Search Documents

By J. J. Geraghty

U.S. Bureau of Mines researchers investigated the development of an innovative transport system for underground coal mining. A one-half commercial-scale bench model was constructed. Novel magnetic levitation (mag-lev) technology was developed. Frictionless and contact-free transport of a prototype materials container and payload has been demonstrated.

Jan 1, 2010

By Jon C. Volkwein

Dust concentrations inside and outside enclosed cabs on several types of mining machinery were measured by the Bureau of Mines. Results indicated that properly enclosed cabs can offer significant dust protection for machine operators. Recommendations for improvements in cab technologies were discussed.

Jan 1, 1979

By H. Foster Bain

Ten years ago there was no general , country-wide service for the systematic training of miners in matters relating to safety . A beginning only had been made at a few scattered points . Under the old conditions each man was left largely to look out for himself in meeting the hazards of his day's work, and the foreman , shift bosses , and superintendents chiefly relied upon improvision when major accidents occurred . So long as the mines were small and the workers highly intelligent and well trained in routine mining methods , and when too , the pressure for output had not yet speeded up industry to the extent it has since those days , there was something to be said for this lais- sez faire attitude . When , however , the rapid expansion of industry lead to the introduction of new and little trained labor and to units of production of greatly increased size , the natural dangers of mining were greatly intensified . An accident in a small mine affects only a few; the same accident in a large mine , unless proper precautions have been taken , may cost the lives of many . The public does not generally recognize that the greatly increased outputs of the mines , of coal mines in particular , have been in recent years , obtained from substantially the same number of miners as ten years ago but with a personnel not nearly so well trained in mining . It is inevitable under : such conditions that more care must be devoted to avoiding accidents and much more elaborate preparations made for meeting them . In the years immediately preceding the establishment of the Bureau of Mines this speeding up of industry , change in the character of mine labor , and increasing hazard had all begun to be felt . Immediately prior to the organization of the Bureau of Mines , public attention had been drawn to a series of disastrous coal-mine explosions , to the increasing frequency of these disasters , and to the terrible loss of human life . resulting therefrom. One of the first problems , therefore ; confronting the Bureau was clearly that of finding methods of reducing the number of such disasters and lessening the severity of those that continued to occur . Toward this object were immediately directed the energies not only of the Bureau of Mines but also those of State mine inspectors , mine operators and various other agencies , all of whom were urged to cooperate in this great humanitarian work. The results of this work naturally cannot be measured by figures only . Work for increasing the health , safety , comfort , and happiness of human beings may not be gaged with mathematical precision . But certain features of this work as revealed by the record from year to year are of much interest . ”

Apr 1, 1921

By J. I. Paige

The Bureau of Mines, U.S. Department of the Interior, conducts research on methods to minimize the requirements for mineral raw materials through conservation, substitution, and increased minerals and metals recovery from primary and secondary domestic resources. To further this goal, prior Bureau research had devised a pyrometallurgical technique (RI 8211) to recover metallic iron and copper from molten copper smelting furnace slags by carbothermic reduction. As a continuation of this Bureau research on the carbon injection technique, reverberatory and electric furnace slags were treated in an 800-kva electric arc furnace by simultaneously top feeding the slag and injecting coke breeze into the bottom of the molten bath. Results of the tests show that 76 to 89 pct of the copper and up to 48 pct of the iron contained in the smelting furnace slag were recovered in a metallic phase, while 56 to 82 pct of the carbon injected into the sys-tem was utilized as the reductant. Laboratory evaluation has shown that the metal product, which contains 86.9 to 95.0 wt-pct iron and 1.3 to 4.1 wt-pct copper, will be a satisfactory medium for recovering copper by cementation. The expected energy consumption for the process is 110 kwhr per ton of molten slag treated and 520 kwhr per ton of solid material charged.

