Search Documents

By Thomas J. Peters

The U.S. Bureau of Mines studied the 63,9SS-acre Hanson Lakes study area, including the Ten Mile-East and part of the Ten-Mile West RARE II areas, plus additional acreage, all proposed at times for Wilderness designation. The study was part of a Idaho Land Assessment Program with the Idaho Geological Survey and the U.S. Geological Survey, to provide minerals information for land-use decisions, and ensure domestic mineral supplies. The area is at the north end of the rugged Sawtooth Range and includes parts of the Sawtooth National Recreation Area which is closed to mineral location. The Copper Mountain. Elk Mountain, and Observation Peak mineralized areas are in the study area, but only Copper Mountain is open to claim location. It is on the trans-Challis fault zone and contains Tertiary granite which is favorable for mineral deposits of gold, beryllium, niobium, REE (rare-earth elements), tin, molybdenum, copper, silver, and lead. Identified resources are 1.9 million tons of flake graphite at Elk Mountain, but much more graphite occurs in the vicinity REE occurs in 18 black sand placer sites along the lower reaches of study area streams just outside the study area, on Cape Horn Creek, Marsh Creek, and lower Valley Creek flood plains, and at one hydrothermal site near Observation Peak. Hydrothermal REE is commonly low in? by-product thorium. a radioactive disposal problem. Many advanced REE applications enhance the quality of life, and future uses in superconductivity may reduce energy consumption. Seventeen lode, one geothermal, and 11 placer prospects were examined. Workings totaled about 20 adits, one shaft, several open cuts, and numerous small pits. Approximately 500 mining claims have been located or relocated in the study area, including a 200-claim block for disseminated molybdenum.

Jan 1, 1992

By L. J. Froisland

The Bureau of Mines conducted a 4-year research program at Uravan, Colo., on a 2-1/2-acre reclamation plot on the slope of a uranium tailings pile that had been covered with mine waste rock. The purpose of this study was to determine the effects of plant species, type of irrigation, type of fertilizers, and use of dust control chemicals on plant growth and surface coverage. Best grass coverage, nearly 100 percent with 240 plants per square foot, was developed in a section that was seeded with crested wheatgrass, fertilized with sewage sludge, and sprinkler irrigated. For comparison, a section that had been treated with commercial fertilizers developed 3.1 crested wheatgrass plants per square foot and 24 percent coverage without irrigation, and 8 plants per square foot and 75 percent coverage with irrigation. Results of spraying a dust control chemical were inconclusive. Russian-thistle invaded all test sections and ranged in density from 0.6 to 7.3 plants per square foot.

Jan 1, 1982

By Oliver Bowles

The term "stone" in its broader sense includes not only the well-known limestone, marble, granite, sandstone, and slate but also precious and semi precious stones and many minerals and rocks not included in the principal groups. Stones have long been used for structural and ornamental purposes. To be so used, they must be cut to various shapes and sizes, and some must be polished to bring out their inherent attractiveness.

Jan 1, 1958

By Sidney Katell

An estimated capital investment of $76,499,800 will be required for a plant designed and built to produce 90 million standard cubic feet per day (std.c.f.d.) of synthetic pipeline gas through Lurgi gasification of bituminous char. This investment figure does not include the pretreatment plant, the cost of which is assumed to be reflected in the cost of the char fed to the gasification system. Shift conversion, C02 removal, and methanation are required after gasification in the Lurgi unit to make a gas suitable for pipeline transmission. Capital investment data are based upon equipment costs, January 1959. Based on a 90-percent or 330-day operating year, the operating cost before profit and Federal taxes with the char price as a variable will amount to the following: [ ]

