Search Documents

By C. H. Elder

An experimental degasification program using a vertical borehole and vacuum pump to drain gas from the gob area of a longwall panel was successful at Bethlehem Mines Corporation, Cambria Division, No. 33 coal mine. Sixty-one million cubic feet of methane has been exhausted during a 9-month period. Daily production time in the panel increased as a result of lower methane levels in the returns. Removal of large quantities of methane in this way and the exclusion of it from the ventilating system will provide reduced cost in mine ventilation and provide a safer environment for the mine.

May 1, 1969

By W. L. Staker

The Bureau of Mines investigated methods for selectively eluting mercury, silver, and gold from strong-base anion-exchange resins, including Rohm and Haas resins lRA-430 and 900 and Dow Chemical resins 2lK, SMA-I, and SBR. Resins were typically loaded to 145 oz/st of each metal. Loaded resins were eluted with H2S04, NaCl-H Cl, NaOCl, and NaCl04 solutions. The resins tested had similar elution characteristics for mercury and precious metals. The best selective elution scheme was achieved by eluting in a column with 2N H2S04 to recover 99 to 100 pct Hg, with 200 giL NaCl in IN HCI to rec;ver 99 to 100 pct Ag, and with 2M NaCl04 to recover 79 to 89 pct Au.

Jan 1, 1987

By Willard L. Hunter

The separation of tantalum and columbium by solvent extraction was under-taken as part of the Bureau of Mines research program to improve methods for extracting, separating, and reducing these elements to metal. The diethyl ketone aqueous HCl-HF system was one of several systems studied to determine the effect of metal and acid concentrations in aqueous solutions upon the transfer of tantalum and columbium into selected ketones. The tantalum-columbium oxide mixture used in this investigation was obtained by chemical extraction from Geomines slag. The investigation showed that tantalum 99.4 percent pure and columbium 97.2 percent pure can be produced by the selective transfer of tantalum into diethyl ketone from a solution of 2-N HF and 1-N HC1. The relatively low acid concentration necessary for tantalum transfer and the excellent selectivity of the system recommend its use for the separation of tantalum and columbium.

Jan 1, 1961

Provide an accurate, simple, alternative means of evaluating the safety of mine electrical ground systems which has little or no negative impact on mine productivity. The Traditional Evaluation Method The Code of Federal Regulations requires all mines to safely ground their power systems to earth. Effective earth grounding reduces shock hazards to mine workers operating electrical equipment, protects equipment from damage by voltage transients, and provides a means of detecting and locating ground faults. Once an earth ground bed has been constructed, its level of resistance has traditionally been used to gauge the safety of the entire grounding system. Bed resistance measurements are normally performed using a ?fall of potential? technique with a current return electrode placed at a remote location, If the resistance measured is acceptably low, then the bed is assumed safe.

Jan 1, 1985

By Daniel Edelstein

The supply of arsenic trioxide in 1982 was adequate to meet domestic demand. Allocation of supply by major domestic and foreign producers that began in 1977 ended during the first quarter of 1982. Major demand was about evenly divided between industrial chemicals and agricultural chemicals. Domestic Data Coverage.-Commercial- grade arsenic trioxide and arsenic metal were produced by only one U.S. company. In order to prevent disclosure of proprietary data, arsenic production data have been withheld.

Jan 1, 1983

Simplify the spraying of sealants onto coal mine roofs. Approach A nonclogging system in which dry-fed sealant is mixed with water down-stream of the spray nozzle, has been developed and tested. How It Works The two-channel nozzle of this spray discharges two separate flows, a mixture of air and dry sealant from a central cylinder, and an encircling spray of water from a concentrically mounted water ring (a ring-shaped manifold). Downstream of the nozzle, the water mixes with the air and sealant to form a wet sealant spray that adheres to mine surfaces with very little rebound. (See photograph.) Extensively modified commercial spray machines are used to feed the sealant to the spray nozzle smoothly, without raising dust. Plugging of the nozzle is practically eliminated by two self-cleaning design features of the nozzle. These are the air gap and the tapered bore of the cylinder, (See drawing.)

Jan 1, 1979

Enhance the critical skill of hazard recognition among miners by providing quality training that can help jot performance and lead to a higher degree of safety in the workplace. Background In mining, as in many other occupations, the safety of the worker depends on his or her ability to recognize hazards in the workplace. Some of the information needed by the miner for recognizing potential areas of danger is available in the form of visual cues found throughout the mine. One aspect of the dynamic mine environment it which the task of hazard recognition is critical for al workers is that of ground control. Regardless of job responsibilities, every worker is continuously exposed to roof rib, and floor hazards. Fatality injury data for the "underground coal" segment of the mining industry continue to show that about half of all fatalities are due to falls of ground each year. It is hypothesized that some of these accident, can be prevented if miners are better able to recognize visual cues that forewarn of potential roof and rib problems.