Jan 1, 1982

By T. E. Gray

This report describes the preparation characteristics of the more significant coal beds in Washington County, Pa. It is one of a series planned to determine coals suitable for producing metallurgical coke, either as mined or after beneficiation. More than 15 million tons of coal was produced in Washington County in 1956; 89.8 percent was cleaned mechanically in 10 cleaning plants. The Bureau of Mines has estimated that 2,280 million tons of recoverable coal remained in beds 28 inches thick or more as of January 1, 1954.

Jan 1, 1959

By Martin H. Stanczyk

Ultrafine grinding of the industrial minerals mica, pyrophyllite, talc, marble, barite, and fluorite was accomplished using the Bureau-developed and patented attrition-grinding process. The materials, representing minerals of diverse physical characteristics, were batch ground in a 10-inch-diameter machine using statistically designed experimental test programs. The tests were made to determine large effects of variables such as feed pulp density, grinding medium size, and quantity of the electrical energy consumed during grinding on product particle size and bulk density. In designing the test programs, it was assumed that there was no interaction between the variables. Relatively coarse commercial flotation concentrates of mica, barite, and fluorspar and mine-run products of pyrophyllite, talc, and marble were readily ground into subsieve size ranges. Considering the great amount of particle size reduction obtained, the electrical energy requirements for grinding were very low. In general, the test results indicated that the best conditions for particle size reduction were approached when grinding with the coarser fraction of sand grinding media, the higher-sand-to-mineral weight ratio, and the higher feed pulp density.

Jan 1, 1972

By Martin Hertzberg

In this Bureau of Mines report, the optical detection of fires and explosions is considered fundamentally. The measured spectral radiances from methane-air ignitions are compared with the background irradiances from stray and ambient sources, and with the spectral sensitivites of various sensors. The comparison naturally suggests the optimum spectral ranges and signal processing logic that can uniquely characterize the ignition event. Both ultraviolet (UV) and infrared (IR) are considered. Several alternate sensing methods are proposed and discussed. The development and testing of an IR system designed for use in ignition suppression devices in mines is described.

Jan 1, 1975

By W. E. Robinson

Sixty samples, selected from a 2,300-foot core of the Green River Formation in Colorado, were studied to ascertain differences in the structure of the organic material present in the oil shale samples. Emphasis was placed upon relating differences in the aromatic content of the insoluble kerogen and the alkane content of the extractable material obtained from the selected samples. The methods used in determining these differences consisted of fractionation of the soluble material, carbon and hydrogen analysis, volatile material determination, carbon residue determination, oxidation rate determination, and infrared analysis. In general, it was concluded that the organic material in this core does vary in chemical structure and that same of these variations resulted from factors related to depth of burial. Other observed changes in structure of the organic material were not depth-dependent and resulted from other factors such as source material variations, biological alterations, or ecological differences.

Jan 1, 1971

By J. P. Baur

The sensitivity of radiochemical techniques makes possible the study of the initial-stage sulfuric acid leaching kinetics of chalcopyrite and other copper sulfide minerals. This Bureau of Mines study of the initial leaching of chalcopyrite used techniques to evaluate the molecular and electrochemical processes. High-grade Transvaal chalcopyrite was neutron-irradiated in a TRIGA reactor4 to produce radioisotopes copper-64, iron-59, and sulfur-35. Dissolution rates were measured in the time interval zero to 60 minutes, during which time significant anomalies were observed. First was an initial period of rapid dissolution lasting a few minutes; second, an arrest or ?plateau? region usually lasting from 6 to 10 minutes; third, a second period of dissolution of lesser rate than the first. The effects of solution variables such as pH, oxygen partial pressure, and ferric ion concentration at different temperatures were measured.