Jan 1, 1959

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

CALCULATION OF MINE HEAD LOSSES FROM ALTIMETER SURVEY DATA USBM PENNSYLVANIA STATE UNIVERSITY - MINERAL ENGINEERING DEPARTMENT USBM USBM USBM THIS PROGRAM CALCULATES PRESSURE LOSSES USING THE USBM METHOD GIVEN USBM IN USBH IC 7809 BY MCELROY AND KINGERY.1957. THE MAJOR DIFFERENCE USBM BETWEEN THIS PROGRAM AND THE CITED REFERENCE IS THE TREATMENT OF AIR USBM

Jan 1, 1977

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User's guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992

By Jacob N. Frank

A factorially designed, hydraulic fragmentation experiment using a high-pressure water jet was conducted on concrete blocks. Three levels of pressure, standoff distance, and impact angle and two levels of traverse time and surface condition were used. Three variables were measured: depth of penetration, volume of material removed, and width of slot. Three stepwise linear regression equations were developed from the jet parameters and the physical properties of the concrete. The three basic equations, describing the significant jet parameters and physical properties, were developed into 15 predictor equations, five for each variable investigated. Direct regression equations were also developed for each variable investigated to show the result of increasing or decreasing each significant variable. Energy efficiencies were developed for the experiment and for each significant factorial variable.

Jan 1, 1971

By S. L. Payne, E. F. Foerster, C. W. Schultz, G. R. Zellars

The vapor pressure of copper in a series of liquid copper - nickel alloys was determined by the carrier gas method . The activity and activity coefficient of copper were calculated over the entire range of alloy composition . These data show a slight positive deviation from ideal behavior . The activity coefficient of copper was highest ( 2.10 ) at 0.05 mole fraction copper and approached unity at concentrations above 0.85 mole fraction copper . The results for nickel were calculated from the copper data by the graphical integration of the Gibbs - Duhem equation .

Jan 1, 1964

By W. P. Stroud

In this U.S. Bureau of Mines report, the conditions required for the direct reconstruction of a tomogram from observed line integrals are examined. Because of the limited access to the working faces in coal mines, the special case of access to only two opposite faces is emphasized. Classical matrix methods were used for small dimensional (2 by 2, 3 by 3, and 4 by 4) applications to determine the limitations and the requirements for a solution. The results for large (n by n) grids were then inferred and generalized from those of the smaller grids and matrices. Limited access tomography is found to be appropriate for in-seam hazard detection from seismic and microwave data, but it is shown that additional data must be added to obtain a direct solution.

Jan 1, 2010

By P. A. Wasson, M. M. Fine

Roasting research involving small , batch experiments was conducted to explore the use of solid reductants for converting nonmagnetic iron ore to a magnetic type . Three typical Minnesota ores were tested with one or more of the following reductants : Lignite , lignite chars , anthracite , bituminous coal , petroleum coke , peat , and pyrite . Reductive roasting was accomplished in a 3- by 4- inch externally heated rotating drum . Ore and reductant were placed in the drum and heated to a desired temperature , which was maintained for a predetermined period . Recoveries of over 90 percent of the iron in magnetic concentrates were achieved at 650 ° C , using lignite , some lignite chars , a high- volatile bituminous coal , peat , and pyrite . Pyrite is a novel reductant , which is superior to carbonaceous materials other than lignite and some chars .

Jan 1, 1963

By William C. McBee

Prompted by forecasts of a sulfur oversupply, the Bureau of Mines, U.S. Department of the Interior, is conducting research on potentially large-scale uses of this commodity to extend or replace such construction materials as asphalt, cement, and mineral aggregates. Through these efforts, paving materials have been developed in which sulfur replaces up to 50 pct of the asphalt normally present and which can be prepared and placed with existing mixing and paving equipment. Laboratory properties and design methods for this direct mixing process are described along with properties obtained on small-and large-scale field demonstration projects. These properties are compared with those obtained from control materials prepared without sulfur additions. Monitoring for toxic gases during laboratory and commercial mixing and paving operations is discussed also.

