied radial loads, given in a previous publication, to obtain a complete two-dimensional approximation of the stresses and displacements induced in the rock by tunnel boring machines anchored in a circular tunnel by means of four props. Analysis of the various solutions shows that the tangential tensile stresses induced on the boundary of the circular tunnel by applied radial loads can be minimized in the roof and floor of the tunnel by the application of appropriate shear loads to each of the four props. Thus when planning tunnel boring operations, consideration should be given to the in situ stress field in the rock and the induced stresses in the rock resulting from the applied radial and shear loads produced by the props of the boring machine.

Jan 1, 1968

By M. J. Kovalik

The effects of the process variables on the production of chemical coke on a chain grate stoker, a type of traveling grate, were studied. Six bituminous coals, ranging in volatile matter from 16.7 to 43.8 percent, were successfully carbonized, yielding chemical coke with acceptable physical properties. The coke yields were dependent on the volatile-matter content of the coal. The air fuel ratio had the most marked effect on the yield and characteristics of the resultant coke, and the general furnace performance. Results can only be predicted; the actual yield and quality of coke obtained from any given coal can only be determined by actual tests using the optimum processing variables to obtain a coke with minimum volatile-matter content and to retain as much of the fixed carbon in the original coal as possible.

Jan 1, 1967

By William P. Diamond

A 3-inch pilot hole was directionally drilled to intercept the Freeport coalbed horizon horizontally at Mather, Pa., as part of a Bureau of Mines degasification project. The original concept was to continue the horizontal drilling into the coalbed, after the initial intercept, with a total of three horizontal holes eventually being completed. However, the erratic thickness (0.0 to 4.3 feet) of the Freeport coalbed at Mather was not sufficient to support the horizontal drilling degasification technique, and the site was abandoned after six attempts to locate adequate continuous coal thicknesses. The drilling of coreholes in the immediate vicinity of proposed well paths to evaluate coal thickness is essential prior to future slant hole operations. Although mechanical failures of the new directional drilling equipment, mud pump and rig breakdowns, directional control problems, and exploratory horizontal drilling in the Freeport horizon more than doubled the anticipated cost of the pilot hole, continuing improvements in directional drilling equipment and techniques should significantly reduce the time and costs of future drilling operations.

Jan 1, 1977

By Paul T. Allsman

SCIENTIFIC inquiries concerning phenomena that may influence mining technology were widely publicized during the year. The deep-hole drilling project "Moho," 3 the use of nuclear explosives underground, and the recovery of minerals from the depths of the sea became subjects of scientific and general discussion. The mining industry continued to watch these developments with keen interest: but its more immediate concern was the increasing tempo of competition between mineral commodities, the domestic producers of these commodities, and foreign sources of supply. The competitive situation has intensified the industry's efforts to develop more efficient new mining methods, as well as to improve the efficiency of present practices. The attitude of the industry was well illustrated by rapidly expended use of low-cost ammonium nitrate explosives, the establishment of rigid schedules for equipment maintenance, and close attention to the detailed costs of production. The complexity of planning a new coal mine is aptly illustrated by the editors of Mechanization in the April 1959 Issue, in which they outline the cost of developing a mine and the various problems, factors, and decisions involved.4

Jan 1, 1960

By Robert C. Gabler

The extraction of metals from coal ash was investigated by the Bureau of Mines in an effort to produce a more environmentally acceptable waste and offset waste disposal costs with recovered metal values. The research was conducted in two steps: determination of the parameters that affect extraction of metals from coal ash and development of extraction-recovery procedures. Data obtained indicate that the major parameter affecting the extraction of metals from coal ash is the calcium content of the ash. Other parameters such as furnace type and operating temperature had much smaller effects on metal extraction. Two procedures were studied for metal extraction: an acid leach procedure for high-calcium ashes and a lime sinter-acid leach procedure for low-calcium ashes. An alumina product was recovered that, with sufficient washing, meets Hall cell specifications. The leach residues pass the EPA EP Toxicity Test and are thus nonhazardous wastes available for a variety of uses.