Jan 1, 1974

By David P. Lindroth

The Bureau of Mines has developed and successfully tested a hangup clearance module for use in clearing hangups in underground mine chutes and ore passes. The Bureau's tests showed that the hangup clearance module can be effectively used to clear mine hangups. Furthermore, it is believed that clearance using this module is quicker, safer, and more efficient than the method currently used. The hangup clearance module uses a ballistic disk explosive charge that can clear hangups located as far as 50 feet (15.2 m) from the position where the charge is detonated. Mine personnel can therefore set up the module and the charge it contains without being exposed to dangerous areas. This report describes the principles of operation of the module, provides data and drawings for its construction, and gives instructions for its setup and use. The report also summarizes the development of the module, briefly discusses preliminary and underground tests, and lists the current and potential applications of the hangup clearance module to underground mining.

Jan 1, 1982

By John P. Coughlin

Software techniques developed by the Bureau of Mines Denver Research Center for real-time microseismic data analysis are presented. These techniques focus on the simple acquisition of P-wave arrival times and their use in event location. The paper discusses in detail software techniques to separate microseismic events from mining noise such as drilling and from very large events such as rock bursts. Incorporation of these techniques has enhanced the reliability and accuracy of computer-based monitoring of microseismic activity in ongoing research by the Bureau.

Jan 1, 1982

By J. D. Dixon

The Bureau of Mines has developed structural design data for unreinforced concrete tunnel linings in the form of stress and deflection coefficients from which bending, axial, shear, and boundary stresses, moments, thrusts, and shear forces, and structural deflections can be determined at any point on the lining. Results were obtained by structural analyses of nine concrete-lined tunnel configurations subjected to 22 biaxial load conditions. The tunnel configurations include three basic shapes, circular, rectangular, and horse-shoe, with dimensions based on designs evolved by the mining industry. These analyses were made by the direct stiffness matrix method, a computer-oriented procedure. Numerical results agree closely with those obtained experimentally.

Jan 1, 1969

By H. H. Fields, T. W. Goodman, Joseph Cervik

The Bureau of Mines conducted research to determine the effectiveness of long holes drilled in solid virgin coal in degasifying an area of the Pitts- burgh coalbed showing that horizontal holes drilled into a virgin coalbed from the bottom of any shaft will effectively remove methane gas in commercial quantities from the Pittsburgh coalbed. The in situ pressure at a depth of 214 feet into the coalbed and the average gas and water flows from the five degasification holes were 3 lb/in2 gage and 860,000 ft3/d and 1.7 gal/min, respectively. On June 19, 1975, after 593 days of degasification, a compressor was installed and pipeline quality gas was introduced into a commercial pipeline. As of June 1, 1976, after 1,022 days of degasification, over 753 million cubic feet of gas had been drained and 117 million cubic feet of gas had been purchased by the gas company for use in the local community of Wadestown, W. Va. The gas drained to date is six times the gas estimated to be in the area subtended by the holes. Methane emissions at the working face of 1 West mains, Federal No. 2 mine has been reduced by 50 pct, proving the value of methane drainage by horizontal degasification holes drilled from shaft bottoms ahead of mining.

Jan 1, 1976

By J. B. Gayle

The Bureau of Mines sole-heated oven has been used for studying coal expansion for some 20 years. During the period before 1940 emphasis was placed on studies of the mechanism of coal expansion and the effects of variations in operating conditions on the results. Since 1940 emphasis has shifted to a survey of the expansion properties of various coking coals. Because additional information concerning a number of unsolved problems in connection with the earlier studies appeared highly desirable, this investigation of the use of sole-heated ovens for studying coal expansion was undertaken. The principal findings, in order of their discussion in the text, may be summarized as follows. 1. Expansion results for binary blends of coking coals exhibit nonadditive behavior, both positive and negative deviations from additive behavior being noted, depending on the particular coals tested. Additive behavior can be achieved, however, either by charging the blend components in separate layers (which indicates that the observed phenomena are not characteristic of the particular expansion oven used) or by testing relatively coarse sizes of coal (which suggests that the effects of crushing on the expansion properties of coking coals may be even more complex than is generally recognized).