Jan 1, 1978

By A. C. Fieldner

The Bureau of Mines has recently conducted a study of results obtained in analyzing similar samples of coal and coke by 25 laboratories throughout then country, in comparison with results obtained in the Bureau's coal laboratory at Pittsburgh. The purpose of this work was primarily to obtain a comparison of the methods of coal analysis used by the laboratories of the American Gas Association. Therefore, four standard samples of coal end one of coke ware prepared in the Bureau of Mines coal laboratory at Pittsburgh, and portions sent to each laboratory. At the same time, a like number of standard samples were submitted to 12 commercial laboratories rot affiliated with the Association, for the purpose of comparing their analyses with the results is obtained by the U. S. Bureau of Mines and the American Gas Association. Tire comparison is based on the average of 24 analyses by the Bureau of Mines on each kind of coal, and the accompanying curves show the deviation from this average analysis, together with deviations from the check limits of the American Society for Testing Materials.

Jan 1, 1923

By A. R. Taylor

The Bureau of Mines has determined the heat capacity and enthalpy values for beryllium sulfate (BeS04) throughout the temperature ranges of 10° to 300° K in an adiabatic calorimeter, and 350° to 860° K in a Bunsen-type ice calorimter, The heat-capacity data were extrapolated to 0° K, and smooth values of heat capacity, entropy, enthalpy function, and free-energy function were reported at 10-degree intervals between 0° and 300° K. The method of least squares was used to fit the enthalpy data with an algebraic equation. The equation also was used to calculate values of heat capacity, entropy, enthalpy function, and free-energy function at 50-degree intervals between 300° and 900° K.

Jan 1, 1963

By R. H. Sprute

The Federal Bureau of Mines performed laboratory tests using direct current to dewater and densify fine-grained coal sludge in order to alleviate disposal problems and lead to recovery of high energy value often present in this waste. The laboratory tests described in the main body of the report were performed on thickened underflow (no flucculant added) from a northern Appalachian coal preparation plant. Solids in this slurry was very fine with 65 percent of the particles less than 0.1 mm in diameter. A variety of application procedures tested is exemplified by a test in which a soupy slurry (55 percent dry-weight moisture content) was converted into a firm dense material with a 20-percent dry-weight moisture content. These results were achieved in 3 hours with current density of 3.7 amp/ft2 and a power expenditure of 35 kwhr/yd3. The treated material has an average heating value of 10,400 Btu/lb. Varying current density, electrode configuration, and placement depth makes application of the treatment flexible. Two other types of sludge were tested briefly--thickener underflow from a southern Appalachian coal preparation plant with flocculant added, and sludge from an acid mine drainage treatment plant. The underflow responded well to the treatment, but response of the sludge from the acid mine drainage treatment plant was poor.

Jan 1, 1976

By M. R. Geer

The ever-increasing need to guard against stream pollution has intensified interest in the problems of handling and disposing of flotation tailing. Therefore, the Bureau of Mines investigated the possibility of using crushed washery refuse to adsorb the free water in thickened flotation tailings on a bench scale and then in a pilot plant because the conventional methods of disposing of coal flotation tailings--impounding them or filtering them so they are dry enough to be conveyed to the refuse dump--are sometimes either impractical because of space limitations or costly because of low filter capacity. Most of the refuse samples tested were of similar mineralogical composition and exhibited similar water retention capability. The amount of crushed refuse required to adsorb the water in a particular tailing was influenced greatly by the fineness of the solids in the tailing and hence the percentage of solids to which it could be thickened. The ratio of crushed refuse to tailing solids required to provide a mixture dry enough to be carried on an inclined conveyor belt varied from 2.4 to 6.4. Several chemical agents that were tested were very effective in turning the free water in tailings into a stable gel. Fly ash also was very effective in adsorbing water.