Jan 1, 1983

By Francis R. Redfern

Newton's method of solving a nonlinear equation is employed to develop a least-squares acoustic emission source location method in which the spatial residuals of the location equations are minimized. These residuals, related to the distances from the least-squares source location perpendicular to the surfaces described by the location equations, permit location error to be estimated to first order along the spatial axes. The solutions obtained by this method are the best spatial solutions to the location equations in the least-squares sense. Also presented is a procedure by which the geometrical control of a transducer array can be evaluated using the rate of change of source location with fractional velocity change.

Jan 1, 1982

By Robert F. Chaiken

A novel approach to eliminating environmental and public safety hazards that are associated with fires in abandoned coal mines and waste banks involves the use of in situ combustion technology developed by the Federal Bureau of Mines to accelerate the burning of the wasted coals in place. This technology would be used under exhaust ventilation control conditions that would allow for total management of the hot gases produced. Combustion stoichiometries would be optimized to minimize unburnt combustibles and to maximize the heat content of the gas products, which will be exhausted at one or more fan locations. When necessary, scrubber systems would be employed to remove air pollutants, such as sulfur dioxide; heat utilization systems (process heat, steam, and electricity) would also be employed to offset operational costs. Ultimately, complete burnout would solve the fire and acid water formation problems of the abandoned coal mine or waste bank. Pertinent technical data for burnout control are derived and discussed in terms of the important material and operational parameters. In general, it is believed feasible to operate a burnout system in an existing abandoned mine or waste bank fire at thermal power levels in the range of 10 to 100 Mw, and at exhaust gas temperatures of 1,000° C (1,830° F).

Jan 1, 1980

By George H. Johnson

An evaluation of the diamond-bit-performance data accumulated from core-drilling cherty limestone and cherty dolomite reveals that the percentage of core recovered and the physical characteristics of the bits and diamonds used are economically significant. One of the established trends, of particular interest to those engaged in diamond drilling, is that bits set with small, low-quality, West African drill bort are the most economical. Detailed analysis of the factors that affect diamond-bit performances, such as diamond size and quality, bit size and type, percentage of core recovered, and the physical characteristics of the bit matrices are assessed in the tables, charts, and discussion.

Jan 1, 1958

By M. L. Skow, Maurice Deul, M. G. Zabetakis

This Bureau of Mines report presents a brief summary of the explosion trends in United States coal mines for the past 160 years. These trends show that in spite of the overall improvements in mine safety, the number of fatalities from ignitions of methane has actually increased in recent years. Suggestions are made of procedures that can be utilized to reverse this trend.

Jan 1, 1972

By D. L. Paulson

The Bureau of Mines is investigating pyrometallurgica1 and" chemical methods to recover valuable constituents from metallurgical dusts and slags. Under this program a technique was developed to recover iron from molten copper smelting furnace slags by carbon injection. Slags from gas-fired reverberatory and electric copper smelting furnaces were treated in an 800-kva electric-arc furnace by injecting coke breeze into the bottom of the molten bath. Over 95 pct of the iron and over 90 pct of the copper contained in the smelting furnace slags were recovered, while up to 85 pct of the carbon injected into the system was utilized. It is anticipated that the metal product containing approximately 95 wt-pct iron and 2 wt-pct copper will be a satisfactory medium for recovering copper by cementation.

Jan 1, 1977

By John C. Edwards

The Bureau of Mines has developed a time-dependent droplet vaporization model (in the absence of forced convection) that can be applied to the vaporization of liquid Halon 1301 droplets (vapor pressure at 300 K = 14 atm) sprayed from an extinguisher. It was found that rapid surface vaporization quickly lowers the droplets' surface temperature very near to the boiling temperature, and the vaporization becomes diffusion controlled. Although the lifetime of the droplet is proportional to the square of the initial radius of the droplet, the elapsed time prior to complete droplet vaporization is not proportional to the square of the droplet radius, as an equilibrium model would indicate.

Jan 1, 1982