Jan 1, 1959

By G. R. Hopkins

"A new record in fuel efficiency at petroleum refineries was achieved in 1935, when an average of only 615,000 B. t. u. was needed to refine a barrel of crude oil, compared with an average of 638,000 B. t. u. in 1934 and 829,000 B. t. u. In 1925. (See fig. 1.)Refiners have made almost uninterrupted progress in firing efficiency during the last decade although much of this gain was brought about by improved technique and greater use of heat exchangers and pipe stills, the determining factor was the trend in crude runs to stills. Most plants can increase their crude throughput materially with but small increase in fuel consumption. Consequently, in years in which crude runs have increased substantially, average requirements have declined; but in years in which crude runs have decreased, the average has tended upward. This conclusion is confirmed by figure 1, which shows that there has been but one minor exception to this rule in the last 10 years.Technical progress in fuel efficiency may be illustrated by comparing crude runs and total B. t, u. consumed. Between 1925 and 1935 crude runs to stills increased 31 percent, but the total quantity of heat required did not increase; in fact, it declined slightly.The trend of modern still construction is from shell stills, in which a large body of oil is heated, to tube stills, in which the heat comes into much closer contact with the oil. In 1935 the total capacity of operating pipe stills increased about 4 percent; this increase, though small, probably was related to the gain in average efficiency.The Increased use of heat exchangers and their role as fuel savers have been discussed in previous reports of this series. It is sufficient to say that refiners with insufficient exchange capacity added as much in 1935 as their budgets would permit."

Jan 1, 1937

By John Ward Smith

Oil-yield data are presented for core samples from Colorado Corehole No.1, drilled by the Bureau of Mines and the Atomic Energy Commission in a previously untested oil-shale area near the northern edge of Colorado's Piceance Creek Basin. Continuous oil shale 2068 feet thick, averaging 18.41 gallons of oil per ton of shale and representing 1.8 billion barrels of oil per square mile, occurs at the core site.

Jan 1, 1968

By T. R. Jolley

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and, from the data developed, to determine: I. Which coals either as mined or after beneficiation by conventional preparation are chemically suitable under present standards for producing metallurgical coke. 2. Which coals require special and more intensive treatment in preparation than is now practiced. 3. Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation by present-day methods. This report is one in the county series that describes the preparation characteristics of the coals of Bell County, Ky.

Jan 1, 1957

By B. J. Dalton

This report gives general expressions for evaluating various thermo-dynamic properties applicable to a two-component system, including liquid-vapor equilibria. In addition, expressions are developed for some of the quantities useful in making thermodynamic consistency checks on phase equilibria data. These formulas were developed from the general principles of thermodynamics and are expressed in terms of the compressibility factor, which is assumed to be an explicit function of the molal density, the absolute thermodynamic temperature, and the composition.

Jan 1, 1968

By Peter F. Steidl

As part of the Bureau of Mines methane control program, the Upper Free- port coalbed was studied in Fayette County, Pa., where this coalbed lies about 650 feet below the Pittsburgh coalbed and contains the largest remaining reserves of any coalbed in the county. Coal and overburden isopachs, structure and joint pattern maps, and a fence diagram were prepared using data from gas and oil exploration logs and coal outcrops. These maps will aid in determining the need and/or feasibility of degasifying the Upper Freeport coalbed in the study area. Much of the coalbed in this area is under 600 to 1,400 feet of overburden. By correlation with data from the Pittsburgh coalbed, the gas content at depths of this order is estimated to be between 140 to 300 cf/ton of coal, for a total of 190 to 400 billion cubic feet of methane in this coalbed in Fayette County.

Jan 1, 1977

By d&apos, Kathleen J. Amico

THIS SUMMARY is shown in volumes I and III of this series on mineral production in the United States (including Alaska and Hawaii), its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, and on the principal minerals imported into and exported from the United States. For further details on production, see the several commodity and area chapters. A summary table comparing world and U.S. mineral production also is included. [ ]

Jan 1, 1960