Jan 1, 1968

By John Millhiser, Margaret Bonarek, Dennis McLaughlin

This report contains a description of the contract activities performed by ENSCO, Inc. under contract No. H0178069. The purpose of this project was to enhance the Bureau of Mine's Cableless Electronic Survey System use to aid in the drilling of long (approx. 2000 feet) boreholes in coal. This drilling is performed as part of the methane drainage program. The system that was ultimately developed was field tested and demonstrated in actual in-mine drilling activities. The significance of this system as compared to previous drill survey systems is the fact that it surveys without having to be inserted and removed for each survey point. It is so designed that it can withstand the shock and vibration experience by the drill string during drilling. This means an increased productivity is now possible in that drill operators can determine drill bit positioning in a near real-time environment.

By Gloria L. Walker

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1990

By M. Howard Berliner

"INTRODUCTION During the last 4 months of 1943, the Bureau of Mines engaged in an investigation and exploratory drilling program in the area between the Coughlin and Galena Level mines near the town of Shullsburg, in Lafayette County, Wisconsin. The work was undertaken as part of a general Bureau of Mines investigation of the zinc-producing area of southwestern Wiscon¬sin at a time when an effort was being made to increase the production of metals important to the Nation's war program.The portion of the southwest Wisconsin zinc district in the immediate vicinity of Shullsburg and the Coughlin and Galena Level mines is well mineralized. The principal ore horizon is at shallow depth, and there is evidence that relatively extensive surface mining for lead was done over a period of many years. Underground mining' for lead and zinc has continued to the present time.The Bureau undertook an exploratory drilling program in the area immediately west and southwest of the Coughlin mine workings after thorough preliminary investigations and geologic studies indicated that such work would serve to guide operators in the development of new ore reserves needed for continuance of mining operations in that area."

Apr 1, 1947

By V. E. Erwin, W. W. Adams

"INTRODUCTION This report presents statistics of accidents at coke ovens in the United States during the calendar years as 1933, the twenty-first year for which data of this kind are available, 1913 being the first year for which accident reports were collected from the operating companies by the Bureau of Mines. The present report is presented in mimeograph form because insufficient funds are available for printing it. The first report of the Bureau of Mines that contained statistics of accidents for the coke-mining industry in the United States covered the two calendar years, 1913 and 1914. While the figures presented therein related both to beehive and by-product ovens, the original returns from the operating companies were not classified so as to permit the presentation of accident statistics for each class of ovens separately. Beginning with 1915, the accident reports from the operating companies have shown the general type of ovens to which the reports related; therefore, since that year, separate statistics for each of the two classes of ovens have been given in the Bureau's yearly reports of accidents at coke ovens.The coke-making industry in the United States established a safety record in 1933 almost equal in merit to that which it achieved in 1932, when the accident-frequency rate was the lowest and therefore the most favorable that the industry has known. Credit for the achievement is due almost entirely to companies operating byproduct ovens. (See table 8.)"

Mar 1, 1935

By R. F. Tenney

No detailed information has been published heretofore on the performance of small industrial-type anthracite stokers in building-heating service, apparently because of the difficulty of comparing the performance of one unit with that of another over an entire season's operation. Studies of competitive heating fuels have been similarly handicapped, and attempts to compare fuels are seldom technically sound in this investigation, the performance of a 60-in. Losch4 stoker burning rice-size anthracite in a standard commercial boiler was observed during a 4-month winter-spring season. It was used to heat two buildings at the Bureau of Mines' Anthracite Research Center at Schuylkill Haven, Pa., with the customary type of automatic pressure-range control. Attendance was limited to inspecting, fuel weighing, data recording, and ash removal. Results were computed daily and grouped by weekly periods to minimize daily irregularities. The same stoker-boiler unit had already been tested in a series of American Society of Mechanical Engineers (ASME) test code runs, with the stoker running continuously and with other conditions well stabilized A comparison of results from the code test and the building-heating tests provided information not available in the past for a single stoker unit, assisted in analyzing heat losses not computable in a cyclic operation, and established a basis for evaluating stoker performance in heating service.

Jan 1, 1963