Jan 1, 1992

By J. D. Corrick

Research was conducted to develop operating techniques and define some of the limiting parameters for microbially converting hydrous calcium sulfate to hydrogen sulfide. The work was carried out in either glass stoppered flasks or anaerobic fermentors. Using the criteria of pH, temperature, number of bacteria per milliliter of test solution, and hydrogen sulfide produced, it was shown that hydrous calcium sulfate could be microbially converted to hydrogen sulfide at a rate of 7.3 g H2S/1 of fermentor volume per 24 hours. The various parameters defined were pH, temperature, and medium exchange rate. These were shown to be a pH range of 7.2 to 8.8, a temperature range of 30° to 35° C, and a medium exchange rate of 70 percent of the ferment or volume per 24 hours. It was also shown that a daily waste was between 50 and 77 percent as effective as sodium lactate in supporting the production of hydrogen sulfide and that by utilizing a gas to purge the fermentation system, a 1.7-fold increase in hydrogen sulfide was obtained.

Jan 1, 1970

By Robert F. Holub

The Bureau of Mines has made a study of the magnitude of the variations of radon daughter mixtures, with the objective of determining whether these variations reflect the existing physical conditions in uranium mine atmospheres or if they are merely random or systematic errors. To accomplish this, many data have been plotted using a triangular graphing technique which shows that plateout affects RaA more than RaB or RaC, and that it is impossible to find simple correlations between working level ratios, radon daughter mixtures, and age.

Jan 1, 1978

By R. V. Ramani, V. T. Burgos, J. A. McClay

The systems contributing to the cost analysis, and the flow of data input and output related to these systems, are brought into focus in Figure 6. The various sub-systems of the Master Design Simulator provide the raw operating data basic to the cost model which, operating independently, accumulates the raw input, assigns costs to this data by standard or modified costing procedures, manipulates the costs into standard formats and outputs the data for managerial evaluation. Cost Modeling Direct costing methods are not complex in the sense that elemen¬tary arithmetic is employed using the same basic relations for each cost category. The basic cost model relations described above are illustrated in Figure 7. The greatest difficulty encountered in the transition from a dy¬namic systems simulation model to a costing model is the time frame of the input and output data. Dynamic simulation models utilize a small time increment, on the order of seconds or fractions of seconds, to analyze system operations and interactions. On the other hand, for cost computation and reporting, the smallest relevant time unit is the shift, with reporting periods expanding to days, weeks, months, and years. Complications arise in the accumulation of data for the various report periods due to the use of the Gregorian calendar by modern so¬ciety. The potential for simulation for the life of the mine, possibly in excess of 50 years, increases the complexity of the costing process

Jan 1, 1975

By R. T. Stull, L. E. Geyer

"Previous Work:As outlined in previous papers* ond clays for graphite crucibles have been tested at the plants of the Detroit Lubricator Co., and the Detroit Copper and Brass Rolling Mills, Detroit, Mich.These tests indicated that there were two American clays (Missouri pot clay and Illinois kaolin) that tested better than the Klingenberg (German) clay. Dorset (English) ball clay was tenth in the list.Making the Crucibles:After it had been determined that American clays can be used successfully in graphite crucible manufacture and service, the next step in the investigation was to determine the value of American graphites as compared to the foreign, These final tests were carried out at the plant of the Detroit Lubricator Co., through the courtesy of Mr. G. B. Duffield. The crucibles, as previously. were made at the plant of the Vesuvius Crucible Co., Swissvale, Penna., from a formula compiled by the Bureau of Mines and under the supervision of Bureau engineers.The graphites to be tested were given an initial to indicate their source. The number of crucibles made and shipped are set forth in Table 1."

Nov 1, 1923

By Fred N. Kissell

Methane flows and pressures were measured in mines in the Pittsburgh, Hartshorne, and Pocahontas No. 3 coalbeds. From the data, the permeability of each of these coalbeds was computed. It was found to depend strongly on the type of coal and on the amount of water in the coalbed, and it was found to increase with time. All of the coalbeds had a high-permeability zone adjacent to the face or rib, and the Pittsburgh bed exhibited directional anisotropy. Surprisingly, little or no overburden effect was observed.

Jan 1, 1972

By J. K. Whyatt, B. G. White

Various methods of monitoring slip movements on bedding planes, as well as examination of rock burst damage in stopes, suggest that many rock bursts in the Lucky Friday Mine are closely associated with these movements. Slip displacements along bedding simultaneously reduce the physical dimensions of stopes and increase compressive stress along stope margins. Such changes, in turn, contribute directly to sudden failures of rock and cemented sandfill surrounding stopes. We believe that the reduction of rock burst hazards must be based on a clear understanding of the basic mechanisms involved. The current work emphasizes the mechanical role of wall rock movement and seismicity in generating conditions that promote rock burst damage. Based on our interpretations of these mechanisms, we briefly address several hypothetical practices that could influence rock burst hazards in similar mining situations. The overall goal of this research is to advance the NIOSH mission of improving the health and safety of the nation’s workers.

By B. T. Brady

Results of a study are presented of the effect of low radial reinforcement pressure on the postfailure characteristics of two types of granite, a sandstone, and marble. The low radial reinforcement pressure is applied to the rock surface by a gooch rubber sleeve. The gooch rubber sleeve provides a radial pressure of less than 1 psi pressure to the rock surface. This method of support gives an average strength increase of approximately 8 percent to the fractured rock sample.

Jan 1, 1973

By Michael J. Brnich

Since 1991, Pittsburgh Research Center (PRC- formerly part of the Bureau of Mines) researchers have recorded extensive interviews with 30 individuals who are experts in the area of mine emergency response. These individuals, who have an average of 35 years of mining experience and 29 years of mine emergency response experience, related stories and observations from events that they experienced during their combined 850 plus years in mine emergency response. The purpose of this effort was to gather information that could be passed onto both today?s and tomorrow?s mine emergency responders to train and guide them in handling future events.

Jan 1, 1997

By Lewis V. Wade

This Bureau of Mines work was performed to theoretically determine the effects of specimen radius and specimen boundary conditions on the stress state in the rock near the anchor for rock specimens used to investigate expansion anchor behavior. Finite element analyses were performed on mathematical models of varying radius and boundary conditions. A review of the results of these analyses revealed a definite convergence of all stress measures considered as the specimen radius increased. There was, however, a significant variation in all stress measures as the specimen diameter increased from 8 to 12 inches.

Jan 1, 1973

By Jay F. Colinet, John A. Organiscak

In This Chapter [Which dust source to address first How much air and water are needed Keeping dust out of the walkway Moving workers upwind Dealing with the stage loader-crusher Gob and wing curtains to aid airflow The shearer-clearer system Modified support movement practices and Dust control for future longwalls ] Controlling longwall dust is not easy. Longwall production levels are high, and there are several different sources of dust to contend with. If dust levels are high, the initial effort should be devoted to finding which source is the cause. Then, efforts to reduce dust can be concentrated where they will have the most impact. To control dust at longwalls, a large amount of ventilation air and spray water must be used. The water must be sprayed correctly so as not to blow dust into the walkway. Techniques to change local airflow patterns can be helpful. The shearer-clearer, as well as gob and wing curtains, are examples of such techniques. DECIDING WHICH DUST SOURCE TO ADDRESS FIRST [If a longwall is out of compliance with dust standards, knowing where the extra dust is coming from helps to get back in compliance quickly.]

Jan 6, 2003

By Kevin Michael, David C. Byrne

In previous issue of Spectrum (October 1999, 16/4), a system of measuring the attenuation provided by insert-type hearing protectors was described, That report described experiences using the FitCheck (Michael & Associates, Inc.) system in a pilot project involving the steel industry during 1998.[ ]

By Jack C. White

Studies were made to determine the character and distribution of the copper lost in copper mill tailings. Acid soluble (oxide) and acid insoluble (sulfide) copper were determined for heavy-liquid sink and float products of screen-sized fractions from 12 copper mill tailings. In most of the tailings studied, the coarse-size fractions are higher in copper grade than the respective bulk tailings, high in sulfide copper, and low in oxide copper. Oxide copper occurs predominantly in the minus 325-mesh "slimes." Microscopic examination of heavy-liquid sink products indicated that recovery of liberated copper sulfide minerals is complete in most mills, and that copper minerals not being recovered are locked with gangue particles. Additional copper could probably be recovered from most tailings by size classification, scavenger froth flotation of the coarse fraction, and regrinding of the concentrate to achieve liberation of the locked sulfides.

Jan 1, 1971

By Oscar Lee

"Flotation is generally regarded as a process that is only applicable to metallic minerals. However, its scope is now known to be greater than this, because some of the nonmetallic minerals are floatable, such as graphite, sulphur, and fluorite. Recent observations show that limestone may be added to the list of floatable nonmetallic minerals. Such work is being done on a laboratory scale at the Southern Experiment Station (Tuscaloosa, Ala.) of the Bureau of Mines, Department of Commerce, where experimental magnetic concentration of the low-grade iron ores of the Birmingham district is in progress. Certain experiments have demonstrated that the limestone may be floated from the magnetic log-washer tailing, and then incorporated in the iron concentrate.If the loss of lime could be prevented, some ores though low in iron and high in insoluble contain enough lime to make their concentrates self-fluxing. Since this loss in the magnetic log-washer can not be avoided, the Time must be recovered from the tailing by some method and added to the magnetic iron concentrate before sintering. Then the resulting concentrate will be self-fluxing.While seeking a suitable means of treating the tailing for recovery of lime, flotation was tried. It was at once evident that this method had possibilities, during the early part of the investigation, soap solution made from a common soap was used as a flotation reagent. The froth obtained was a fairly good lime concentrate. This result was an important clue, and led to tests with the use of such reagents as oleic acid and sodium oleate. Later, cresol, creosote, coal tar and other similar flotation reagents were tested in combination with the oleic acid and soap solutions. As a result, oleic acid and cresol used together were found to be satisfactory.The tailing from the magnetic log-washer is in excellent physical condition fur flotation. The iron ore had been ground in a ball mill to 100 mesh for magnetic concentration. Hence the bond between the lime carbonate and the other constituents of the tailing was well broken."

Apr 1, 1926